Hangar 9 HAN2365 Le manuel du propriétaire

Marque: Hangar 9

Modèle: HAN2365

Catégorie: Jouets télécommandés

Taper: Le manuel du propriétaire

Ce manuel convient également à

HANGAR 9 Ultra Stick 30cc

Ultra Stick

™

30cc

Instruction Manual

Bedienungsanleitung

Manuel d’utilisation

Manuale di Istruzioni

 SPECIFICATIONS • SPEZIFIKATIONEN • SPÉCIFICATIONS • SPECIFICHE  LARGE PARTS LAYOUT • BAUTEILE (OHNE KLEINTEILE) • GRANDES PIÈCES • SCHEMA DEI COMPONENTI GRANDI

81.0 in (206 cm)

1360 sq in (87.8 dm2) Total/Totale

73 in (185 cm)

12–14 lbs (5.4–6.35 kg)

2-Stroke Gas: 30cc, 4-Stroke gas/petrol: 36cc

2-Takt Benziner: 30cc, 4-Takt Benzin: 36cc

2 temps Essence: 30cc, 4 temps essence: 36cc

2-Tempi Gas: 30cc, 4 tempi benzina: 36 cc

Electric Power Power: Power 160 Brushless

Elektro Antrieb Power: Power 160 Brushless

Moteur électrique (EP): Power 160 Brushless

Motore elettrico: Power 160 Brushless

5-channel (or greater) with 8 servos

5-Kanal (oder größer) mit 8-Servos

5 voies (ou plus) avec 8 servos

a 5 canali (o più) con 8 servo

Spinner (not included): 3-inch

Spinner (nicht im Lieferumfang enthalten): 75mm

Cône (non inclus): 75mm

Ogiva dell’elica (non inclusa): 75mm

Ultra Stick

™

30cc

Part # English Deutsch Français Italiano

 REPLACEMENT PARTS • ERSATZTEILE • PIÈCES DE RECHANGE • PEZZI DI RICAMBIO

1 HAN236501 Fuselage Rumpf Fuselage Fusoliera

2 HAN236502 Left Wing with Aileron and Flap Tragﬂ äche Links mit Querruder und Klappe Aile gauche avec aileron et volet Semiala sinistra con alettone e ﬂ ap

3 HAN236503 Right Wing with Aileron and Flap Tragﬂ äche Rechts mit Querruder und Klappe Aile droite avec aileron et volet Semiala destra con alettone e ﬂ ap

4 HAN236504 Vertical Stabilizer with Rudder Vertikaler Stabilisator mit Seitenruder Stabilisateur vertical avec dérive Stabilizzatore verticale con direzionale

5 HAN236505 Horizontal Stabilizer with Elevators Horizontaler Stabilisator mit Höhenruder Stabilisateur horizontal avec profondeur Stabilizzatore orizzontale con elevatori

6 HAN236506 Wing Tube (1.25 inch) Tragﬂ ächenverbinder (1.25 inch) Clé d’aile (1.25 inch) Tubo dell’ala (1.25 inch)

7 HAN236507 Landing Gear Set Fahrwerk Set Train d’atterrissage Set del carrello di atterraggio

8 HAN236508 Wheel Pants Radverkleidung Carénage de roue Copriruote

9 HAN236509 Aileron and Flap (LH) Querruder und Klappe (LH) Aileron et volet (côté gauche) Alettone e ﬂ ap sinistro

10 HAN236510 Aileron and Flap (RH) Querruder und Klappe (RH) Aileron et volet (côté droit) Alettone e ﬂ ap destro

11 HAN236511 Hardware Set Kleinteile Set Sachet de visserie Set dei pezzi

12 HAN236513 Fuselage Hatch Rumpfklappe Capot du fuselage Portello della fusoliera

13 HAN236514 Wheel Set: Reifensatz Roues Set ruote

14 HAN236515 EP Battery Tray EP-Akkuhalterung Platine moteur électrique Portabatteria per motore elettrico

15 HAN236516 Pushrod Set Gestänge / Anlenkungen Set Jeu de tringleries Set dell’asta di spinta

16 HAN236517 Tail Wheel Assembly Spornrad m. Zbh. Assemblage de roulette de queue Gruppo del ruotino di coda

17 HAN236518 Fuel Tank 15oz (450cc) Kraftstoffmotor 450cc (15oz) Réservoir carburant 450cc (15oz) Serbatoio carburante 450 cc

 SMALL PARTS (NOT SHOWN)•KLEINTEILE (NICHT ABGEBILDET)•PETITES PIÈCES (NON REPRÉSENTÉES)•PARTI DI PICCOLE DIMENSIONI (NON MOSTRATE)

HAN236512 Decal Set Dekorbogen Planche de décoration Set di decalcomanie

 OPTIONAL ITEMS • OPTIONALE TEILE • ÉLÉMENTS OPTIONNELS • ARTICOLI OPZIONALI

EVOA118 Engine Soft-Mount Kit 20-40cc (10-32) Weicher Motor-Halterungssatz 20-40cc (10-32) Support moteur sur silent block 20-40cc (10-32) Kit supporto motore morbido 20-40 cc (10-32)

SPMAR6210

AR6210 6-Channel DSMX

Receiver

AR6210 6 Kanal DSMX®-Empfänger Récepteur Spektrum AR6210 6 voies DSMX Ricevente AR6210 DSMX® 6 canali

SPMAR636 AR636 6-Channel AS3X Sport Receiver AR636 6 Kanal AS3X-Sportempfänger Récepteur Spektrum AR636 6 voies AS3X Ricevente sport AR636 AS3X 6 canali

SPMAR7350

AR7350 7 Channel AS3X RX with integrated

telemetry

AR7350 7 Kanal AS3X RX mit integrierter Telemetrie

Récepteur Spektrum AR7350 7 voies AS3X avec

télémétrie intégrée

Ricevente AR7350 AS3X 7 canali con telemetria

integrata

SPMAR7610 AR7610 7-Channel DSMX Hi Speed Receiver AR7610 7-Kanal DSMX HiSpeed Empfänger

Récepteur Spektrum AR7610 7 voies DSMX haute

vitesse

Ricevente Hi Speed AR7610 DSMX 7 canali

SPMAR8000 AR8000 8-Channel DSMX Receiver AR8000 8 Kanal DSMX-Empfänger Récepteur Spektrum AR8000 8 voies DSMX Ricevente AR8000 DSMX 8 canali

SPMAR9110 AR9110 9-Channel DSMX PowerSafe Receiver AR9110 9 Kanal DSMX PowerSafe-Empfänger Récepteur Spektrum AR9110 9 voies DSMX PowerSafe Ricevente PowerSafe AR9110 DSMX 9 canali

WGT201

Extreme Little Tote Double 42”x22”x14” Red/

Black

Extreme Little Tote Double 42” x 22” x 14” Red/Black

Sac de transport pour ailes Extreme Little Tote Double

106 x 55 x 35cm Rouge/Noir

Extreme Little Tote Double 42” x 22” x 14” rosso/

nero

HAN9151 x3

Aluminum Servo Arm, 1-inch: SPM, JR

(For Rudder and Elevator 3D control throw)

Aluminium-Servoarm, 250mm (1 Zoll): SPM,JR

(Für Seitenruder und Höhenruder 3D-Ruderausschlag)

Palonnier servo aluminium 25,4mm: SPM, JR

(Pour débattements dérive et profondeur 3D)

Squadretta servo alluminio, 1'': SPM, JR

(per escursione 3D dei comandi direzionale ed

elevatore)

SPMSA6265 x7

A6265 HV Digital Hi-Torque MG Aircraft Servo

(For Extreme 3D ﬂ ying)

A6265 HV Digitaler Hi-Torque MG Flugzeugservo (für

extremen 3D-Flug)

Servo digital A6265 HV couplé élevé, pignons métal

pour avion (Pour vol 3D extrême)

Servo digitale MG alto voltaggio alta coppia

A6265 (per volo 3D estremo)

Part # English Deutsch Français Italiano

 REQUIRED RADIO EQUIPMENT • ERFORDERLICHE RC AUSRÜSTUNG • ÉQUIPEMENT RADIO REQUIS • APPARECCHIATURE RADIO NECESSARIE

SPMAR9350

AR9350 9-Channel AS3X

Receiver

Spektrum AR9350 9-Kanal AS3X-Empfänger Récepteur AR9350 9 voies AS3X Ricevente AR9350 9-canali AS3X

SPMB2200LFRX 6.6V 2200mAh 2S LiFe Receiver Battery 2200mA 2S 6,6V LiFe Empfänger-Akku Batterie récepteur Li-Fe 2S 6,6V 2200mA Batteria LiFe per ricevente 2S 6,6 V 2200 mAh

EVOA112

Evolution

3 Wire Ignition/Rx Switch

Evolution Zündschalter Interrupteur Evolution 3 ﬁ ls Allumage/RX

Evolution, interruttore a 3 ﬁ li accensione/

ricevitore

SPMSA6180 x8 A6180 Digital Aircraft Servo A6180 Digitaler Flugzeugservo Servo digital AR6180 pour avion Servo digitale A6180

HAN9154 x4

Aluminum Servo Arm, 1.5-inch: SPM, JR

(Ailerons and Flaps, Standard Throw)

Aluminium-Servoarm, 38mm: SPM,JR

(Querruder und Landeklappen, Standard-Ausschlag)

Palonnier servo aluminium 38mm: SPM, JR

(Ailerons et Volets, Débattements Standards)

Squadretta servo alluminio, 38 mm: SPM, JR

(Alettoni e ﬂ ap, escursione standard)

HAN9160 x4

Aluminum Servo Arm, 2-inch (JR/SPM)

(Ailerons and Flaps, Extreme Throw)

Hangar 9 Aluminium Servo Arm, 50 mm (JR/SPM)

(Querruder und Landeklappen, Extremer Ausschlag)

Palonnier de servo en aluminium, long 50mm (JR,SPM)

(Ailerons et Volets, Débattements Extrêmes)

Squadretta servo in alluminio 50 mm (JR/SPM)

(Alettoni e ﬂ ap, escursione estrema)

DUB671 x2

Super Strength Long Servo Arm (JR)

(Elevator and Rudder)

Superstärke Servoarm, lang (JR)

(Höhenruder und Seitenruder)

Palonnier de servo super résistant, long (JR)

(Profondeur et dérive)

Squadretta servo super resistente, lungo (JR)

(elevatore e direzionale)

SPMA3001 x4 Heavy-Duty Servo Extension 6-inch Schwerlast-Servoverlängerung 150 mm (6 Zoll) Rallonge de servo, 150 mm Prolunga servo 150 mm

SPMA3003 x2

Heavy Duty Servo Extension 12-inch

(Ailerons)

Schwerlast-Servoverlängerung 300 mm (12 Zoll)

(Querruder)

Rallonge de servo, 300 mm

(Ailerons)

Prolunga servo 300 mm

(Alettoni)

SPMA3004 x2

(Optional)

Heavy Duty Servo Extension 18-inch

(Optional Elevator servo installation)

Schwerlast-Servoverlängerung 460mm (18 Zoll)

(Montage des Höhenruderservo optional)

Rallonge de servo, 460 mm

(Installation du servo de profondeur optionnel)

Prolunga servo 460 mm

(Installazione servo elevatore opzionale)

SPMA3054 Servo Connector Clips (25) Servosteckerklemmen (25) Clips pour connecteur de servo (25) Clips connettori servi (25)

 2-STROKE GAS • 2-TAKT BENZINER • 2 TEMPS ESSENCE • 2-TEMPI A BENZINA

EVOE33GX 33GX 33cc (2.00 cu. in.) Gas Engine 33GX 33cc (2,00 Kubikzoll) Kraftstoffmotor Moteur essence Evolution 33GX 33cc (2.00) Motore a benzina 33GX 33 cc

APC17080 17 x 8 Propeller 17 x 8 Propeller Hélice 17 x 8 17 x 8 Elica

HAN116 Fuel Filler with “T” and Overﬂ ow Fittings Tanknippel mit T-Stück u. Überlauf Fitting Point de remplissage de carburant avec coupleur en T Riempitore carburante con “T” e raccordi troppo

EVOM3 Pitts-style Mufﬂ er, Single Pipe: 33GX Pitts-artiger Schalldämpfer, Einzelrohr: 33GX 33GX - Silencieux Pitts simple sortie Scarico stile Pitts, tubo singolo: 33GX

EVOM4 Pitts-style Mufﬂ er, Dual Pipe: 33GX Pitts-artiger Schalldämpfer, Doppelrohr: 33GX 33GX - Silencieux Pitts double sortie Scarico stile Pitts, doppio tubo: 33GX

SPMB2200LFRX 6.6V 2200mAh 2S LiFe Receiver Battery 2200mA 2S 6,6V LiFe Empfänger-Akku Batterie récepteur Li-Fe 2S 6,6V 2200mA Batteria LiFe per ricevente 2S 6,6 V 2200 mAh

SPMA3001 Heavy Duty Servo Extension 6-inch Schwerlast-Servoverlängerung 150mm (6 Zoll) Rallonge de servo, 150 mm Prolunga servo 150 mm

EVOA112 Evolution 3 Wire Ignition/Rx Switch Evolution Zündschalter Interrupteur Evolution 3 ﬁ ls Allumage/RX

Evolution, interruttore a 3 ﬁ li accensione/

ricevitore

EVOA100 Optical Ignition Kill Switch (Optional) Optischer Zünd-Notausschalter (optional)

Interrupteur optique coupe circuit d'allumage

(optionnel)

Kill switch ottico per avviamento (opzionale)

HAN502016

3-inch 2-Blade Aluminum Spinner:

Cirrus SR22T 30cc

76mm (3 Zoll) Aluminium-Spinner mit 2 Blättern:

Cirrus SR22T 30cc

Cirrus SR20 - Cône en aluminium 3" bipale Ogiva bipala alluminio 3'': Cirrus SR22T 30 cc

Ultra Stick

™

30cc

Part # English Deutsch Français Italiano

 ELECTRIC POWER • ELEKTROANTRIEB • MOTEUR ELECTRIQUE (EP) • MOTORE ELETTRICO

EFLM4160A Power 160 Brushless Outrunner Motor, 245Kv Bürstenloser Außenläufer-Motor Leistung 160, 245Kv

Moteur à cage tournante sans balais Power 160 de

245Kv

Motore brushless a cassa rotante Power 160,

245Kv

CSE010010400 Phoenix Edge 120HV, 50V 120-Amp ESC

Phoenix Edge 120HV, 50V 120 A

Geschwindigkeitsregler

Contrôleur Phoenix Edge 120HV, 50V 120A ESC Phoenix Edge 120HV, 50 V 120 A

CSE010000401 Castle BEC PRO V2, 010-0004-01 (Optional) Castle BEC PRO V2, 010-0004-01 (optional) Castle BEC PRO V2, 010-0004-01 (optionnel) BEC Castle PRO V2, 010-0004-01 (opzionale)

EFLB50005S30

5000mAh 5S 18.5V 30C LiPo Battery,12AWG

EC3

™

5000 mA 5S 18,5V 30C LiPo-Akku,12AWG EC3

Batterie Li-Po 5S 18,5V 5000mA 30C, 12AWG prise

EC3

Batteria LiPo 30C 18,5 V 5S 5000 mAh,12AWG

EC3

KXSB0026

5000mAh 5S 18.5V 30C LiPo Battery, 10AWG:

EC5

™

5000 mA 5S 18,5V 30C LiPo-Akku,10AWG EC5

Batterie Li-Po 5S 18,5V 5000mA 30C, 10AWG prise

EC5

Batteria LiPo 30C 18,5 V 5S 5000 mAh,10AWG

EC5

APC18010E Thin Electric Propeller, 18 x 10 Elektro Propeller, 18 x 10 Hélice électrique, 18 x 10 Elica elettrica sottile, 18 x 10

HAN502016

3-inch 2-Blade Aluminum Spinner:

Cirrus SR22T 30cc

76mm (3 Zoll) Aluminium-Spinner mit 2 Blättern:

Cirrus SR22T 30cc

Cirrus SR20 - Cône en aluminium 3" bipale Ogiva bipala alluminio 3'': Cirrus SR22T 30 cc

 OPTIONAL FLOATS•OPTIONALE SCHWIMMER•FLOTTEURS OPTIONNELS•GALLEGGIANTI OPZIONALI

HAN6030 1/5-Scale Float Set Schwimmersatz im Maßstab 1/5 Set de ﬂ otteurs 1/5 Set galleggianti scala 1:5

HAN236519 Float Strut Set: Ultra Stick 30cc Schwimmerverstrebungssatz: Ultra Stick 30cc Ultra Stick 30cc – Haubans de ﬂ otteurs Set supporti galleggianti: Ultra Stick 30cc

SPMSA4030 x2

A4030 Micro HV Digital Hi-Torque MG Aircraft

Servo

A4030 Micro HV Digitaler Hi-Torque MG Flugzeugservo

Micro servo digital AR4030 HV couple élevé à pignons

métal pour avion

Servo micro digitale A4030 alto voltaggio alta

coppia

SPMA3058 Standard Y-Harness, 6-inch Standard Y-Kabelbaum, 152mm (6 Zoll) Rallonge Y standard, 15cm Cavo a Y standard, 6''

SPMA3004 x2 Heavy Duty Servo Extension 18-inch Schwerlast-Servoverlängerung 460mm (18 Zoll) Rallonge de servo, 460 mm Prolunga servo 460 mm

Part # English Deutsch Français Italiano

 REQUIRED ADHESIVES • ERFORDERLICHE KLEBSTOFFE • TYPES DE COLLES • ADESIVI NECESSARI

DLMAD44 Roket Rapid CA 5-10 sec: 20g Roket Rapid CA 5-10 s: 20g Colle cyano Roket Rapid 5-10 sec: 20g Colla cianoacrilica Roket Rapid 5-10 sec: 20 g

DLMAD45 Roket Max CA 10-20 sec: 20g Roket Max CA 10-20 s: 20g Colle cyano Roket Max 10-20 sec: 20g Colla cianoacrilica Roket Max 10-20 sec: 20 g

PAAPT715 CA Accelerator Sekundenkleber (CA) Aktivator Accélérateur de colle CA Accelerante colla CA

PAAPT35 15-Minute Epoxy 15 Minuten Epoxy Époxy 15 minutes Colla epoxy 15 minuti

PAAPT42 Threadlock Schraubensicherungslack Frein-ﬁ let Frenaﬁ letti

DLMAD12 R/C Modeller Canopy Glue: 4 oz R/C Modeller Kanzelkleber: 113,4g (4 oz) Colle à verrière R/C Modeller: 113g Colla per capottine R/C Modeller: 4 oz

 REQUIRED TOOLS • BENÖTIGTES WERKZEUG • OUTILS REQUIS • ATTREZZI NECESSARI

Box wrench: 1/2-inch Ringschlüssel: 1/2-inch Clé hexagonale: 1/2-inch Chiave esagonale: 1/2-inch

Drill Bohrer Mini-perceuse Trapano

Drill bit: 1/16-inch, 5/64-inch, 1/8-inch

5/32-inch, 3/16-inch

Bohrer: 1,5mm, 2mm, 3mm, 4mm, 4,5mm Forêt : 1,5mm, 2mm, 3mm, 4mm, 4,5mm

Punte per trapano: 1,5mm, 2mm, 3mm, 4mm,

4,5mm

Felt-tipped pen Faserstift Feutre ﬁ n effaçable Pennarello

Epoxy brush Pinsel Pinceau Epoxy Spazzole epoxy

Flat ﬁ le Flachfeile Lime plate Lima piatta

Hemostats Klemme Pince Hemostat Pinzetta

Hex wrench: 3/32-inch, 1.5mm, 2mm, 2.5mm,

3mm, 4mm

Inbusschlüssel: 3/32-inch, 1,5mm, 2mm, 2,5mm,

3mm, 4mm

Tournevis hexagonal: 3/32-inch, 1,5mm, 2mm, 2,5mm,

3mm, 4mm

Chiave esag.: 3/32-inch, 1,5mm, 2mm, 2,5mm,

3mm, 4mm

Hobby knife with #11 blade Hobbymesser mit # 11 Klinge Couteau : Lame numéro 11 Taglierino: #11 lama

Isoplrpyl alcohol Isopropyl Alkohol Alcool isopropylique Alcol isopropilico

Low-tack tape Kreppband Adhésif de masquage Nastro a bassa aderenza

Needle nose pliers Spitzzange Pince ﬁ ne Pinze a becco stretto

Nut driver: 1/4-inch, 4mm, 5.5mm Steckschlüssel. 1/4-inch, 11/32-inch Clés à douilles : 1/4-inch, 11/32 pouce Chiave per dadi: 1/4-inch, 11/32-inch

Paper towels Papiertücher Papier absorbant Asciugamani di carta

Pencil Stift Crayon à papier Matita

Phillips screwdriver: #1 Phillips Schraubendreher: #1 Tournevis cruciforme: #1 Cacciavite a croce: #1

Pin vise Handbohrer Porte forets Trapano manuale

Pliers Zange Pince Pinze

Ruler Lineal Réglet Righello

Sandpaper Schleifpapier Papier de verre Carta vetrata

Scissors Schere Ciseaux Forbici

Side cutters Seitenschneider Pince coupante Lama laterale

Square Geodreieck Équerre Squadra

Tap and drill set, English Gewindeschneider und Bohrerset Taraud et foret Set punte e maschi, Inglese

Tap Handle Halter für Gewindeschneider Épingles Impugnatura per maschiare

T-pins T- Nadeln Epingles Spilli a T

Toothpicks Zahnstocher Cure dents Stuzzicadenti

Ultra Stick

™

30cc

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon

Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.

The following terms are used throughout the product literature to indicate various levels of potential harm when

operating this product:

Meaning of Special Language

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or

no possibility of injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a

possibility of serious injury.

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage,

and serious injury OR create a high probability of superﬁ cial injury.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating.

Failure to operate the product correctly can result in damage to the product, personal property and cause serious

injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic

mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage

to the product or other property. This product is not intended for use by children without direct adult supervision. Do

not attempt disassembly, use with incompatible components or augment product in any way without the approval

of Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to

read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate

correctly and avoid damage or serious injury.

AGE RECOMMENDATION: NOT FOR CHILDREN UNDER 14 YEARS. THIS IS NOT A TOY.

 USING THE MANUAL

This manual is divided into sections to help make assembly easier to understand.

 SAFETY WARNINGS AND PRECAUTIONS

Read and follow all instructions and safety precautions before use. Improper use can result in ﬁ re, serious injury and

damage to property.

Components

Use only with compatible components. Should any compatibility questions exist, please refer to the product

instructions, component instructions or contact the appropriate Horizon Hobby ofﬁ ce.

Flight

Fly only in open areas to ensure safety. It is recommended ﬂ ying be done at radio control ﬂ ying ﬁ elds. Consult local

ordinances before choosing a ﬂ ying location.

Propeller

Keep loose items that can become entangled in the propeller away from the prop. This includes loose clothing or other

objects such as pencils and screwdrivers. Keep your hands away from the propeller as injury can occur.

Batteries

Always follow the manufacturer’s instructions when using and disposing of any batteries. Mishandling of Li-Po

batteries can result in ﬁ re causing serious injury and damage.

Small Parts

This kit includes small parts and should not be left unattended near children as choking and serious injury could result.

 SAFE OPERATING RECOMMENDATIONS

• Inspect your model before every ﬂ ight to ensure it is airworthy.

• Be aware of any other radio frequency user who may present an interference problem.

• Always be courteous and respectful of other users in your selected ﬂ ight area.

• Choose an area clear of obstacles and large enough to safely accomodate your ﬂ ying activity.

• Make sure this area is clear of friends and spectators prior to launching your aircraft.

• Be aware of other activities in the vicinity of your ﬂ ight path that could cause potential conﬂ ict.

• Carefully plan your ﬂ ight path prior to launch.

• Abide by any and all established AMA National Model Aircraft Safety Code.

 BEFORE STARTING ASSEMBLY

• Remove parts from bag.

• Inspect fuselage, wing panels, rudder and stabilizer for damage.

• If you ﬁ nd damaged or missing parts, contact your place of purchase.

If you ﬁ nd any wrinkles in the covering, use a heat gun (HAN100) and covering glove (HAN150) or covering iron

(HAN101) with a sealing iron sock (HAN141) to remove them. Use caution while working around areas where the colors

overlap to prevent separating the colors.

• Charge transmitter and receiver batteries.

• Center trims and sticks on your transmitter.

• For a computer radio, create a model memory for this particular model.

• Bind your transmitter and receiver, using your radio system’s instructions.

IMPORTANT: Rebind the radio system once all control throws are set. This will keep the servos from moving to

their endpoints until the transmitter and receiver connect. It will also guarantee the servo reversal settings are

saved in the radio system.

Propeller

Halten Sie lose Gegenstände die sich im Propeller verfangen können weg vom Propeller. Dieses gilt auch für Kleidung

oder andere Objekte wie zum Beispiel Stifte oder Schraubendreher.

Halten Sie ihre Hände weg vom Propeller, es besteht akute Verletzungsgefahr.

Akkus

Folgen Sie immer den Herstelleranweisungen bei dem Gebrauch oder Entsorgung von Akkus. Falsche Behandlung von

LiPo Akkus kann zu Feuer mit Körperverletzungen und Sachbeschädigung führen.

Kleinteile

Dieser Baukasten beinhaltet Kleinteile und darf nicht unbeobachtet in der Nähe von Kindern gelassen werden, da die

Teile verschluckt werden könnten mit ernsthaften Verletzung zur Folge.

 EMPFEHLUNGEN ZUM SICHEREN BETRIEB

• Überprüfen Sie zur Flugtauglichkeit ihr Modell vor jedem Flug.

• Beachten Sie andere Piloten deren Sendefrequenzen ihre Frequenz stören könnte.

• Begegnen Sie anderen Piloten in ihrem Fluggebiet immer höﬂ ich und respektvoll.

• Wählen Sie ein Fluggebiet, dass frei von Hindernissen und groß genug ist.

• Stellen Sie vor dem Start sicher, dass die Fläche frei von Freunden und Zuschauern ist.

• Beobachten Sie den Luftraum und andere Flugzeuge/Objekte die ihren Flugweg kreuzen und zu einem Konﬂ ikt

führen könnten.

• Planen Sie sorgfältig ihren Flugweg vor dem Start.

 VOR DEM ZUSAMMENBAU

• Entnehmen Sie zur Überprüfung jedes Teil der Verpackung.

• Überprüfen Sie den Rumpf, Tragﬂ ächen, Seiten- und Höhenruder auf Beschädigung.

• Sollten Sie beschädigte oder fehlende Teile feststellen, kontaktieren Sie bitte den Verkäufer.

Zum Entfernen von Falten in der Bespannung verwenden Sie den Heißluftfön (HAN100) und Bespannhandschuh

(HAN150) oder das Folienbügeleisen (HAN141). Bitte achten Sie bei überlappenden Farben, dass Sie diese sich bei

dem Bearbeitung nicht trennen.

• Laden des Senders und Empfängers.

• Zentrieren der Trimmungen und Sticks auf dem Sender.

• Sollten Sie einen Computersender verwenden, resetten Sie einen Speicherplatz und benennen ihn nach dem Modell.

• Sender und Empfänger jetzt nach den Bindeanweisung des Herstellers zu binden.

WICHTIG: Wir empfehlen dringend nachdem alle Einstellungen vorgenommen worden sind, das Modell neu zu binden.

Dieses verhindert, dass die Servos in die Endanschläge laufen bevor sich Sender und Empfänger verbunden haben. Es

garantiert auch, dass die Servoreverseeinstellungen in der RC Anlage gesichert sind.

HINWEIS

Alle Anweisungen, Garantien und anderen zugehörigen Dokumente können im eigenen Ermessen von Horizon Hobby,

LLC. jederzeit geändert werden Die aktuelle Produktliteratur ﬁ nden Sie auf horizonhobby.com unter der Registerkarte

„Support“ für das betreffende Produkt.

Spezielle Bedeutungen

Die folgenden Begriffe werden in der gesamten Produktliteratur verwendet, um auf unterschiedlich hohe

Gefahrenrisiken beim Betrieb dieses Produkts hinzuweisen:

HINWEIS: Wenn diese Verfahren nicht korrekt befolgt werden, können sich möglicherweise Sachschäden UND geringe

oder keine Gefahr von Verletzungen ergeben.

ACHTUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich wahrscheinlich Sachschäden UND die

Gefahr von schweren Verletzungen.

WARNUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich wahrscheinlich Sachschäden,

Kollateralschäden und schwere Verletzungen ODER mit hoher Wahrscheinlichkeit oberﬂ ächliche Verletzungen.

WARNUNG: Lesen Sie die GESAMTE Bedienungsanleitung, um sich vor dem Betrieb mit den Produktfunktionen

vertraut zu machen. Wird das Produkt nicht korrekt betrieben, kann dies zu Schäden am Produkt oder persönlichem

Eigentum führen oder schwere Verletzungen verursachen.

Dies ist ein hochentwickeltes Hobby-Produkt. Es muss mit Vorsicht und gesundem Menschenverstand betrieben

werden und benötigt gewisse mechanische Grundfähigkeiten. Wird dieses Produkt nicht auf eine sichere und

verantwortungsvolle Weise betrieben, kann dies zu Verletzungen oder Schäden am Produkt oder anderen Sachwerten

führen. Dieses Produkt eignet sich nicht für die Verwendung durch Kinder ohne direkte Überwachung eines

Erwachsenen. Verwenden Sie das Produkt nicht mit inkompatiblen Komponenten oder verändern es in jedweder Art

ausserhalb der von Horizon Hobby, LLC vorgegebenen Anweisungen. Diese Bedienungsanleitung enthält Anweisungen

für Sicherheit, Betrieb und Wartung. Es ist unbedingt notwendig, vor Zusammenbau, Einrichtung oder Verwendung

alle Anweisungen und Warnhinweise im Handbuch zu lesen und zu befolgen, damit es bestimmungsgemäß betrieben

werden kann und Schäden oder schwere Verletzungen vermieden werden.

NICHT GEEIGNET FÜR KINDER UNTER 14 JAHREN. DIES IST KEIN SPIELZEUG.

 ÜBER DIESE ANLEITUNG

Diese Anleitung ist zur Vereinfachung des Zusammenbaues in Sektionen unterteilt.

 WARNUNGEN UND SICHERHEITS-VORKEHRUNGEN

Bitte lesen und befolgen Sie alle Anweisungen und Sicherheitsvorkehrungen vor dem Gebrauch. Falscher, nicht

sachgemäßer Gebrauch kann Feuer, ernsthafte Verletzungen und Sachbeschädigungen zur Folge haben.

Komponenten

Verwenden Sie mit dem Produkt nur kompatible Komponenten. Sollten Fragen zur Kompatibilität auftreten, lesen Sie

bitte die Produkt- oder Bedienungsanweisung oder kontaktieren den Service von Horizon Hobby.

Fliegen

Fliegen Sie um Sicherheit garantieren zu können, nur in weiten offenen Gegenden. Wir empfehlen hier den Betrieb auf

zugelassenen Modellﬂ ugplätzen. Bitte beachten Sie lokale Vorschriften und Gesetze, bevor Sie einen Platz zum Fliegen

wählen.

Ultra Stick

™

30cc

L’hélice

Gardez éloignés tous les éléments qui pourraient être attrapés par l’hélice. Cela inclut les vêtements larges ou les

objets comme des outils par exemple. Gardez toujours vos mains à distance pour éviter tout cas de blessures.

Les batteries

Suivez toujours les instructions du fabricant de vos batteries. Une mauvaise manipulation d’une batterie Li-Po peut

entraîner un incendie causant de graves dégâts matériels et des blessures corporelles.

Petites pièces

Ce kit contient des petites pièces qui ne doivent pas être laissées à la portée des enfants, ces pièces sont dangereuses

pour eux et peuvent entraîner de graves blessures.

 CONSIGNES DE SÉCURITÉ CONCERNANT L’UTILISATION

• Inspectez votre modèle avant chaque vol.

• Surveillez les fréquences utilisées à proximité.

• Soyez toujours courtois et respectueux des autres utilisateurs de la zone de vol.

• Choisissez une zone dégagée de tout obstacle et sufﬁ samment grande pour voler en toute sécurité.

• Contrôlez que la zone est libre de spectateurs avant de lancer votre modèle.

• Soyez conscient des autres activités aux alentours de votre vol, risque de conﬂ it potentiel.

• Planiﬁ ez votre vol avant de le commencer.

 AVANT DE COMMENCER L’ASSEMBLAGE

• Retirez toutes les pièces des sachets pour les inspecter.

• Inspectez soigneusement le fuselage, les ailes et les empennages.

• Si un élément est endommagé, contactez votre revendeur.

Si l’entoilage présente quelque plis, vous pouvez les lisser en utilisant le pistolet à air chaud (HAN100) et le gant

(HAN150) ou le fer à entoiler (HAN101) avec la chaussette de protection (HAN141). Agissez soigneusement dans les

zones où plusieurs couleurs d’entoilage sont superposées aﬁ n d’éviter de les séparer.

• ll est recommandé de préparer tous les éléments du système de la radio.

• Cela inclut la charge des batteries comme la mise au neutre des trims et des manches de votre émetteur.

• Si vous utilisez une radio programmable, sélectionnez une mémoire libre aﬁ n d’y enregistrer les paramètres de ce

modèle.

• Nous vous recommandons d’affecter maintenant le récepteur à l’émetteur en suivant les instructions fournies avec

votre radio.

IMPORTANT: Il est hautement recommandé de ré-affecter le système une fois que les courses seront réglées. Cela

empêchera les servos d’aller en butée lors de la connexion du système. Cela garantit également que la direction des

servos est enregistrée dans l’émetteur.

REMARQUE

La totalité des instructions, garanties et autres documents est sujette à modiﬁ cation à la seule discrétion d’Horizon

Hobby, LLC. Pour obtenir la documentation àjour, rendez-vous sur le site horizonhobby.com et cliquez sur l’onglet de

support de ce produit.

Signiﬁ cation de certains termes spéciﬁ ques

Les termes suivants sont utilisés dans l’ensemble du manuel pour indiquer différents niveaux de danger lors de

l’utilisation de ce produit:

REMARQUE: Procédures qui, si elles ne sont pas suivies correctement, peuvent entraîner des dégâts matériels ET

éventuellement un faible risque de blessures.

ATTENTION: Procédures qui, si elles ne sont pas suivies correctement, peuvent entraîner des dégâts matériels ET des

blessures graves.

AVERTISSEMENT: Procédures qui, si elles ne sont pas suivies correctement, peuvent entraîner des dégâts matériels

et des blessures graves OU engendrer une probabilité élevée de blessure superﬁ cielle.

AVERTISSEMENT: Lisez la TOTALITÉ du manuel d’utilisation aﬁ n de vous familiariser avec les caractéristiques du

produit avant de le faire fonctionner. Une utilisation incorrecte du produit peut entraîner sa détérioration, ainsi que des

risques de dégâts matériels, voire de blessures graves.

Ceci est un produit de loisirs sophistiqué. Il doit être manipulé avec prudence et bon sens et requiert des aptitudes

de base en mécanique. Toute utilisation irresponsable de ce produit ne respectant pas les principes de sécurité peut

provoquer des blessures, entraîner des dégâts matériels et endommager le produit. Ce produit n’est pas destiné à

être utilisé par des enfants sans la surveillance directe d’un adulte. N’essayez pas de modiﬁ er ou d’utiliser ce produit

avec des composants incompatibles hors des instructions fournies par Horizon Hobby, LLC. Ce manuel comporte des

instructions relatives à la sécurité, au fonctionnement et à l’entretien. Il est capital de lire et de respecter la totalité

des instructions et avertissements du manuel avant l’assemblage, le réglage et l’utilisation, ceci aﬁ n de manipuler

correctement l’appareil et d’éviter tout dégât matériel ou toute blessure grave.

14 ANS ET PLUS. CECI N’EST PAS UN JOUET.

 UTILISATION DU MANUEL

Ce manuel est divisé en sections pour vous aider à comprendre plus facilement l’assemblage.

 AVERTISSEMENTS RELATIFS À LA SÉCURITÉ

Lisez et suivez toutes les instructions relatives à la sécurité avant utilisation. Une utilisation inappropriée peut entraîner

un incendie, de graves blessures et des dégâts matériels.

Composants

Utilisez uniquement des composants compatibles. Si vous avez des questions concernant la compatibilité, référez-vous

à ce manuel ou contactez le service technique Horizon Hobby.

Le vol

Volez uniquement dans des zones dégagées pour un maximum de sécurité. Il est recommandé d’utiliser les pistes des

clubs d’aéromodélisme. Consultez votre mairie pour connaître les sites autorisés.

AVVISO

Tutte le istruzioni, le garanzie e gli altri documenti pertinenti sono soggetti a cambiamenti a totale discrezione di

Horizon Hobby, LLC. Per una documentazione aggiornata sul prodotto, visitare il sito www.horizonhobby.com e fare

clic sulla sezione Support per questo prodotto.

Signiﬁ cato dei termini particolari

In tutta la documentazione relativa al prodotto sono utilizzati iseguenti termini per indicare vari livelli di potenziale

pericolo durante il funzionamento:

AVVISO: Procedure che, se non sono seguite correttamente, possono creare danni materiali E nessuna oscarsa

possibilità di lesioni.

ATTENZIONE: Procedure che, se non sono seguite correttamente, possono creare danni materiali E possibili gravi

lesioni.

AVVERTENZA: Procedure che, se non debitamente seguite, espongono alla possibilità di danni alla proprietà ﬁ sica

opossono omportare un’elevata possibilità di provocare ferite superﬁ ciali. Ulteriori precauzioni per la sicurezza e

avvertenze.

AVVERTENZA: Leggere TUTTO il manuale di istruzioni e prendere familiarità con le caratteristiche del prodotto, prima

di farlo funzionare. Un utilizzo scorretto del prodotto può causare danni al prodotto stesso, alle persone oalle cose,

provocando gravi lesioni.

Questo è un prodotto di hobbistica soﬁ sticato e NON un giocattolo. È necessario farlo funzionare con cautela e

responsabilità e avere conoscenze basilari di meccanica. Se questo prodotto non è utilizzato in maniera sicura e

responsabile potrebbero veriﬁ carsi lesioni odanni al prodotto stesso oad altre proprietà. Non è un prodotto adatto

aessere utilizzato dai bambini senza la diretta supervisione di un adulto. Non usare componenti non compatibili

o alterare il prodotto in nessuna maniera al di fuori delle istruzioni fornite da Horizon Hobby, LLC. Questo manuale

contiene le istruzioni per un funzionamento e una manutenzione sicuri. È fondamentale leggere e seguire tutte le

istruzioni e le avvertenze del manuale prima di montare, conﬁ gurare ofar funzionare il Prodotto, al ﬁ ne di utilizzarlo

correttamente e di evitare danni olesioni gravi.

MINIMO 14 ANNI. NON È UN GIOCATTOLO.

 COME USARE IL MANUALE

Questo manuale è diviso in sezioni per rendere più facile la comprensione del montaggio.

 AVVERTIMENTI E PRECAUZIONI PER LA SICUREZZA

Prima dell’uso leggere attentamente tutte le istruzioni e le precauzioni per la sicurezza. In caso contrario si potrebbero

procurare incendi, danni o ferite.

Componenti

Usare solo componenti compatibili. Se ci fossero dubbi riguardo alla compatibilità, è opportuno far riferimento alle

istruzioni relative al prodotto o ai componenti oppure rivolgersi al reparto Horizon Hobby di competenza.

Volo

Per sicurezza volare solo in aree molto ampie. Meglio se in campi volo autorizzati per modellismo. Consultare le

ordinanze locali prima di scegliere luogo dove volare.

Elica

Tenere gli oggetti liberi (vestiti, penne, cacciaviti, ecc.) lontano dall’elica, prima che vi restino impigliati. Bisogna fare

attenzione anche con le mani perché c’è il rischio di ferirsi anche gravemente.

Batterie

Quando si maneggiano o si utilizzano le batterie, bisogna attenersi alle istruzioni del costruttore; il rischio è di procurare

incendi, specialmente con le batterie LiPo, con danni e ferite serie.

Piccole parti

Questo kit comprende delle parti di piccole dimensioni e non lo si può lasciare incustodito se c’è la presenza di bambini

che li possono inghiottire e rimanere soffocati o intossicati.

 RACCOMANDAZIONI PER OPERARE IN SICUREZZA

• Controllare attentamente il modello prima di ogni volo per accertarsi che sia idoneo.

• Essere consapevoli che un altro utente della frequenza in uso, potrebbe procurare delle interferenze.

• Essere sempre cortesi e rispettosi nei confronti degli altri utilizzatori dell’area in cui ci si trova.

• Scegliere un’area libera da ostacoli e abbastanza ampia da permettere lo svolgimento del volo in sicurezza.

• Prima del volo veriﬁ care che l’area sia libera da amici e spettatori.

• Stare attenti alle altre attività che si svolgono in vicinanza della vostra traiettoria di volo, per evitare possibili conﬂ itti.

• Pianiﬁ care attentamente il volo prima di lanciare il modello.

• Rispettare sempre scrupolosamente le regole stabilite dall’associazione locale.

 PRIMA DI INIZIARE IL MONTAGGIO

• Togliere tutti i pezzi dalla scatola.

• Veriﬁ care che la fusoliera, l’ala e i piani di coda non siano danneggiati.

• Se si trovano parti danneggiate, contattare il negozio da cui è stato acquistato.

Se si trovano delle pieghe nella ricopertura, si possono togliere usando una pistola ad aria calda (HAN100) e guanto per

ricopertura (HAN150), oppure un ferro per ricopertura (HAN101) con la sua calza di protezione (HAN141). Usare cautela

quando si lavora in aree del rivestimento dove ci sono dei colori sovrapposti, per evitare la loro separazione.

• Caricare il trasmettitore e la batteria di volo.

• Centrare stick e trim sul trasmettitore.

• Con una radio computerizzata creare una nuova memoria per questo modello.

• Facendo riferimento alle istruzioni del radiocomando, connettere (bind) trasmettitore e ricevitore.

IMPORTANTE: Ripetere la procedura di connessione una volta regolate le corse, per evitare che i servi vadano a ﬁ ne

corsa. Garantirà anche che le impostazioni di inversione del servo vengano salvate nel sistema radio.

Ultra Stick

™

30cc

 BUILDING PRECAUTIONS

During assembly, we recommend resting the parts on a

soft surface such as a soft towel to help prevent denting

the sheeting.

 REMOVING WRINKLES

The covering of your model may develop wrinkles during

shipping and will require the use of a heat gun (HAN100)

and covering glove (HAN150) or covering iron (HAN101)

with a sealing iron sock (HAN141) to remove them. Use

caution while working around areas where the colors

overlap to prevent separating the colors. Avoid using

too much heat, which could separate the colors. Placing

a cool damp cloth on adjacent colors will also help in

preventing the separation of the colors while removing

wrinkles.

 TRANSPORTATION AND STORAGE

When transporting and storing your model, you will

need a minimum of 80 inches (2m) in length, and 18

inches (46cm) in height to accommodate the size of the

fuselage. We also recommend the use of a wing bag

and stabilizer bags to help protect these surfaces during

transport and storage. The control horns and linkages can

also cause damage to nearby surfaces even when placed

in storage bags. Always place surfaces so the tops are

together to prevent damage from the control horns and

linkages.

 OPTIONAL FLOAT INSTALLATION

When installing the recommended ﬂ oats on your Ultra

Stick 30cc, make sure to use the optional ﬂ oat strut

set HAN236519. These struts are longer than those in

the recommended ﬂ oat kit and provide the necessary

propeller clearance for water operation. When installing

the struts, make sure to use the longer struts at the front,

and the shorter struts at the rear. This is necessary to

obtain the correct angle between the wing and ﬂ oats.

 HINWEISE ZUM BAU

Während des Zusammenbaus empfehlen wird, dass die

Teile auf einer weichen Oberﬂ äche, wie einem Handtuch,

abgelegt werden, um ein Eindrücken der Bleche zu

verhindern.

 ENTFERNEN VON FALTEN

Während des Transportes können bei der Bespannung

Falten aufgetreten sein. Sie können diese mit dem

Heißluftfön (HAN100) und Bespannhandschuh (HAN150)

oder dem Bügeleisenbezug (HAN141) entfernen. Bitte

achten Sie bei überlappenden Farben diese nicht durch

zuviel Hitze zu lösen. Ein kühlendes Stück Stoff kann hier

neben den Falten aufgelegt helfen, dass die Farben sich

nicht trennen.

 TRANSPORT UND LAGERUNG

Bei dem Transport des Modells benötigen Sie mindestens

2 Meter Länge und 46cm Höhe für den Rumpf. Wir

empfehlen ebenfalls Flächen- und Leitwerkstaschen um

Transportschäden zu vermeiden. Durch die Ruderhörner

können ebenfalls Flächen beschädigt werden, so dass

diese nur mit den Oberseiten zueinander gelagert werden

sollten.

 OPTIONALE MONTAGE DER SCHWIMMER

Bei der Montage der empfohlenen Schwimmer auf

dem Ultra Stick 30 cc sicherstellen, den optionalen

Schwimmerverstrebungssatz HAN236519 zu verwenden.

Diese Verstrebungen sind länger als die im empfohlenen

Schwimmersatz und bieten den erforderlichen Freiraum

für die Propeller beim Betrieb auf dem Wasser. Bei der

Montage der Verstrebungen sicherstellen, die längeren

Verstrebungen vorne und die kürzen Verstrebungen

hinten anzubringen. Dies ist notwendig, um den korrekten

Winkel zwischen dem Flügel und den Schwimmern zu

erreichen.

 PRÉCAUTIONS D’ASSEMBLAGE

Lors de l’assemblage de votre modèle, nous vous

recommandons de poser les pièces sur une surface

douce comme une serviette douce pour éviter d’abîmer

l’entoilage.

 ÉLIMINATION DES PLIS

L’entoilage de votre modèle peut développer des plis

lors de l’expédition. Vous pouvez les lisser en utilisant le

pistolet à air chaud (HAN100) et le gant (HAN150) ou le

fer à entoiler (HAN101) avec la chaussette de protection

(HAN141). Soyez vigilant sur les zones où plusieurs

couleurs d’entoilage sont superposées, une température

trop élevée pourrait séparer les couleurs. Placez un

chiffon humide et froid sur les couleurs adjacentes pour

éviter leur séparation lorsque vous enlevez les plis.

 TRANSPORT ET STOCKAGE

Lorsque vous transportez ou stockez votre modèle, il

vous faudra un espace d’au moins 2m de longueur et

46cm de hauteur pour accueillir le fuselage. Nous vous

recommandons également l’utilisation d’un sac pour ailes

et de sacs pour stabilisateurs pour les protéger lors du

transport ou stockage. Les guignols et tringleries peuvent

également endommager les gouvernes même dans

les sacs de stockage. Placez toujours les gouvernes de

façon à ce que les parties supérieures soient l’une contre

l’autre pour éviter les contacts et dommages causés par

les guignols ou tringleries.

 INSTALLATION DES FLOTTEURS

OPTIONNELS

Lorsque vous installez les ﬂ otteurs recommandés sur

votre Ultra Stick 30cc, assurez-vous de bien utiliser

les haubans de ﬂ otteurs optionnels HAN236519. Ces

haubans sont plus longs que ceux du kit de ﬂ otteurs et

assurent le bon dégagement d’hélice pour une utilisation

sur l’eau. Lors de l’installation des haubans, assurez-vous

bien d’utiliser les haubans les plus longs à l’avant et les

plus courts à l’arrière. Ceci est nécessaire pour obtenir le

bon angle entre l’aile et les ﬂ otteurs.

 PRECAUZIONI PER LA COSTRUZIONE

Durante l’assemblaggio noi consigliamo di appoggiare

le varie parti su di una superﬁ cie morbida come un

asciugamano di spugna per evitare ammaccature al

rivestimento.

 TOGLIERE LE GRINZE

rivestimento di questo modello potrebbe sviluppare delle

grinze durante la spedizione e quindi per toglierle, sarà

necessario usare una pistola termica (phon) (HAN100) e

un guanto speciale (HAN150), oppure un ferro apposito

per rivestimenti (HAN101) con la sua calza (HAN141).

Bisogna usare cautela quando si lavora attorno ad

aeree con sovrapposizione di colori per evitare la loro

separazione. Evitare di scaldare troppo per non separare

i colori. Mettere un panno umido fresco sui colori vicini,

aiuta a prevenire la separazione dei colori mentre si

tolgono le grinze.

 TRASPORTO E DEPOSITO

Quando si trasporta o si tiene in magazzino questo

modello, sarà necessario uno spazio di 2 metri di

lunghezza e di 46 centimetri in altezza per adattarsi alle

dimensioni della fusoliera. Si consiglia anche di usare

una custodia per proteggere le ali e lo stabilizzatore. Le

squadrette e i rinvii possono pure causare danni alle

superﬁ ci vicine anche se sono sistemate dentro alle

custodie. Per evitare questo, sistemare le superﬁ ci in

modo da mettere a contatto le loro parti superiori che non

hanno squadrette o rinvii.

 INSTALLAZIONE GALLEGGIANTI

OPZIONALI

Quando si installano i galleggianti consigliati sull’Ultra

Stick 30cc, accertarsi di usare il set di supporti opzionali

HAN236519. Questi supporti sono più lunghi di quelli

contenuti nel kit di galleggianti consigliato e garantiscono

la distanza necessaria tra l’elica e l’acqua. Quando si

installano i supporti, accertarsi di usare quelli più lunghi

davanti e quelli più corti dietro. In questo modo si ottiene

l’angolo corretto tra l’ala e i galleggianti.

12EN

 AILERON AND FLAP INSTALLATION

1. Use a 1/16-inch (1.5mm) drill bit to clear the holes of any

debris for the control horn mounting screws.

2. Puncture the covering so the control horn backing plate

can be accessed by the screws.

3. Use a hobby knife to separate the control horn backplate

from the control horn.

4. Insert the three M2 x 25 machine screws into the holes

of the control horn, then into the holes in the aileron.

Make sure the control horn is installed on the bottom of

the aileron.

5. Slide the control horn backplate on the screws. Apply

a small amount of canopy glue on the screws using a

toothpick, then thread the M2 nuts on the screws. Use

a #1 Phillips screwdriver and 4mm nut driver to tighten

the screws.

10.

6. Use side cutters to trim the screws.

7. Use a ﬁ le to lightly ﬁ le any sharp points from the screws

after they have been trimmed. Use care not to contact

the control surface with the ﬁ le. Prepare and install

the ﬂ ap control horns at this time following the same

procedure as the aileron control horns.

8. Use a pin vise and 1/16-inch (1.5mm) drill bit to drill

a hole in the center of each hinge slot to allow the CA

to wick into the hinge. Drill holes in both the wing and

control surfaces at this time. The ailerons and ﬂ aps can

both be prepared during this step.

9. Remove the ailerons from the wing panel. Place a T-pin

in the center of each hinge.

10. Slide the hinges into position with the T-pin resting

against the edge of the control surface.

13 EN

Ultra Stick

™

30cc

11.

12.

13.

14.

15.

16.

11. Repeat the previous steps to install all four of the aileron

hinges.

16. Check the gap between the ﬂ ap and aileron. Use a thin

ruler (or similar) as a spacer so the gap between the

left and right ailerons and ﬂ aps are the same. Glue the

hinges for the ﬂ aps using thin CA. Once the CA cures,

gently pull on the ﬁ xed surface and control surface to

make sure the hinges are glued securely. If not, apply

additional CA to secure each of the hinges.

12. Fit the aileron to the wing by inserting the hinges into the

slots in the wing.

 AILERON AND FLAP SERVO INSTALLATION

1. Remove the aileron servo hatch from the wing. Make

sure to keep the string taped to the wing so it doesn’t fall

into the wing.

13. Check that there is a slight gap between the wing and

the end of the aileron. Use a thin ruler (or similar) as a

spacer so both the left and right ailerons have the same

size gap.

2. Check that the servo mount is glued securely to the

servo cover. If the mount is not secure, use a small

amount of medium CA or epoxy to make sure the mount

is securely fastened to the servo cover.

14. Apply thin CA to the top and bottom of each hinge. Once

the CA cures, gently pull on the ﬁ xed surface and control

surface to make sure the hinges are glued securely. If

not, apply additional CA to secure each of the hinges.

3. Remove the aileron and ﬂ ap cover from the wing. Use a

toothpick to puncture the covering to locate the holes for

the aileron and ﬂ ap cover screws.

15. Prepare the three hinges for the ﬂ ap and place it into

position on the wing.

4. Place the aileron and ﬂ ap cover into position. Use a drill

and 5/32-inch (2mm) drill bit to drill the holes in the

servo cover mounts.

14EN

10.

11.

12.

13.

14.

5. Thread an M3 x 15 self-tapping screw into each of the

holes in the aileron and ﬂ ap servo cover mounting holes.

Remove the screws before proceeding.

10. Secure the servo to the cover using a 2mm hex wrench

and the screws provided with the servo.

7. Install the grommets and brass eyelets in the servos.

Follow any instructions included with the servo. Prepare

both ﬂ ap and aileron servos at this time.

12. Secure an 18-inch (460mm) servo extension to the

tip servo using a commercially available fastener

(SPMA3054).

6. Apply a small amount of thin CA to harden the threads

made in the previous step. Allow the CA to fully cure

before installing the aileron servo cover.

11. Center the servo, then secure the servo arm so it is

perpendicular to the servo centerline.

8. Fit the servo between the servo mounting tabs in the

aileron servo tray. The servo arm will be centered in the

slot. Mark the locations for the servo mounting screws

using a pencil, then remove the servo.

9. Use a drill and a 1/16-inch (1.5mm) drill bit to drill the

holes for the servo mounting screws in the locations

marked in the previous step. Use a 2mm hex wrench to

thread a servo mounting screw into each of the holes in

the aileron servo mounting holes. Remove the screws,

then apply a small amount of thin CA to harden the

threads.

13. Tie or tape the string located inside the wing to the end

of the servo lead.

14. Retrieve the servo lead at the wing root. Guide the lead

through the hole in the bottom of the wing.

15 EN

Ultra Stick

™

30cc

20.

21.

15.

16.

17.

18.

19.

15. Secure the aileron cover in the wing using four M3 x 15

self-tapping screws.

16. Thread an M3 nut on one end of the 100mm pushrod.

Slide a clevis retainer (silicone tubing) on a metal clevis,

then thread the clevis on the rod. Thread a nylon ball end

12-turns on the opposite end of the threaded rod, then

snap the aluminum ball into the ball end using pliers.

17. Attach the ball end to the outer hole of the servo arm

using the hardware included with the servo arm. Make

sure to install the M3 washer (included with the kit)

between the head of the screw and ball end. Tighten the

hardware using a 1/4-inch nut driver and 3/32-inch hex

wrench.

18. Connect the clevis to the outer hole of the control horn.

With the radio on and aileron servo centered, adjust

the link to center the aileron. Once set, slide the clevis

retainer (silicone tubing) over the forks of the clevis, then

tighten the nut against the clevis. Use thread lock on the

nut to prevent it from vibrating loose.

19. Install the ﬂ ap servo and assemble the linkage for the

ﬂ ap using the same technique as the aileron linkage.

The pushrod for the ﬂ ap linkage also measures 100mm

in length. With the ﬂ ap servo centered, adjust the link

so the ﬂ ap is in the mid-ﬂ ap position of 1

-inches

(40mm).

20. Use the radio system to set the ﬂ ap to the up position.

Use the radio to center the ﬂ ap into the neutral position.

21. Use the radio system to set the ﬂ ap to the down position.

Use the radio to set the full deﬂ ection position.

 WING INSTALLATION

1. Slide the wing tube into the wing tube socket.

2. Slide the wing panels together. There will be no gap

between the panels.

3. Fit the dowels on the leading edge of the wing into the

holes in the fuselage.

16EN

4. Place the wing bolt plate on the wing, then thread the

1/4-20 x 13/4-inch nylon wing bolts into the blind nuts in

the fuselage to secure the wing.

 STABILIZER INSTALLATION

Î Check the stabilizer mounting surface on the

fuselage to make sure it is flush with the fuselage

sides. If the fuselage sides protrude beyond the

stabilizer mounting surface, then sand them flush.

1. Remove the elevators from the stabilizer. Fit the stabilizer

into the notch in the fuselage. Center the stabilizer.

2. Measure from the tip of the stabilizer to the wing.

Position the stabilizer so both measurements are equal.

3. Check the alignment of the stabilizer to the wing. It

should be equal on both sides of the fuselage.

4. Check all alignments. Mark the outline of the fuselage on

the top of the stabilizer.

5. Use a ruler and carefully cut the covering 1/8 inch (3

mm) inside the line drawn on the stabilizer to remove

the covering from the center of the stabilizer. Remove

the top and bottom covering. Use care not to cut into the

underlying wood, weakening the stabilizer.

6. Use a paper towel and isopropyl alcohol to remove the

lines from the stabilizer.

7. Mix 1/2 ounce (15ml) of 30-minute epoxy. Use an epoxy

brush to apply epoxy to the exposed wood on the top of

the stabilizer.

8. Use an epoxy brush to apply epoxy to the stabilizer

mounting surface in the notch in the fuselage for the

stabilizer.

9. Fit the stabilizer back into position. Check the alignment

following steps 1 through 3, then use a paper towel and

isopropyl alcohol to remove any excess epoxy from the

fuselage and stabilizer.

17 EN

Ultra Stick

™

30cc

10.

10. Use clamps to hold the stabilizer in position. Allow the

epoxy to fully cure before proceeding.

 FIN INSTALLATION

1. Fit the ﬁ n into the slot in the fuselage. Use a ruler to

check the alignment of the ﬁ n to the rear edge of the

fuselage.

2. Use a felt-tipped pen to trace the outline of the ﬁ n on the

top of the fuselage. Also mark the bottom of the ﬁ n along

the fuselage.

3. Use a hobby knife with a #11 blade to carefully remove

the covering 1/8-inch (3mm) inside the lines drawn from

the top of the fuselage at the rear of the ﬁ n.

4. Use a hobby knife with a #11 blade to carefully remove

the covering 1/8-inch (3mm) inside the lines drawn from

the top of the fuselage at the front of the ﬁ n.

5. Use a ruler and carefully cut the covering 1/8 inch (3

mm) below the line drawn on the ﬁ n. Remove the bottom

covering. Use care not to cut into the underlying wood,

weakening the ﬁ n.

6. Mix 1/2 ounce (15ml) of 30-minute epoxy. Use an epoxy

brush to apply the epoxy in the slot for the ﬁ n and to the

exposed wood on the top of the fuselage.

7. Apply epoxy to the exposed wood on the bottom of the

ﬁ n where it comes in contact with the fuselage.

8. Fit the ﬁ n in position. Check that it is square to the

fuselage. Use tape if necessary to hold the ﬁ n in position

until the epoxy fully cures.

 ELEVATOR INSTALLATION

1. Attach the control horns to the top of the elevators

following the same procedure as the aileron and ﬂ ap

control horns.

18EN

2. Drill a 1/16-inch (1.5mm) hole in the center of each

hinge slot for in both the elevator and stabilizer. Prepare

and install the elevator hinges, then ﬁ t the elevator to the

stabilizer. Check that the ends of the elevator aligns with

the ends of the stabilizer.

3. Check to make sure the control horn is on the top of the

elevator, and that the trim scheme from the elevator and

stabilizer are on the same side.

4. Repeat the previous steps to install the remaining

elevator. Glue the hinges at this time following the same

procedure as the aileron and ﬂ ap hinges. Once the CA

cures, gently pull on the ﬁ xed surface and control surface

to make sure the hinges are glued securely. If not, apply

additional CA to secure each of the hinges.

 RUDDER AND TAIL WHEEL INSTALLATION

1. Use a 1.5mm hex wrench to loosen the setscrews in the

wheel collar for the tail wheel. Slide the wheel collar as

close to the tail wheel as possible.

2. Lightly sand the tail wheel wire where it contacts the

rudder. Use a paper towel and isopropyl alcohol to

remove any oil or debris from the wire.

3. Mix a small amount of 15-minute epoxy. Use a toothpick

to apply epoxy to the rudder where the tail wheel wire

will come in contact with the exposed wood.

4. Use a toothpick to apply epoxy to the tail wheel wire

where it contacts the rudder.

5. Fit the wire into the rudder. Use a paper towel and

isopropyl alcohol to remove any excess epoxy from the

rudder and wire.

6. Use low-tack tape to hold the tail wheel wire in position

until the epoxy fully cures. Once cured, remove the tape

from the rudder.

7. Install the control horn on the rudder. Note the control

horn will be on the left side of the rudder.

19 EN

Ultra Stick

™

30cc

10.

11.

12.

8. Prepare the hinge slots and hinges for the rudder. Install

the hinges and ﬁ t the rudder to the ﬁ n. Align the top of

the ﬁ n and rudder. Use thin CA to glue the hinges. Once

the CA cures, gently pull on the ﬁ xed surface and control

surface to make sure the hinges are glued securely. If

not, apply additional CA to secure each of the hinges.

9. Position the tail wheel bracket so it is centered on the

bottom of the stabilizer. Use a felt-tipped pen to mark the

location for the mounting screws. Use a drill and 5/32-

inch (2mm) drill bit to drill the holes for the screws.

10. Use a #1 Phillips screwdriver to thread the M3 x 20 self-

tapping screws into the holes. Remove the screws, then

apply thin CA into the holes to harden the threads. Once

the CA has fully cured, install the three screws to secure

the tail wheel bracket to the stabilizer.

11. Slide the wheel collar against the tail wheel bracket and

tighten the setscrew using a 1.5mm hex wrench.

12. Attach the tail wheel to the wire using a 3mm wheel

collar and 3mm setscrew. Apply thread lock to the

setscrew, then tighten the setscrew using a 1.5mm hex

wrench.

Î Use the foam tail wheel for quieter operation

when using EP power systems from asphalt runways,

or the rubber tail wheel for grass runways.

 RADIO INSTALLATION

1. Prepare the rudder and elevator servos by installing the

rubber grommets and brass eyelets. Install the elevator

(1) and the rudder (2) servos in the fuselage with the

output of the servos facing the front of the fuselage.

Î Servo location may vary in the

production version of your aircraft.

2. Secure the receiver in the fuselage using two-sided

tape and a hook and loop strap. Connect the rudder and

elevator servos to the receiver.

Î When using the recommended receiver,

make sure it is secure and installed according to

the instructions provided with the receiver.

3. Use a hobby knife with a #11 blade to remove the

covering from the side of the fuselage for the receiver

switch. Mount the switch and connect it to the receiver.

4. Use hook and loop tape to secure one remote receiver as

far forward in the fuselage as possible.

5. The second remote receiver is mounted as far back as

possible using hook and loop tape.

20EN

10.

11.

12.

13.

14.

6. Mount the receiver battery in the fuselage using hook

and loop tape. Make a brace from mixing sticks to keep

the battery secure in the fuselage.

Î The ignition battery can be mounted in the

same location when a gas engine is being used.

Connect a 6-inch (150mm) extension to the battery

to connect it to the ignition switch when installed.

Î Reposition the batteries as necessary to

achieve the correct Center of Gravity depending

on your engine or motor selection.

7. Slide the 36-inch (914mm) threaded pushrod into the

pushrod tube in the fuselage. Guide the pushrod out the

exit at the rear of the fuselage.

8. Thread an M3 nut on the pushrod. Slide a clevis retainer

(silicone tubing) on a metal clevis, then thread the clevis

on the pushrod. Prepare the rudder servo horn and install

it on the rudder servo. Connect the clevis to the servo

arm.

9. Thread an M3 nut on the pushrod. Slide a clevis retainer

(silicone tubing) on a metal clevis, then thread the clevis

on the pushrod. Connect the clevis to the center hole of

the rudder control horn. With the radio system on and

rudder servo centered, adjust the clevises to center the

rudder. Once centered, slide the retainers over the forks

of the clevises, then tighten the nuts against the clevises.

Use thread lock on the nuts to prevent them from

vibrating loose.

10. Thread a nylon ball end on the 35

-inch (900mm)

elevator pushrod, then snap the ball into the ball end.

Slide a 3mm washer on an M3 x 12 socket head cap

screw, then thread the screw into the outer hole of the

elevator servo arm.

11. Slide a 3mm washer on the screw, then a 3mm lock

nut. Use a 2.5mm hex wrench and 5.5mm nut driver to

tighten the hardware. Prepare both elevator pushrod at

this time.

12. Slide the pushrod into the tubes, guiding out of the

fuselage near the elevators. Center the elevator servos

and attach the servo arms to the servos.

13. Use an M3 nut, metal clevis and clevis retainer (silicone

tubing) to prepare the ends to attach the pushrods to the

elevator control horns. Center the servos and adjust the

clevises to center the elevators. Slide the retainer over

the forks of the clevis and tighten the nut the against the

clevis after applying thread lock to the nut.

Î When using heavier engines, it may be necessary

to mount the elevator servos at the rear of the fuselage.

Follow the steps covering this optional installation.

14. Connect an 18-inch (460mm) extension to the elevator

servo. Remove the covering using a hobby knife and #11

blade. Mount the elevator servo in the fuselage with the

output facing toward the front of the fuselage.

La page charge ...

Hangar 9 HAN2365 Le manuel du propriétaire

Marque: Hangar 9

Modèle: HAN2365

Catégorie: Jouets télécommandés

Taper: Le manuel du propriétaire

Ce manuel convient également à

HANGAR 9 Ultra Stick 30cc

Télécharger le PDF

rapport

dans d''autres langues

italiano: Hangar 9 HAN2365 Manuale del proprietario
English: Hangar 9 HAN2365 Owner's manual
Deutsch: Hangar 9 HAN2365 Bedienungsanleitung

Hangar 9 HAN2365 Le manuel du propriétaire

Ce manuel convient également à

Hangar 9 HAN2365 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents