Hangar 9 HAN2365 Le manuel du propriétaire

Catégorie
Jouets télécommandés
Taper
Le manuel du propriétaire

Ce manuel convient également à

Ultra Stick
30cc
Instruction Manual
Bedienungsanleitung
Manuel d’utilisation
Manuale di Istruzioni
2
SPECIFICATIONS • SPEZIFIKATIONEN • SPÉCIFICATIONS • SPECIFICHE LARGE PARTS LAYOUT • BAUTEILE (OHNE KLEINTEILE) • GRANDES PIÈCES • SCHEMA DEI COMPONENTI GRANDI
81.0 in (206 cm)
1360 sq in (87.8 dm2) Total/Totale
73 in (185 cm)
12–14 lbs (5.4–6.35 kg)
2-Stroke Gas: 30cc, 4-Stroke gas/petrol: 36cc
2-Takt Benziner: 30cc, 4-Takt Benzin: 36cc
2 temps Essence: 30cc, 4 temps essence: 36cc
2-Tempi Gas: 30cc, 4 tempi benzina: 36 cc
Electric Power Power: Power 160 Brushless
Elektro Antrieb Power: Power 160 Brushless
Moteur électrique (EP): Power 160 Brushless
Motore elettrico: Power 160 Brushless
5-channel (or greater) with 8 servos
5-Kanal (oder größer) mit 8-Servos
5 voies (ou plus) avec 8 servos
a 5 canali (o più) con 8 servo
Spinner (not included): 3-inch
Spinner (nicht im Lieferumfang enthalten): 75mm
Cône (non inclus): 75mm
Ogiva dell’elica (non inclusa): 75mm
4
1
6
12
16
15
2
9
8
11
7
3
10
13
14
17
5
3
Ultra Stick
30cc
Part # English Deutsch Français Italiano
REPLACEMENT PARTS • ERSATZTEILE • PIÈCES DE RECHANGE • PEZZI DI RICAMBIO
1 HAN236501 Fuselage Rumpf Fuselage Fusoliera
2 HAN236502 Left Wing with Aileron and Flap Tragfl äche Links mit Querruder und Klappe Aile gauche avec aileron et volet Semiala sinistra con alettone e fl ap
3 HAN236503 Right Wing with Aileron and Flap Tragfl äche Rechts mit Querruder und Klappe Aile droite avec aileron et volet Semiala destra con alettone e fl ap
4 HAN236504 Vertical Stabilizer with Rudder Vertikaler Stabilisator mit Seitenruder Stabilisateur vertical avec dérive Stabilizzatore verticale con direzionale
5 HAN236505 Horizontal Stabilizer with Elevators Horizontaler Stabilisator mit Höhenruder Stabilisateur horizontal avec profondeur Stabilizzatore orizzontale con elevatori
6 HAN236506 Wing Tube (1.25 inch) Tragfl ächenverbinder (1.25 inch) Clé d’aile (1.25 inch) Tubo dell’ala (1.25 inch)
7 HAN236507 Landing Gear Set Fahrwerk Set Train d’atterrissage Set del carrello di atterraggio
8 HAN236508 Wheel Pants Radverkleidung Carénage de roue Copriruote
9 HAN236509 Aileron and Flap (LH) Querruder und Klappe (LH) Aileron et volet (côté gauche) Alettone e fl ap sinistro
10 HAN236510 Aileron and Flap (RH) Querruder und Klappe (RH) Aileron et volet (côté droit) Alettone e fl ap destro
11 HAN236511 Hardware Set Kleinteile Set Sachet de visserie Set dei pezzi
12 HAN236513 Fuselage Hatch Rumpfklappe Capot du fuselage Portello della fusoliera
13 HAN236514 Wheel Set: Reifensatz Roues Set ruote
14 HAN236515 EP Battery Tray EP-Akkuhalterung Platine moteur électrique Portabatteria per motore elettrico
15 HAN236516 Pushrod Set Gestänge / Anlenkungen Set Jeu de tringleries Set dell’asta di spinta
16 HAN236517 Tail Wheel Assembly Spornrad m. Zbh. Assemblage de roulette de queue Gruppo del ruotino di coda
17 HAN236518 Fuel Tank 15oz (450cc) Kraftstoffmotor 450cc (15oz) Réservoir carburant 450cc (15oz) Serbatoio carburante 450 cc
SMALL PARTS (NOT SHOWN)•KLEINTEILE (NICHT ABGEBILDET)•PETITES PIÈCES (NON REPRÉSENTÉES)•PARTI DI PICCOLE DIMENSIONI (NON MOSTRATE)
HAN236512 Decal Set Dekorbogen Planche de décoration Set di decalcomanie
OPTIONAL ITEMS • OPTIONALE TEILE • ÉLÉMENTS OPTIONNELS • ARTICOLI OPZIONALI
EVOA118 Engine Soft-Mount Kit 20-40cc (10-32) Weicher Motor-Halterungssatz 20-40cc (10-32) Support moteur sur silent block 20-40cc (10-32) Kit supporto motore morbido 20-40 cc (10-32)
SPMAR6210
AR6210 6-Channel DSMX
®
Receiver
AR6210 6 Kanal DSMX®-Empfänger Récepteur Spektrum AR6210 6 voies DSMX Ricevente AR6210 DSMX® 6 canali
SPMAR636 AR636 6-Channel AS3X Sport Receiver AR636 6 Kanal AS3X-Sportempfänger Récepteur Spektrum AR636 6 voies AS3X Ricevente sport AR636 AS3X 6 canali
SPMAR7350
AR7350 7 Channel AS3X RX with integrated
telemetry
AR7350 7 Kanal AS3X RX mit integrierter Telemetrie
Récepteur Spektrum AR7350 7 voies AS3X avec
télémétrie intégrée
Ricevente AR7350 AS3X 7 canali con telemetria
integrata
SPMAR7610 AR7610 7-Channel DSMX Hi Speed Receiver AR7610 7-Kanal DSMX HiSpeed Empfänger
Récepteur Spektrum AR7610 7 voies DSMX haute
vitesse
Ricevente Hi Speed AR7610 DSMX 7 canali
SPMAR8000 AR8000 8-Channel DSMX Receiver AR8000 8 Kanal DSMX-Empfänger Récepteur Spektrum AR8000 8 voies DSMX Ricevente AR8000 DSMX 8 canali
SPMAR9110 AR9110 9-Channel DSMX PowerSafe Receiver AR9110 9 Kanal DSMX PowerSafe-Empfänger Récepteur Spektrum AR9110 9 voies DSMX PowerSafe Ricevente PowerSafe AR9110 DSMX 9 canali
WGT201
Extreme Little Tote Double 42”x22”x14” Red/
Black
Extreme Little Tote Double 42” x 22” x 14” Red/Black
Sac de transport pour ailes Extreme Little Tote Double
106 x 55 x 35cm Rouge/Noir
Extreme Little Tote Double 42” x 22” x 14” rosso/
nero
HAN9151 x3
Aluminum Servo Arm, 1-inch: SPM, JR
(For Rudder and Elevator 3D control throw)
Aluminium-Servoarm, 250mm (1 Zoll): SPM,JR
(Für Seitenruder und Höhenruder 3D-Ruderausschlag)
Palonnier servo aluminium 25,4mm: SPM, JR
(Pour débattements dérive et profondeur 3D)
Squadretta servo alluminio, 1'': SPM, JR
(per escursione 3D dei comandi direzionale ed
elevatore)
SPMSA6265 x7
A6265 HV Digital Hi-Torque MG Aircraft Servo
(For Extreme 3D fl ying)
A6265 HV Digitaler Hi-Torque MG Flugzeugservo (für
extremen 3D-Flug)
Servo digital A6265 HV couplé élevé, pignons métal
pour avion (Pour vol 3D extrême)
Servo digitale MG alto voltaggio alta coppia
A6265 (per volo 3D estremo)
4
Part # English Deutsch Français Italiano
REQUIRED RADIO EQUIPMENT • ERFORDERLICHE RC AUSRÜSTUNG • ÉQUIPEMENT RADIO REQUIS • APPARECCHIATURE RADIO NECESSARIE
SPMAR9350
AR9350 9-Channel AS3X
®
Receiver
Spektrum AR9350 9-Kanal AS3X-Empfänger Récepteur AR9350 9 voies AS3X Ricevente AR9350 9-canali AS3X
SPMB2200LFRX 6.6V 2200mAh 2S LiFe Receiver Battery 2200mA 2S 6,6V LiFe Empfänger-Akku Batterie récepteur Li-Fe 2S 6,6V 2200mA Batteria LiFe per ricevente 2S 6,6 V 2200 mAh
EVOA112
Evolution
®
3 Wire Ignition/Rx Switch
Evolution Zündschalter Interrupteur Evolution 3 fi ls Allumage/RX
Evolution, interruttore a 3 fi li accensione/
ricevitore
SPMSA6180 x8 A6180 Digital Aircraft Servo A6180 Digitaler Flugzeugservo Servo digital AR6180 pour avion Servo digitale A6180
HAN9154 x4
Aluminum Servo Arm, 1.5-inch: SPM, JR
(Ailerons and Flaps, Standard Throw)
Aluminium-Servoarm, 38mm: SPM,JR
(Querruder und Landeklappen, Standard-Ausschlag)
Palonnier servo aluminium 38mm: SPM, JR
(Ailerons et Volets, Débattements Standards)
Squadretta servo alluminio, 38 mm: SPM, JR
(Alettoni e fl ap, escursione standard)
OR
HAN9160 x4
Aluminum Servo Arm, 2-inch (JR/SPM)
(Ailerons and Flaps, Extreme Throw)
Hangar 9 Aluminium Servo Arm, 50 mm (JR/SPM)
(Querruder und Landeklappen, Extremer Ausschlag)
Palonnier de servo en aluminium, long 50mm (JR,SPM)
(Ailerons et Volets, Débattements Extrêmes)
Squadretta servo in alluminio 50 mm (JR/SPM)
(Alettoni e fl ap, escursione estrema)
DUB671 x2
Super Strength Long Servo Arm (JR)
(Elevator and Rudder)
Superstärke Servoarm, lang (JR)
(Höhenruder und Seitenruder)
Palonnier de servo super résistant, long (JR)
(Profondeur et dérive)
Squadretta servo super resistente, lungo (JR)
(elevatore e direzionale)
SPMA3001 x4 Heavy-Duty Servo Extension 6-inch Schwerlast-Servoverlängerung 150 mm (6 Zoll) Rallonge de servo, 150 mm Prolunga servo 150 mm
SPMA3003 x2
Heavy Duty Servo Extension 12-inch
(Ailerons)
Schwerlast-Servoverlängerung 300 mm (12 Zoll)
(Querruder)
Rallonge de servo, 300 mm
(Ailerons)
Prolunga servo 300 mm
(Alettoni)
SPMA3004 x2
(Optional)
Heavy Duty Servo Extension 18-inch
(Optional Elevator servo installation)
Schwerlast-Servoverlängerung 460mm (18 Zoll)
(Montage des Höhenruderservo optional)
Rallonge de servo, 460 mm
(Installation du servo de profondeur optionnel)
Prolunga servo 460 mm
(Installazione servo elevatore opzionale)
SPMA3054 Servo Connector Clips (25) Servosteckerklemmen (25) Clips pour connecteur de servo (25) Clips connettori servi (25)
2-STROKE GAS • 2-TAKT BENZINER • 2 TEMPS ESSENCE • 2-TEMPI A BENZINA
EVOE33GX 33GX 33cc (2.00 cu. in.) Gas Engine 33GX 33cc (2,00 Kubikzoll) Kraftstoffmotor Moteur essence Evolution 33GX 33cc (2.00) Motore a benzina 33GX 33 cc
APC17080 17 x 8 Propeller 17 x 8 Propeller Hélice 17 x 8 17 x 8 Elica
HAN116 Fuel Filler with “T” and Overfl ow Fittings Tanknippel mit T-Stück u. Überlauf Fitting Point de remplissage de carburant avec coupleur en T Riempitore carburante con “T” e raccordi troppo
EVOM3 Pitts-style Muffl er, Single Pipe: 33GX Pitts-artiger Schalldämpfer, Einzelrohr: 33GX 33GX - Silencieux Pitts simple sortie Scarico stile Pitts, tubo singolo: 33GX
EVOM4 Pitts-style Muffl er, Dual Pipe: 33GX Pitts-artiger Schalldämpfer, Doppelrohr: 33GX 33GX - Silencieux Pitts double sortie Scarico stile Pitts, doppio tubo: 33GX
SPMB2200LFRX 6.6V 2200mAh 2S LiFe Receiver Battery 2200mA 2S 6,6V LiFe Empfänger-Akku Batterie récepteur Li-Fe 2S 6,6V 2200mA Batteria LiFe per ricevente 2S 6,6 V 2200 mAh
SPMA3001 Heavy Duty Servo Extension 6-inch Schwerlast-Servoverlängerung 150mm (6 Zoll) Rallonge de servo, 150 mm Prolunga servo 150 mm
EVOA112 Evolution 3 Wire Ignition/Rx Switch Evolution Zündschalter Interrupteur Evolution 3 fi ls Allumage/RX
Evolution, interruttore a 3 fi li accensione/
ricevitore
EVOA100 Optical Ignition Kill Switch (Optional) Optischer Zünd-Notausschalter (optional)
Interrupteur optique coupe circuit d'allumage
(optionnel)
Kill switch ottico per avviamento (opzionale)
HAN502016
3-inch 2-Blade Aluminum Spinner:
Cirrus SR22T 30cc
76mm (3 Zoll) Aluminium-Spinner mit 2 Blättern:
Cirrus SR22T 30cc
Cirrus SR20 - Cône en aluminium 3" bipale Ogiva bipala alluminio 3'': Cirrus SR22T 30 cc
5
Ultra Stick
30cc
Part # English Deutsch Français Italiano
ELECTRIC POWER • ELEKTROANTRIEB • MOTEUR ELECTRIQUE (EP) • MOTORE ELETTRICO
EFLM4160A Power 160 Brushless Outrunner Motor, 245Kv Bürstenloser Außenläufer-Motor Leistung 160, 245Kv
Moteur à cage tournante sans balais Power 160 de
245Kv
Motore brushless a cassa rotante Power 160,
245Kv
CSE010010400 Phoenix Edge 120HV, 50V 120-Amp ESC
Phoenix Edge 120HV, 50V 120 A
Geschwindigkeitsregler
Contrôleur Phoenix Edge 120HV, 50V 120A ESC Phoenix Edge 120HV, 50 V 120 A
CSE010000401 Castle BEC PRO V2, 010-0004-01 (Optional) Castle BEC PRO V2, 010-0004-01 (optional) Castle BEC PRO V2, 010-0004-01 (optionnel) BEC Castle PRO V2, 010-0004-01 (opzionale)
EFLB50005S30
5000mAh 5S 18.5V 30C LiPo Battery,12AWG
EC3
5000 mA 5S 18,5V 30C LiPo-Akku,12AWG EC3
Batterie Li-Po 5S 18,5V 5000mA 30C, 12AWG prise
EC3
Batteria LiPo 30C 18,5 V 5S 5000 mAh,12AWG
EC3
KXSB0026
5000mAh 5S 18.5V 30C LiPo Battery, 10AWG:
EC5
5000 mA 5S 18,5V 30C LiPo-Akku,10AWG EC5
Batterie Li-Po 5S 18,5V 5000mA 30C, 10AWG prise
EC5
Batteria LiPo 30C 18,5 V 5S 5000 mAh,10AWG
EC5
APC18010E Thin Electric Propeller, 18 x 10 Elektro Propeller, 18 x 10 Hélice électrique, 18 x 10 Elica elettrica sottile, 18 x 10
HAN502016
3-inch 2-Blade Aluminum Spinner:
Cirrus SR22T 30cc
76mm (3 Zoll) Aluminium-Spinner mit 2 Blättern:
Cirrus SR22T 30cc
Cirrus SR20 - Cône en aluminium 3" bipale Ogiva bipala alluminio 3'': Cirrus SR22T 30 cc
OPTIONAL FLOATS•OPTIONALE SCHWIMMER•FLOTTEURS OPTIONNELS•GALLEGGIANTI OPZIONALI
HAN6030 1/5-Scale Float Set Schwimmersatz im Maßstab 1/5 Set de fl otteurs 1/5 Set galleggianti scala 1:5
HAN236519 Float Strut Set: Ultra Stick 30cc Schwimmerverstrebungssatz: Ultra Stick 30cc Ultra Stick 30cc – Haubans de fl otteurs Set supporti galleggianti: Ultra Stick 30cc
SPMSA4030 x2
A4030 Micro HV Digital Hi-Torque MG Aircraft
Servo
A4030 Micro HV Digitaler Hi-Torque MG Flugzeugservo
Micro servo digital AR4030 HV couple élevé à pignons
métal pour avion
Servo micro digitale A4030 alto voltaggio alta
coppia
SPMA3058 Standard Y-Harness, 6-inch Standard Y-Kabelbaum, 152mm (6 Zoll) Rallonge Y standard, 15cm Cavo a Y standard, 6''
SPMA3004 x2 Heavy Duty Servo Extension 18-inch Schwerlast-Servoverlängerung 460mm (18 Zoll) Rallonge de servo, 460 mm Prolunga servo 460 mm
6
Part # English Deutsch Français Italiano
REQUIRED ADHESIVES • ERFORDERLICHE KLEBSTOFFE • TYPES DE COLLES • ADESIVI NECESSARI
DLMAD44 Roket Rapid CA 5-10 sec: 20g Roket Rapid CA 5-10 s: 20g Colle cyano Roket Rapid 5-10 sec: 20g Colla cianoacrilica Roket Rapid 5-10 sec: 20 g
DLMAD45 Roket Max CA 10-20 sec: 20g Roket Max CA 10-20 s: 20g Colle cyano Roket Max 10-20 sec: 20g Colla cianoacrilica Roket Max 10-20 sec: 20 g
PAAPT715 CA Accelerator Sekundenkleber (CA) Aktivator Accélérateur de colle CA Accelerante colla CA
PAAPT35 15-Minute Epoxy 15 Minuten Epoxy Époxy 15 minutes Colla epoxy 15 minuti
PAAPT42 Threadlock Schraubensicherungslack Frein-fi let Frenafi letti
DLMAD12 R/C Modeller Canopy Glue: 4 oz R/C Modeller Kanzelkleber: 113,4g (4 oz) Colle à verrière R/C Modeller: 113g Colla per capottine R/C Modeller: 4 oz
REQUIRED TOOLS • BENÖTIGTES WERKZEUG • OUTILS REQUIS • ATTREZZI NECESSARI
Box wrench: 1/2-inch Ringschlüssel: 1/2-inch Clé hexagonale: 1/2-inch Chiave esagonale: 1/2-inch
Drill Bohrer Mini-perceuse Trapano
Drill bit: 1/16-inch, 5/64-inch, 1/8-inch
5/32-inch, 3/16-inch
Bohrer: 1,5mm, 2mm, 3mm, 4mm, 4,5mm Forêt : 1,5mm, 2mm, 3mm, 4mm, 4,5mm
Punte per trapano: 1,5mm, 2mm, 3mm, 4mm,
4,5mm
Felt-tipped pen Faserstift Feutre fi n effaçable Pennarello
Epoxy brush Pinsel Pinceau Epoxy Spazzole epoxy
Flat fi le Flachfeile Lime plate Lima piatta
Hemostats Klemme Pince Hemostat Pinzetta
Hex wrench: 3/32-inch, 1.5mm, 2mm, 2.5mm,
3mm, 4mm
Inbusschlüssel: 3/32-inch, 1,5mm, 2mm, 2,5mm,
3mm, 4mm
Tournevis hexagonal: 3/32-inch, 1,5mm, 2mm, 2,5mm,
3mm, 4mm
Chiave esag.: 3/32-inch, 1,5mm, 2mm, 2,5mm,
3mm, 4mm
Hobby knife with #11 blade Hobbymesser mit # 11 Klinge Couteau : Lame numéro 11 Taglierino: #11 lama
Isoplrpyl alcohol Isopropyl Alkohol Alcool isopropylique Alcol isopropilico
Low-tack tape Kreppband Adhésif de masquage Nastro a bassa aderenza
Needle nose pliers Spitzzange Pince fi ne Pinze a becco stretto
Nut driver: 1/4-inch, 4mm, 5.5mm Steckschlüssel. 1/4-inch, 11/32-inch Clés à douilles : 1/4-inch, 11/32 pouce Chiave per dadi: 1/4-inch, 11/32-inch
Paper towels Papiertücher Papier absorbant Asciugamani di carta
Pencil Stift Crayon à papier Matita
Phillips screwdriver: #1 Phillips Schraubendreher: #1 Tournevis cruciforme: #1 Cacciavite a croce: #1
Pin vise Handbohrer Porte forets Trapano manuale
Pliers Zange Pince Pinze
Ruler Lineal Réglet Righello
Sandpaper Schleifpapier Papier de verre Carta vetrata
Scissors Schere Ciseaux Forbici
Side cutters Seitenschneider Pince coupante Lama laterale
Square Geodreieck Équerre Squadra
Tap and drill set, English Gewindeschneider und Bohrerset Taraud et foret Set punte e maschi, Inglese
Tap Handle Halter für Gewindeschneider Épingles Impugnatura per maschiare
T-pins T- Nadeln Epingles Spilli a T
Toothpicks Zahnstocher Cure dents Stuzzicadenti
7
Ultra Stick
30cc
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon
Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.
The following terms are used throughout the product literature to indicate various levels of potential harm when
operating this product:
Meaning of Special Language
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or
no possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a
possibility of serious injury.
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage,
and serious injury OR create a high probability of superfi cial injury.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating.
Failure to operate the product correctly can result in damage to the product, personal property and cause serious
injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic
mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage
to the product or other property. This product is not intended for use by children without direct adult supervision. Do
not attempt disassembly, use with incompatible components or augment product in any way without the approval
of Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to
read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate
correctly and avoid damage or serious injury.
AGE RECOMMENDATION: NOT FOR CHILDREN UNDER 14 YEARS. THIS IS NOT A TOY.
USING THE MANUAL
This manual is divided into sections to help make assembly easier to understand.
SAFETY WARNINGS AND PRECAUTIONS
Read and follow all instructions and safety precautions before use. Improper use can result in fi re, serious injury and
damage to property.
Components
Use only with compatible components. Should any compatibility questions exist, please refer to the product
instructions, component instructions or contact the appropriate Horizon Hobby offi ce.
Flight
Fly only in open areas to ensure safety. It is recommended fl ying be done at radio control fl ying fi elds. Consult local
ordinances before choosing a fl ying location.
Propeller
Keep loose items that can become entangled in the propeller away from the prop. This includes loose clothing or other
objects such as pencils and screwdrivers. Keep your hands away from the propeller as injury can occur.
Batteries
Always follow the manufacturer’s instructions when using and disposing of any batteries. Mishandling of Li-Po
batteries can result in fi re causing serious injury and damage.
Small Parts
This kit includes small parts and should not be left unattended near children as choking and serious injury could result.
SAFE OPERATING RECOMMENDATIONS
• Inspect your model before every fl ight to ensure it is airworthy.
• Be aware of any other radio frequency user who may present an interference problem.
• Always be courteous and respectful of other users in your selected fl ight area.
• Choose an area clear of obstacles and large enough to safely accomodate your fl ying activity.
• Make sure this area is clear of friends and spectators prior to launching your aircraft.
• Be aware of other activities in the vicinity of your fl ight path that could cause potential confl ict.
• Carefully plan your fl ight path prior to launch.
• Abide by any and all established AMA National Model Aircraft Safety Code.
BEFORE STARTING ASSEMBLY
• Remove parts from bag.
• Inspect fuselage, wing panels, rudder and stabilizer for damage.
• If you fi nd damaged or missing parts, contact your place of purchase.
If you fi nd any wrinkles in the covering, use a heat gun (HAN100) and covering glove (HAN150) or covering iron
(HAN101) with a sealing iron sock (HAN141) to remove them. Use caution while working around areas where the colors
overlap to prevent separating the colors.
• Charge transmitter and receiver batteries.
• Center trims and sticks on your transmitter.
• For a computer radio, create a model memory for this particular model.
• Bind your transmitter and receiver, using your radio system’s instructions.
IMPORTANT: Rebind the radio system once all control throws are set. This will keep the servos from moving to
their endpoints until the transmitter and receiver connect. It will also guarantee the servo reversal settings are
saved in the radio system.
8
Propeller
Halten Sie lose Gegenstände die sich im Propeller verfangen können weg vom Propeller. Dieses gilt auch für Kleidung
oder andere Objekte wie zum Beispiel Stifte oder Schraubendreher.
Halten Sie ihre Hände weg vom Propeller, es besteht akute Verletzungsgefahr.
Akkus
Folgen Sie immer den Herstelleranweisungen bei dem Gebrauch oder Entsorgung von Akkus. Falsche Behandlung von
LiPo Akkus kann zu Feuer mit Körperverletzungen und Sachbeschädigung führen.
Kleinteile
Dieser Baukasten beinhaltet Kleinteile und darf nicht unbeobachtet in der Nähe von Kindern gelassen werden, da die
Teile verschluckt werden könnten mit ernsthaften Verletzung zur Folge.
EMPFEHLUNGEN ZUM SICHEREN BETRIEB
• Überprüfen Sie zur Flugtauglichkeit ihr Modell vor jedem Flug.
• Beachten Sie andere Piloten deren Sendefrequenzen ihre Frequenz stören könnte.
• Begegnen Sie anderen Piloten in ihrem Fluggebiet immer höfl ich und respektvoll.
• Wählen Sie ein Fluggebiet, dass frei von Hindernissen und groß genug ist.
• Stellen Sie vor dem Start sicher, dass die Fläche frei von Freunden und Zuschauern ist.
• Beobachten Sie den Luftraum und andere Flugzeuge/Objekte die ihren Flugweg kreuzen und zu einem Konfl ikt
führen könnten.
• Planen Sie sorgfältig ihren Flugweg vor dem Start.
VOR DEM ZUSAMMENBAU
• Entnehmen Sie zur Überprüfung jedes Teil der Verpackung.
• Überprüfen Sie den Rumpf, Tragfl ächen, Seiten- und Höhenruder auf Beschädigung.
• Sollten Sie beschädigte oder fehlende Teile feststellen, kontaktieren Sie bitte den Verkäufer.
Zum Entfernen von Falten in der Bespannung verwenden Sie den Heißluftfön (HAN100) und Bespannhandschuh
(HAN150) oder das Folienbügeleisen (HAN141). Bitte achten Sie bei überlappenden Farben, dass Sie diese sich bei
dem Bearbeitung nicht trennen.
• Laden des Senders und Empfängers.
• Zentrieren der Trimmungen und Sticks auf dem Sender.
• Sollten Sie einen Computersender verwenden, resetten Sie einen Speicherplatz und benennen ihn nach dem Modell.
• Sender und Empfänger jetzt nach den Bindeanweisung des Herstellers zu binden.
WICHTIG: Wir empfehlen dringend nachdem alle Einstellungen vorgenommen worden sind, das Modell neu zu binden.
Dieses verhindert, dass die Servos in die Endanschläge laufen bevor sich Sender und Empfänger verbunden haben. Es
garantiert auch, dass die Servoreverseeinstellungen in der RC Anlage gesichert sind.
HINWEIS
Alle Anweisungen, Garantien und anderen zugehörigen Dokumente können im eigenen Ermessen von Horizon Hobby,
LLC. jederzeit geändert werden Die aktuelle Produktliteratur fi nden Sie auf horizonhobby.com unter der Registerkarte
„Support“ für das betreffende Produkt.
Spezielle Bedeutungen
Die folgenden Begriffe werden in der gesamten Produktliteratur verwendet, um auf unterschiedlich hohe
Gefahrenrisiken beim Betrieb dieses Produkts hinzuweisen:
HINWEIS: Wenn diese Verfahren nicht korrekt befolgt werden, können sich möglicherweise Sachschäden UND geringe
oder keine Gefahr von Verletzungen ergeben.
ACHTUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich wahrscheinlich Sachschäden UND die
Gefahr von schweren Verletzungen.
WARNUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich wahrscheinlich Sachschäden,
Kollateralschäden und schwere Verletzungen ODER mit hoher Wahrscheinlichkeit oberfl ächliche Verletzungen.
WARNUNG: Lesen Sie die GESAMTE Bedienungsanleitung, um sich vor dem Betrieb mit den Produktfunktionen
vertraut zu machen. Wird das Produkt nicht korrekt betrieben, kann dies zu Schäden am Produkt oder persönlichem
Eigentum führen oder schwere Verletzungen verursachen.
Dies ist ein hochentwickeltes Hobby-Produkt. Es muss mit Vorsicht und gesundem Menschenverstand betrieben
werden und benötigt gewisse mechanische Grundfähigkeiten. Wird dieses Produkt nicht auf eine sichere und
verantwortungsvolle Weise betrieben, kann dies zu Verletzungen oder Schäden am Produkt oder anderen Sachwerten
führen. Dieses Produkt eignet sich nicht für die Verwendung durch Kinder ohne direkte Überwachung eines
Erwachsenen. Verwenden Sie das Produkt nicht mit inkompatiblen Komponenten oder verändern es in jedweder Art
ausserhalb der von Horizon Hobby, LLC vorgegebenen Anweisungen. Diese Bedienungsanleitung enthält Anweisungen
für Sicherheit, Betrieb und Wartung. Es ist unbedingt notwendig, vor Zusammenbau, Einrichtung oder Verwendung
alle Anweisungen und Warnhinweise im Handbuch zu lesen und zu befolgen, damit es bestimmungsgemäß betrieben
werden kann und Schäden oder schwere Verletzungen vermieden werden.
NICHT GEEIGNET FÜR KINDER UNTER 14 JAHREN. DIES IST KEIN SPIELZEUG.
ÜBER DIESE ANLEITUNG
Diese Anleitung ist zur Vereinfachung des Zusammenbaues in Sektionen unterteilt.
WARNUNGEN UND SICHERHEITS-VORKEHRUNGEN
Bitte lesen und befolgen Sie alle Anweisungen und Sicherheitsvorkehrungen vor dem Gebrauch. Falscher, nicht
sachgemäßer Gebrauch kann Feuer, ernsthafte Verletzungen und Sachbeschädigungen zur Folge haben.
Komponenten
Verwenden Sie mit dem Produkt nur kompatible Komponenten. Sollten Fragen zur Kompatibilität auftreten, lesen Sie
bitte die Produkt- oder Bedienungsanweisung oder kontaktieren den Service von Horizon Hobby.
Fliegen
Fliegen Sie um Sicherheit garantieren zu können, nur in weiten offenen Gegenden. Wir empfehlen hier den Betrieb auf
zugelassenen Modellfl ugplätzen. Bitte beachten Sie lokale Vorschriften und Gesetze, bevor Sie einen Platz zum Fliegen
wählen.
9
Ultra Stick
30cc
L’hélice
Gardez éloignés tous les éléments qui pourraient être attrapés par l’hélice. Cela inclut les vêtements larges ou les
objets comme des outils par exemple. Gardez toujours vos mains à distance pour éviter tout cas de blessures.
Les batteries
Suivez toujours les instructions du fabricant de vos batteries. Une mauvaise manipulation d’une batterie Li-Po peut
entraîner un incendie causant de graves dégâts matériels et des blessures corporelles.
Petites pièces
Ce kit contient des petites pièces qui ne doivent pas être laissées à la portée des enfants, ces pièces sont dangereuses
pour eux et peuvent entraîner de graves blessures.
CONSIGNES DE SÉCURITÉ CONCERNANT L’UTILISATION
• Inspectez votre modèle avant chaque vol.
• Surveillez les fréquences utilisées à proximité.
• Soyez toujours courtois et respectueux des autres utilisateurs de la zone de vol.
• Choisissez une zone dégagée de tout obstacle et suffi samment grande pour voler en toute sécurité.
• Contrôlez que la zone est libre de spectateurs avant de lancer votre modèle.
• Soyez conscient des autres activités aux alentours de votre vol, risque de confl it potentiel.
• Planifi ez votre vol avant de le commencer.
AVANT DE COMMENCER L’ASSEMBLAGE
• Retirez toutes les pièces des sachets pour les inspecter.
• Inspectez soigneusement le fuselage, les ailes et les empennages.
• Si un élément est endommagé, contactez votre revendeur.
Si l’entoilage présente quelque plis, vous pouvez les lisser en utilisant le pistolet à air chaud (HAN100) et le gant
(HAN150) ou le fer à entoiler (HAN101) avec la chaussette de protection (HAN141). Agissez soigneusement dans les
zones où plusieurs couleurs d’entoilage sont superposées afi n d’éviter de les séparer.
• ll est recommandé de préparer tous les éléments du système de la radio.
• Cela inclut la charge des batteries comme la mise au neutre des trims et des manches de votre émetteur.
• Si vous utilisez une radio programmable, sélectionnez une mémoire libre afi n d’y enregistrer les paramètres de ce
modèle.
• Nous vous recommandons d’affecter maintenant le récepteur à l’émetteur en suivant les instructions fournies avec
votre radio.
IMPORTANT: Il est hautement recommandé de ré-affecter le système une fois que les courses seront réglées. Cela
empêchera les servos d’aller en butée lors de la connexion du système. Cela garantit également que la direction des
servos est enregistrée dans l’émetteur.
REMARQUE
La totalité des instructions, garanties et autres documents est sujette à modifi cation à la seule discrétion d’Horizon
Hobby, LLC. Pour obtenir la documentation àjour, rendez-vous sur le site horizonhobby.com et cliquez sur l’onglet de
support de ce produit.
Signifi cation de certains termes spécifi ques
Les termes suivants sont utilisés dans l’ensemble du manuel pour indiquer différents niveaux de danger lors de
l’utilisation de ce produit:
REMARQUE: Procédures qui, si elles ne sont pas suivies correctement, peuvent entraîner des dégâts matériels ET
éventuellement un faible risque de blessures.
ATTENTION: Procédures qui, si elles ne sont pas suivies correctement, peuvent entraîner des dégâts matériels ET des
blessures graves.
AVERTISSEMENT: Procédures qui, si elles ne sont pas suivies correctement, peuvent entraîner des dégâts matériels
et des blessures graves OU engendrer une probabilité élevée de blessure superfi cielle.
AVERTISSEMENT: Lisez la TOTALITÉ du manuel d’utilisation afi n de vous familiariser avec les caractéristiques du
produit avant de le faire fonctionner. Une utilisation incorrecte du produit peut entraîner sa détérioration, ainsi que des
risques de dégâts matériels, voire de blessures graves.
Ceci est un produit de loisirs sophistiqué. Il doit être manipulé avec prudence et bon sens et requiert des aptitudes
de base en mécanique. Toute utilisation irresponsable de ce produit ne respectant pas les principes de sécurité peut
provoquer des blessures, entraîner des dégâts matériels et endommager le produit. Ce produit n’est pas destiné à
être utilisé par des enfants sans la surveillance directe d’un adulte. N’essayez pas de modifi er ou d’utiliser ce produit
avec des composants incompatibles hors des instructions fournies par Horizon Hobby, LLC. Ce manuel comporte des
instructions relatives à la sécurité, au fonctionnement et à l’entretien. Il est capital de lire et de respecter la totalité
des instructions et avertissements du manuel avant l’assemblage, le réglage et l’utilisation, ceci afi n de manipuler
correctement l’appareil et d’éviter tout dégât matériel ou toute blessure grave.
14 ANS ET PLUS. CECI N’EST PAS UN JOUET.
UTILISATION DU MANUEL
Ce manuel est divisé en sections pour vous aider à comprendre plus facilement l’assemblage.
AVERTISSEMENTS RELATIFS À LA SÉCURITÉ
Lisez et suivez toutes les instructions relatives à la sécurité avant utilisation. Une utilisation inappropriée peut entraîner
un incendie, de graves blessures et des dégâts matériels.
Composants
Utilisez uniquement des composants compatibles. Si vous avez des questions concernant la compatibilité, référez-vous
à ce manuel ou contactez le service technique Horizon Hobby.
Le vol
Volez uniquement dans des zones dégagées pour un maximum de sécurité. Il est recommandé d’utiliser les pistes des
clubs d’aéromodélisme. Consultez votre mairie pour connaître les sites autorisés.
10
AVVISO
Tutte le istruzioni, le garanzie e gli altri documenti pertinenti sono soggetti a cambiamenti a totale discrezione di
Horizon Hobby, LLC. Per una documentazione aggiornata sul prodotto, visitare il sito www.horizonhobby.com e fare
clic sulla sezione Support per questo prodotto.
Signifi cato dei termini particolari
In tutta la documentazione relativa al prodotto sono utilizzati iseguenti termini per indicare vari livelli di potenziale
pericolo durante il funzionamento:
AVVISO: Procedure che, se non sono seguite correttamente, possono creare danni materiali E nessuna oscarsa
possibilità di lesioni.
ATTENZIONE: Procedure che, se non sono seguite correttamente, possono creare danni materiali E possibili gravi
lesioni.
AVVERTENZA: Procedure che, se non debitamente seguite, espongono alla possibilità di danni alla proprietà fi sica
opossono omportare un’elevata possibilità di provocare ferite superfi ciali. Ulteriori precauzioni per la sicurezza e
avvertenze.
AVVERTENZA: Leggere TUTTO il manuale di istruzioni e prendere familiarità con le caratteristiche del prodotto, prima
di farlo funzionare. Un utilizzo scorretto del prodotto può causare danni al prodotto stesso, alle persone oalle cose,
provocando gravi lesioni.
Questo è un prodotto di hobbistica sofi sticato e NON un giocattolo. È necessario farlo funzionare con cautela e
responsabilità e avere conoscenze basilari di meccanica. Se questo prodotto non è utilizzato in maniera sicura e
responsabile potrebbero verifi carsi lesioni odanni al prodotto stesso oad altre proprietà. Non è un prodotto adatto
aessere utilizzato dai bambini senza la diretta supervisione di un adulto. Non usare componenti non compatibili
o alterare il prodotto in nessuna maniera al di fuori delle istruzioni fornite da Horizon Hobby, LLC. Questo manuale
contiene le istruzioni per un funzionamento e una manutenzione sicuri. È fondamentale leggere e seguire tutte le
istruzioni e le avvertenze del manuale prima di montare, confi gurare ofar funzionare il Prodotto, al fi ne di utilizzarlo
correttamente e di evitare danni olesioni gravi.
MINIMO 14 ANNI. NON È UN GIOCATTOLO.
COME USARE IL MANUALE
Questo manuale è diviso in sezioni per rendere più facile la comprensione del montaggio.
AVVERTIMENTI E PRECAUZIONI PER LA SICUREZZA
Prima dell’uso leggere attentamente tutte le istruzioni e le precauzioni per la sicurezza. In caso contrario si potrebbero
procurare incendi, danni o ferite.
Componenti
Usare solo componenti compatibili. Se ci fossero dubbi riguardo alla compatibilità, è opportuno far riferimento alle
istruzioni relative al prodotto o ai componenti oppure rivolgersi al reparto Horizon Hobby di competenza.
Volo
Per sicurezza volare solo in aree molto ampie. Meglio se in campi volo autorizzati per modellismo. Consultare le
ordinanze locali prima di scegliere luogo dove volare.
Elica
Tenere gli oggetti liberi (vestiti, penne, cacciaviti, ecc.) lontano dall’elica, prima che vi restino impigliati. Bisogna fare
attenzione anche con le mani perché c’è il rischio di ferirsi anche gravemente.
Batterie
Quando si maneggiano o si utilizzano le batterie, bisogna attenersi alle istruzioni del costruttore; il rischio è di procurare
incendi, specialmente con le batterie LiPo, con danni e ferite serie.
Piccole parti
Questo kit comprende delle parti di piccole dimensioni e non lo si può lasciare incustodito se c’è la presenza di bambini
che li possono inghiottire e rimanere soffocati o intossicati.
RACCOMANDAZIONI PER OPERARE IN SICUREZZA
• Controllare attentamente il modello prima di ogni volo per accertarsi che sia idoneo.
• Essere consapevoli che un altro utente della frequenza in uso, potrebbe procurare delle interferenze.
• Essere sempre cortesi e rispettosi nei confronti degli altri utilizzatori dell’area in cui ci si trova.
• Scegliere un’area libera da ostacoli e abbastanza ampia da permettere lo svolgimento del volo in sicurezza.
• Prima del volo verifi care che l’area sia libera da amici e spettatori.
• Stare attenti alle altre attività che si svolgono in vicinanza della vostra traiettoria di volo, per evitare possibili confl itti.
• Pianifi care attentamente il volo prima di lanciare il modello.
• Rispettare sempre scrupolosamente le regole stabilite dall’associazione locale.
PRIMA DI INIZIARE IL MONTAGGIO
• Togliere tutti i pezzi dalla scatola.
• Verifi care che la fusoliera, l’ala e i piani di coda non siano danneggiati.
• Se si trovano parti danneggiate, contattare il negozio da cui è stato acquistato.
Se si trovano delle pieghe nella ricopertura, si possono togliere usando una pistola ad aria calda (HAN100) e guanto per
ricopertura (HAN150), oppure un ferro per ricopertura (HAN101) con la sua calza di protezione (HAN141). Usare cautela
quando si lavora in aree del rivestimento dove ci sono dei colori sovrapposti, per evitare la loro separazione.
• Caricare il trasmettitore e la batteria di volo.
• Centrare stick e trim sul trasmettitore.
• Con una radio computerizzata creare una nuova memoria per questo modello.
• Facendo riferimento alle istruzioni del radiocomando, connettere (bind) trasmettitore e ricevitore.
IMPORTANTE: Ripetere la procedura di connessione una volta regolate le corse, per evitare che i servi vadano a fi ne
corsa. Garantirà anche che le impostazioni di inversione del servo vengano salvate nel sistema radio.
11
Ultra Stick
30cc
BUILDING PRECAUTIONS
During assembly, we recommend resting the parts on a
soft surface such as a soft towel to help prevent denting
the sheeting.
REMOVING WRINKLES
The covering of your model may develop wrinkles during
shipping and will require the use of a heat gun (HAN100)
and covering glove (HAN150) or covering iron (HAN101)
with a sealing iron sock (HAN141) to remove them. Use
caution while working around areas where the colors
overlap to prevent separating the colors. Avoid using
too much heat, which could separate the colors. Placing
a cool damp cloth on adjacent colors will also help in
preventing the separation of the colors while removing
wrinkles.
TRANSPORTATION AND STORAGE
When transporting and storing your model, you will
need a minimum of 80 inches (2m) in length, and 18
inches (46cm) in height to accommodate the size of the
fuselage. We also recommend the use of a wing bag
and stabilizer bags to help protect these surfaces during
transport and storage. The control horns and linkages can
also cause damage to nearby surfaces even when placed
in storage bags. Always place surfaces so the tops are
together to prevent damage from the control horns and
linkages.
OPTIONAL FLOAT INSTALLATION
When installing the recommended fl oats on your Ultra
Stick 30cc, make sure to use the optional fl oat strut
set HAN236519. These struts are longer than those in
the recommended fl oat kit and provide the necessary
propeller clearance for water operation. When installing
the struts, make sure to use the longer struts at the front,
and the shorter struts at the rear. This is necessary to
obtain the correct angle between the wing and fl oats.
HINWEISE ZUM BAU
Während des Zusammenbaus empfehlen wird, dass die
Teile auf einer weichen Oberfl äche, wie einem Handtuch,
abgelegt werden, um ein Eindrücken der Bleche zu
verhindern.
ENTFERNEN VON FALTEN
Während des Transportes können bei der Bespannung
Falten aufgetreten sein. Sie können diese mit dem
Heißluftfön (HAN100) und Bespannhandschuh (HAN150)
oder dem Bügeleisenbezug (HAN141) entfernen. Bitte
achten Sie bei überlappenden Farben diese nicht durch
zuviel Hitze zu lösen. Ein kühlendes Stück Stoff kann hier
neben den Falten aufgelegt helfen, dass die Farben sich
nicht trennen.
TRANSPORT UND LAGERUNG
Bei dem Transport des Modells benötigen Sie mindestens
2 Meter Länge und 46cm Höhe für den Rumpf. Wir
empfehlen ebenfalls Flächen- und Leitwerkstaschen um
Transportschäden zu vermeiden. Durch die Ruderhörner
können ebenfalls Flächen beschädigt werden, so dass
diese nur mit den Oberseiten zueinander gelagert werden
sollten.
OPTIONALE MONTAGE DER SCHWIMMER
Bei der Montage der empfohlenen Schwimmer auf
dem Ultra Stick 30 cc sicherstellen, den optionalen
Schwimmerverstrebungssatz HAN236519 zu verwenden.
Diese Verstrebungen sind länger als die im empfohlenen
Schwimmersatz und bieten den erforderlichen Freiraum
für die Propeller beim Betrieb auf dem Wasser. Bei der
Montage der Verstrebungen sicherstellen, die längeren
Verstrebungen vorne und die kürzen Verstrebungen
hinten anzubringen. Dies ist notwendig, um den korrekten
Winkel zwischen dem Flügel und den Schwimmern zu
erreichen.
PRÉCAUTIONS D’ASSEMBLAGE
Lors de l’assemblage de votre modèle, nous vous
recommandons de poser les pièces sur une surface
douce comme une serviette douce pour éviter d’abîmer
l’entoilage.
ÉLIMINATION DES PLIS
L’entoilage de votre modèle peut développer des plis
lors de l’expédition. Vous pouvez les lisser en utilisant le
pistolet à air chaud (HAN100) et le gant (HAN150) ou le
fer à entoiler (HAN101) avec la chaussette de protection
(HAN141). Soyez vigilant sur les zones où plusieurs
couleurs d’entoilage sont superposées, une température
trop élevée pourrait séparer les couleurs. Placez un
chiffon humide et froid sur les couleurs adjacentes pour
éviter leur séparation lorsque vous enlevez les plis.
TRANSPORT ET STOCKAGE
Lorsque vous transportez ou stockez votre modèle, il
vous faudra un espace d’au moins 2m de longueur et
46cm de hauteur pour accueillir le fuselage. Nous vous
recommandons également l’utilisation d’un sac pour ailes
et de sacs pour stabilisateurs pour les protéger lors du
transport ou stockage. Les guignols et tringleries peuvent
également endommager les gouvernes même dans
les sacs de stockage. Placez toujours les gouvernes de
façon à ce que les parties supérieures soient l’une contre
l’autre pour éviter les contacts et dommages causés par
les guignols ou tringleries.
INSTALLATION DES FLOTTEURS
OPTIONNELS
Lorsque vous installez les fl otteurs recommandés sur
votre Ultra Stick 30cc, assurez-vous de bien utiliser
les haubans de fl otteurs optionnels HAN236519. Ces
haubans sont plus longs que ceux du kit de fl otteurs et
assurent le bon dégagement d’hélice pour une utilisation
sur l’eau. Lors de l’installation des haubans, assurez-vous
bien d’utiliser les haubans les plus longs à l’avant et les
plus courts à l’arrière. Ceci est nécessaire pour obtenir le
bon angle entre l’aile et les fl otteurs.
PRECAUZIONI PER LA COSTRUZIONE
Durante l’assemblaggio noi consigliamo di appoggiare
le varie parti su di una superfi cie morbida come un
asciugamano di spugna per evitare ammaccature al
rivestimento.
TOGLIERE LE GRINZE
rivestimento di questo modello potrebbe sviluppare delle
grinze durante la spedizione e quindi per toglierle, sarà
necessario usare una pistola termica (phon) (HAN100) e
un guanto speciale (HAN150), oppure un ferro apposito
per rivestimenti (HAN101) con la sua calza (HAN141).
Bisogna usare cautela quando si lavora attorno ad
aeree con sovrapposizione di colori per evitare la loro
separazione. Evitare di scaldare troppo per non separare
i colori. Mettere un panno umido fresco sui colori vicini,
aiuta a prevenire la separazione dei colori mentre si
tolgono le grinze.
TRASPORTO E DEPOSITO
Quando si trasporta o si tiene in magazzino questo
modello, sarà necessario uno spazio di 2 metri di
lunghezza e di 46 centimetri in altezza per adattarsi alle
dimensioni della fusoliera. Si consiglia anche di usare
una custodia per proteggere le ali e lo stabilizzatore. Le
squadrette e i rinvii possono pure causare danni alle
superfi ci vicine anche se sono sistemate dentro alle
custodie. Per evitare questo, sistemare le superfi ci in
modo da mettere a contatto le loro parti superiori che non
hanno squadrette o rinvii.
INSTALLAZIONE GALLEGGIANTI
OPZIONALI
Quando si installano i galleggianti consigliati sull’Ultra
Stick 30cc, accertarsi di usare il set di supporti opzionali
HAN236519. Questi supporti sono più lunghi di quelli
contenuti nel kit di galleggianti consigliato e garantiscono
la distanza necessaria tra l’elica e l’acqua. Quando si
installano i supporti, accertarsi di usare quelli più lunghi
davanti e quelli più corti dietro. In questo modo si ottiene
l’angolo corretto tra l’ala e i galleggianti.
12EN
AILERON AND FLAP INSTALLATION
1. Use a 1/16-inch (1.5mm) drill bit to clear the holes of any
debris for the control horn mounting screws.
1.
2.
3.
4.
5.
2. Puncture the covering so the control horn backing plate
can be accessed by the screws.
3. Use a hobby knife to separate the control horn backplate
from the control horn.
4. Insert the three M2 x 25 machine screws into the holes
of the control horn, then into the holes in the aileron.
Make sure the control horn is installed on the bottom of
the aileron.
5. Slide the control horn backplate on the screws. Apply
a small amount of canopy glue on the screws using a
toothpick, then thread the M2 nuts on the screws. Use
a #1 Phillips screwdriver and 4mm nut driver to tighten
the screws.
6.
7.
8.
9.
10.
6. Use side cutters to trim the screws.
7. Use a fi le to lightly fi le any sharp points from the screws
after they have been trimmed. Use care not to contact
the control surface with the fi le. Prepare and install
the fl ap control horns at this time following the same
procedure as the aileron control horns.
8. Use a pin vise and 1/16-inch (1.5mm) drill bit to drill
a hole in the center of each hinge slot to allow the CA
to wick into the hinge. Drill holes in both the wing and
control surfaces at this time. The ailerons and fl aps can
both be prepared during this step.
9. Remove the ailerons from the wing panel. Place a T-pin
in the center of each hinge.
10. Slide the hinges into position with the T-pin resting
against the edge of the control surface.
13 EN
Ultra Stick
30cc
11.
12.
13.
14.
15.
16.
1.
2.
3.
4.
11. Repeat the previous steps to install all four of the aileron
hinges.
16. Check the gap between the fl ap and aileron. Use a thin
ruler (or similar) as a spacer so the gap between the
left and right ailerons and fl aps are the same. Glue the
hinges for the fl aps using thin CA. Once the CA cures,
gently pull on the fi xed surface and control surface to
make sure the hinges are glued securely. If not, apply
additional CA to secure each of the hinges.
12. Fit the aileron to the wing by inserting the hinges into the
slots in the wing.
AILERON AND FLAP SERVO INSTALLATION
1. Remove the aileron servo hatch from the wing. Make
sure to keep the string taped to the wing so it doesn’t fall
into the wing.
13. Check that there is a slight gap between the wing and
the end of the aileron. Use a thin ruler (or similar) as a
spacer so both the left and right ailerons have the same
size gap.
2. Check that the servo mount is glued securely to the
servo cover. If the mount is not secure, use a small
amount of medium CA or epoxy to make sure the mount
is securely fastened to the servo cover.
14. Apply thin CA to the top and bottom of each hinge. Once
the CA cures, gently pull on the fi xed surface and control
surface to make sure the hinges are glued securely. If
not, apply additional CA to secure each of the hinges.
3. Remove the aileron and fl ap cover from the wing. Use a
toothpick to puncture the covering to locate the holes for
the aileron and fl ap cover screws.
15. Prepare the three hinges for the fl ap and place it into
position on the wing.
4. Place the aileron and fl ap cover into position. Use a drill
and 5/32-inch (2mm) drill bit to drill the holes in the
servo cover mounts.
14EN
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
5. Thread an M3 x 15 self-tapping screw into each of the
holes in the aileron and fl ap servo cover mounting holes.
Remove the screws before proceeding.
10. Secure the servo to the cover using a 2mm hex wrench
and the screws provided with the servo.
7. Install the grommets and brass eyelets in the servos.
Follow any instructions included with the servo. Prepare
both fl ap and aileron servos at this time.
12. Secure an 18-inch (460mm) servo extension to the
tip servo using a commercially available fastener
(SPMA3054).
6. Apply a small amount of thin CA to harden the threads
made in the previous step. Allow the CA to fully cure
before installing the aileron servo cover.
11. Center the servo, then secure the servo arm so it is
perpendicular to the servo centerline.
8. Fit the servo between the servo mounting tabs in the
aileron servo tray. The servo arm will be centered in the
slot. Mark the locations for the servo mounting screws
using a pencil, then remove the servo.
9. Use a drill and a 1/16-inch (1.5mm) drill bit to drill the
holes for the servo mounting screws in the locations
marked in the previous step. Use a 2mm hex wrench to
thread a servo mounting screw into each of the holes in
the aileron servo mounting holes. Remove the screws,
then apply a small amount of thin CA to harden the
threads.
13. Tie or tape the string located inside the wing to the end
of the servo lead.
14. Retrieve the servo lead at the wing root. Guide the lead
through the hole in the bottom of the wing.
15 EN
Ultra Stick
30cc
20.
21.
1.
2.
3.
15.
16.
17.
18.
19.
15. Secure the aileron cover in the wing using four M3 x 15
self-tapping screws.
16. Thread an M3 nut on one end of the 100mm pushrod.
Slide a clevis retainer (silicone tubing) on a metal clevis,
then thread the clevis on the rod. Thread a nylon ball end
12-turns on the opposite end of the threaded rod, then
snap the aluminum ball into the ball end using pliers.
17. Attach the ball end to the outer hole of the servo arm
using the hardware included with the servo arm. Make
sure to install the M3 washer (included with the kit)
between the head of the screw and ball end. Tighten the
hardware using a 1/4-inch nut driver and 3/32-inch hex
wrench.
18. Connect the clevis to the outer hole of the control horn.
With the radio on and aileron servo centered, adjust
the link to center the aileron. Once set, slide the clevis
retainer (silicone tubing) over the forks of the clevis, then
tighten the nut against the clevis. Use thread lock on the
nut to prevent it from vibrating loose.
19. Install the fl ap servo and assemble the linkage for the
ap using the same technique as the aileron linkage.
The pushrod for the fl ap linkage also measures 100mm
in length. With the fl ap servo centered, adjust the link
so the fl ap is in the mid-fl ap position of 1
9
/
16
-inches
(40mm).
20. Use the radio system to set the fl ap to the up position.
Use the radio to center the fl ap into the neutral position.
21. Use the radio system to set the fl ap to the down position.
Use the radio to set the full defl ection position.
WING INSTALLATION
1. Slide the wing tube into the wing tube socket.
2. Slide the wing panels together. There will be no gap
between the panels.
3. Fit the dowels on the leading edge of the wing into the
holes in the fuselage.
16EN
4.
1.
2.
3.
4.
5.
6.
7.
8.
9.
4. Place the wing bolt plate on the wing, then thread the
1/4-20 x 13/4-inch nylon wing bolts into the blind nuts in
the fuselage to secure the wing.
STABILIZER INSTALLATION
Î Check the stabilizer mounting surface on the
fuselage to make sure it is flush with the fuselage
sides. If the fuselage sides protrude beyond the
stabilizer mounting surface, then sand them flush.
1. Remove the elevators from the stabilizer. Fit the stabilizer
into the notch in the fuselage. Center the stabilizer.
2. Measure from the tip of the stabilizer to the wing.
Position the stabilizer so both measurements are equal.
3. Check the alignment of the stabilizer to the wing. It
should be equal on both sides of the fuselage.
4. Check all alignments. Mark the outline of the fuselage on
the top of the stabilizer.
5. Use a ruler and carefully cut the covering 1/8 inch (3
mm) inside the line drawn on the stabilizer to remove
the covering from the center of the stabilizer. Remove
the top and bottom covering. Use care not to cut into the
underlying wood, weakening the stabilizer.
6. Use a paper towel and isopropyl alcohol to remove the
lines from the stabilizer.
7. Mix 1/2 ounce (15ml) of 30-minute epoxy. Use an epoxy
brush to apply epoxy to the exposed wood on the top of
the stabilizer.
8. Use an epoxy brush to apply epoxy to the stabilizer
mounting surface in the notch in the fuselage for the
stabilizer.
9. Fit the stabilizer back into position. Check the alignment
following steps 1 through 3, then use a paper towel and
isopropyl alcohol to remove any excess epoxy from the
fuselage and stabilizer.
17 EN
Ultra Stick
30cc
5.
6.
7.
8.
1.
10.
1.
2.
3.
4.
10. Use clamps to hold the stabilizer in position. Allow the
epoxy to fully cure before proceeding.
FIN INSTALLATION
1. Fit the fi n into the slot in the fuselage. Use a ruler to
check the alignment of the fi n to the rear edge of the
fuselage.
2. Use a felt-tipped pen to trace the outline of the fi n on the
top of the fuselage. Also mark the bottom of the fi n along
the fuselage.
3. Use a hobby knife with a #11 blade to carefully remove
the covering 1/8-inch (3mm) inside the lines drawn from
the top of the fuselage at the rear of the fi n.
4. Use a hobby knife with a #11 blade to carefully remove
the covering 1/8-inch (3mm) inside the lines drawn from
the top of the fuselage at the front of the fi n.
5. Use a ruler and carefully cut the covering 1/8 inch (3
mm) below the line drawn on the fi n. Remove the bottom
covering. Use care not to cut into the underlying wood,
weakening the fi n.
6. Mix 1/2 ounce (15ml) of 30-minute epoxy. Use an epoxy
brush to apply the epoxy in the slot for the fi n and to the
exposed wood on the top of the fuselage.
7. Apply epoxy to the exposed wood on the bottom of the
n where it comes in contact with the fuselage.
8. Fit the fi n in position. Check that it is square to the
fuselage. Use tape if necessary to hold the fi n in position
until the epoxy fully cures.
ELEVATOR INSTALLATION
1. Attach the control horns to the top of the elevators
following the same procedure as the aileron and fl ap
control horns.
18EN
2.
3.
4.
1.
2.
3.
4.
5.
6.
7.
2. Drill a 1/16-inch (1.5mm) hole in the center of each
hinge slot for in both the elevator and stabilizer. Prepare
and install the elevator hinges, then fi t the elevator to the
stabilizer. Check that the ends of the elevator aligns with
the ends of the stabilizer.
3. Check to make sure the control horn is on the top of the
elevator, and that the trim scheme from the elevator and
stabilizer are on the same side.
4. Repeat the previous steps to install the remaining
elevator. Glue the hinges at this time following the same
procedure as the aileron and fl ap hinges. Once the CA
cures, gently pull on the fi xed surface and control surface
to make sure the hinges are glued securely. If not, apply
additional CA to secure each of the hinges.
RUDDER AND TAIL WHEEL INSTALLATION
1. Use a 1.5mm hex wrench to loosen the setscrews in the
wheel collar for the tail wheel. Slide the wheel collar as
close to the tail wheel as possible.
2. Lightly sand the tail wheel wire where it contacts the
rudder. Use a paper towel and isopropyl alcohol to
remove any oil or debris from the wire.
3. Mix a small amount of 15-minute epoxy. Use a toothpick
to apply epoxy to the rudder where the tail wheel wire
will come in contact with the exposed wood.
4. Use a toothpick to apply epoxy to the tail wheel wire
where it contacts the rudder.
5. Fit the wire into the rudder. Use a paper towel and
isopropyl alcohol to remove any excess epoxy from the
rudder and wire.
6. Use low-tack tape to hold the tail wheel wire in position
until the epoxy fully cures. Once cured, remove the tape
from the rudder.
7. Install the control horn on the rudder. Note the control
horn will be on the left side of the rudder.
19 EN
Ultra Stick
30cc
8.
9.
10.
11.
12.
1.
2.
3.
4.
5.
8. Prepare the hinge slots and hinges for the rudder. Install
the hinges and fi t the rudder to the fi n. Align the top of
the fi n and rudder. Use thin CA to glue the hinges. Once
the CA cures, gently pull on the fi xed surface and control
surface to make sure the hinges are glued securely. If
not, apply additional CA to secure each of the hinges.
9. Position the tail wheel bracket so it is centered on the
bottom of the stabilizer. Use a felt-tipped pen to mark the
location for the mounting screws. Use a drill and 5/32-
inch (2mm) drill bit to drill the holes for the screws.
10. Use a #1 Phillips screwdriver to thread the M3 x 20 self-
tapping screws into the holes. Remove the screws, then
apply thin CA into the holes to harden the threads. Once
the CA has fully cured, install the three screws to secure
the tail wheel bracket to the stabilizer.
11. Slide the wheel collar against the tail wheel bracket and
tighten the setscrew using a 1.5mm hex wrench.
12. Attach the tail wheel to the wire using a 3mm wheel
collar and 3mm setscrew. Apply thread lock to the
setscrew, then tighten the setscrew using a 1.5mm hex
wrench.
Î Use the foam tail wheel for quieter operation
when using EP power systems from asphalt runways,
or the rubber tail wheel for grass runways.
RADIO INSTALLATION
1. Prepare the rudder and elevator servos by installing the
rubber grommets and brass eyelets. Install the elevator
(1) and the rudder (2) servos in the fuselage with the
output of the servos facing the front of the fuselage.
Î Servo location may vary in the
production version of your aircraft.
2. Secure the receiver in the fuselage using two-sided
tape and a hook and loop strap. Connect the rudder and
elevator servos to the receiver.
Î When using the recommended receiver,
make sure it is secure and installed according to
the instructions provided with the receiver.
3. Use a hobby knife with a #11 blade to remove the
covering from the side of the fuselage for the receiver
switch. Mount the switch and connect it to the receiver.
4. Use hook and loop tape to secure one remote receiver as
far forward in the fuselage as possible.
5. The second remote receiver is mounted as far back as
possible using hook and loop tape.
20EN
10.
11.
12.
13.
14.
6.
6. Mount the receiver battery in the fuselage using hook
and loop tape. Make a brace from mixing sticks to keep
the battery secure in the fuselage.
Î The ignition battery can be mounted in the
same location when a gas engine is being used.
Connect a 6-inch (150mm) extension to the battery
to connect it to the ignition switch when installed.
Î Reposition the batteries as necessary to
achieve the correct Center of Gravity depending
on your engine or motor selection.
7. Slide the 36-inch (914mm) threaded pushrod into the
pushrod tube in the fuselage. Guide the pushrod out the
exit at the rear of the fuselage.
8. Thread an M3 nut on the pushrod. Slide a clevis retainer
(silicone tubing) on a metal clevis, then thread the clevis
on the pushrod. Prepare the rudder servo horn and install
it on the rudder servo. Connect the clevis to the servo
arm.
9. Thread an M3 nut on the pushrod. Slide a clevis retainer
(silicone tubing) on a metal clevis, then thread the clevis
on the pushrod. Connect the clevis to the center hole of
the rudder control horn. With the radio system on and
rudder servo centered, adjust the clevises to center the
rudder. Once centered, slide the retainers over the forks
of the clevises, then tighten the nuts against the clevises.
Use thread lock on the nuts to prevent them from
vibrating loose.
10. Thread a nylon ball end on the 35
1
/
2
-inch (900mm)
elevator pushrod, then snap the ball into the ball end.
Slide a 3mm washer on an M3 x 12 socket head cap
screw, then thread the screw into the outer hole of the
elevator servo arm.
11. Slide a 3mm washer on the screw, then a 3mm lock
nut. Use a 2.5mm hex wrench and 5.5mm nut driver to
tighten the hardware. Prepare both elevator pushrod at
this time.
12. Slide the pushrod into the tubes, guiding out of the
fuselage near the elevators. Center the elevator servos
and attach the servo arms to the servos.
13. Use an M3 nut, metal clevis and clevis retainer (silicone
tubing) to prepare the ends to attach the pushrods to the
elevator control horns. Center the servos and adjust the
clevises to center the elevators. Slide the retainer over
the forks of the clevis and tighten the nut the against the
clevis after applying thread lock to the nut.
Î When using heavier engines, it may be necessary
to mount the elevator servos at the rear of the fuselage.
Follow the steps covering this optional installation.
14. Connect an 18-inch (460mm) extension to the elevator
servo. Remove the covering using a hobby knife and #11
blade. Mount the elevator servo in the fuselage with the
output facing toward the front of the fuselage.
7.
8.
9.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84

Hangar 9 HAN2365 Le manuel du propriétaire

Catégorie
Jouets télécommandés
Taper
Le manuel du propriétaire
Ce manuel convient également à