Schumacher TY26877 John Deere Four Independent Station Battery Charger JD-406A Le manuel du propriétaire

Marque: Schumacher

Modèle: TY26877 John Deere Four Independent Station Battery Charger JD-406A

Catégorie: Chargeurs de batterie de voiture

Taper: Le manuel du propriétaire

John Deere

Four Bank Charger

TY26877

OPERATOR’S MANUAL

John Deere Four Bank Charger

OMTY26877 ISSUE 08APR11 (ENGLISH / FRENCH)

CALIFORNIA

Proposition 65 Warning

Diesel engine exhaust and some of its constituents

are known to the State of California to cause cancer,

birth defects, and other reproductive harm.

If this product contains a gasoline engine:

WARNING

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects or other reproductive harm.

The State of California requires the above two warnings.

Additional Proposition 65 Warnings can be found in this manual.

John Deere Merchandise Division

LITHO IN USA

DCYOMTY26877

0099001165-00

John Deere

Four Bank Charger

TY26877

OPERATOR’S MANUAL

John Deere Four Bank Charger

OMTY26877 ISSUE 08APR11 (ENGLISH)

CALIFORNIA

Proposition 65 Warning

Diesel engine exhaust and some of its constituents

are known to the State of California to cause cancer,

birth defects, and other reproductive harm.

If this product contains a gasoline engine:

WARNING

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects or other reproductive harm.

The State of California requires the above two warnings.

Additional Proposition 65 Warnings can be found in this manual.

John Deere Merchandise Division

LITHO IN USA

Introduction

OURGP11,00000C0 1926JAN111/1

Foreword

TYB6030 —UN—08FEB11

TY26877 Battery Charger

THANK YOU for purchasing a John Deere product.

READ THIS MANUAL carefully to learn how to operate

and service your battery charger. Failure to do so could

result in personal injury or equipment damage. This

manual and safety signs on your battery charger may also

be available in other languages. (See your John Deere

dealer to order.)

THIS MANUAL SHOULD BE CONSIDERED a permanent

part of your battery charger and should remain with the

charger when you sell it.

MEASUREMENTS in this manual are given in both metric

and customary U.S. unit equivalents. Use only correct

replacement parts and fasteners.

WRITE PRODUCT INFORMATION in the Specification

section. Accurately record all the numbers to help in

tracing the battery chargermaintainer should it be stolen.

Your distributor also needs these numbers when you

order parts. File the product information in a secure place.

WARRANTY is provided as part of John Deere’s support

program for customers who operate and maintain their

equipment as described in this manual. The warranty

is explained in the Warranty section at the end of this

manual.

This warranty provides you the assurance that John

Deere will back its products where defects appear within

the warranty period. In some circumstances, John Deere

also provides field improvements, often without charge

to the customer, even if the product is out of warranty.

Should the equipment be abused, or modified to change

its performance beyond the original factory specifications,

the warranty will become void and field improvements

may be denied.

051111

PN=2

Contents

Page

Safety........................................................ 05 1

Preparing to Charge

Preparing Battery..............................................10 1

Positioning Battery Charger..............................10 1

Calculating Charge Time..................................10 1

Operation

General Information and Control Panel............15 1

Charging Battery Installed in Vehicle................15 2

Charging Battery Outside of Vehicle.................15 3

Maintenance and Troubleshooting

Maintenance.....................................................20 1

Troubleshooting................................................20 1

Storage

Storing Battery Charger....................................25 1

Specifications

Battery Charger Specifications.........................30 1

Record Product Information..............................30 1

Warranty

Warranty ...........................................................35 1

Original Instructions. All information, illustrations and specifications in this

manual are based on the latest information available at the time of publication.

The right is reserved to make changes at any time without notice.

DEERE & COMPANY

Moline, Illinois

A John Deere ILLUSTRUCTION ® Manual

051111

PN=1

Contents

051111

PN=2

Safety

DX,ALERT 1929SEP981/1

DX,SIGNAL 1903MAR931/1

DX,READ 1916JUN091/1

Recognize Safety Information

This is a safetyalert symbol. When you see this symbol

on your machine or in this manual, be alert to the potential

for personal injury.

Follow recommended precautions and safe operating

practices.

T81389 —UN—07DEC88

Understand Signal Words

A signal word—DANGER, WARNING, or CAUTION—is

used with the safetyalert symbol. DANGER identifies the

most serious hazards.

DANGER or WARNING safety signs are located near

specific hazards. General precautions are listed on

CAUTION safety signs. CAUTION also calls attention to

safety messages in this manual.

TS187 —19—30SEP88

Follow Safety Instructions

Carefully read all safety messages in this manual and on

your machine safety signs. Keep safety signs in good

condition. Replace missing or damaged safety signs. Be

sure new equipment components and repair parts include

the current safety signs. Replacement safety signs are

available from your John Deere dealer.

There can be additional safety information contained on

parts and components sourced from suppliers that is not

reproduced in this operator’s manual.

Learn how to operate the machine and how to use controls

properly. Do not let anyone operate without instruction.

Keep your machine in proper working condition.

Unauthorized modifications to the machine may impair the

function and/or safety and affect machine life.

TS201 —UN—23AUG88

If you do not understand any part of this manual and need

assistance, contact your John Deere dealer.

051

051111

PN=5

Safety

DX,SPARKS 1903MAR931/1

DX,POISON 1921APR931/1

Prevent Battery Explosions

Keep sparks, lighted matches, and open flame away from

the top of battery. Battery gas can explode.

Never check battery charge by placing a metal object

across the posts. Use a voltmeter or hydrometer.

Do not charge a frozen battery; it may explode. Warm

battery to 16°C (60°F).

TS204 —UN—23AUG88

Prevent Acid Burns

Sulfuric acid in battery electrolyte is poisonous. It is strong

enough to burn skin, eat holes in clothing, and cause

blindness if splashed into eyes.

Avoid the hazard by:

1. Filling batteries in a wellventilated area.

2. Wearing eye protection and rubber gloves.

3. Avoiding breathing fumes when electrolyte is added.

4. Avoiding spilling or dripping electrolyte.

5. Use proper jump start procedure.

If you spill acid on yourself:

1. Flush your skin with water.

2. Apply baking soda or lime to help neutralize the acid.

3. Flush your eyes with water for 15—30 minutes. Get

medical attention immediately.

If acid is swallowed:

1. Do not induce vomiting.

2. Drink large amounts of water or milk, but do not

exceed 2 L (2 quarts).

3. Get medical attention immediately.

TS203 —UN—23AUG88

052

051111

PN=6

Safety

DX,WEAR2 1903MAR931/1

DX,MSDS,NA 1903MAR931/1

DX,DRAIN 1903MAR931/1

Wear Protective Clothing

Wear close fitting clothing and safety equipment

appropriate to the job.

Operating equipment safely requires the full attention of

the operator. Do not wear radio or music headphones

while operating machine.

TS206 —UN—23AUG88

Handle Chemical Products Safely

Direct exposure to hazardous chemicals can cause

serious injury. Potentially hazardous chemicals used with

John Deere equipment include such items as lubricants,

coolants, paints, and adhesives.

A Material Safety Data Sheet (MSDS) provides specific

details on chemical products: physical and health hazards,

safety procedures, and emergency response techniques.

Check the MSDS before you start any job using a

hazardous chemical. That way you will know exactly what

the risks are and how to do the job safely. Then follow

procedures and recommended equipment.

(See your John Deere dealer for MSDS’s on chemical

products used with John Deere equipment.)

TS1132 —UN—26NOV90

Dispose of Waste Properly

Improperly disposing of waste can threaten the

environment and ecology. Potentially harmful waste used

with John Deere equipment include such items as oil, fuel,

coolant, brake fluid, filters, and batteries.

Use leakproof containers when draining fluids. Do not use

food or beverage containers that may mislead someone

into drinking from them.

Do not pour waste onto the ground, down a drain, or into

any water source.

Air conditioning refrigerants escaping into the air can

damage the Earth’s atmosphere. Government regulations

may require a certified air conditioning service center to

recover and recycle used air conditioning refrigerants.

Inquire on the proper way to recycle or dispose of waste

from your local environmental or recycling center, or from

your John Deere dealer.

TS1133 —UN—26NOV90

053

051111

PN=7

Safety

OUOD006,00002EC 1903JUN041/1

IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS

CAUTION: RISK OF EXPLOSIVE GASES.

Working in the vicinity of leadacid batteries

is dangerous. Batteries generate explosive

gases during normal battery operation. Read

this manual and follow the instructions exactly

EACH TIME you use this battery charger.

To reduce risk of battery explosion, follow these

instructions and the instructions published by

battery manufacturer. Review the cautionary

markings on the battery, battery charger,

and engine compartment.

WARNING: Battery posts, terminals, and related

accessories contain lead and lead compounds, chemicals

known by the State of California to cause cancer and

reproductive harm. Wash hands after handling.

1. SAVE THESE INSTRUCTIONS. This manual contains

important safety and operating instructions for your

battery charger. Read and understand this manual

before using the battery charger.

2. To reduce risk of electric shock, do not operate battery

charger when unit is exposed to water. Do not expose

battery charger to rain or snow.

3. Use of an attachment not recommended or sold by the

battery charger manufacturer may result in a risk of

fire, electric shock or injury to persons.

4. To reduce the risk of damage to electric plug and

cord, pull by plug rather than cord when disconnecting

battery charger.

5. Use of an extension cord is not recommended. Use

of an improper extension cord could result in fire or

electric shock. If an extension cord must be used,

make sure:

a. the pins on plug of extension cord are the same

number, size, and shape as those on plug of

charger,

b. the extension cord is properly wired and in good

electrical condition, and

c. the wire size is large enough for the length of cord

for the ampere rating of this battery charger as

specified below.

Length of Cord (Ft.)

25 50 100 150

AWG Size of Cord

18 18 18 16

6. Never alter AC cord or grounding plug provided. If

temporary adapter must be used to plug battery

charger into a two pole outlet, connect the grounding

hardware on the adapter to a properly grounded outlet

using the center screw of the outlet plate. Be sure the

center screw of the outlet plate is grounded. Use of

adapter plug NOT ALLOWED in Canada.

7. Locate battery power cord so it cannot be stepped on,

tripped over, or subjected to damage or stress. Do not

operate battery charger with damaged cord or plug.

Replace cord or plug immediately.

8. Do not operate battery charger if it has received a

sharp blow, been dropped, or otherwise damaged in

any way. Take it to a qualified service technician.

9. Do not disassemble battery charger. Take charger to a

qualified service technician when service or repair is

necessary. Incorrect assembly may result in electric

shock or fire.

10. To reduce risk of electric shock, unplug battery charger

from outlet before attempting any maintenance or

cleaning.

054

051111

PN=8

Safety

OURGP12,000010C 1902JUN041/1

OUOD006,000002EE 1905OCT061/1

Personal Precautions

1. Wear complete eye protection and clothing protection.

Avoid touching eyes when working near batteries.

2. Have plenty of fresh water and soap nearby, in case

battery acid contacts skin, clothing, or eyes.

3. Someone should be within range of your voice or

close enough to come to your aid when you work near

a leadacid battery.

4. Avoid touching eyes while working with battery. If acid

enters eye, immediately flood eye with running cold

water for 15—30 minutes and get medical attention

immediately. If battery acid contacts skin or clothing,

wash immediately with soap and water.

5. Batteries generate explosive gases! NEVER smoke

or allow a spark or flame in the vicinity of battery or

engine. Always operate battery charger in an open,

well ventilated area.

6. Do not drop a metal tool onto the battery. It might

spark or shortcircuit the battery or other electrical part

that may cause an explosion.

7. Remove personal metal items such as rings, bracelets,

necklaces, and watches when working near a

leadacid battery.

8. Use the battery charger for charging LEADACID

batteries only. The charger is not intended to supply

power to a low voltage electrical system other

than in a startermotor application. Do not use the

battery charger for charging drycell batteries that

are commonly used with home appliances. These

batteries may burst and cause injury to persons or

damage to property.

9. NEVER charge a frozen battery.

10. NEVER overcharge a battery.

11. Never allow battery acid to drip on charger when

reading specific gravity or filling battery.

12. Never set battery on top of battery charger.

13. Neutralize acid spills thoroughly with baking soda

before attempting to clean up.

Battery Charger Connection Precautions

CAUTION: Connect and disconnect DC clamps

only after removing AC cord from electrical outlet.

Never allow battery charger clamps to

touch each other.

Do not connect both battery charger clamps

directly to the battery.

1. Locate battery charger as far from battery as cables

permit.

2. When connecting battery charger, attach one clamp

to battery and the other clamp to a grounding point

away from the battery.

3. Read the Operation section before connecting the

battery charger.

4. When connecting each clamp, rock or twist the

clamp back and forth several times to make a good

connection. Do not twist or rock the first clamp after

the second clamp has been connected.

5. Never crank engine with charger attached to battery

and 120 volt line.

055

051111

PN=9

Safety

OURGP11,00000E7 1901MAR111/1

Safety Sign

NOTE: English (A) and French (B) safety decals are

located on back of battery charger.

A—English Safety Decal B—French Safety Decal

TYB6041 —UN—08FEB11

Safety Decal English

056

051111

PN=10

Preparing to Charge

OURGP11,00000C1 1929MAR111/1

OURGP11,00000F0 1929MAR111/1

OURGP11,00000C2 1929MAR111/1

Preparing Battery

CAUTION: A marine (boat) battery must be

removed and charged on shore. To charge

it onboard requires equipment specially

designed for marine use.

NOTE: Most starter, deep cycle, and gel type batteries

can be charged with this battery charger.

1. Make sure battery is a 6/12 volt leadacid battery. Do

not use for parallel charging. Charger is designed to

charge/maintain four 6/12 volt batteries.

2. Make sure all vehicle accessories are off.

3. If battery must be removed from vehicle to charge,

always remove grounded terminal from battery first.

4. Make sure area around battery is well ventilated.

Gases can be forcefully blown away using a piece of

cardboard or other nonmetallic material as a fan.

5. Study battery manufacturer’s specific precautions,

such as removing or not removing cell caps while

charging, and recommended rates of charge.

6. For batteries with removable vent caps, add distilled

water to each cell until battery acid reaches level

specified by battery manufacturer. Do not overfill.

7. Clean battery terminals.

Positioning Battery Charger

CAUTION: Risk of explosion. Battery gases

produced during charging can explode. Ventilate

area. Keep sparks and flames away.

1. Never place the battery charger directly above battery

being charged. Gases from battery will corrode and

damage charger.

2. Never allow battery acid to drip on battery charger

when reading gravity or filling battery.

3. Do not operate battery charger in a closed area, or

restrict ventilation in any way.

4. Do not set battery on top of battery charger or battery

charger on top of battery.

5. Position battery charger at least 46 cm (18 inches)

above floor.

TS204 —UN—23AUG88

Risk of Battery Explosion

Calculating Charge Time

Use the following table to more accurately determine the

time it will take to bring a battery to full charge. First,

identify where your battery fits into the chart.

Find your battery’s rating on the table below, and note

the charge time given for each charger setting. The

times given are for batteries with a 50% charge prior

to recharging. Add more time for severely discharged

batteries.

CHARGE RATE

/CHARGING

TIME

BATTERY SIZE/RATING

6 AMP

6  12 AH

38 min  11/4

hrs

Small Batteries

Motorcycle,

garden tractor,

etc.

12  32 AH

11/4  31/2 hrs

200  315 CCA 40  60 RC 33/4  43/4 hrs

315  550 CCA 60  85 RC 43/4  6 hrs

Cars/Trucks

550  1000 CCA 80  190 RC 6  111/2 hrs

80 RC

6 hrs

140 RC

9 hrs

160 RC

10 hrs

Marine/Deep Cycle

180 RC

11 hrs

101

051111

PN=11

Operation

OURGP11,00000C4 1908FEB111/2

OURGP11,00000C4 1908FEB112/2

General Information and Control Panel

Illuminated ON/OFF Power Switch (A): This switch will

turn the battery charger ON or OFF. When power is on,

switch will illuminate red.

Battery type button (B): When button is pressed, 12V or

6V will illuminate.

A—ON/OFF Power Switch B—Battery Type Switch

TYB6039 —UN—08FEB11

Control Panel

LED Indicator

Color of Indicator

Description

(A) Connected LED

Red When lit, battery is

properly connected.

(B) Charging LED

Yellow When lit, battery is

charging.

When lit, battery has

reached full charge

and has gone to

maintain mode.

(D) Check Battery

Red When lit, there is

a problem with the

battery.

NOTE: Charger has an electronic control circuit which

prevents overcharging the battery.

Charging Modes

Battery Connection Indicator: If the charger does not

detect a properly connected battery, the CONNECTED

(red) LED will not light until such a battery is detected.

Charging will not begin until the CONNECTED (red) LED

is on. When charging begins, the CHARGING (yellow)

LED will illuminate.

Charging Mode: When an Automatic Charge is

performed, the charger switches to the Maintain Mode

(see below) automatically after the battery is charged.

Aborted Charge: If charging can not be completed

normally, charging will abort. When charging aborts, the

charger’s output is shut off, and the CHECK BATTERY

(red) LED will blink. To reset after an aborted charge,

disconnect the battery.

Desulfation Mode: If the battery is left discharged for an

extended period of time, it could become sulfated and

not accept a normal charge. If the charger detects a

TYB6040 —UN—08FEB11

sulfated battery, the charger will switch to a special mode

of operation designed for such batteries. If successful,

normal charging will resume after the battery is desulfated.

Desulfation could take up to 10 hours. If desulfation fails,

charging will abort and the CHECK BATTERY (red) LED

will blink, have the battery checked.

Completion of Charge: Charge completion is indicated

by the CHARGED (green) LED. When lit, the charger has

stopped charging and switched to the Maintain Mode of

operation.

Maintain Mode: When the CHARGED (green) LED is lit,

the charger has started Maintain Mode. In this mode, the

charger keeps the battery fully charged by delivering a

small current when necessary.

Fan: The charger is designed to control its cooling fan for

efficient operation. Consequentially, it is normal for the fan

to start and stop when maintaining a fully charged battery.

Keep the area near the charger clear of obstructions to

allow the fan to operate efficiently.

151

051111

PN=12

Operation

OURGP11,00000C5 1930MAR111/1

Charging Battery Installed in Vehicle

CAUTION: A marine (boat) battery must be

removed and charged on shore. To charge

it onboard requires equipment specially

designed for marine use.

Stay clear of fan blades, belts, pulleys, and

other parts that can cause injury.

Battery gases produced during charging can

explode. Keep sparks and flames away.

WARNING: Battery posts, terminals, and related

accessories contain lead and lead compounds, chemicals

known by the State of California to cause cancer and

reproductive harm. Wash hands after handling.

IMPORTANT: DO NOT plug battery charger into power

receptacle or set any charger controls until

ALL connections have been made.

Turn all vehicle switches OFF (ignition, lights,

radio, etc.) before connecting battery charger.

1. Position AC and DC cords to reduce risk of damage

by hood, door, or moving engine parts.

2. Determine which battery terminal is the POSITIVE

terminal. (The Positive terminal may be identified with

a POS, P, or +, and usually has a larger diameter than

the Negative terminal (NEG, N, —).

3. Determine which battery terminal is grounded

(connected) to the chassis.

4. Install one clip of the battery charger to the

UNGROUNDED battery terminal using (a) or (b)

below:

a. NegativeGrounded Vehicles: Connect Positive

(red) clip (A) of battery charger to Positive

(Ungrounded) battery terminal.

TYB6042 —UN—08FEB11

Battery Attaching Clips

A—Positive (+) Clip B—Negative (—) Clip

b. PositiveGrounded Vehicles: Connect Negative

(black) clip (B) of battery charger to Negative

(Ungrounded) battery terminal.

IMPORTANT: Do not connect ground clip to the

carburetor, fuel lines, or sheet metal body parts.

5. Connect remaining battery charger clip to a

heavygauge metal part of vehicle chassis or engine

block, as far from battery as possible.

6. Plug battery charger AC power cord into 120 volt AC

receptacle and turn switch ON.

7. Observe lights on battery charger to determine status.

(See General Information and Controls in this section.)

8. To disconnect battery charger:

a. Turn switch OFF and disconnect AC cord.

b. Remove clip from the vehicle chassis or engine

block.

c. Remove clip from the battery terminal.

152

051111

PN=13

Operation

OURGP11,00000C6 1904APR111/1

Charging Battery Outside of Vehicle

CAUTION: A marine (boat) battery must be

removed and charged on shore. To charge

it onboard requires equipment specially

designed for marine use.

Risk of explosion. Battery gases produced

during charging can explode. Keep sparks

and flames away.

IMPORTANT: DO NOT turn switch ON or set any

charger controls until ALL connections

have been made.

1. Determine which battery terminal is the POSITIVE

terminal. (The Positive terminal may be identified with

a POS, P, or +, and usually has a larger diameter than

the Negative terminal NEG, N, —).

2. Connect Positive (red) clip of battery charger to

Positive (+) terminal of battery.

CAUTION: Risk of explosion. Keep a safe

distance from the battery. DO NOT face battery

when making final connection.

3. Attach at least a 610 mm (24 in.) long 6 gauge (AWG)

insulated battery cable to the Negative (—) battery

post.

4. Stand as far from battery as possible, face away from

battery, and connect Negative (black) clip to free end

of previously installed battery cable.

TYB6042 —UN—08FEB11

Battery Attaching Clips

A—Positive (+) Clip B—Negative (—) Clip

5. Plug battery charger AC power cord into 120 volt AC

receptacle and turn switch ON.

6. Observe lights on battery charger to determine status.

(See General Information and Controls in this section.)

7. To disconnect battery charger:

a. Turn switch OFF and disconnect AC cord.

b. Remove Negative (—) clip from battery cable.

c. Remove battery cable from Negative (—) battery

post.

d. Remove Positive (+) clip from the battery terminal.

153

051111

PN=14

Maintenance and Troubleshooting

OURGP11,00000D1 1929MAR111/1

OURGP11,00000F2 1930MAR111/1

Maintenance

After use and before performing maintenance, unplug and

disconnect the battery charger.

Use a dry cloth to wipe all battery corrosion and other dirt

or oil from the terminals, cords, and the charger case.

Ensure that all of the charger components are in place

and in good working condition, including the plastic boots

on the battery clips.

Servicing does not require opening the unit, as there are

no userserviceable parts.

Troubleshooting

Symptom Problem Solution

CONNECTED (red) LED is not lit.

The battery is not connected correctly.

Check for a poor connection to the

battery and frame. Make sure the

connection points are clean. Rock

the clips back and forth for a better

connection.

Reverse connections at battery.

Shut the charger off and correct the

lead connections.

The CHECK BATTERY (red) LED is

blinking.

The charger is in Abort Mode. Reset the charger by disconnecting

the battery.

Check the battery.

The CHARGED (green) LED turns

on a few minutes or less after

connecting the battery.

The battery may be fully charged or

recently charged, leaving the battery

voltage high enough to appear to be

fully charged.

If the battery is in a vehicle, turn the

headlights on for a few minutes to

reduce the battery voltage and try

charging again.

The battery may be sulfated. A sulfated battery will eventually

accept a charge. Continue charging

for a few hours. If the charger cannot

complete charging the battery, it will

go into Abort Mode.

The charger is making an audible

clicking sound.

The charger has a relay that turns the

current on and off to the battery.

No problem, this is a normal condition.

Charger will not turn on when

properly connected.

AC outlet is dead. Check for open fuse or circuit breaker

supplying AC outlet.

Poor electrical connection.

Check power cord and extension cord

for loose fitting plug.

Battery clips do not spark when

touched together.

The charger is equipped with an

autostart feature. It will not supply

current to the battery clips until a

battery is properly connected. Unlike

traditional chargers, the clips will not

spark if touched together.

No problem, this is a normal condition.

201

051111

PN=15

Storage

OURGP11,00000C7 1929MAR111/1

Storing Battery Charger

CAUTION: Battery electrolyte is dangerous and

corrosive. Wear eye protection and protective

clothing when cleaning ring lugs.

Clean clips each time battery charger is used to prevent

corrosion from battery electrolyte.

Clean case and cords with dry or slightly damp cloth.

Store battery charger in a clean, dry place.

TYB6043 —UN—08FEB11

TY26877 Battery Charger

251

051111

PN=16

Specifications

OURGP11,00000C8 1907APR111/1

OURGP11,00000C9 1908FEB111/1

Battery Charger Specifications

Speciﬁcations

Model TY26877

Type

Fully Automatic Microprocessor Controll

Output Voltage 12 VDC

Input Voltage

120 VAC

Output Current Continuous

6 Amps

Input Current Continuous

5.3 Amps

Height

257 mm (10.12 in.)

Width

269 mm (10.60 in.)

Depth

103 mm (4.06 in.)

Weight

5 kg (10.98 lb)

Record Product Information

Write your John Deere part number, date code, and date

of purchase in the spaces provided below. Your dealer

needs this information when ordering parts and when

filing warranty claims.

John Deere Part Number: TY26877

Date of Purchase

(To be filled in by purchaser)

301

051111

PN=17

Warranty

OURGP11,00000CA 1929MAR111/1

Warranty

John Deere Company (“John Deere”) warrants to the

original purchaser of each new John Deere Battery

Charger that it will repair or replace, as John Deere elects,

any part of the battery charger that is defective in material

or workmanship as delivered to the purchaser if the defect

appears within one year from date of purchase. This

warranty applies only to purchases from authorized John

Deere dealers.

To obtain performance of this warranty, the purchaser

must request such performance from a John Deere dealer

authorized to sell new John Deere Battery Chargers. At

the time of such request, the purchaser must present

proof of purchase documentation that includes a date of

purchase (bill of sale, for example), make the product

available at the dealer’s place of business, and inform the

dealer of what the purchaser believes to be the defect in

the product.

If John Deere elects to repair the product, only new

or remanufactured parts or components, furnished or

approved by John Deere, will be used. If any such part or

component is defective in material or workmanship when

installed in the product, John Deere will repair or replace,

as it elects, such defective part or component provided

the defect is reported to an authorized John Deere dealer

within 90 days of installation or before expiration of the

product’s warranty, whichever is later.

John Deere is not responsible for the following:

1. Transportation to and from the dealership, or service

calls made by the dealer.

2. Used products of any make.

3. Any product that has been altered or modified in ways

not approved by John Deere.

4. Depreciation or damage caused by normal wear, lack

of reasonable and proper maintenance, failure to

follow operating instructions, misuse, or lack of proper

protection during storage.

5. Normal maintenance and replacement of wear items.

6. Premiums charged for overtime labor requested by

the purchaser.

Other than as stated in this section of the manual,

neither John Deere nor any company affiliated with

it makes any warranties, or representations, as to

materials, workmanship, quality or performance of

the products covered under this warranty. IMPLIED

WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, ARE

EXPRESSLY DISCLAIMED. THE ONLY REMEDIES

THE PURCHASER HAS IN CONNECTION WITH THE

BREACH OF PERFORMANCE OF ANY WARRANTY

ON JOHN DEERE PRODUCTS ARE THOSE SET

FORTH HEREIN. IN NO EVENT WILL THE DEALER,

JOHN DEERE, OR ANY COMPANY AFFILIATED WITH

JOHN DEERE BE LIABLE FOR INCIDENTAL OR

CONSEQUENTIAL DAMAGES. (NOTE: SOME STATES

DO NOT ALLOW LIMITATIONS ON HOW LONG AN

IMPLIED WARRANTY LASTS OR THE EXCLUSION OR

LIMITATION OF INCIDENTAL OR CONSEQUENTIAL

DAMAGES, SO THE ABOVE LIMITATIONS AND

EXCLUSIONS MAY NOT APPLY TO YOU.)

The selling dealer makes no warranty of his own on any

item warranted by John Deere, and makes no warranty

on any other item unless he delivers to the purchaser a

separate written warranty certificate specifically warranting

the item. The dealer has no authority to make any

representation or promise on behalf of John Deere, or to

modify the terms or limitations of this warranty in any way.

NOTE: This warranty gives you specific legal

rights, and you may have other rights which

vary from state to state.

351

051111

PN=18

La page est en cours de chargement...

Schumacher TY26877 John Deere Four Independent Station Battery Charger JD-406A Le manuel du propriétaire

Marque: Schumacher

Modèle: TY26877 John Deere Four Independent Station Battery Charger JD-406A

Catégorie: Chargeurs de batterie de voiture

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Schumacher TY26877 John Deere Four Independent Station Battery Charger JD-406A Owner's manual

Schumacher TY26877 John Deere Four Independent Station Battery Charger JD-406A Le manuel du propriétaire

Schumacher TY26877 John Deere Four Independent Station Battery Charger JD-406A Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents