NAPOLEON BK4B3142 Le manuel du propriétaire

Marque: NAPOLEON

Modèle: BK4B3142

Catégorie: Cheminées

Taper: Le manuel du propriétaire

FRENCH

PG. 27

W415-1867 / B / 02.07.19

Oakville™ Series

(GDIX3 illustrated)

- Do not store or use gasoline or other ﬂ ammable vapors and liquids in the vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbour’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁ re department.

•

- Installation and service must be performed by a qualiﬁ ed installer, service agency, or the supplier.

WARNING

ENGLISH

For indoor use only

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, death, or property damage.

OWNER’S MANUAL

SAFETY INFORMATION

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone 1 (866) 820-8686 • www.napoleon.com • [email protected]

f i r e - p a r t s . c o m

W415-1867 / B / 02.07.19

safety information

• This appliance is hot when operated and can cause

severe burns if contacted.

• Any changes to this appliance or its control can be

dangerous and are prohibited.

• Do not operate appliance before reading and

understanding operating instructions. Failure

to operate appliance according to operating

instructions could cause ﬁ re or injury.

• Risk of ﬁ re or asphyxiation do not operate appliance

with ﬁ xed glass removed.

• Do not connect 110 volts to the control valve.

• Risk of burns. The appliance should be turned off

and cooled before servicing.

• Do not install damaged, incomplete or substitute

components.

• Risk of cuts and abrasions. Wear protective gloves

and safety glasses during installation. Sheet metal

edges may be sharp.

• Children and adults should be alerted to the

hazards of high surface temperature and should

stay away to avoid burns or clothing ignition.

• Young children should be carefully supervised

when they are in the same room as the appliance.

Toddlers, young children, and others may be

susceptible to accidental contact burns. A

physical barrier is recommended if there are at

risk individuals in the house. To restrict access to

an appliance or stove, install an adjustable safety

gate to keep toddlers, young children and other at

risk individuals out of the room and away from hot

surfaces.

• Clothing or other ﬂ ammable material should not be

placed on or near the appliance.

• Due to high temperatures, the appliance should be

located out of trafﬁ c and away from furniture and

draperies.

• Ensure you have incorporated adequate safety

measure to protect infants/toddlers from touching

hot surfaces.

• Even after the appliance is out, the glass and/or

screen will remain hot for an extended period of

time.

• Check with your local hearth specialty dealer

for safety screens and hearth guards to protect

children from hot surfaces. These screens and

guards must be fastened to the ﬂ oor.

• Any safety screen, guard or barrier removed for

servicing the appliance, must be replaced prior to

operating the appliance.

• The appliance is a vented gas-ﬁ red appliance. Do

not burn wood or other materials in the appliance.

• The appliance area must be kept clear and free

from combustible materials, gasoline and other

ﬂ ammable vapors and liquids.

WARNING

• Under no circumstances should this appliance be

modiﬁ ed.

• This appliance must not be connected to a chimney

ﬂ ue pipe serving a separate solid fuel burning

appliance.

• Do not use this appliance if any part has been

under water. Immediately call a qualiﬁ ed service

technician to inspect the appliance and to replace

any part of the control system and any gas control

which has been under water.

• Do not operate the appliance with the glass door

removed, cracked or broken. Replacement of the

glass should be done by a licensed or qualiﬁ ed

service person.

• Do not strike or slam shut the appliance glass door.

• When equipped with pressure relief doors, they

must be kept closed while the appliance is

operating to prevent exhaust fumes containing

carbon monoxide, from entering into the home.

Temperatures of the exhaust escaping through

these openings can also cause the surrounding

combustible materials to overheat and catch ﬁ re.

• Only doors / optional fronts certiﬁ ed with the unit

are to be installed on the appliance.

• Keep the packaging material out of reach of

children and dispose of the material in a safe

manner. As with all plastic bags, these are not toys

and should be kept away from children and infants.

• As with any combustion appliance, we recommend

having your appliance regularly inspected and

serviced as well as having a carbon monoxide

detector installed in the same area to defend you

and your family against carbon monoxide.

• Ensure clearances to combustibles are maintained

when building a mantel or shelves above the

appliance. Elevated temperatures on the wall or

in the air above the appliance can cause melting,

discolouration or damage to decorations, a T.V. or

other electronic components.

• A barrier designed to reduce the risk of burns from

the hot viewing glass is provided with this appliance

and shall be installed.

• If the barrier becomes damaged, the barrier shall

be replaced with the manufacturer’s barrier for this

appliance.

• Installation and repair should be done by a qualiﬁ ed

service person. The appliance should be inspected

before use and at least annually by a professional

service person. More frequent cleaning may be

required due to excessive lint from carpeting,

bedding material, etc. It is imperative that control

compartments, burners and circulating air

passageways of the appliance be kept clean.

WARNING:

This product can expose you to chemicals including lead and lead compounds,

which are known to the State of California to cause cancer, and chemicals including carbon

monoxide, which are known to the State of California to cause birth defects or other reproduc-

tive harm. For more information, go to www.P65Warnings.ca.gov.

f i r e - p a r t s . c o m

W415-1867 / B / 02.07.19

table of contents

congratulations 4

1.0 getting to know your appliance 5

1.1 control access 6

1.2 rating plate information 6

2.0 operating your appliance 7

2.1 using your appliance (millivolt only) 7

2.2 on/off components 7

2.2.1 changing the batteries 8

2.3 bracket installation for optional F45/60 receiver (GDI3 only) 8

3.0 operation (millivolt) 9

4.0 operation (electronic) 10

4.1 extreme cold lighting instructions 10

5.0 remote control layout 11

5.1 general transmitter layout 11

5.2 split ﬂ ow (GDIX4 only) 11

5.3 initializing the transmitter / battery holder for the ﬁ rst time 11

5.4 temperature display 12

5.5 ﬂ ame height 12

5.6 blower speed 12

5.7 night light dimmer control 12

5.8 in the event of a power failure 12

5.9 key lock 13

5.10 eFIRE Controller application 13

5.11 low battery 13

5.12 battery holder / backup installation 13

6.0 clearances around fireplace 14

7.0 maintenance 16

7.1 care of glass 17

7.2 care of plated parts 17

7.3 safety barrier and glass door removal / installation 18

8.0 replacement parts 19

9.0 accessories for GDI3 / GDIG3/ GDIX3 20

10.0 accessories for GDIX4 22

11.0 troubleshooting 24

12.0 warranty 25

This owner’s manual is written for a complete series of ﬁ replaces that have a variety of different features and speci-

ﬁ cations. Before reading this manual, be sure you know which model of ﬁ replace that you have. This information

will have been ﬁ lled out by the installer on the following page and on the rating plate that is permanently attached

to the ﬁ replace (see “rating plate information” section).

This manual is for the:

• Oakville™ Series (GDI3 / GDIG3 / GDIX3 / GDIX4 models)

If required, more detailed technical information is included in the ﬁ replace installation manual.

The information throughout this manual is believed to be correct at the time of printing. Wolf Steel Ltd. reserves

the right to change or modify any information within this manual at any time without notice. Changes, other than

editorial are denoted by a vertical line in the margin.

Visit the Napoleon website for the most current version of your appliance’s manual.

f i r e - p a r t s . c o m

W415-1867 / B / 02.07.19

welcome

Dealer Information

Name of Dealer:

Dealer Location:

Dealer Phone:

Dealer E-mail:

Customer:

Customer Address:

Date of Installation:

Location of the appliance:

Installer:

Napoleon is proudly committed to your total home comfort. We are proud to say that our products continunously

surpass industry standards and our inspiration is you! More than anything, we want you to feel conﬁ dent in

choosing Napoleon for your home. Our products are designed to provide that conﬁ dence and ensure that every

Napoleon product is beyond compare.

Napoleon products are designed with superior components and materials assembled by trained craftsmen who

take great pride in their work.

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with the appliance for your

safety. This barrier must be installed.

Your Napoleon ﬁ replace has been thoroughly inspected by a qualiﬁ ed technician before packaging to ensure that

you, the customer, receives the quality product that you expect from Napoloen.

Dealer : Fill in your dealer information (or business card) and the appliance installation information

below.

congratulations

Model:

Serial Number:

Dealer: Business card location

Natural Gas: GDI3N

GDIG3N

GDIX3N

GDIX4N

Propane: GDI3P

GDIG3P

GDIX3P

GDIX4P

f i r e - p a r t s . c o m

W415-1867 / B / 02.07.19

getting to know your appliance

1.0 getting to know your appliance

Burner

Pilot

Safety barrier Glass door

Valve / battery

back up /

anticondensation

switch

Some features and locations may vary depending on the model.

note:

HOT GLASS WILL CAUSE BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

DANGER

A barrier designed to reduce the risk of burns from

the hot viewing glass is provided with this appliance

and shall be installed for the protection of children

and other at-risk individuals.

The area above the ﬁ replace opening including the safety barrier, barrier frame and

the surface of the wall can get very hot during operation and should never be touched

until the appliance is off and completely cooled.

Vent Slide

Rating plate

/ lighting

instructions

Gas

Inlets

(Front

and

Back)

f i r e - p a r t s . c o m

W415-1867 / B / 02.07.19

getting to know your appliance

1.1 control access

This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.

1.2 rating plate information

The rating plate must remain with the appliance at all times. It must not be removed.

note:

9700539 (WSL) 4001658 (NAC) 4001657 (NGZ) 4001659 (WUSA)

WOLF STEEL LTD. 24 Napoleon Road, Barrie, ON, L4M 0G8 Canada

MODEL / MODÈLE

Altitude

Input

Reduced Input

Élévation

Alimentation

Alimentation Réduite

WARNING: Do not add any material to the appliance which will come in contact with the

ﬂames, other than that supplied by the manufacturer with the appliance.

AVERTISSEMENT: N’ajoutez pas à cet appareil aucun matériau devant entretien

contact avec les ﬂammes autre que celui qui est fourni avec cet appareil par le fabricant.

The appliance must be vented using the appropriate Napoleon vent kits. See installation

manual for venting speciﬁcations. Proper reinstallation and resealing is necessary after servicing

the vent-air intake system.

L’appareil doit être ventilé à l’aide de l’ensemble d’évacuation propre à Napoleon. Référez au

manuel d’installation pour les spéciﬁcations d’évacuation. Il est nécessaire de bien réinstaller et

resceller l’évacuation après avoir executer l’entretien du système de prise d’air.

Serial Number / N° de Série:

W385-2310 / B

GDIG3 / CDIG3

Electrical rating: 115V, 60HZ. Less than 12 amperes.

Spéciﬁcations électriques: 115V, 60HZ. Moins de 12 ampère.

GDIG3N CDIG3N CDIG3P GDIG3P

0 - 4500ft (0 - 1370m)

24,000 BTU/h

17,000 BTU/h

61.7%

THIS VENTED GAS FIREPLACE HEATER IS NOT FOR

USE WITH AIR FILTERS. FOR USE WITH GLASS

DOORS CERTIFIED WITH THE APPLIANCE ONLY.

NOT FOR USE WITH SOLID FUEL.

REFERENCE# 161746

NE PAS UTILISER DE FILTRE À AIR AVEC CE FOYER

AU GAZ À ÉVACUATION. POUR UTILISATION

UNIQUEMENT AVEC LES PORTES EN VERRE CER-

TIFIÉES AVEC L’APPAREIL. NE PAS UTILISER AVEC

DU COMBUSTIBLE SOLIDE.

Manifold Pressure: 3.5” w.c. (NG)

Minimum Supply Pressure: 4.5” w.c. (NG)

Maximum Supply Pressure: 7” w.c. (NG)

Pression au Collecteur: 3,5” d’une colonne d’eau (GN)

Pression d’Alimentation Min.: 4,5” d’une colonne d’eau (GN)

Pression d’Alimentation Max.: 7” d’une colonne d’eau (GN)

Manifold Pressure: 10” w.c. (P)

Minimum Supply Pressure: 11” w.c. (P)

Maximum Supply Pressure: 13” w.c. (P)

Pression au Collecteur: 10” d’une colonne d’eau (P)

Pression d’Alimentation Min.: 11” d’une colonne d’eau (P)

Pression d’Alimentation Max.: 13” d’une colonne d’eau (P)

WARNING: For installation into a vented non-combustible

appliance only.

Minimum appliance size:

Height 20 15/16”

Depth 14 3/8”

Width 28 5/8”

Minimum inside ﬂue size:

6”

Minimum distance from bottom of a combustible mantel

projecting a maximum of 3” from the wall to the top of the

appliance:

12”

See installation manual for greater extensions.

ATTENTION: Pour installation dans un appareil ventilé en

maçonnerie seulement.

Dimensions minimales de l’appareil:

Hauteur 20 15/16”

Profondeur 14 3/8”

Largeur 28 5/8”

Diamètre intérieur minimales de conduit d’évacuation:

6”

Distance minimale entre le dessous d’une tablette

décorative combustible, qui ressort un maximum de

3 po, et le dessus de l’appareil:

12”

Voir la manuel d’installation pour les extensions plus grandes.

20,000 BTU/h

Certiﬁed to Canadian and American National Standards: CSA 2.33-2016 / ANSI Z21.88-2016 for Vented Gas Fireplace Heaters

Certiﬁé selon les normes Nationales Canadiennes et Américaines: CSA 2.33-2016 / ANSI Z21.88-2016 pour Foyer au gaz à évacuation

Direct vent, vented gas appliance. Approved for bedroom, bathroom and bed-sitting room installation. Suitable for mobile home installation, if installed in

accordance with the current standard CAN / CSA Z240MH Series gas equipped mobile homes in Canada, or, in the United States, the Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280. When this US Standard is not applicable, use the Standard for Fire Safety Criteria for Manufactured

Home Installations, Sites and Communities, ANSI / NFPA 501A. This appliance must be installed in accordance with local codes, if any; if none, follow the current

ANSI Z223.1 or CSA B149. For use with barrier W565-0318. Follow installation instructions.

Appareil à gaz ventilé. Homologué pour installation dans une chambre à coucher, une salle de bain et un studio. Approprié pour installation dans une maison mobile

si son installation conforme aux exigences de la norme CAN / CSA Z240MH Séries de maisons mobile équipées au gaz en vigueur au Canada, ou, aux États-Unis

selon la norme 24 CFR, Part 3280, Manufactured Home Construction and Safety Standard. Dans le cas ou cette norme d’États-Unis n’est pas pertinentes, utiliser

la norme NFPA 501A, Fire Safety Criteria for Manufactured Home Installations, Sites and Communities. Installer l’appareil selon les codes ou règlements locaux ou,

en l’absence de tels règlements, selon les codes d’installation ANSI Z223.1 ou CSA B149 en vigueur. Utiliser uniquement avec l’écran W565-0318. Suivre les

instructions d’installation.

CERTIFIED FOR

CERTIFIÉE POUR

CANADA

USA

CERTIFIED

CAUTION:

Hot while in operation. Do not touch. Severe

burns may result. Keep children, clothing,

furniture, gasoline and other liquids having

ﬂammable vapors away.

ATTENTION:

L’appareil est chaud lorsqu’il fonctionne. Ne pas

toucher l’appareil. Risque de brûlures graves.

Surveiller les enfants. Garder les vêtements, les

meubles, l’essence ou autres liquides produisant

des vapeur inﬂammables loin de l’appareil.

S’assurer que le brûleur et

le compartiment des

commandes sont propres.

Voir les instructions

d’installation et

d’utilisation qui

accompagnent l’appareil.

Par mesure de sécurité,

cet appareil doit être

alimenté en air frais et

avec d’air

comburant et de

ventilation sufﬁsant.

This appliance is only for use with the type of gas

indicated on the rating plate and may be installed

in an aftermarket, permanently located, manufac-

tured home (USA only) or mobile home where not

prohibited by local codes. See owner’s manual

for details. This appliance is not convertible for

use with other gases, unless a certiﬁed kit is

used.

Cet appareil doit être utilisé uniquement avec le

type de gaz indiqué sur la plaque signalétique.

Cet appareil peut être installé dans une maison

préfabriquée ou mobile (É.U. seulement) installée

à demeure si les règlements locaux le permettent.

Voir la notice de l’utilisateur pour plus de

renseignements. Cet appareil ne peut pas être

utilisé avec d’autres gaz sauf si une trousse de

conversion certiﬁée est fournie.

FOR YOUR SAFETY:

Do not store or use gasoline or

other ﬂammable vapors and liquids

in the vicinity of this or any other

appliance.

CAUTION:

Do not operate the appliance with

the glass removed, cracked or

broken.

Replacement of the glass should

be done by a licensed or qualiﬁed

person.

POUR VOTRE

SÉCURITÉ:

Ne pas entreposer ni utiliser

d’essence ni d’autres vapeurs ou

liquides inﬂammables dans le

voisinage de cet appareil ou de

tout autre appareil.

ATTENTION:

N’utiliser pas l’appareil si le

panneau frontal en verre est

enlevé, craqué ou brisé.

Remplacement du panneau frontal

en verre doit être fait par un

technicien agréé.

WARNING:

Improper installation,

adjustment, alteration,

service or maintenance can

cause property damage,

personal injury or loss of life.

Refer to owner’s manual.

Installation and service must

be performed by a qualiﬁed

installer, service agency or

the gas supplier.

AVERTISSEMENT:

Un installation

ou une modiﬁcation

inappropriée du réglage, du

service et de l’entretien

pourraient être la cause de

dommages à la propriété de

blessures corporelles ou

même la mort. Consulter le

manuel d’information,

l’installation et le service

doivent être exécutés par un

installateur qualiﬁé pour le

gaz, un entreprise de

service ou le fournisseur de

gaz seulement.

Keep burner and control

compartment clean. See

installation and

operating instructions

accompanying

appliance. Appliance

needs fresh air for safe

operation and must be

installed with adequate

provisions for

combustion and

ventilation air.

SAMPLE

L4M 0G8 CanadaCanada

WARNIN

GWARNING

Do not add any material to the appliance wDo not add any material to the appliance

ﬂames, other than that supplied by the manufacturer with tﬂames, other than that supplied by the manufacturer with

VERTI

EMEN

TAVERTISSEMENT

N’ajoutez pas à cet appN’ajoutez pas à cet ap

contact avec les ﬂammes autre que celui qui est fountact avec les ﬂammes autre que celui qui est fo

The appliance must be vented using the appropriappliance must be vented using the approp

manual for venting speciﬁcations. Proper reinstual for venting speciﬁcations. Proper rein

the vent-air intake system

.vent-air inta

L’appareil doit être ventilé à l’aide de l’ensL’appareil doit être ventilé à l’aide de l’e

manuel d’installation pour les spéciﬁcamanuel d’ins

resceller l’évacuation après avoir exresceller l

Serial Number / NSerial N

Electrical rating: 115V, 60HZ. LesElectric

Spéciﬁcations électriques: 115Spé

AS FIREPLACE HEATER IS NOS FIREPLACE HEATER

R FILTERS. FOR USE WITH GLASSTERS. FOR USE WITH GLASS

RTIFIED WITH THE APPLIANCE ONLY. WITH THE APPLIANCE ONLY.

R USE WITH SOLID FUEL.OLID FUEL.

AS UTILISER DE FILTRE À AIR AVEC CE FORE À AIR AVEC CE F

GAZ À ÉVACUATION. POUR UTILISATIONGAZ À ÉVACUATION. POUR UTILISATIO

UNIQUEMENT AVEC LES PORTES EN VERNIQUEMENT AVEC LES PORTES EN VE

TIFIÉES AVEC L’APPAREIL. NE PAS UTIIÉES AVEC L’APPAREIL. NE PAS UT

MBU

TIBLE

LIDE

.OMBUSTIBLE SOLIDE.

u (P)

ntilé enen

eulement.lement.

e l’appareil:l’appareil:

teur 20 15/16”eur 20 15/16”

rofondeur 14 3/8”fondeur 14 3/8

eur 28 5/8

”Largeur 28

conduit d’évacuation:nduit d’évac

6”

le dessous d’une tablettedessous d’une ta

, qui ressort un maximum deort un maximum

3 po, et le dessus de l’appareil:po, et le dessus de l’appareil:

2”

12”

llation pour les extensions plus grandes.ation pour les extensions plus grandes.

ED FORD FOR

FIÉE POURIÉE POUR

CANADA

CAUCAU

Hot while in Hot wh

burns mburns

furnitufurni

S’assurer

ue le brûleur et

S’assurer que le brûleur et

e compartiment des

le compartiment des

ommandes sont propres. mmandes sont propres.

Voir les instructions nstructions

’installation et stallation et

ilisation qui ilisation qui

nent l’ap

de s

SAM

WARNIN

G:WARNING:

Improper installation,

proper installation,

djustment, alteration,

ment, alteration,

rvi

r m

int

aintenance

cause property damage,

ty damage,

ersonal injury or loss of life.

personal injury or loss of life.

r t

’s

Refer to owner’s manual.

Installation and service must nstallation and service must

be performed by a qualiﬁedbe performed by a qualiﬁ

installer, service agencyinstaller, service agenc

the gas suppliethe gas supplie

AVERTISSAVE

Un inU

ou unou u

inapprapp

ons ons

ng g

ppliance nce

air for safe safe

n and must be be

ed with adequate te

provisions for provisions

on an

combustion

entilation air.

ventilati

Left side view of appliance

(GDIG3 illustrated)

f i r e - p a r t s . c o m

W415-1867 / B / 02.07.19

operating your appliance

2.0 operating your appliance

To turn the appliance on:

When operating your appliance for the ﬁ rst time, there is a required burn-in process that cures materials used

to manufacture the ﬁ replace that may emit both vapors and an odor. These are normal when operating a new

appliance for the ﬁ rst time. Ensure adequate air circulation is provided during burn-in process, if this was not

completed by the installer during installation.

2.1 using your appliance (millivolt only)

A Turn the gas knob to pilot.

B Depress slightly and hold gas knob while lighting the pilot with the push button ignitor. Keep knob depressed

for one minute then release.

C With the pilot lit, depress knob and turn gas knob counter clokcwise to “ON”.

D Turn the on/off switch on (see below).

E After 3-5 seconds, the control will start a spark at the pilot, light the pilot and then the burner. The spark

period will last 60 seconds, or until the pilot has lit.

F When used for the ﬁ rst time, if the burn-in process was not completed by the installer; run appliance

continuously for 4 hours (burn-in).

G Turn the appliance off. Wait until appliance is completely cool before moving to the next step.

H Remove the safety barrier and ﬁ rebox glass door. Clean ﬁ rebox glass door (see “maintenance” section).

Replace ﬁ rebox glass door and safety barrier.

For more detailed information, see your installation manual or contact your authorized dealer.

2.2 on/off components

Batteries must be disposed of according to the local laws and regulations. Some batteries may be

recycled, and may be accepted for disposal at your local recycling center. Check with your

municipality for recycling instructions.

| On/off switch | Battery holder (including switch) | Remote control |

(Standard for GDIX3 / GDIG3 / GDIX4)

(Not supplied)

(Optional for GDI3)

(Standard for GDIX3 / GDIG3 / GDIX4)

f i r e - p a r t s . c o m

W415-1867 / B / 02.07.19

operating your appliance

1. Remove the right access panel from the side of the appliance.

2. Remove the front 2 screws from the inside edge (Fig. 2) and swing the

control door open.

3. Remove the 2 screws holding the receiver in place.

4. Remove the receiver and replace.

2.2.1 changing the batteries

• Ensure the gas and electrical power to the appliance is turned off.

• Appliance may be hot, do not service until the appliance has cooled.

WARNING

4 AA batteries must be installed into the receiver before the appliance can

operate by battery backup. The receiver is located in the bottom right corner

of the appliance (Fig. 1).

note:

Ensure the 3 position slider switch is in the "REMOTE" position (middle

position).

Fig. 1

Fig. 2

GDIG3 Illustrated

note:

If your opening is too small, you may need to pull the appliance out

slightly.

Receiver Removal

1. Remove the safety barrier and glass door (see "safety barrier & door removal / installation" section).

2. Remove the 1 screw holding the bracket in place (Fig. 1). Lift the bracket up and out of the slots, lifting it

through the opening between the ﬁ rebox and the appliance's outer shell (Fig. 2).

3. Insert optional receiver (F45 or F60). Secure the receiver using 2 screws (supplied).

4. Place the bracket and receiver back through the opening between the ﬁ rebox and the appliance's outer shell.

Slide the bracket and receiver into and down the slots (Fig. 2 in reverse).

5. Resecure the 1 screw to hold the bracket and receiver in place (Fig. 1).

Fig. 1

Fig. 2

Firebox

Outer Shell

2.3 bracket installation for optional F45/60 receiver (GDI3 only)

f i r e - p a r t s . c o m

W415-1867 / B / 02.07.19

operating your appliance

3.0 operation (millivolt)

WARNING

• Do not turn on if children or other at risk individuals are near the appliance.

• This appliance is equipped with a pilot which must be lit by hand while following these instructions exactly.

• Before operating, smell all around the appliance area for gas and next to the ﬂ oor because some gas is heavier

than air and will settle on the ﬂ oor.

• Use only your hand to turn the gas control knob. Never use tools. If the knob will not turn by hand, do not try

to repair it. Call a qualiﬁ ed service technician. Force or attempted repair may result in a ﬁ re or explosion.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁ ed service technician

to inspect the appliance and replace any part of the control system and any gas control which has been

underwater.

FOR YOUR SAFETY READ BEFORE LIGHTING

WHAT TO DO IF YOU SMELL GAS

LIGHTING INSTRUCTIONS

TO TURN OFF GAS

A. Stop! Read the above safety information on this label.

B. Remove batteries from the transmitter and set thermostat to lowest setting, if equipped.

C. Turn off all electrical power to the appliance.

D. Open the glass door, if equipped.

E. Turn the gas knob clockwise to the “OFF” position.

F. Wait ﬁ ve (5) minutes to clear out any gas. If you smell gas including near the ﬂ oor, STOP!

Follow the instructions above in the “WHAT TO DO IF YOU SMELL GAS” section. If you

don’t smell gas; close the glass door and go to the next step.

G. If the appliance is equipped with ﬂ ame adjustment valve turn clockwise to “OFF”.

H. Turn gas knob counter-clockwise to the “PILOT” position. (If the appliance is equipped

with an “ON/OFF” switch, ensure it is in the “ON” position.

I. Depress and hold gas knob while lighting the pilot with the push button ignitor. Keep knob

fully depressed for one minute, then release. If pilot does not continue to burn, repeat steps

E through I.

J. With pilot lit, turn gas knob counter-clockwise to the “ON” position.

K. If equipped with the ﬂ ame adjustment valve, push and turn the knob to high.

L. Turn on all electrical power to the appliance and re-install the batteries into the transmitter, if

equipped. Set thermostat to desired setting, if equipped.

A. Set thermostat to desired setting, if equipped.

B. Turn off all electrical power to the appliance if service is to be performed.

C. Push in gas knob slightly and turn clockwise to the “OFF” position. Do not force.

• Turn off all gas to the appliance.

• Open windows.

• Do not try to light any appliance.

• Do not touch any electric switch; do not use

any phone in your building

• Immediately call your gas supplier from a

neighbour’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call

the ﬁ re department.

• If you do not follow these instructions exactly, a ﬁ re or explosion may result causing property damage, personal

injury, or loss of life.

• If applicable, always light the pilot whether for the ﬁ rst time or if the gas supply has run out with the glass door

opened or removed.

add gas knob

add gas valve

Ensure that a continuous gas ﬂ ow is at the burner before installing the door. When lit for the ﬁ rst time, the appliance

will emit an odor for a few hours. This is a normal temporary condition caused by the “burn-in” of paints and

lubricants used in the manufacturing process and will not occur again. After extended periods of non-operation

such as following a vacation or a warm weather season, the appliance may emit a slight odor for a few hours. This

is caused by dust particles in the heat exchanger burning off. In both cases, open a window to sufﬁ ciently ventilate

the room.

For vent free appliances ONLY: if the appliance shuts off, do not relight until you provide fresh air. If appliance

keeps shutting off, have it serviced. Keep burner and control compartment clean.

note:

When lighting and re-lighting, the gas knob cannot be turned from pilot to off unless the knob is

depressed.

f i r e - p a r t s . c o m

W415-1867 / B / 02.07.19

operating your appliance

4.0 operation (electronic)

WARNING

• Do not turn on if children or other at risk individuals are near the appliance.

• This appliance is equipped with an ignition device which automatically lights the pilot. Do not try to light the

pilot by hand.

• Before operating, smell all around the appliance area for gas and next to the ﬂ oor because some gas is

heavier than air and will settle on the ﬂ oor.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁ ed service technician

to inspect the appliance and replace any part of the control system and any gas control which has been

underwater.

FOR YOUR SAFETY READ BEFORE LIGHTING

WHAT TO DO IF YOU SMELL GAS

LIGHTING INSTRUCTIONS

TO TURN OFF GAS

A. Stop! Read the above safety information on this label.

B. Remove batteries from the transmitter and set thermostat to lowest setting, if

equipped.

C. Turn off all electrical power to the appliance.

D. Open the glass door, if equipped.

E. Turn the manual shut-off valve clockwise to the “OFF” position. (Shut-off valve is

located on the ﬂ ex connector).

F. Wait ﬁ ve (5) minutes to clear out any gas. If you smell gas including near the

ﬂ oor, STOP! Follow the instructions above in the “WHAT TO DO IF YOU

SMELL GAS” section. If you don’t smell gas; close the glass door and go to

the next step.

G. Turn the manual shut-off valve counter clockwise to the “ON” position.

H. Turn on all electrical power to the appliance and re-install the batteries into the

transmitter. Set thermostat to desired setting, if equipped.

I. Turn on the remote wall switch to the appliance.

J. If the appliance will not operate, follow instructions “TO TURN OFF GAS” and

call your service technician or gas supplier.

A. Set thermostat to lowest setting, if equipped.

B. Turn off the remote wall switch to the appliance.

C. Turn off all electric power to the appliance if service is to be performed.

D. Turn manual shutoff valve clockwise to the “OFF” positon. Do not force.

• Turn off all gas to the appliance.

• Open windows.

• Do not try to light any appliance.

• Do not touch any electric switch; do not use

any phone in your building

• Immediately call your gas supplier from a

neighbour’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call

the ﬁ re department.

• If you do not follow these instructions exactly, a ﬁ re or explosion may result causing property damage, personal

injury, or loss of life.

• If applicable, always light the pilot whether for the ﬁ rst time or if the gas supply has run out with the glass door

opened or removed.

add gas knob

add gas valve

Ensure that a continuous gas ﬂ ow is at the burner before installing the door. When lit for the ﬁ rst time, the

appliance will emit an odor for a few hours. This is a normal temporary condition caused by the “burn-in” of

paints and lubricants used in the manufacturing process and will not occur again. After extended periods of

non-operation, such as, following a vacation or warm weather season, the appliance may emit a slight odor for a

few hours. This is caused by dust particules in the heat exchanger burning off. In both cases, open a window to

sufﬁ ciently ventilate the room.

This appliance is equipped with an ignition device which automatically lights the pilot. Do not try to light the

pilot by hand.

note:

MANUAL SHUT-OFF

(SHOWN IN OFF POSITION)

In order to overcome the dense cold air that can build up in the venting system during extreme cold conditions, we recom-

mend turning on and off your appliance on the low ﬂ ame setting and with the split ﬂ ow function for the rear burner turned

off (if equipped). Once the appliance has operated for a minimum of 5 to 10 minutes on low, typically the ﬂ ame can then be

increased to the high setting and the rear burner (split ﬂ ow function) can be turned on (if equipped). This will help to avoid un-

necessary shutdowns while the insert is warming up and trying to overcome the cold air block in the venting system.

4.1 extreme cold lighting instructions

f i r e - p a r t s . c o m

W415-1867 / B / 02.07.19

5.0 remote control layout

5.2 split ﬂ ow (GDIX4 only)

Low battery alarm

Key Lock

Room

Temperature

Light

Flame ON

Blower

Transmission

CPI mode

Split Flow

The split ﬂ ow function controls the ability to turn ON /

OFF a second burner.

1. Use the mode key to guide you to the split

ﬂ ow function.

2. Pressing the up arrow key will activate the

second burner.

3. Pressing the down arrow key will deactivate

the second burner. A single “beep” will

conﬁ rm the reception of the command.

note:

This is no way to modulate the flame heights separately.

°F

OFF

°F

5.3 initializing the transmitter / battery holder for the ﬁ rst time

A. Install the 4 AA batteries into the Proﬂ ame 2 battery holder, note the polarity of the batteries and insert as

indicated on the cover (+/-).

B. Ensure the 3 position slider switch is switched to the “REMOTE” position (middle position).

C. Press the reset/programming button, use a small object such as a paper clip in order to reach the button

marked PRG, as shown in the illustration below.

D. The battery holder will beep 3 times to indicate that it’s ready to synchronize with the transmitter.

E. Install the 3 AAA batteries into the transmitter, as shown in the photograph below, then press the ON

button, The battery holder will beep 4 times to indicate that the transmitter’s command is accepted.

note:

The initializing process must be completed within 10 seconds of pressing the reset/program button (PRG).

(4) AA Batteries

TRANSMITTER

RESET/PROGRAM

BUTTON (PRG)

BATTERY HOLDER

SLIDER SWITCH

5.1 general transmitter layout

f i r e - p a r t s . c o m

W415-1867 / B / 02.07.19

remote control layout

5.4 temperature display

A. With the system in the off position, press the temperature key

and the mode key at the same time to change from degrees F to

B. Look at the LCD screen on the transmitter to verify that a C or F is

visible to the right of the room temperature display.

73 23

°F °C

5.5 ﬂ ame height

5.6 blower speed

If the appliance is equipped with a hot air circulating fan, the speed of

the fan can be controlled by the remote system. The fan speed can be

adjusted through six (6) speeds.

A. Use the mode key to guide you to the fan control icon.

B. Use the up/down arrow keys to turn on/off or adjust the fan

speed. A single “beep” will conﬁ rm reception of the command.

°F

When the desired blower speed is selected, the blower will automatically come on 5 minutes after the main

burner has been turned on and remain on twelve minutes after it has been turned off.

note:

The remote control has six (6) ﬂ ame levels. With the system on and the ﬂ ame level at the maximum, press the

down arrow key once and it will reduce the ﬂ ame height by one step until the ﬂ ame is turned off.

The up arrow key will increase the ﬂ ame height each time it is pressed. If the up arrow key is pressed while

the system is on but the ﬂ ame is off, the ﬂ ame will come on at the high position. A single “beep” will conﬁ rm

reception of the command.

°F

OFF

°F

Flame Off Flame at level 1 Flame at level 5 Flame at “Hi” level 6

ADD

TITLE:

Night

Light

Dimmer

Control

°F

OFF

°F

The auxiliary function controls the Night Light™ with dimmable control.

A. Use the mode key to guide you to the Night Light™ icon.

B. The intensity of the output can be adjusted through 6 levels.

Use the up/down arrow keys to adjust the output level. A single beep

will conﬁ rm reception of the command.

5.7 night light dimmer control

DD TITLE: IN THE EVENT OF A POWER FAILURE

If the receiver is equipped with batteries they will enable ﬂ ame height control or on/off function to control the

appliance during a power failure. Blower and Night Light™ operation is not possible. Refer to “appliance

operation” section when communications between receiver and transmitter have been lost. The receiver will

emit a “beep” sound to conﬁ rm programming has been successful once power is restored. During a power

failure, if the appliance was on, the ﬂ ame height will stay at the setting prior to the failure. If off when the failure

occurs and then turned on, the ﬂ ame height will come on at “Hi”. The ﬂ ame height can then be controlled by the

remote.

5.8 in the event of a power failure

note:

Your new ﬁ replace includes a night light that allows you to enjoy the appearance of your ﬁ replace when the

ﬂ ames are not on.

note:

Please note the night light is not designed to be in used whilst the ﬁ replace is burning. The ﬁ replace, logs, and

ﬂ ame have been designed to produce the most aesthetically appealing look without the need of the night light.

If the night light is used at the same time as the ﬁ replace is burning, the life time of the night light bulb will be

signiﬁ cantly reduced and the need to replace the bulb will become more frequent.

When the desired blower speed is selected, the blower will automatically come on 5 minutes after the main

burner has been turned on and remain on twelve minutes after it has been turned off (thermostat mode only).

f i r e - p a r t s . c o m

W415-1867 / B / 02.07.19

remote control layout

RESET/PROGRAM BUTTON (PRG)

A. The battery holder is located in the valve compartment,

accessible for programming the remote.

B. Install 4 AA batteries, Ensure that the positive and negative

ends correspond with those identified in the battery holder.

C. In the case of a power outage, the 3 position slider switch

needs to be in the “ON” position (up).

note:

Ensure the 3 positions slider switch is in the “REMOTE”

position (middle).

The life span of the remote batteries depends on various factors: quality of the batteries,

the number of ignitions, etc.

When the transmitter batteries are low, a battery icon will appear on the LCD display

before all battery power is lost. When the batteries are replaced, this icon will disappear.

When the receiver batteries are low, no “beep” will be emitted from the receiver when

it receives an on/off command. This in an alert for the receiver that there’s low battery.

When the batteries are replaced the “beep” will be emitted from the receiver when the on/off key is pressed.

If the batteries of the receiver or transmitter are low, the appliance can be turned on manually by sliding the

three position slider switch on the receiver to the on position. This will bypass the remote control feature and the

appliance main burner will come on if the gas valve is in the on position.

°F

5.10 eFIRE Controller application

Napoleon’s eFIRE application will revolutionize the way you use your fireplace! We have cracked the code and

present to you the first fireplace to be controlled by Bluetooth technology, using an intuitive app on your mobile

device.

When fully equipped (if applicable), the eFIRE application allows you to select from a multitude of colours to suit

your mood or décor simply by scrolling through the colour wheel. Additionally, Napoleon’s eFIRE application allows

you to control many other functions of your fireplace, including on/off, flame height, light feature, blower, and a

timer to create a schedule for your fireplace that works for you.

Using the instructions on the eFIRE Controller application website http://napoleon.com/efire, install the

application and enjoy the features the eFIRE Controller application has to offer. *

* Visit the website or contact your authorized dealer for appliance-specific information and/or frequently asked

questions regarding features and products available with the eFIRE Controller application.

note:

The remote control is considered the master control for the appliance and can always be used to turn the

appliance off (ex. the eFIRE Controller application user, in control of the appliance, leaves the home).

5.11 low battery

5.12 battery holder / backup installation

ADD TITLE: CHILD PROOF FUNCTION

This function will lock the keys to avoid unsupervised operation.

A. Press the MODE and UP keys at the same time.

B. To de-activate this function, press the MODE and UP keys at the same time.

°F

5.9 key lock

f i r e - p a r t s . c o m

W415-1867 / B / 02.07.19

clearances around ﬁ replace

WARNING

• Your appliance, gas/electrical connections, venting and various key components are hidden behind the wall. It is

critical that no screws penetrate these components. Failure to follow instructions may cause improper operation,

damage, personal injury or ﬁ re. Always use a stud ﬁ nder and only screw into studs.

6.0 clearances around ﬁ replace

Without making adequate provisions to account for the heat, the temperatures above the ﬁ replace will be hot, making

it unsuitable for mounting a TV or other objects sensitive to heat without risk of damage.

Installing a mantel between this appliance and electronics or other materials that may be sensitive to heat will reduce

the effect of direct heat on them.

The size and material of the mantel will affect the allowable clearance above your ﬁ replace and incorrect placement

could become a ﬁ re hazard. Consult your installation manual and/or authorized dealer for more information before

mounting a mantel, a shelf or any other object above your appliance.

Your ﬁ replace, gas/electrical connections and vent are hidden directly behind the ﬁ nished wall. Great care should be

taken to avoid screwing or nailing into these components. Always use a stud ﬁ nder to determine stud location and

only screw into studs.

Do not screw into the area around the ﬁ replace opening as some of your appliance may be hidden behind the

ﬁ nished wall. Refer to your installation manual and/or contact your local dealer for more information.

Fireplaces

generate radiant

heat. Do not put

objects in front

of the appliance

(minimum

distance of 4 feet

[1.21m]).

The area above a ﬁ replace gets hot.

Combustible objects or materials must

never be placed in this area. For mini-

mum clearances, refer to installation

manual or your authorized dealer.

WARNING

f i r e - p a r t s . c o m

W415-1867 / B / 02.07.19

clearances around ﬁ replace

6” min.

Top of ﬁnishing ﬂange

(ﬁreplace opening)

2.5” min.

2” min. (3” max. recommended)

6” min.

2.5” min.

6” min.

2.5” min.

See “minimum clearance

to mantle” section

(installation manual).

Enclosure

TV bracket

Flush installation with mantel

Partially recessed installation with mantel

Recessed installation with protrusion

Top of ﬁnishing ﬂange

(ﬁreplace opening)

Top of ﬁnishing ﬂange

(ﬁreplace opening)

2” min. (3” max. recommended)

Top of

ﬁnishing

ﬂange

(ﬁreplace

opening)

Enclosure

TV bracket

Flush installation without mantel

Appliance

• These are recommended minimum clearances only and are in supplied in good faith and not a guarantee

of compliance with TV manufacturers’ maximum allowable operating temperatures. Always comply to TV

manufacturers’ requirements.

• TV temperatures must be validated at the time of installation as air ﬂ ow characteristics within the

room can vary and maximum acceptable operating temperatures can vary from appliance to appliance.

TVs cannot be used where the TV temperature exceeds the manufacturer’s maximum allowable operating

temperatures (see TV manufacturer’s speciﬁ cations).

• Mantel height and depth must conform to mantel clearance requirements speciﬁ ed in this manual, see

“minimum clearance to combustible mantel” section in installation manual.

• Dimension “A” the gap between the top of the ﬁ nishing ﬂ ange and the bottom of the TV are taken from the

top of the ﬁ replace opening.

• TV temperatures may be further reduced by increasing the horizontal distance between the front of the TV

and the front edge of the mantel or by increasing dimension “A”. However, increasing the gap between the

top of the mantel and the bottom of the TV beyond the maximum recommended ﬁ gure, typically results in

higher temperatures. Minimum clearance between the mantel and bottom of the TV should be maintained to

allow air circulation below and behind the TV.

note:

f i r e - p a r t s . c o m

W415-1867 / B / 02.07.19

maintenance7.0 maintenance

WARNING

• Turn off the gas and electrical power before servicing the appliance.

• Appliance may be hot. Do not service until appliance has cooled.

For qualiﬁ ed technicians only:

• Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous

operation. Verify proper operation after servicing.

• This appliance and its venting system should be inspected before use and at least annually by a qualiﬁ ed service

person.

• The ﬂ ow of combustion and ventilation air must not be obstructed.

DOS

• Clean your safety barrier or regularly to prevent

the build up of excessive lint/dust from carpeting,

pet hair, etc. Simply vacuum using the brush

attachment.

• Always use ammonia-free glass cleaners.

• Service your appliance annually and/or as

required. Service must be conducted by a qualiﬁ ed

technician.

• Keep your appliance area clear and free of

combustible materials, gasoline, or other ﬂ ammable

vapors and liquids.

• Check to see that the burner ignites completely

on all openings when turned on. A 5 to 10 second

total light-up period is satisfactory. Service as

required.

DON’TS

• Attempt to service the electrical or gas

components. Contact a qualiﬁ ed technician.

• Use excessive force.

• Use abrasive cleaners on glass.

• Paint the pilot assembly.

• Place objects too close to the ﬁ replace opening.

For any questions and/or concerns regarding your appliance, maintenance and service, please contact your

authorized dealer.

note:

f i r e - p a r t s . c o m

W415-1867 / B / 02.07.19

maintenance

This appliance is factory equipped with ceramic glass. Use only replacement parts as supplied by the appliance

manufacturer. DO NOT SUBSTITUTE MATERIALS.

Buff lightly with a clean dry soft cloth to remove accumulated dust or ﬁ ngerprints. Clean both sides of the glass

after the ﬁ rst 10 hours of operation with an ammonia-free glass cleaner.

Thereafter, clean as required. If the glass is not kept clean permanent discoloration and / or blemishes may

result. Contact you local authorized dealer / distributor for complete cleaning instructions.

Razor blades, steel wool, or other metallic objects must not be used on both surfaces of the glass. Doing so

can remove a thin layer of metal from the razor blades, steel wool, or other metallic objects that may then be

deposited onto the coating. This can result in a discoloured stain or scratch-like mark. More importantly, this can

scratch the glass surface, thereby reducing its strength.

Do not operate the appliance with broken glass, as leakage of ﬂ ue gases may result.

Contact your local authorized dealer / distributor for complete cleaning instructions.

If the glass should ever crack or break while the ﬁ re is burning, do not open the door until the ﬁ re is out. Do not

operate the appliance until the glass has been replaced. Contact you local authorized dealer / distributor for

replacement parts. DO NOT SUBSTITUTE MATERIALS.

Vinegar-based glass cleaners have demonstrated an ability to provide a clean, streak free glass surface.

note:

Firebox Glass Door :

Replacement glass/frame assembly shall be replaced as a complete unit as supplied by the appliance

manufacturer.

7.1 care of glass

WARNING

• Do not clean glass when hot! Do not use abrasive cleaners to clean glass.

Do not use ammonia-based cleaners.

7.2 care of plated parts

If the appliance is equipped with plated parts, you must clean ﬁ ngerprints or other marks from the plated surfaces

before operating the appliance for the ﬁ rst time. Use an ammonia-free or vinegar-based cleaner and a towel

to clean. If not cleaned properly before operating for the ﬁ rst time, the marks can cause permanent blemishes

on the plating. After the plating is cured, the ﬁ ngerprints and oils will not affect the ﬁ nish and little maintenance

is required, just wipe clean as needed. Prolonged high temperature burning with the door ajar may cause

discolouration on plated parts.

The protective wrap on plated parts is best removed when the assembly is at room temperature but this can

be improved if the assembly is warmed (i.e. using a hair dryer or similar heat source).

note:

f i r e - p a r t s . c o m

W415-1867 / B / 02.07.19

maintenance

WARNING

• Glass may be hot. Do not touch glass until cooled.

• If equipped with door latches that are part of a safety system, they must be properly engaged. Do not

operate the appliance with latches disengaged.

• Facing and/or ﬁ nishing materials must not interfere with air ﬂ ow through air openings, louvre openings,

operation of louvres, or doors/access for service. Observe all clearances when applying combustible

materials.

• Before door is removed, turn the appliance off and wait until appliance is cool to the touch. Doors are heavy

and fragile so handle with care.

7.3 safety barrier and glass door removal / installation

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with the

appliance and must be installed.

1. Before the glass door can be removed, the safety barrier must be removed. Lift the safety barrier from

the 4 tabs, tilt the top forward, and remove from the appliance (Fig. 1 and 2).

2. Release the top left and right door latches, located at the top of the door (Fig. 3). Tilt forward and lift

from slots.

3. Reverse these steps to re-install the safety barrier and glass door. Ensure safety barrier is installed

correctly.

SAFETY BARRIER

Fig. 1

Fig. 2

note:

If applicable, the optional front must be removed to allow the door to be opened or closed.

Fig. 3

GDIG3 Illustrated

f i r e - p a r t s . c o m

W415-1867 / B / 02.07.19

replacements

8.0 replacement parts

WARNING

• Failure to position the parts in accordance with this manual or failure to use only parts speciﬁ cally approved

with this appliance may result in property damage or personal injury.

Contact your dealer for questions concerning prices and policies on replacement parts. Normally, all parts can

be ordered through your Authorized dealer / distributor.

For warranty replacement parts, a photocopy of the original invoice will be required to honour the

claim.

When ordering replacement parts always give the following information:

• Model & Serial Number of appliance

• Installation date of appliance

• Part number

• Description of part

• Finish

For service parts, see your Installation manual.

f i r e - p a r t s . c o m

W415-1867 / B / 02.07.19

accessories

9.0 accessories for GDI3 / GDIG3/ GDIX3

Items may not appear exactly as illustrated.

Ref. No. Part Number Description

1 SBK3B2540 Small 3-sided backerplate

2 MBK3B2846 Medium 3-sided backerplate

3 LBK3B3048 Large 3-sided backerplate

Ref. No. Part Number Description

LBK4F4B3 ** Large 4-sided faceplate, blac

LCP4F4B3 ** Large 4-sided faceplate, coppe

LGM4F4B3 ** Large 4-sided faceplate, gun metal

LCH4F4B3 ** Large 4-sided faceplate, charcoal

SGM4F3B3 * Small 4-sided faceplate, gun metal

SCH4F3B3 * Small 4-sided faceplate, charcoal

SBK4F4B3 ** Small 4-sided faceplate, black

SCP4F4B3 ** Small 4-sided faceplate, coppe

SGM4F4B3 ** Small 4-sided faceplate, gun metal

SCH4F4B3 ** Small 4-sided faceplate, charcoal

Stocked

SBK3B2540 MBK3B2846 LBK3B3048

SBK3F3B3*

SCP3F3B3*

SGM3F3B3*

SCH3F3B3*

LBK3F3B3*

LCP3F3B3*

LGM3F3B3*

LCH3F3B3*

BK4B3142

SBK4F3B3*

SCP4F3B3*

SGM4F3B3*

SCH4F3B3*

SBK4F4B3**

SCP4F4B3**

SGM4F4B3**

SCH4F4B3**

LBK4F4B3**

LCP4F4B3**

LGM4F4B3**

LCH4F4B3**

SABK4F3B3*

SACP4F3B3*

SAGM4F3B3*

SACH4F3B3*

BK4B3142

SBK4F3B3 *

SCP4F3B3 *

SABK4F3B3 *

SACP4F3B3 *

SAGM4F3B3 *

SACH4F3B3 *

Small arched 4-sided faceplate, blac

Small arched 4-sided faceplate, coppe

Small arched 4-sided faceplate, gun metal

Small arched 4-sided faceplate, charcoal

Large 4-sided backerplate

Small, 4-sided faceplate, blac

Small, 4-sided faceplate, coppe

SBK3F3B3 *

3-sided faceplate, black

SCP3F3B3 * 3-sided faceplate, coppe

SCH3F3B3 *

Small, 3-sided faceplate, charcoal

LBK3F3B3 * Large 3-sided faceplate, blac

LCP3F3B3 * Large 3-sided faceplate, coppe

LGM3F3B3 * Large 3-sided faceplate, gun metal

SGM3F3B3 * Small 3-sided faceplate, gun metal

LCH3F3B3 * Large 3-sided faceplate, charcoal

* For use with 3-sided backerplate (see SBK3B2540, MBK3B2846, or LBK3B3048).

** For use with 4-sided backerplate (see BK4B3142).

Stocked

f i r e - p a r t s . c o m

La page charge ...

NAPOLEON BK4B3142 Le manuel du propriétaire

Marque: NAPOLEON

Modèle: BK4B3142

Catégorie: Cheminées

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: NAPOLEON BK4B3142 Owner's manual

NAPOLEON BK4B3142 Le manuel du propriétaire

NAPOLEON BK4B3142 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents