ClearSounds CS-A300 Manuel utilisateur

1 – ENGLISH

FRANÇAIS ESPAÑOL ENGLISH

CS-A300 DECT 6.0

Cordless Phone

V508

A300E.indd 1 7/11/08 11:52:06 AM

2 – ENGLISH

3 – ENGLISH

Congratulations on your purchase of the CS-A300 Phone from

ClearSounds Communications

®

. Please read this User Guide carefully

in order to get the very best results from your telephone. Keep the

manual near the telephone for easy reference.

Please visit our web site at www.clearsounds.com to: Register your product,

download additional manuals, and review trouble shooting tips.

Due to the nature of VOIP/Broadband technology results may vary when

used with VOIP/Broadband service

Important Safety Instructions

Read and understand the Installation Guide & User Manual. When using

your telephone equipment, basic safety precautions should always be

followed to reduce the risk of fire, electric shock and injury to person,

including the following:

WARNING: Follow all warnings and instructions marked on the telephone.

WARNING: The ClearSounds A300 is capable of amplifying sounds to a loud

volume. It is important to instruct all potential users of its proper operation.

It is advised to adjust the volume control to the minimum level (Low) when

not in use and alert other users that hearing damage can potentially result

from misuse.

WARNING: To avoid the possibility of electrical shock, do not use this

product near water (For example, near a bathtub, wash basin, kitchen sink

or laundry tub, in a wet basement or near a swimming pool) while in the

bathtub or shower or when you are wet. If the phone becomes submerged

in water, do not attempt to retrieve it until after you have unplugged the

line cord from the modular wall jack. Do not plug the phone back in until it

has dried completely.

WARNING: Avoid using the telephone during electrical storms. There may

be a remote risk of electric shock from lightning. If the electrical storm is

present in your immediate area, possibility of electrical shock exists.

WARNING: Do not use the phone if you suspect a gas leak in the area. The

phone’s electrical contacts could create a spark, which could ignite any

heavy concentration of leaking gas.

WARNING: Unplug this telephone from wall outlet before cleaning. Do not

use liquid cleaners or aerosol cleaners on the telephone. Use a damp cloth

for cleaning.

WARNING: No telephone should ever be placed near an open radiator or

heating register.

WARNING: Occasionally a power surge can occur on electrical lines without

warning. With any electrical device that you plug into an outlet, it is

suggested you use a surge protector. A surge protector will prevent power

A300E.indd 2 7/11/08 11:52:06 AM

2 – ENGLISH

3 – ENGLISH

surges from damaging your telephone. Surge protectors are simple devices

available at your local hardware store.

WARNING: Do not overload wall outlet or extension cords, as this can

increase the risk of fire or electrical shock.

WARNING: Never push any objects through the slots in the phone. They can

touch dangerous voltage points or short out parts that could result in a risk

of fire or electrical shock.

Component List

Carefully remove your cordless telephone from its box. Check to be

sure you have all items that come with your telephone. You should

have a TELEPHONE BASE UNIT, TELEPHONE HANDSET, BELT CLIP,

TELEPHONE LINE CORD, AC ADAPTER, 3 AAA Ni-MH RECHARGEABLE

BATTERIES AND OWNER’S MANUAL.

A300E.indd 3 7/11/08 11:52:06 AM

4 – ENGLISH

5 – ENGLISH

HANDSET

FUNCTIONS/KEYS

1 Visual Ringer

2 One-touch memories M1-M4

3 Display

4 Right Soft Key

5 Right Key

6 End

7 Down Key

8 Alphanumeric Keys

9 Microphone

10 Dial Key

11 Left Key

12 Left Soft Key

13 Up key

14 Earpiece

15 Carrying Clip

16 SOS Button

17 Battery Compartment Cover

18 Charging Contacts

19 Headset Jack

BASE

20 Charging Pins

21 Charge Indicator – Lights

steadily while the handset is

charging

22 Page Button

BASE BOTTOM VIEW

23 Phone Line Jack

24 Power Jack













































 

A300E.indd 4 7/11/08 11:52:08 AM

4 – ENGLISH

5 – ENGLISH

KEY DESCRIPTION:

Icon Key Function

Dial Key Use to Make or Answer a Call

End Key End a call. Long press to activate power on/off

Up Key Scroll up through lists and menu options. Increase

the earpiece/speakerphone volume during a call.

Enter the CID book as described in section -

Down Key Scroll down through lists and menu options.

Decrease the earpiece/speakerphone volume

during a call. Enter the phonebook as described

in section -

Left Key Set up an internal call to another handset. Transfer

an incoming call with an external line and an

internal handset

Right Key Enter the redial book, as described in section -

Left/Right

Soft Key

Perform the functions indicated by the text

immediately over it (on the bottom line of the

display) which changes time by time.

Star Key Press and hold to turn on/off keypad lock function.

Set up a conference call, as described in section -

One touch

Dial

You can store up to 5 number in one-touch dialing

buttons M1-M4 and SOS (Located on Back of

Handset)

0 Key In standby mode press and hold this key until the

ZZ icon appears to activate the shake and visual

ringer function. Press and hold this key again until

the Icon disappears to deactivate it.

A300E.indd 5 7/11/08 11:52:09 AM

6 – ENGLISH

7 – ENGLISH

LCD WINDOW ICONS DESCRIPTON

Icon Function

New Call Indicates you have missed one or more calls

MSG Waiting Indicates you have one more voice messages

Off Hook Indicates the line is engaged

Hands-Free Indicates the handsfree function is enabled

Battery Icon Indicates battery charge level

Shake Icon Indicates the shaker and visual ringer is

enabled

Signal Icon Indicates the current signal strength. If the

handset is too far from the base, this icon will

blink on the LCD.

Alarm Icon This Icon appears when you set an alarm to

ring at a specified time.

Keypad Lock This icon appears when the keypad is locked

ICM Icon This icon appears when you have new

messages

Telephone Set-up

Choose a location for the base near an electrical outlet and a telephone jack.

Connect one end of the phone line cord to the base of the phone and

the other end to a standard phone wall outlet.

Connect the modular end of the AC power adapter to the power jack of

the base, and then plug the AC Adapter into a standard AC wall outlet.

Installing Batteries

Handset batteries MUST be connected before beginning initial

charging!

Remove battery compartment cover by removing the memory

dial reference card by sliding it downwards. Then using the small

screwdriver (provided).

Install new batteries. Be sure to observe battery polarity as imprinted

on the base of the compartment

Replace the battery compartment cover and replace the screw to

secure the cover.

NOTE: Reversing the orientation of the batteries may damage the

handset.

A300E.indd 6 7/11/08 11:52:10 AM

6 – ENGLISH

7 – ENGLISH

The batteries need to be replaced if they do not recover their full

storage capacity after recharging

When replacing the batteries always use good quality NiMH AAA

rechargeable batteries.

Handset Battery Charging

Place the handset into the base. The charge indicator LED on the

Telephone base will light up.

Choose a location for the base near an electrical outlet and a

telephone jack.

1 Connect one end of the phone line cord to the base of the phone and the

other end to a standard phone wall outlet.

2 Connect the modular end of the AC power adapter to the power jack of

the base, and then plug the AC Adapter into a standard AC wall outlet.

Installing Batteries

Handset batteries MUST be inserted before beginning initial charging!

Remove battery compartment cover by removing the memory 1.

dial reference card by sliding it downwards. Then using the small

screwdriver (provided).

Install new batteries. Be sure to observe battery polarity as 2.

imprinted on the base of the compartment

Replace the battery compartment cover and replace the screw to 3.

secure the cover.

NOTE:

Reversing the orientation of the batteries may damage the •

handset.

The batteries need to be replaced if they do not recover their •

full storage capacity after recharging

When replacing the batteries always use good quality NiMH AAA •

rechargeable batteries.

Handset Battery Charging

Place the handset into the base. The charge indicator LED on the 1.

base will light RED.

IMPORTANT: The batteries in the handset must be fully charged 2.

for 14-16 hours before using the telephone for the first time.

After the batteries are fully charged, check for dial tone by 3.

pressing the talk button on the handset.

Using the Handset Carrying Clip

The handset carrying clip allows you to carry the handset with you,

it clips easily to your belt, waist band, or shirt pocket.

Note: If you want to remove the carrying clip insert a screw driver

A300E.indd 7 7/11/08 11:52:10 AM

8 – ENGLISH

9 – ENGLISH

along the edge of one of the “arms” and release the clip. It should

then lift off easily.

Turning the Handset On/Off

If the handset is in off mode when you place the handset on the base,

it automatically turns on. To turn the handset on or off in standby

mode, follow these steps:

To turn the handset on when it’s off, press and hold the END KEY

until you switch the display on. On power up, the handset will enter

subscription mode and search for a registered base. A message as

shown here will be displayed to the user, and the Antenna Icon will

flash.

To turn the handset off, key the END KEY key pressed until the display

turns off.

NOTES: If the handset is successful in finding a base, the handset

will enter the Standby mode, the display will show handset number

and the handset name, antenna icon, battery icon, and current time.

If the handset is not successful in finding a base, the handset will

behave according to the Out of Range condition.

Nothing will appear on the LCD when battery power is very low. YOU SHOULD

FULLY CHARGE THE HANDSET BEFORE USING.

BASIC A300 OPERATION

Answering a Call

If the handset is off of the base, press the DIAL KEY to receive the call. The

OFF HOOK ICON will appear on the LCD.

Or if you activated the Auto Answer Function - If the handset is in the base,

lift the handset to receive the call.

When you are finished with your call either press the END KEY or

replace the handset on the base.

NOTE: When you finish the call the LCD displays the call duration

time.

Making a Call

Pick up the handset and press the DIAL KEY and wait for a dial

tone.

A300E.indd 8 7/11/08 11:52:11 AM

8 – ENGLISH

9 – ENGLISH

Dial the telephone number.

Adjust your Volume and Tone setting if needed.

To end the call, just press the END KEY or return to base or charger.

Pre-Dial

You can also pre-dial a number in standby mode, which will allow

you to make corrections before dialing.

Enter a phone number (up to 32 digits to use a calling card or dial

internationally use the RIGHT key to insert a Pause), review the number.

When the correct number appears, press the DIAL KEY.

NOTES: If you make a mistake while entering a number, press the

ERASE soft key to clear the last digit You can store up to 10 tele-

phone numbers in the memory for automatic dialing You can also

make a call to the last number dialed by using the redial feature. As

featured in Last Number Redial.

Adjusting the Volume while in use

During the conversation you can use the UP or DOWN KEY to adjust

the level of the earpiece (or hands-free speakerphone - if activated)

from V1- V5. The selected volume will be display on the LCD.

You can also select the earpiece volume or the speaker volume by

the Audio Setup menu.

Muting the Microphone

During a conversation you can temporarily switch your phone’s

microphone off, so that the other party cannot hear you.

To mute the microphone Press the MUTE SOFT key during the

conversation. “Call Muted” appears on the LCD screen.

To un-mute the microphone press the MUTE SOFT key again, this will

restore normal condition.

Using the Speakerphone

During a conversation you can turn on the speakerphone built in the

handset. When using the Speakerphone you can simply put your

handset down and enjoy a handsfree conversation.

To turn the speakerphone on, press the DIAL KEY during a call, the

line must be in-use for the speakerphone feature to work.

To turn the speakerphone off, simply press the DIAL KEY again during

your conversation.

NOTE: Before picking up the handset and putting it up to your ear be

A300E.indd 9 7/11/08 11:52:11 AM

10 – ENGLISH

11 – ENGLISH

sure you have turned the speakerphone off.

Using a Headset with your A300

You can use this telephone hands-free when you connect a 2.5mm

headset (purchased separately). To connect, plug the headset into the

HEADSET JACK on the left side of the handset. While in the Headset

Mode, the volume of the headset is controlled by the telephone and

the handset’s earpiece and microphone are disconnected.

Using the Soft Key and Menus

In the LCD screen you will see the Menu and TAM options for setting

up and using your A300.

While in standby mode you will use the Soft Keys to select which

function from the Menu and set-up your phone.

A300E.indd 10 7/11/08 11:52:11 AM

10 – ENGLISH

11 – ENGLISH

For example:

Setting the Earpiece Volume

----- Main Menu -----

Phonebook

BS Setting

HS Settings

LCD Screen #2

LCD Screen #3

LCD Screen #4

LCD Screen #5

TAMMenu

BACKSELECT

HS1

01/01 05:26 pm

LCD Screen #1

BACKSAVE

----- HS Settings -----

Alarm

Audio Setup

Ring Setup

-----Audio Setup -----

----- END -----

Speaker V

Earpiece V

----- Earpiece Volume -----

Volume 5

Volume 4

Volume 3

Press the LEFT SOFT KEY under Menu in

the LCD Screen

Press the UP or DOWN KEY to scroll

through the menu and select HS

Settings by pressing the LEFT SOFT KEY

----- Main Menu -----

Phonebook

BS Setting

HS Settings

LCD Screen #2

LCD Screen #3

LCD Screen #4

LCD Screen #5

TAMMenu

BACKSELECT

HS1

01/01 05:26 pm

LCD Screen #1

BACKSAVE

----- HS Settings -----

Alarm

Audio Setup

Ring Setup

-----Audio Setup -----

----- END -----

Speaker V

Earpiece V

----- Earpiece Volume -----

Volume 5

Volume 4

Volume 3

Press the LEFT SOFT KEY to select HS

Settings

Press the DOWN KEY to scroll through the

menu and select Audio Setup

----- Main Menu -----

Phonebook

BS Setting

HS Settings

LCD Screen #2

LCD Screen #3

LCD Screen #4

LCD Screen #5

TAMMenu

BACKSELECT

HS1

01/01 05:26 pm

LCD Screen #1

BACKSAVE

----- HS Settings -----

Alarm

Audio Setup

Ring Setup

-----Audio Setup -----

----- END -----

Speaker V

Earpiece V

----- Earpiece Volume -----

Volume 5

Volume 4

Volume 3

Press the LEFT SOFT KEY to select Audio

Setup

Press the UP or DOWN KEY to scroll

through the menu and select Earpiece V

by pressing the LEFT SOFT KEY

----- Main Menu -----

Phonebook

BS Setting

HS Settings

LCD Screen #2

LCD Screen #3

LCD Screen #4

LCD Screen #5

TAMMenu

BACKSELECT

HS1

01/01 05:26 pm

LCD Screen #1

BACKSAVE

----- HS Settings -----

Alarm

Audio Setup

Ring Setup

-----Audio Setup -----

----- END -----

Speaker V

Earpiece V

----- Earpiece Volume -----

Volume 5

Volume 4

Volume 3

Press the LEFT SOFT KEY to select

Earpiece V

Press the UP or DOWN KEY to scroll

through the menu and select Volume 5 –

Volume 1 by pressing the LEFT SOFT KEY

----- Main Menu -----

Phonebook

BS Setting

HS Settings

LCD Screen #2

LCD Screen #3

LCD Screen #4

LCD Screen #5

TAMMenu

BACKSELECT

HS1

01/01 05:26 pm

LCD Screen #1

BACKSAVE

----- HS Settings -----

Alarm

Audio Setup

Ring Setup

-----Audio Setup -----

----- END -----

Speaker V

Earpiece V

----- Earpiece Volume -----

Volume 5

Volume 4

Volume 3

Press the LEFT SOFT KEY to SAVE your

selection. You will hear a confirmation

beep.

You can press the Right Soft Key under the BACK display in the

LCD to move back through the menu selections – OR – you can wait

and in approximately 30 seconds the phone will return to standby

mode.

A300E.indd 11 7/11/08 11:52:11 AM

12 – ENGLISH

13 – ENGLISH

Setting the Ringer Volume

Press the SOFT KEY under Menu in the LCD Screen.

Press the UP or DOWN KEY to scroll through the menu and select

HS Settings by pressing the LEFT SOFT KEY

Press the DOWN KEY again to scroll to RING SETUP then press the

SOFT KEY to make your selection.

Press the DOWN KEY again to select INT RING or EXT RING press

the SOFT KEY to select

Press the DOWN KEY again to select VOLUME press the SOFT KEY

Use the Up and Dow Keys to scroll through the volume selections

Volume 1 through Volume 5 and No Volume. Press the SOFT KEY to

Save. You will hear a confirmation tone to confirm your selection has

been saved.

Setting the Ringer Melody

Press the SOFT KEY under Menu in the LCD Screen.

Press the DOWN KEY to scroll through the menu and select HS

SETTINGS by pressing the SOFT KEY

Press the DOWN KEY again to scroll to RING SETUP then press the

SOFT KEY to make your selection.

Press the DOWN KEY again to select INT RING or EXT RING press

the SOFT KEY to select

Press the DOWN KEY again to select MELODY press the SOFT KEY

Use the UP or DOWN Keys to scroll through the Melody selections

Melody 1 through Melody 10. Press the SOFT KEY to Save. You will

hear two confirmation tones to confirm your selection has been

saved.

NOTE: If you turn the ringer OFF, when a call comes in, only the New

Call information appears on the LCD. If you activate the shaker and

visual ringer function when a call comes in the handset will shake and

the visual ringer will also flash with the ring melody you have set.

Last Number Redial

Press the RIGHT KEY in Standby mode.

The LCD will display the lat number you dialed

Press the DIAL KEY to dial the number

Note: The A300 allows you to retrieve the last 10 numbers you have

dialed and recall them quickly.

A300E.indd 12 7/11/08 11:52:11 AM

12 – ENGLISH

13 – ENGLISH

Search for and Dial a number in the Redial book.

Press the RIGHT KEY in standby mode

If you want to scroll through the memory, press the UP or DOWN

KEY until you find the number you want to dial

Press the DIAL KEY to dial the number

NOTE: If no numbers are found “EMPTY” is displayed on the redial

book screen. When the redial book is full, each time you dial a new

number, the oldest number stored in the redial book is automatically

erased, and it is updated.

Use Redial book options.

This allows you to delete a number from your redial book or add a

number to your phone book.

Press the RIGHT KEY in standby mode

Press the UP or DOWN KEY to scroll the memory until you find the

number you want to delete

When the number appears on the screen, press the SOFT KEY to

select MORE. You will have 3 options ADD TO PB, DELETE,

DELETE ALL

ADD to PB, allows you to add the number to your phone book.

Use the RIGHT KEY to enter the redial phonebook

Use the SOFT KEY to select MORE

Use the SOFT KEY to select ADD TO PB

Enter the Name, press the SOFT KEY to select NEXT

Number? Will appear and you can edit the number if needed, if the

number is fine use the SOFT KEY to select NEXT

Press the UP or DOWN KEY to scroll through to select a Melody to

be associated with the number

Use the SOFT KEY to select SAVE

DELETE

Use the RIGHT KEY to enter the redial phonebook

Press the DOWN KEY to scroll through the numbers to select the

number you want to delete

Use the SOFT KEY to select MORE

Use the SOFT KEY to select DELETE

A300E.indd 13 7/11/08 11:52:11 AM

14 – ENGLISH

15 – ENGLISH

The screen will display “CONFIRM” use the SOFT KEY to select DEL

to confirm, you will hear a confirmation tone.

DELETE ALL

Use the RIGHT KEY to enter the redial phonebook

Use the SOFT KEY to select MORE

Press the DOWN KEY to scroll the through the menu and select

DELETE ALL

The screen will display “CONFIRM?”, use the SOFT KEY to select DEL

ALL

ANSWERING MACHINE FUNCTIONS

Recording your Greeting – Announce 1 (this

selection allows your caller to leave a message)

You can record your own greeting our use the standard default greeting

which is “Hello, your call cannot be taken at the moment, to record your

message, please speak after the tone.”

Press the SOFT KEY under TAM in the LCD Screen.

Press the UP or DOWN KEY to scroll through the menu and select

Announce by pressing the SOFT KEY

Press the DOWN KEY again to scroll to ANNOUNCE 1 then press

the SOFT KEY to make your selection.

Press the DOWN KEY again to select RECORD or DEFAULT press

the SOFT KEY to select

If you select RECORD you will be instructed to start speaking after

the tone, when nished with your greeting press the SOFT KEY to

conrm. If you need to stop and start over you can press the SOFT

KEY ICON under OK, during recording the LCD screen will show

“RECORDING….”

Your message will be played back automatically for your review.

Recording your Greeting – Annouce 2 (this feature

is a message only, callers are not allowed to leave

a message if you select this option)

You can record your own greeting our use the standard default

greeting which is “Hello, your call cannot be taken at the moment,

please call back later.”

Press the SOFT KEY under TAM in the LCD Screen.

A300E.indd 14 7/11/08 11:52:11 AM

14 – ENGLISH

15 – ENGLISH

Press the UP or DOWN KEY to scroll through the menu and select

Announce by pressing the SOFT KEY

Press the DOWN KEY again to scroll to ANNOUNCE 2 then press

the SOFT KEY to make your selection.

Press the DOWN KEY again to select RECORD or DEFAULT press

the SOFT KEY to select

If you select RECORD you will be instructed to start speaking after

the tone, when nished with your greeting press the SOFT KEY to

conrm. If you need to stop and start over you can press the SOFT

KEY ICON under OK, during recording the LCD screen will show

“RECORDING….”

Your message will be played back automatically for your review.

Playback Announce 1/Annouce 2

To playback your recorded announcement.

Press the SOFT KEY under TAM in the LCD Screen.

Press the UP or DOWN KEY to scroll through the menu and select

Announce by pressing the SOFT KEY

Press the DOWN KEY again to scroll to ANNOUNCE 1 then press

the SOFT KEY to make your selection.

Press the DOWN KEY again to select Playback press the SOFT KEY

to select

You can use the Back Soft Key to stop and exit.

Restore Announce 1/Annouce 2

Press the SOFT KEY under TAM in the LCD Screen.

Press the UP or DOWN KEY to scroll through the menu and select

ANNOUCE 1 OR ANNOUCE 2 by pressing the SOFT KEY

Press the DOWN KEY again to scroll to DEFAULT then press the

SOFT KEY to make your selection.

The LCD will show CONFIRM?. Press the SOFT KEY to Select the

default Announcement or select BACK by using the SOFT KEY to

cancel.

Play New/Saved Messages

Press the SOFT KEY under TAM while in standby mode

Press the DOWN KEY to scroll through the menu and select MESSAGE

then press the SOFT KEY to make your selection

A300E.indd 15 7/11/08 11:52:11 AM

16 – ENGLISH

17 – ENGLISH

Press the DOWN KEY to scroll to either NEW MSG or SAVED MSG

then press the SOFT KEY to make your selection.

The phone will announce “You have XX new message(s)” or “You

have X saved message(s)”. You can use the 0 key to delete the

current message or using the SOFT KEY select BACK to stop playing

the messages and exit.

Delete all Message

Press the Down Key to Scroll through the menu and Select Message

then press the Soft Key to make your selection Press the SOFT KEY

under TAM while in standby mode

Press the DOWN KEY again to scroll through the menu and select

DELETE ALL then press the SOFT KEY to make your selection

The LCD will show CONFIRM?. Press the SOFT ICON KEY to select

OK to delete all the messages or select Cancel to exit.

NOTE: Your A300 can record up to 15 minutes of messages.

Using the Memo Function

You can use your A300 to record a message for someone else in your

home. The memo can be played back as a message.

Press the SOFT KEY under TAM while in standby mode.

Press the DOWN KEY to scroll through the menu and select MESSAGE

then press the SOFT KEY to make your selection

Press the DOWN KEY to scroll to MEMO RECORD then press the

SOFT KEY to conrm.

You can begin to record your message after hearing the tone.

Recording will stop after 3 minutes, you can also confirm and end

the recording by selecting OK using the Soft Key. During recording

the LCD shows “Recording…”

Note: When leaving a memo the ICM ICON will appear on the LCD

screen while in standby mode.

SETTING UP YOUR ANSWERING MACHINE

Turning your Answering Machine On/Off

Press the SOFT KEY under TAM while in standby mode.

Press the DOWN KEY to scroll through the menu and select TAM

SETTING then press the SOFT KEY to make your selection

Press the DOWN KEY to scroll to TAM On/Off then press the SOFT

KEY to conrm.

A300E.indd 16 7/11/08 11:52:11 AM

16 – ENGLISH

17 – ENGLISH

Press the DOWN KEY to scroll through the menu and select either

Off or On then press the SOFT KEY to make your selection

Using the The Answering Machine Alert

You can set-up your A300 to alert you with a Tone when you receive

a new message

Press the SOFT KEY under TAM while in standby mode.

Press the DOWN KEY to scroll through the menu and select TAM

SETTING then press the SOFT KEY to make your selection

Press the DOWN KEY to scroll to TAM Alert then press the SOFT

KEY to conrm.

Press the DOWN KEY to scroll through the menu and select either

Off or On then press the SOFT KEY to make your selection

Selecting An Answer Mode

Your A300 answering machine operates in two modes, answer and

record (Announce 1), and answer only (Announce 2).

Press the SOFT KEY under TAM while in standby mode.

Press the DOWN KEY to scroll through the menu and select TAM

SETTING then press the SOFT KEY to make your selection

Press the DOWN KEY to scroll to ANNC Select then press the SOFT

KEY to conrm.

Press the DOWN KEY to scroll through the menu and select either

Announce 1 or Announce 2 then press the SOFT KEY to make your

selection

NOTE: Announce 2 will be played when your answering machine is

full, even if you have selected Announce 1.

Setting the Ring Delay

You can select the number of rings before your answering machine

takes an incoming call. You can select from 2 to 6 rings or Toll Saver

mode.

Press the SOFT KEY under TAM while in standby mode.

Press the DOWN KEY to scroll through the menu and select TAM

SETTING then press the SOFT KEY to make your selection

Press the DOWN KEY to scroll to SET RING then press the SOFT

KEY to conrm.

Press the DOWN KEY to scroll through the menu and select  2 -6

rings or Toll Saver. then press the SOFT KEY to make your selection

A300E.indd 17 7/11/08 11:52:11 AM

18 – ENGLISH

19 – ENGLISH

NOTE: If you select Toll Saver, when there are new messages waiting

to be played back, the answering machine will respond after 3 rings,

if you have no new messages to be reviewed it will answer after 6

rings.

Setting the Language

You can select language for your default Announce 1 or Announce 2.

Press the SOFT KEY under TAM while in standby mode.

Press the DOWN KEY to scroll through the menu and select TAM

SETTING then press the SOFT KEY to make your selection

Press the DOWN KEY to scroll to TAM Language then press the

SOFT KEY to conrm.

Press the DOWN KEY to scroll through the menu and select the

language (English is default) then press the SOFT KEY to make your

selection

Re-setting your Answering Machine

This function allows you to reset your Answering Machine to the

factory default settings.

Press the SOFT KEY under TAM while in standby mode.

Press the DOWN KEY to scroll through the menu and select TAM

SETTING then press the SOFT KEY to make your selection

Press the DOWN KEY to scroll to TAM Default Select then press the

SOFT KEY to conrm.

You will prompted to enter a PIN Code (default is 0000), then press

the SOFT KEY ICON to select RESET. If the PIN Code is validated all

answering machine settings will return to the factory default, otherwise

a warning tone will be heard and the settings will remain as you have

programmed them.

Note: After resetting, the Answering machine will reset and return

to standby mode.

Setting up a Remote Code

This function allows you to operate you answering machine remotely

from another location. For security purposes we recommend that

you change the code (the default is 0000).

Press the SOFT KEY under TAM while in standby mode.

Press the DOWN KEY to scroll through the menu and select TAM

SETTING then press the SOFT KEY to make your selection

A300E.indd 18 7/11/08 11:52:12 AM

18 – ENGLISH

19 – ENGLISH

Press the DOWN KEY to scroll to REMOTE CODE then press the

SOFT KEY to conrm.

The LCD will show the current code, enter the new code you want to set

then press the Soft Key to Select OK.

Using the Remote Function

This feature allows you to access your answering machine remotely.

Simply dial your phone number from any touch tone phone, then

enter your 4 digit security code (factory default is 0000).

Dial your phone using any touch tone telephone

When your greeting (or default greeting) begins to play, you can

enter your security code.

After entering the security code, the system will play the menu of

commands. You can then follow the commands to retrieve messages, etc.

Remote Access Commands

1 Play main menu

2 Play new messages

3 Play saved messages

0 Delete all messages

5 Switch the answering machine on/off

6 Record Announce 1 of 2

(this depends on your announce setting)

Press the # to nish recording

NOTE: If you enter the wrong security code the A300 will announce

you need to enter the code again. You will have a total of 3 tries to

enter the correct security code before the line is disconnected

You should also stop playing messages before ending the call.

PHONE BOOK

The phonebook in your A300 allows you to store frequently called numbers.

Character Map

To enter a specific alphanumeric character, press one or more times the key

for the required character according to the following table: once for the first

character, twice for the second and so on.

Key Character

(spc) 0 ? & / . , !

1 @ _ + - “ ( ) %

A B C a b c 2

A300E.indd 19 7/11/08 11:52:12 AM

20 – ENGLISH

21 – ENGLISH

D E F d e f 3

G H I g h I 4

J K L j k l 5

M N O m n o 6

P Q R S p q r s 7

T U V t u v 8

W X Y Z w x y z 9

Adding names to the phone book

Press the SOFT KEY under MENU while in standby mode.

Press the DOWN KEY to scroll through the menu and select

PHONEBOOK then press the SOFT KEY to make your selection

Press the DOWN KEY to scroll to NEW then press the SOFT KEY to

confirm.

The display will show NAME? Enter the name you want to use, then

press the Soft Key to select NEXT. The display will show NUMBER?

Enter the phone number (up to 20 digits) then using the Soft Key

select NEXT.

Use the DOWN KEY to select the Melody you would like to associate

with the number, using the Soft Key select SAVE to confirm.

Repeat as necessary

NOTE: If you make a mistake while entering a number, use the Soft

Key to select Erase to correct the mistake. To clear all the numbers

or characters, press and hold Erase.

Inserting A Pause

A pause is useful when you a programming a calling card number,

or you need extra time when accessing a interactive voice response

system i.e. banking by phone. A pause provides a delay of 3 seconds,

if you want to insert a pause when you are dialing a number in

standby mode or store a number in memory press the RIGHT KEY

then the letter P will appear.

Viewing Phone Book Entries

In standby mode press the DOWN KEY

Press the UP or DOWN key repeatedly until the desired number is

displayed.

If you want to dial the selected number, simply press the DIAL KEY.

A300E.indd 20 7/11/08 11:52:12 AM

La page charge ...

ClearSounds CS-A300 Manuel utilisateur

Ce manuel convient également à

ClearSounds CS-A300 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents