Magtek DynaFlex Family Quick Installation Guide

Marque: Magtek

Modèle: DynaFlex Family

Taper: Quick Installation Guide

Ce manuel convient également à

DynaFlex Kiosk Family

Environmental Notice:

Storage tempertature

14° to 140°F (-10°C to 60°C)

Operating temperature

32°F to 113°F (0°C to 45°C)

Models

PN Description Display Connection(s)

21078007 DYNAFLEX, PCI, NO DISPLAY, BLACK, USB None USB-C

21078008 DYNAFLEX, PCI, NO DISPLAY, BLACK, BLUE-

TOOTH LE

None USB-C

Bluetooth LE

21078009 DYNAFLEX PRO, PCI, TOUCHSCREEN DISPLAY,

BLACK, USB

Touchscreen USB-C

21078010 DYNAFLEX PRO, PCI, TOUCHSCREEN DISPLAY,

BLACK, BLUETOOTH LE

Touchscreen USB-C

Bluetooth LE

21078011 DYNAFLEX PRO, PCI, TOUCHSCREEN DISPLAY,

BLACK, 802.11 WIRELESS

Touchscreen USB-C

802.11 Wireless

21078012 DYNAFLEX PRO, PCI, TOUCHSCREEN DISPLAY,

BLACK, ETHERNET

Touchscreen USB-C

Ethernet

Mounting / Stability

DynaFlex devices can be used in countertop (traditional brick and mortar),

mounted (to a touchscreen, holster, or other solution), or handheld solutions

(brought to the table with wireless models only). Each device has three (3)

non-slip grip feet for better stability for countertop solutions.

How to Connect to USB Host

Devices connect to a host via the USB-C plug located on the bottom of the

device. For best results, use the cable that is included with the device, it includes

shielding at both ends of the cable to reduce emissions and interference.

Compatible with USB Hosts: Windows 10, Android 4.4.2 and above.

Commands

Devices are designed to connect to a host which sends commands and data

back and forth. In any solution, DynaFlex or DynaFlex Pro must be connected

to a host with software installed that knows how to communicate with the

device and is capable of processing transactions. Follow the installation

and conguration instructions provided by the vendor of the host or the host

software for use. For development of applications, see the SDKs and APIs

on www.magtek.com under support.

Power

• To power on the device, connect it to a USB host. Upon connecting to

a Windows 10 host, the display and LEDs turn on briey, then turn

off when Windows suspends the device’s USB connection to conserve

power. To turn the display and LEDs back on, connect to the device

using software on the host (for example, by using the Open Device

button in 1000007406 DynaFlex, DynaProx Test Utility, available from

MagTek), which signals Windows to resume the USB connection and

provide full power to the device.

• To power off the device, disconnect it from the USB host.

Color Touchscreen

DynaFlex Pro’s color touchscreen can display a logo or custom messaging

and depicts on-screen instructions for insert, tap, or swipe operations. The

screen is inset and measures 2.27in. (57.60mm) X 1.70 in. (43.20mm),

320x240 RGB.

Overview

DynaFlex and DynaFlex Pro are ready to launch your payment environment

to the next level. All DynaFlex products offer an integrated secure card

reader authenticator for magnetic stripe cards, EMV chip cards (contact and

contactless), and NFC enabled mobile wallets including Samsung Pay

Google Pay

, and Apple Pay

. DynaFlex Pro offers a color, touchscreen

display for added convenience. DynaFlex products are made from molded

rubberized black plastic with matching black lens on the face. Custom colors

and silkscreened logos are available with a minimum order size.

Major Components

DynaFlex and DynaFlex Pro

Secure Card Reader Authenticator

Quick Installation Guide

Setup and Installation

MagTek

Inc., 1710 Apollo Court, Seal Beach CA 90740 | p 562-546-6400 | support 651-415-6800 | f 562-546-6301 | www.magtek.com

DynaFlex and DynaFlex Pro Major Components

(Touchscreen applies to DynaFlex Pro models only)

Top Face

DynaFlex and DynaFlex Pro Major Components

Underside

Compliance

FCC INFORMATION

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modications not expressly approved by MagTek could void the user’s authority to operate this equipment.

CANADIAN DECLARATION OF CONFORMITY

This digital apparatus does not exceed the Class B limits for radio noise from digital apparatus set out in the Radio Interference Regulations of the

Canadian Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe B

prescrites dans le Réglement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conformé à la norme NMB-003 du Canada.

INNOVATION, SCIENCE AND ECONOMIC DEVELOPEMENT CANADA (ISED)

This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not

cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux

deux conditions suivantes: (1) L’appareil ne doit pas produire de brouillage, et (2) L’utilisateur de l’appareil doit accepter tout brouillage radioélectrique

subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

CE STANDARDS

Testing for compliance with CE requirements was performed by an independent laboratory. The unit under test was found compliant with standards

established for Class B devices.

EU STATEMENT

Hereby, MagTek Inc. declares that the radio equipment types Wideband Transmission System (802.11 wireless and Bluetooth Low Energy), and Non-

Specic Short Range Device (contactless) are in compliance with Directive 2014/53/EU. The full text of the EU declarations of conformity is available

at the following internet addresses:

• https://www.magtek.com/Content/DocumentationFiles/D998200404.pdf for DynaFlex with no display, USB connection

• https://www.magtek.com/Content/DocumentationFiles/D998200410.pdf for DynaFlex with no display, Bluetooth LE connection

• https://www.magtek.com/Content/DocumentationFiles/D998200411.pdf for DynaFlex Pro with USB connection

• https://www.magtek.com/Content/DocumentationFiles/D998200412.pdf for DynaFlex Pro with Bluetooth LE connection

• https://www.magtek.com/Content/DocumentationFiles/D998200413.pdf for DynaFlex Pro with 802.11 wireless connection

AUSTRALIA / NEW ZEALAND STATEMENT

Testing for compliance with AS/NZS standards was performed by a registered and accredited laboratory. The unit under test was found compliant

with standards established under AS/NZS CISPR 32 (2013), AS/NZS 4268 Table 1, Row 59 DTS 2400-2483MHz SRD (802.11), and AS/NZS 4268

(2017) Table 1, Row 43 13.553-13.567MHz (contactless reader).

UL/CSA

This product is recognized per UL 60950 1, 2nd Edition, 2011 12 19 (Information Technology Equipment - Safety - Part 1: General Requirements), CSA

C22.2 No. 60950 1 07, 2nd Edition, 2011 12 (Information Technology Equipment - Safety - Part 1: General Requirements).

ROHS STATEMENT

When ordered as RoHS compliant, this product meets the Electrical and Electronic Equipment (EEE) Reduction of Hazardous Substances (RoHS)

European Directive 2002/95/EC. The marking is clearly recognizable, either as written words like “Pb-free,” “lead-free,” or as another clear symbol ( ).

PCI STATEMENT

PCI Security Standards Council, LLC (“PCI SSC”) has approved this PIN Transaction Security Device to be in compliance with PCI SSC’s PIN Security

Requirements.

When granted, PCI SSC approval is provided by PCI SSC to ensure certain security and operational characteristics important to the achievement of

PCI SSC’s goals, but PCI SSC approval does not under any circumstances include any endorsement or warranty regarding the functionality, quality

or performance of any particular product or service. PCI SSC does not warrant any products or services provided by third parties. PCI SSC approval

does not under any circumstances include or imply any product warranties from PCI SSC, including, without limitation, any implied warranties of

merchantability, tness for purpose, or non-infringement, all of which are expressly disclaimed by PCI SSC. All rights and remedies regarding products

and services which have received PCI SSC approval shall be provided by the party providing such products or services, and not by PCI SSC.

Accepting Payments

How to Swipe Magnetic Stripe Cards

Locate the swipe path on the face of the device. Orient the card with the

magnetic stripe facing away from the cardholder and the touchscreen or

contactless landing zone, toward the LEDs and the chip card insertion slot.

Swipe the card through the magnetic stripe reader in either direction.

How to Insert EMV Contact Chip Cards

Locate the insertion slot on the face of the device. Orient the chip card

so the chip faces the cardholder, toward the touchscreen or contactless

landing zone and the LEDs. Insert the chip card into the slot, then push

gently on the card until it stops. There should not be any substantial

resistance until the chip card is fully inserted. Remove the card when

prompted.

How to Tap Contactless Cards / Devices

The device lights the rst LED green to indicate it is ready for a tap. Tap

the card or electronic payment device on the contactless landing zone,

indicated by the EMVCo Contactless Indicator on the device’s face. The card

or device’s antenna* must be centered over the contactless landing zone.

The 4 LEDs will light up green and the device may beep (some host software

indicators are up to the implementer) and on the touchscreen it shows

REMOVE CARD then THANK YOU. Remove the card or electronic payment

device from the contactless landing zone.

*NOTE ON ELECTRONIC DEVICES: If the cardholder is using an electronic

payment device, such as a smartphone, make sure the payment device

has NFC turned ON and has a payment app congured to process

transactions. Because each smartphone model may have its NFC antenna

placed differently, the ideal tap position may vary by make and model. For

example, Samsung users may need to center the phone on the contactless

landing zone, while Apple users may need to tap the top of the phone on the

contactless landing zone.

LEDs

DynaFlex and DynaFlex Pro have 4 LEDs that provide response to the user

for Power, Connection, Device Status, and Card Status. The Installation and

Operation Manual has a more complete list of light signals.

Please note that the use of this accessory with an Apple product may affect wireless performance. Apple®, Apple Pay®, OS X®, iPhone®, iPad®, iPad Air®, iPad Pro®, Lightning®, and Mac® are trademarks of Apple Inc., registered in the U.S. and other countries.

EMV® is a registered trademark in the U.S. and other countries and an unregistered trademark elsewhere. The EMV trademark is owned by EMVCo, LLC. The Contactless Indicator mark, consisting of four graduating arcs, is a trademark owned by and used with

permission of EMVCo, LLC.

MagTek

Inc., 1710 Apollo Court, Seal Beach CA 90740 | p 562-546-6400 | support 651-415-6800 | f 562-546-6301 | www.magtek.com

Use and Compliance

Swiping Magstripe Card EMV Chip Card Insertion

NFC Contactless Device Tap EMV Contactless Card Tap

DynaFlex NFC Contactless Landing Zone

DynaFlex Pro

DynaFlex

DynaFlex and DynaFlex Pro - Secure Card Reader Authenticator