FEIN JMU 137-2 QW Manuel utilisateur

Catégorie
Outils électroportatifs
Taper
Manuel utilisateur
© C. & E. Fein GmbH. Printed in USA. Figure not obligatory. Subject to technical changes. 3 41 01 246 21 0 BY 2018.04.
by FEIN
by FEIN
USA
FEIN Power Tools, Inc.
1000 Omega Drive
Suite 1180
Pittsburgh, PA 15205
Phone: 800-441-9878
www.feinus.com
Canada
FEIN Canadian Power Tool
Company
323 Traders Boulevard East
Mississauga, Ontario L4Z 2E5
Telephone: (905) 8901390
Phone: 1-800-265-2581
www.fein.com
FEIN Service USA
FEIN Power Tools, Inc.
2735 Hickory Grove Road
Davenport, IA 52804
Phone: 800-441-9878
magdrillrepair@feinus.com
Headquarter
C. & E. Fein GmbH
Hans-Fein-Straße 81
D-73529 Schwäbisch Gmünd-Bargau
www.fein.com
 JMU 137 QW (**) 7 270 ...
 JMU 137 MQW (**) 7 270 ...
 JMU 137-2 QW (**) 7 270 ...
OBJ_DOKU-0000006757-003.fm Page 1 Wednesday, April 4, 2018 9:31 AM
2
Instruction Manual
Mode d’emploi
Instrucciones de uso
en
3
fr
29
es
55
OBJ_BUCH-0000000261-003.book Page 2 Thursday, January 11, 2018 5:30 PM
3
en
en
For your safety.
Read all safety warnings and
all instructions. Failure to fol-
low the warnings and instructions may result
in electric shock, fire and/or serious injury.
Save all warnings and instructions for future-
reference.
Do not use this power tool before you
have thoroughly read and completely
understood this Instruction Manual, including
the figures, specifications, safety regulations
and the signs indicating DANGER, WARN-
ING and CAUTION.
Only carry out such operations with this
power tool as intended for by the manufac-
turer. Only use cutting tools and accessories
that have been approved by the manufac-
turer.
Please also observe the relevant national
industrial safety regulations.
Non-observance of the safety instructions in
the said documentation can lead to an electric
shock, burns and/or severe injuries.
This Instruction Manual should be kept for
later use and enclosed with the power tool,
should it be passed on or sold.
SAVE THESE INSTRUCTIONS.
The term “power tool” in the warnings refers
to your mains-operated (corded) power tool
or battery operated (cordless) power tool.
General safety rules.
1) Work area safety
a)Keep work area clean and well lit. Clut-
tered or dark areas invite accidents.
b)Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the
dust or fumes.
c) Keep children and bystanders away
while operating a power tool. Distrac-
tion can cause you to lose control.
2) Electrical safety
a)Power tool plugs must match the outlet.
Never modify the plug in any way. Do not
use any adapter plugs with earthed
(grounded) power tools. Unmodified
plugs and matching outlets will reduce
risk of electric shock.
b)Avoid body contact with earthed or
grounded surfaces such as pipes, radia-
tors, ranges and refrigerators. There is
an increased risk of electric shock if
your body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power
tool will increase the risk of electric
shock.
d)Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase
the risk of electric shock.
e) When operating a power tool outdoors,
use an extension cord suitable for out-
door use. Use of a cord suitable for out-
door use reduces the risk of electric
shock.
f) If operating a power tool in a damp loca-
tion is unavoidable, use a ground fault
circuit interrupter (GFCI) protected sup-
ply. Use of an GFCI reduces the risk of
electric shock.
3) Personal safety
a)Stay alert, watch what you are doing
and use common sense when operating
a power tool. Do not use a power tool
while you are tired or under the influ-
ence of drugs, alcohol or medication. A
moment of inattention while operating
power tools may result in serious per-
sonal injury.
b)Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing pro-
tection used for appropriate conditions
will reduce personal injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off-position before
connecting to power source and/or bat-
tery pack, picking up or carrying the
tool. Carrying power tools with your
finger on the switch or energising
power tools that have the switch on
invites accidents.
WARNING
OBJ_BUCH-0000000261-003.book Page 3 Thursday, January 11, 2018 5:30 PM
4
en
d)Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotat-
ing part of the power tool may result in
personal injury.
e) Do not overreach. Keep proper footing
and balance at all times. This enables
better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose cloth-
ing or jewelery. Keep your hair, clothing
and gloves away from moving parts.
Loose clothes, jewelry or long hair can
be caught in moving parts.
g)If devices are provided for the connec-
tion of dust extraction and collection
facilities, ensure these are connected
and properly used. Use of dust collec-
tion can reduce dust-related hazards.
4) Power tool use and care
a)Do not force the power tool. Use the cor-
rect power tool for your application. The
correct power tool will do the job bet-
ter and safer at the rate for which it was
designed.
b)Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the
switch is dangerous and must be
repaired.
c) Disconnect the plug from the power
source and/or the battery pack from the
power tool before making any adjust-
ments, changing accessories, or storing
power tools. Such preventive safety
measures reduce the risk of starting the
power tool accidentally.
d)Store idle power tools out of the reach of
children and do not allow persons unfa-
miliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands
of untrained users.
e) Maintain power tools. Check for mis-
alignment or binding of moving parts,
breakage of parts and any other condi-
tion that may affect the power tool’s
operation. If damaged, have the power
tool repaired before use. Many accidents
are caused by poorly maintained power
tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely to
bind and are easier to control.
g)Use the power tool, accessories and tool
bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to be
performed. Use of the power tool for
operations different from those
intended could result in a hazardous sit-
uation.
5) Service
a)Have your power tool serviced by a qual-
ified repair person using only identical
replacement parts. This will ensure that
the safety of the power tool is main-
tained.
Special safety instructions.
Wear protective equipment. Depending on the
application, wear face shield or safety gog-
gles. Wear hearing protection. The safety
glasses/goggles must be suitable to protect
against the particles emitted from different
operations. Continuous high exposure to
noise can lead to loss of hearing.
Do not touch the sharp edges of the core drill
bit. Danger of injury.
Replace the protective cable bushing immedi-
ately when damaged. A defective protective
cable bushing can lead to overheating of the
machine and to an emergency stop.
Before putting into operation: Mount the chip
guard to the machine.
Always secure the power tool with with the
supplied clamping strap. In case of a power
failure or when the power plug is pulled, the
magnetic holding power is not maintained.
When carrying out such work, beware of fall-
ing objects, such as cores or chips.
OBJ_BUCH-0000000261-003.book Page 4 Thursday, January 11, 2018 5:30 PM
5
en
When working overhead or on vertical sur-
faces, the coolant container must not be used.
Use Slugger Cutting Paste instead. Liquids
penetrating your electric power tool may-
cause electric shock.
Avoid touching the drilled core that is auto-
matically ejected by the pilot pin when the
working procedure is finished. Contact with
the core when it is hot, or if it falls, can cause
personal injuries.
Operate the power tool only from grounded
contact sockets that comply with the specifi-
cations. Do not use any connection cables
that are damaged; use extension cables with
a grounded contact that are checked at regu-
lar intervals. A ground conductor without
continuity can cause an electric shock.
To prevent injuries, always keep your hands,
clothing, etc. away from rotating chips. The
chips can cause injuries. Always use the chip
guard.
Do not attempt to remove the cutting tool if it
still turns. This can lead to serious injuries.
Hold power tool by insulated gripping sur-
faces when performing an operation where
the cutting accessory may contact hidden
wiring or its own cord. Cutting accessory con-
tacting a “live” wire will make exposed metal
parts of the power tool “live” and shock the
operator.
Beware of any concealed electric cables, gas
or water conduits. Check the working area
before commencing work, e. g. with a metal
detector.
Do not work materials containing magnesium.
Danger of fire.
Do not work CFP (carbon-fiber-reinforced
polymer) and materials containing asbestos.
These materials are considered carcinogenic.
Do not rivet or screw any name-plates or
signs onto the power tool. If the insulation is
damaged, protection against an electric shock
will be ineffective. Adhesive labels are recom-
mended.
Do not overload the power tool or the storage
case and do not use it as a ladder or stand.
Overloading or standing on the power tool or
the storage case can lead to the upward shift-
ing of the center of gravity of the power tool
or the storage case, and its tipping over.
Do not use accessories which are not specifi-
cally designed and recommended by the
power tool manufacturer. Safe operation is
not ensured merely because an accessory fits
your power tool.
Clean the ventilation openings on the power
tool at regular intervals using non-metal
tools. The blower of the motor draws dust
into the housing. An excessive accumulation
of metallic dust can cause an electrical hazard.
Before putting into operation, check the
power connection and the power plug for
damage.
Recommendation: The tool should always be
supplied with power via a ground fault circuit
interrupter (GFCI) with a rated current of
30 mA or less.
OBJ_BUCH-0000000261-003.book Page 5 Thursday, January 11, 2018 5:30 PM
6
en
Handling hazardous dusts.
When working with power
tools, such as when grinding,
sanding, polishing, sawing or for other work
procedures where material is removed, dusts
develop that are both hazardous to one’s
health and can spontaneously combust or be
explosive.
Contact with or inhaling some dust types can
trigger allergic reactions to the operator or
bystanders and/or lead to respiratory infec-
tions, cancer, birth defects or other reproduc-
tive harm.
Examples of such materials which contain
chemicals that can produce hazardous dusts,
are:
Asbestos and materials containing asbes-
tos;
Lead-containing coatings, some wood
types such as beech and oak;
Minerals and metal;
Silicate particles from bricks, concrete and
other materials containing stone;
Solvent from solvent-containing paint/
varnish;
Arsenic, chromium and other wood pre-
servatives;
Materials for pesticide treatment on boat
and ship hulls;
Stainless steel dust, metal dust and non-
ferrous metal dust;
To minimize the unwanted intake of these
materials:
Use dust extraction matched appropriately
for the developing dust.
Use personal protective equipment, such
as a P2 filter-class dust protection mask.
Provide for good ventilation of the work-
place.
The risk from inhaling dusts depends on how
often these materials are worked. Materials
containing asbestos may only be worked on
by specialists.
Wood and light-metal dust can
cause spontaneous combus-
tion or explosions.
Hot mixtures of sanding dust and paint/var-
nish residuals or other chemical materials in
the filter bag or the vac filter can self-ignite
under unfavourable conditions, such as spark-
ing from sanding metal, continuous sunlight
or high ambient temperatures. To prevent
this:
Avoid overheating the material being
sanded and the power tool.
Empty the dust collector/container rou-
tinely.
Observe the material manufacturer’s
working instructions.
Observe the relevant regulations for the
materials being worked.
WARNING
CAUTION
OBJ_BUCH-0000000261-003.book Page 6 Thursday, January 11, 2018 5:30 PM
7
en
Emission values for sound (Two-figure – specifications as per ISO 4871)
Extension cable.
If the use of an extension cord
is required, its length and con-
ductor cross-section must be adequate for the
application in order to prevent a voltage drop
in the extension cord, power loss and over-
heating of the power tool. Otherwise, the
extension cable and power tool are prone to
electrical danger, and the working efficiency is
decreased.
Sound emission JMU 137 QW (**) JMU 137 MQW (**) JMU 137-2 QW (**)
A-weighted emission
pressure power level mea-
sured at the workplace
L
pA
(re 20 μPa), in deci-
bels 86.7 86.7 85.6
Measuring uncertainty
K
pA
, in decibels 3 3 3
Measured A-weighted
sound power level
L
wA
(re 1 pW), in decibels 97.7 97.7 96.6
Measuring uncertainty
K
wA
, in decibels 3 3 3
C-weighted peak sound
pressure level measured at
the workplace
L
pCpeak
, in
decibels 101.2 101.2 98.9
Measuring uncertainty
K
pCpeak
, in decibels 3 3 3
Mean vibrational value
(core drilling)
m/s
2
ft/s
2
< 2.5
8.3
< 2.5
8.3
< 2.5
8.3
Measuring uncertainty
K
,
in
m/s
2
ft/s
2
1.5
4.9
1.5
4.9
1.5
4.9
REMARK: The sum of the measured emission value and respective measuring inaccuracy
represents the upper limit of the values that can occur during measuring.
Wear hearing protection!
Measured values determined in accordance with the corresponding product standard.
WARNING
OBJ_BUCH-0000000261-003.book Page 7 Thursday, January 11, 2018 5:30 PM
8
en
Intended use of the power tool:
Magnetic core drill unit for drilling with core
drill bits and solid drill bits, reaming, counter-
sinking and tapping on materials with surfaces
suitable for magnets in weather-protected
environments using the application tools and
accessories recommended by Slugger.
Operation of the power tool off power generators.
This power tool is also suitable for use
with AC generators with sufficient power
output that correspond to the Standard
ISO 8528, design type G2. This Standard is
particularly not complied with when the so-
called distortion factor exceeds 10 %. When
in doubt, please refer to the generator
instruction/specification guide.
Operating the power tool off
power generators whose no-
load speed exceeds the voltage value on the
type plate of the power tool is prohibited.
Symbols.
WARNING
Symbol, character Explanation
Make sure to read the enclosed documents such as the
Instruction Manual and the General Safety Instructions.
Observe the instructions in the text or graphic opposite!
Observe the instructions in the text or graphic opposite!
Before commencing this working step, pull the power plug
out of the socket. Otherwise there will be danger of injury if
the power tool should start unintentionally.
Use eye protection during operation.
Use ear protection during operation.
Do not touch the rotating parts of the power tool.
Warning against sharp edges of application tools, such as the
cutting edges of the cutter blades.
Danger of slipping!
Danger of crushes or contusions!
Caution! Falling objects!
Hot surface!
OBJ_BUCH-0000000261-003.book Page 8 Thursday, January 11, 2018 5:30 PM
9
en
Do not reach in!
Fasten strap!
General prohibition sign. This action is prohibited.
This symbol confirms the certification of this product for the
USA and Canada.
This sign warns of a directly imminent, dangerous situation. A
false reaction can cause a severe or fatal injury.
This sign indicates a possible dangerous situation that could
cause severe or fatal injury.
This sign warns of a possible dangerous situation that could
cause injury.
Worn out power tools and other electrotechnical and electri-
cal products should be sorted separately for environmentally-
friendly recycling.
Start drill motor. Rotation direction: clockwise
Stop motor
Low speed
High speed
Magnetic holding power, sufficient
Magnetic holding power, insufficient
Start drill motor. Rotation direction: clockwise
Start drill motor in inch mode. Rotation direction: counter-
clockwise
Speed reduction in steps
Speed increase in steps
Stop motor
Switches the magnet On/Off
(**) may contain numbers and letters
Symbol, character Explanation
DANGER
WARNING
CAUTION
OBJ_BUCH-0000000261-003.book Page 9 Thursday, January 11, 2018 5:30 PM
10
en
Character Unit of measurement,
national
Explanation
n
0
rpm; /min; min
-1
; r/min No-load speed
P
W Electrical power
°Angle width
U V Electric voltage
f Hz Frequency
I
A Electric current intensity
m
lbs Mass
l ft, in Length, width, height, depth, diameter or thread
Ø ft, in Diameter of a round part
m, s, kg, A, mm, V, W,
Hz, N, °C, dB, min, m/s
2
Basic and derived units of measurement from the
international system of units SI.
OBJ_BUCH-0000000261-003.book Page 10 Thursday, January 11, 2018 5:30 PM
11
en
Technical description and specifications.
Before mounting or replacing cutting tool or accessories, pull the power plug.
This preventive safety measure rules out the danger of injuries through acciden-
tal starting of the power tool.
Not all accessories described or shown in this instruction manual will be included with your-
power tool.
WARNING
Application tool
Chip guard
Tool holder
Viseo Touch Pad
Drill-motor cable
Coolant container
Spoke handle
Magnetic foot
Clamping strap
Fig. 1
Switches the magnet On/Off
Starts the drill motor
Rotation direction: clockwise
Speed reduction in steps
Starts the drill motor in inch mode
Rotation direction: anticlockwise
Stops the drill motor
Speed increase in steps
Fig. 2
OBJ_BUCH-0000000261-003.book Page 11 Thursday, January 11, 2018 5:30 PM
12
en
Type JMU 137 QW (**) JMU 137 MQW (**) JMU 137-2 QW (**)
Order number 7 270 ... 7 270 ... 7 270 ...
Current consumption 9.2 A 9.2 A 9.2 A
No-load speed (right rotation)
1. Gear 550 /min 550 /min 550 /min
2. Gear 1700 /min
No-load speed (left rotation)
1. Gear 370 /min 370 /min 370 /min
2. Gear 1140 /min
Drilling capacity in steel - TCT/
high speed steel (core drill bits)
7/16 in – 1 3/8 in
11 mm – 35 mm
7/16 in – 1 3/8 in
11 mm – 35 mm
7/16 in – 1 3/8 in
11 mm – 35 mm
Drilling capacity in steel - high
speed steel (HSS) (twist drill bit)
5/8 in
16 mm
11/16 in
18 mm
5/8 in
16 mm
Tapped hole 9 16/4 in
M14
9 16/4 in
M14
9 16/4 in
M14
Reamer diameter 5/8 in
16 mm
11/16 in
18 mm
5/8 in
16 mm
Counterboring diameter 1 1/4 in
32 mm
1 1/4 in
32 mm
1 1/4 in
32 mm
Weight according to
EPTA-Procedure 01
23.4 lbs
(10.6 kg)
24.25 lbs
(11.0 kg)
24.25 lbs
(11.0 kg)
Class of protection /I /I /I
Allowable ambient temperature 23°F ... 104°F
5°C ... +40°C
23°F ... 104°F
5°C ... +40°C
23°F ... 104°F
5°C ... +40°C
OBJ_BUCH-0000000261-003.book Page 12 Thursday, January 11, 2018 5:30 PM
13
en
Assembly instructions.
Before mounting or replacing cutting tool or accessories, pull the power plug.
This preventive safety measure rules out the danger of injuries through acci-
dental starting of the power tool.
Mounting the spoke handle
(figure 3).
The hub assembly can be mounted on either
side.
Loosen the screw using a hex key.
Remove the spoke handle.
Mount the spoke handle on the other side
and tighten the screw using a hex key.
WARNING
1.
2.
3.
4.
5 mm /
3/16 in
5 mm /
3/16 in
Fig. 3
OBJ_BUCH-0000000261-003.book Page 13 Thursday, January 11, 2018 5:30 PM
14
en
Filling the coolant container.
Prevent the flow of liquid along the cable into the socket outlet or into the core
drill unit, as this can lead to electric shock. Tie a bow in the cable near the plug,
so that any liquid can drip off.
Do not use the magnetic core drill unit when the cooling-lubricant system is defective. Each
time before operating, check for tightness against leaks and for cracks in the hoses. Prevent liq-
uids from entering or penetrating electrical components.
Only use a coolant-lubricant emulsion (oil in water) as the cooling agent.
Observe the manufacturer's instructions on coolant.
Filling the mounted coolant container
(figure 4)
Unscrew the cap from the coolant container.
Fill in pump-feedable cooling lubricant,
e.g. Slugger cutting oil.
Screw the cap onto the coolant container
again.
WARNING
OBJ_BUCH-0000000261-003.book Page 14 Thursday, January 11, 2018 5:30 PM
15
en
Filling the dismounted coolant container
(figure 5)
Pull the empty coolant container out of the
drill stand housing of the magnetic core drill.
Unscrew the cap from the coolant container.
Fill in pump-feedable cooling lubricant,
e.g. Slugger cutting oil.
Screw the cap onto the coolant container
again.
Insert the filled coolant container into the
holder on the drill stand housing intended for
this purpose.
1.
3.
2.
5.
4.
Coolant container
Upper closing cap
max. 500 ml
max. 17 fl. OZ.
Fig. 5
OBJ_BUCH-0000000261-003.book Page 15 Thursday, January 11, 2018 5:30 PM
16
en
Mounting the coolant hose (figure 6).
Connect the coolant hose.
OBJ_BUCH-0000000261-003.book Page 16 Thursday, January 11, 2018 5:30 PM
17
en
Tool changing (figure 7).
Always secure the power tool
with the supplied clamping
strap. In case of a power failure or when the
power plug is pulled, the magnetic holding
power is not maintained.
Switch the machine off and
pull the power plug before
mounting or replacing application tools and
accessories (not overhead!). This preventive
safety measure rules out the danger of injuries
through accidental starting of the power tool.
Core drill bit
Insert the pilot pin into the cutter.
Pull the clamping sleeve of the tool holder
down and insert the core drill bit with the
centering pin into the tool holder.
Do not touch the sharp edges of the core drill
bit. Danger of injury.
Drill chuck
Pull the clamping sleeve of the tool holder
down and insert the drill chuck.
Drill bit
The knurled nut has a left-hand thread; turn
clockwise to release!
Loosen the knurled nut and remove the tool
holder by applying a hammer blow to the
positioned drift.
Clean the inside cone of the output shaft and
insert the drill bit.
WARNING
WARNING
1.
2.
3.
2.
3.
4.
1.
Drill chuck
Clamping sleeve
Centering pin
Core drill bit
JMU 137 MQW
1.
3.
2.
4.
5.
MK 2
MT 2
CM 2
Drill bit
Knurled nut
Fig. 7
OBJ_BUCH-0000000261-003.book Page 17 Thursday, January 11, 2018 5:30 PM
18
en
Working instructions.
Always secure the power tool with the supplied clamping strap. In case of a
power failure or when the power plug is pulled, the magnetic holding power is
not maintained.
Always carry the power tool by its han-
dle, not by the drill-motor cable.
Fastening the safety strap (figure 9).
Always secure the power tool to the work-
piece with the supplied clamping strap.
WARNING
Fig. 8
Clamping strap
Fig. 9
OBJ_BUCH-0000000261-003.book Page 18 Thursday, January 11, 2018 5:30 PM
19
en
For switching the magnet ON
(figure 10).
Pay attention that the set-up surface for the
magnetic foot is flat, clean, rust-free and ice-
free. Remove varnish, putty/filler layers and
other materials. Prevent an air gap between
the magnetic foot and the set-up surface. The
air gap reduces the magnetic holding power.
When working, always use the magnetic foot;
pay attention that the magnetic holding
power is sufficient:
When the green button on the control
panel lights up permanently, the magnetic
holding power is sufficient and the machine
can be operated with normal feed.
When the Magnet button on the control
panel flashes, the magnetic holding power
possibly is insufficient and the machine
must be operated with reduced feed.
When working on materials that are non-fer-
rous, suitable fixation devices obtainable as
accessories from the manufacturer, e. g. suc-
tion plates, vacuum plates or pipe-drilling
devices must be used.
When working on steel materials with a
material thickness of less than 12 mm /
1
/
2
in,
the workpiece must be reinforced with an
additional steel plate in order to guarantee the
magnetic holding power.
Work only with the absolutely required
amount of feed. Excessive feed can lead to
breakage of the application tool and loss of
the magnetic holding power.
The magnetic foot is monitored by means of
a power sensor. If the magnetic foot is defec-
tive, the motor will not start.
When the power supply is disconnected
while the motor is running, a protective cir-
cuit prevents automatic restarting of the
motor. Restart the motor again. Adjust the
gear setting only when the machine is at a
complete stop or when the motor is running
down. Do not stop the drill motor during the
drilling procedure. Remove the core drill bit
from the drill hole only while the drill motor
is running. If the core drill bit gets jammed/
stuck in the material, stop the drill motor and
carefully rotate out the core drill bit turning in
counterclockwise direction. After each drill-
ing run, remove the chips and the drilled out
core. Do not touch the chips with your bare
hands. Always use a chip hook. Danger of
burning! The surface of the magnet can reach
high temperatures. Do not touch the magnet
with your bare hands. When changing a drill
bit, pay attention not to damage the cutting
edges. When core-drilling layered material,
remove the core and the chips after having
drilled through each layer. Do not use the
magnetic core drill unit when the cooling-
lubricant system is defective. Check for tight-
ness against leaks and for cracks in the hoses.
Prevent liquids from entering or penetrating
electrical components. The core drill units do
not have overload protection. In case of
improper use, the motor can become dam-
aged.
=
Switches the magnet On/Off
=
Switches the magnet On/Off
Fig. 10
> 12 mm
< 12 mm
> 12 mm
< 12 mm
OBJ_BUCH-0000000261-003.book Page 19 Thursday, January 11, 2018 5:30 PM
20
en
Adjusting the stroke range (figure 11).
Hold the power tool firmly
with one hand when releasing
the two fastening levers.
To move the fastening levers over each other,
pull a fastening lever outward and then turn
the fastening lever in 45° steps.
Loosen both fastening levers with the other
hand.
Adjust the desired stroke range.
Tighten both fastening levers again.
CAUTION
1.
2.
2.
3.
1.
4.
4.
2.
2.
1.
3.
4.
4.
2.
2.
Fig. 11
OBJ_BUCH-0000000261-003.book Page 20 Thursday, January 11, 2018 5:30 PM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80

FEIN JMU 137-2 QW Manuel utilisateur

Catégorie
Outils électroportatifs
Taper
Manuel utilisateur

dans d''autres langues