Hatco FSHC-6W, FSHC-7 Series Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
Flav-R-Savor
®
Portable Holding Cabinets
Armoires de conservation portables
FSHC-6W and FSHC-7 Series/Série
Installation and Operating Manual
Manuel d'installation et d'utilisation
P/N 07.04.377.00 © 2017 Hatco Corporation
Register Online!
(see page 2)
S'inscrire en ligne!
(voir page 16)
hatcocorp.com
Do not operate this equipment unless you
have read and understood the contents of
this manual! Failure to follow the
instructions contained in this manual may
result in serious injury or death. This
manual contains important safety
information concerning the maintenance,
use, and operation of this product. If
you’re unable to understand the contents
of this manual, please bring it to the
attention of your supervisor. Keep this
manual in a safe location for future
reference.
English = p 2
No opere este equipo al menos que haya
leído y comprendido el contenido de este
manual! Cualquier falla en el seguimiento
de las instrucciones contenidas en este
manual puede resultar en un serio lesión
o muerte. Este manual contiene
importante información sobre seguridad
concerniente al mantenimiento, uso y
operación de este producto. Si usted no
puede entender el contenido de este
manual por favor pregunte a su
supervisor. Almacenar este manual en
una localización segura para la referencia
futura.
Ne pas utiliser cet équipement sans avoir
lu et compris le contenu de ce manuel !
Le non-respect des instructions
contenues dans ce manuel peut entraîner
de graves blessures ou la mort. Ce
manuel contient des informations
importantes concernant l'entretien,
l'utilisation et le fonctionnement de ce
produit. Si vous ne comprenez pas le
contenu de ce manuel, veuillez le signaler
à votre supérieur. Conservez ce manuel
dans un endroit sûr pour pouvoir vous y
référer plus tard.
Français = p 16
WARNING
ADVERTENCIA
AVERTISSEMENT
Form No. FSHC67M-0117
2
English
S
af
et
y i
nf
ormat
i
on t
hat
appears i
n t
hi
s manual
i
s i
dent
i
f
i
ed by
the
fol
l
owi
ng s
i
gnal
word panel
s
:
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE is used to address practices not related to personal
injury.
WARNING
NOTICE
CAUTION
INTRODUCTION
Hatco Flav-R-Savor
®
Portable Holding Cabinets are designed to
hold prepared foods for prolonged periods of time while
maintaining that “just-made” quality. They provide the best
environment for food products by regulating the air temperature
while at the same time balancing the humidity level. The use of
controlled, moisturized heat maintains serving temperature and
food texture longer than conventional dry holding equipment.
The Flav-R-Savor air flow pattern is designed to maintain
consistent cabinet temperature without drying out foods. The
precise combination of heat and humidity creates a “blanket”
effect around the food. The air flow rate enables the cabinet to
rapidly recover temperature after opening and closing the door.
Flav-R-Savor Portable Holding Cabinets are products of
extensive research and field testing. The materials used were
selected for maximum durability, attractive appearance, and
optimum performance. Every unit is inspected and tested
thoroughly prior to shipment.
This manual provides the installation, safety, and operating
instructions for a Flav-R-Savor Portable Holding Cabinet. Hatco
recommends all installation, operating, and safety instructions
appearing in this manual be read prior to installation or
operation of the unit.
Important Owner Information ..............................................2
Introduction...........................................................................2
Important Safety Information...............................................3
Model Description.................................................................4
Model Designation................................................................4
Specifications........................................................................5
Plug Configuration ...............................................................5
Electrical Rating Chart .........................................................5
Dimensions ..........................................................................7
Installation .............................................................................8
General ................................................................................8
Reversing the Access Door .................................................9
Operation.............................................................................10
General ..............................................................................10
Food Holding Guide ...........................................................11
Maintenance ........................................................................11
General ..............................................................................11
Daily Cleaning....................................................................12
Cleaning/Draining the Water Reservoir .............................12
Removing Lime and Mineral Deposits...............................12
Troubleshooting Guide ......................................................13
Options and Accessories...................................................14
Limited Warranty.................................................................15
Authorized Parts Distributors............................Back Cover
IMPORTANT OWNER INFORMATION
Record the model number, serial number, voltage, and
purchase date of the unit in the spaces below (specification
label located on the back of the unit). Please have this
information available when calling Hatco for service assistance.
Model No. ________________________________________
Serial No. ________________________________________
Voltage __________________________________________
Date of Purchase __________________________________
Register your unit!
Completing online warranty registration will prevent delay in
obtaining warranty coverage. Access the Hatco website at
www.hatcocorp.com, select the Parts & Service pull-down
menu, and click on “Warranty Registration”.
Business
Hours: 7:00
AM to 5:00 PM
Central Standard Time (CST)
(Summer Hours: June to September –
7:00
AM to 5:00 PM CST Monday through Thursday
7:00
AM to 4:00 PM CST Friday)
Telephone: 800-558-0607; 414- 671-6350
E-mail: partsandservice@hatcocorp.com
Additional information can be found by visiting our web site at
www.hatcocorp.com.
24 Hour 7 Day Parts and Service
Assistance available in the United States
and Canada by calling 800-558-0607.
CONTENTS
Form No. FSHC67M-0117
3
IMPORTANT SAFETY INFORMATION
English
Make sure all operators have been instructed on the safe
and proper use of the unit.
This unit is not intended for use by children or persons
with reduced physical, sensory, or mental capabilities.
Ensure proper supervision of children and keep them away
from the unit.
This unit has no “user-serviceable” parts. If service is
required on this unit, contact an Authorized Hatco Service
Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350.
BURN HAZARD:
• Some exterior surfaces on unit will get hot. Use caution
when touching these areas.
• Turn off unit and allow it to cool before draining water
from water reservoir.
Locate unit in an area that is convenient for use. The
location should be level to prevent unit or its contents from
falling accidentally and strong enough to support the
weight of the unit and contents.
Do not overfill water reservoir. Overfilling can cause water
to leak onto floor and create a slipping hazard.
Transport unit in upright position only. Make sure all water
is drained prior to transport.
Do not lay unit on side with control panel or damage to unit
could occur. Make sure all water is drained prior to laying
unit on its side.
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch finish of unit, marring
its appearance and making it susceptible to soil
accumulation.
Use of distilled water in the water reservoir of humidified
units is recommended to preserve the life of electrical and
mechanical components. If non-distilled water is used, the
reservoir will require periodic cleaning and deliming (refer
to the MAINTENANCE section for cleaning procedure). Unit
failure due to lime or mineral deposits is not covered under
warranty.
Do not use deionized or reverse osmosis water. It will
shorten the life of the water pan and heating element.
Clean unit daily to avoid malfunctions and maintain
sanitary operation.
NOTICE
CAUTION
WARNING
ELECTRIC SHOCK HAZARD:
• Plug unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. If
plug and receptacle do not match, contact a qualified
electrician to determine and install proper voltage and
size electrical receptacle.
• Turn OFF power switch, unplug power cord, and allow
unit to cool before performing any cleaning,
adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Unit is not weatherproof. Locate unit indoors where
ambient air temperature is a minimum of 70°F (21°C).
• This unit is not “jet-proof” construction. Do not use jet-
clean spray to clean this unit.
• Do not steam clean or use excessive water on unit.
• Turn power switch OFF and allow unit to cool before
draining water reservoir.
• Do not pull unit by power cord.
• Discontinue use if power cord is frayed or worn.
• Do not attempt to repair or replace a damaged power
cord. Cord must be replaced by Hatco, an Authorized
Hatco Service Agent, or a person with similar
qualifications.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
FIREHAZARD: Locate unit a minimum of 1″ (25 mm) from
combustible walls and materials. If safe distances are not
maintained, combustion or discoloration could occur.
Make sure food product has been heated to the proper
food-safe temperature before placing in unit. Failure to
heat food product properly may result in serious health
risks. This unit is for holding pre-heated food product only.
Hatco Corporation is not responsible for actual food
product serving temperature. It is the responsibility of the
user to ensure that food product is held and served at a
safe temperature.
WARNING
Read the following important safety information before using this equipment to avoid
serious injury or death and to avoid damage to equipment or property
.
Form No. FSHC67M-0117
4
MODEL DESCRIPTION
English
All Models
The Flav-R-Savor
®
Portable Holding Cabinet is constructed of
sturdy stainless steel and powdercoat painted top, sides and
back. It features thermostatically-controlled heat, low velocity
convected air, a humidity system, and a large aluminum framed
tempered glass door (heavy-duty insulated stainless steel door
also available for FSHC-6W1 model). The access door can be
hinged left or right, depending on the application. Controls are
easily accessible and include a POWER ON/OFF (I/O) switch
and a digital temperature display. The unit is made portable by
using 4″ (102 mm) casters—the front two being swivel casters
with wheel locks. Units come standard in silver gray, are
available in optional stainless steel or black, and can be
configured without a humidity system. An attached 6′
(1829 mm) power cord and plug is standard.
A stacking option is available to allow the placement of one unit
on top of another. Refer to the OPTIONS AND ACCESSORIES
section for details on all available options.
FSHC-6W1 Model
The FSHC-6W1 is a single door model made to fit under lower
work counters. The cabinet is equipped with six pairs of angle
pan shelves. These pan shelves are designed to hold full size
sheet pans, several steam table pan sizes (full, half, and third),
and Gastronorm pans.
A non-humidified model is also available. Non-humidified units
come with a heavy-duty, vented stainless steel door and a four
shelf rack. The non-humidified model is for countertop mounting
only and is shipped without casters or legs.
FSHC-6W2 Model
The FSHC-6W2 has all the features of the humidified
FSHC-6W1, but is equipped with two doors for pass through
operation.
FSHC-6W2 Model
FSHC-7-1 Models
The FSHC-7-1 is a single door model. The cabinet is equipped
with seven pairs of angle pan shelves. These pan shelves are
designed to hold full size sheet pans, several steam table pan
sizes (full, half, and third), and Gastronorm pans.
FSHC-7-2 Models
The FSHC-7-2 has all the features of the FSHC-7-1, but is
equipped with two doors for pass through operation.
FSHC-7-1 Model
MODEL DESIGNATION
F S H C - X W - X
Flav-R-Savor
Holding Cabinet
Full Size Sheet Pan Capacity
W = Wide Cabinet Capacity
No Character = Standard Width
Number of Doors
Model Voltage Watts Amps Hertz Plug Configuration
FSHC-6W1 and
FSHC-6W2
(Humidified)
120 1697 14.1 60 NEMA 5-15P*
220 1697 7.7 50
CEE 7/7 Schuko
240 1697 7.1 50
BS-1363, AS 3112
220–230 (CE) 1697–1850 7.7–8.0 50
CEE 7/7 Schuko
230–240 (CE) 1562–1697 6.8–7.1 50
BS-1363
FSHC-6W1 and
FSHC-6W2
(non-Humidified)
120 1097 9.2 60 NEMA 5-15P
FSHC-7-1 and
FSHC-7-2
(Humidified)
120 1697 14.1 60 NEMA 5-15P*
220 1697 7.7 50
CEE 7/7 Schuko
240 1697 7.1 50
BS-1363, AS 3112
220–230 (CE) 1697–1850 7.7–8.0 50
CEE 7/7 Schuko
230–240 (CE) 1562–1697 6.8–7.1 50
BS-1363
FSHC-7-1 and
FSHC-7-2
(non-Humidified)
120 1097 9.2 60 NEMA 5-15P
220 1093 5 50
CEE 7/7 Schuko
240 1101 4.6 50
BS-1363, AS 3112
220–230 (CE) 1093–1195 5.0–5.2 50
CEE 7/7 Schuko
230–240 (CE) 1011–1097 4.4–4.6 50
BS-1363
Form No. FSHC67M-0117
5
SPECIFICATIONS
English
Electrical Rating Chart — Standard Wattage
Plug Configuration
Units are supplied from the factory with an electrical cord and
plug installed.
ELECTRIC SHOCK HAZARD: Plug unit into a properly
grounded electrical receptacle of the correct voltage, size,
and plug configuration. If the plug and receptacle do not
match, contact a qualified electrician to determine and
install the proper voltage and size electrical receptacle.
NOTE: The specification label is located on the back of the unit.
See label for serial number and verification of unit
electrical information.
WARNING
Plug Configurations
NOTE: Receptacle not supplied by Hatco.
NEMA 5-15P
CEE 7/7 Schuko AS 3112
BS-1363
NEMA 5-20P
The shaded areas contain electrical information for International models only.
* NEMA 5-20P for Canada.
Shipping Weights
FSHC-6W1: 185 lbs. (84 kg)
FSHC-6W2: 190 lbs. (86 kg)
FSHC-7-1: 175 lbs. (79 kg)
FSHC-7-2: 180 lbs. (82 kg)
Model Voltage Watts Amps Hertz Plug Configuration
FSHC-6W1 and
FSHC-6W2
(Humidified)
220 2047 9.3 50
CEE 7/7 Schuko
240 2047 8.5 50
BS-1363, AS 3112
220–230 (CE) 2047–2233 9.3–9.7 50
CEE 7/7 Schuko
230–240 (CE) 1884–2047 8.2–8.5 50
BS-1363
FSHC-6W1 and
FSHC-6W2
(non-Humidified)
120 1440 12 60 NEMA 5-15P*
FSHC-7-1 and
FSHC-7-2
(Humidified)
220 2047 9.3 50
CEE 7/7 Schuko
240 2047 8.5 50
BS-1363, AS 3112
220–230 (CE) 2047–2233 9.3–9.7 50
CEE 7/7 Schuko
230–240 (CE) 1884–2047 8.2–8.5 50
BS-1363
FSHC-7-1 and
FSHC-7-2
(non-Humidified)
120 1440 12 60 NEMA 5-15P*
220 1447 6.6 50
CEE 7/7 Schuko
240 1447 6 50
BS-1363, AS 3112
220–230 (CE) 1447–1581 6.6–6.9 50
CEE 7/7 Schuko
230–240 (CE) 1328–1447 5.8–6 50
BS-1363
Form No. FSHC67M-0117
6
SPECIFICATIONS
English
Electrical Rating Chart — High Wattage
The shaded areas contain electrical information for International models only.
* NEMA 5-20P for Canada.
Shipping Weights
FSHC-6W1: 185 lbs. (84 kg)
FSHC-6W2: 190 lbs. (86 kg)
FSHC-7-1: 175 lbs. (79 kg)
FSHC-7-2: 180 lbs. (82 kg)
Form No. FSHC67M-0117
7
SPECIFICATIONS
English
Model
Width
(A)
Depth
(B)
Height
(C)†
FSHC-6W1
25-3/8″
(645 mm)
29-5/8″
(753 mm)
32-1/8″
(816 mm)
FSHC-6W2
25-3/8″
(645 mm)
32″
(813 mm)
32-1/8″
(816 mm)
Interior Capacity
Top Surface: 25-3/8" W x 25-7/8" D (645 x 657 mm)
Cabinet Opening: 20-7/8" W x 19" H (530 x 483 mm)
Model
Width
(A)
Depth
(B)
Height
(C)*
FSHC-7-1
22-3/4″
(578 mm)
29-5/8″
(753 mm)
35-1/8″
(892 mm)
FSHC-7-2
22-3/4″
(578 mm)
32″
(813 mm)
35-1/8″
(892 mm)
Interior Capacity
Top Surface: 22-3/4" W x 25-7/8" D (578 x 657 mm)
Cabinet Opening: 18-1/4" W x 22-1/8" H (464 x 562 mm)
Dimensions — FSHC-6W Series
Front View Side View
A
B
C
Dimensions — FSHC-7 Series
† Includes 4" (102 mm) diameter casters; height is 29-3/4" (756 mm) with low profile casters installed.
* Includes 4" (102 mm) diameter casters; height is 32-3/4" (832 mm) with low profile casters installed;
height is 34" (864 mm) with 4" (102 mm) legs installed; height is 36" (915 mm) with 6" (152 mm) legs installed.
Form No. FSHC67M-0117
8
INSTALLATION
English
General
Flav-R-Savor
®
Portable Holding Cabinets are shipped with most
components installed and ready for operation. The following
installation instructions must be performed before plugging in
and operating the cabinet.
ELECTRIC SHOCK HAZARD: Unit is not weatherproof.
Locate the unit indoors where the ambient air temperature
is a minimum of 70°F (21°C).
FIRE HAZARD: Locate unit a minimum of 1″ (25 mm) from
combustible walls and materials. If safe distances are not
maintained, combustion or discoloration could occur.
Locate unit in an area that is convenient for use. The
location should be level to prevent unit or its contents from
falling accidentally and strong enough to support the
weight of the unit and contents.
1. Remove the unit from the carton.
2. Remove all loose items shipped inside the cabinet such as
the box containing the adjustable pan shelves, the
casters/legs, etc...
NOTE: To prevent delay in obtaining warranty coverage,
complete online warranty registration. See the
IMPORTANT OWNER INFORMATION section for
details.
3. Remove tape and protective packaging from all surfaces of
the unit.
NOTE: If 4″ (102 mm) leg or 6″ (152 mm) leg installation is
required, refer to the OPTIONS AND ACCESSORIES
section in this manual for installation instructions.
WARNING
CAUTION
4. Install the 4″ (102 mm) casters onto the bottom of the cabinet.
A low profile caster option is available for the FSHC-6W
series—use the same procedure below to install.
Do not lay unit on side with control panel or damage to unit
could occur. Make sure all water is drained prior to laying
unit on its side.
a. Carefully lay the unit on its back side. This step requires
two people.
NOTE: Place a piece of cardboard between the cabinet and the
floor to prevent marring the cabinet finish.
b Install the two swivel casters to the front of the unit using
four mounting screws (provided). Tighten securely.
c. Install the two stationary casters to the back of the unit
using four mounting screws (provided). Tighten securely.
d. Return the unit to its upright position. This step requires
two people.
5. Unpack the adjustable pan shelves from the box and install
them inside the cabinet. There are twelve or fourteen
adjustable pan shelves—half on each side of the cabinet.
Four shelf support pins, two on each side of the cabinet,
support the pan shelves.
To install each pan shelf:
a. Align the adjustable pan shelf hooks with the desired
slots on the front and rear shelf supports.
b. Drop the adjustable shelf hooks on top of the desired
shelf support pin on each end of the shelf supports.
6. Place the unit in the desired location.
• Locate the unit in an area where the ambient air
temperature is constant and a minimum of 70°F (21°C).
Avoid areas that may be subject to active air movements
or currents (i.e., near exhaust fans/hoods, exterior doors,
and air conditioning ducts).
• Make sure the unit is located on solid, level flooring.
• Make sure the unit is at the proper height in an area
convenient for use.
NOTICE
Mounting Screw
4" (102 mm) Swivel Caster
Adjustable
Pan Shelf
Drop Adjustable Pan Shelf Hook
over the Shelf Support Pin
to secure Adjustable Pan Shelf.
Shelf
Support
Shelf
Support
Pin
Installing the Components
Form No. FSHC67M-0117
9
INSTALLATION
English
Reversing the Access Door
Doors are shipped from the factory hinged on the left side of
the cabinet, opening from the right. Use the following procedure
to reverse the door to open from the left.
1. Remove the top hinge screw.
2. Tip the door forward (away from cabinet) and lift gently to
clear the bottom hinge bracket. Make sure to locate and
save the nylon washer.
3. Reinstall the hinge screw that was removed in the first step.
4. Remove the hinge bracket screws securing each hinge
bracket to the cabinet.
5. Remove the hinge cover screws and hinge cover from the
right side of the cabinet and install them into the left-side
screw holes.
6. Reinstall the hinge bracket on the right side of cabinet.
7. Rotate the door 180°.
8. Remove the hinge screw from the end of the door now at
the top.
9. Place the door assembly into the bottom hinge bracket.
NOTE: Nylon washer must be installed between the door and
the bottom hinge bracket.
10. Tip/tilt the door assembly towards the cabinet and align the
door top with the hinge bracket. Reinstall the top hinge
screw through the top hinge bracket and into the door.
Tighten securely.
11. Remove the door handle by removing the door handle
screws from the backside of the door.
12. Remove the door plug from the top hole of the door.
13. Install the door plug into the bottom hole of the door by
pressing firmly.
14. Install the handle by aligning the screw holes on the handle
to the screws in the top two holes of the door.
Glass
Access Door
Hinge Screw
Hinge Bracket Screws
Hinge Bracket
Hinge Cover
Hinge
Cover
Screws
Nylon
Washer
Removing the Access Door
Hinge
Bracket Screws
Nylon Washer Nylon Washer
Hinge Cover
Hinge Cover Screws
Handle Screws
Door
Handle
Hinge Bracket
Door
Plug
Hinge Screw
Reversing and Installing the Access Door
Form No. FSHC67M-0117
10
OPERATION
English
General
Use the following procedures to operate a Flav-R-Savor
®
Portable Holding Cabinet.
Read all safety messages in the IMPORTANT SAFETY
INFORMATION section before operating this equipment.
Startup
1. Plug the unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. See the
SPECIFICATIONS section for details.
2. Move the POWER ON/OFF (I/O) switch to the ON (I)
POSITION. The heating system will start up.
• The CABINET TEMPERATURE monitor will show the
current temperature of the cabinet.
• The LOW WATER indicator will illuminate until the water
reservoir is filled.
BURN HAZARD: Some exterior surfaces on the unit will get
hot. Use caution when touching these areas.
Use of distilled water in the water reservoir of humidified
units is recommended to preserve the life of electrical and
mechanical components. If non-distilled water is used, the
reservoir will require periodic cleaning and deliming (refer
to the MAINTENANCE section for cleaning procedure). Unit
failure due to lime or mineral deposits is not covered under
warranty.
Do not use deionized or reverse osmosis water. It will
shorten the life of the water pan and heating element.
NOTE: Unit failure caused by deionized or reverse osmosis
water is not covered by warranty.
3. On humidified units, fill the water
reservoir with clean water. To fill the
reservoir:
a. Verify drain valve is in closed
position.
b. Lift up the WATER FILL cup cover
and pull forward.
c. Slowly pour the water into the cup until the LOW
WATER indicator no longer illuminates.
NOTE: On the initial fill, the water reservoir capacity is 80
ounces or 2-1/2 quarts (2.3 liters).
Drain Valve Positions
WARNING
NOTICE
CAUTION
WATER
FILL Cup
Valve
Open
Valve
Closed
Do not overfill water reservoir. Overfilling can cause
electrical shock.
Controls
4. On humidified units, set the HUMIDITY Control to the desired
level. See the “Food Holding Guide” for recommendations.
• The HUMIDITY CYCLE indicator will illuminate until the
interior of the cabinet reaches the selected humidity
setting.
The reservoir capacity permits uninterrupted operation for
approximately 4-8 hours, depending on the settings and how
frequently the door is opened. When the red Low Water
Indicator is lit, add water to the reservoir. The water reservoir
refill capacity is approximately 48 ounces (1.5 liters).
WARNING! Electric Shock Hazard—Do not overfill water
reservoir.
5. Set the TEMPERATURE Control to the desired temperature.
See the “Food Holding Guide” for recommendations.
6. Allow 30 minutes to preheat the cabinet with a full pan of
water before loading preheated food product.
• The CABINET TEMPERATURE Monitor shows the
current temperature inside the cabinet.
NOTE: Temperature and humidity settings may vary depending
upon product make-up and consistency. The cabinet
temperature indicator displays the lowest temperature
point inside the cabinet, not the product temperature.
NOTE: FSHC-7 Series units can be factory equipped with an
optional audible Low Water alarm. Add water to the
reservoir until the alarm shuts off.
Make sure food product has been heated to the proper
food-safe temperature before placing in unit. Failure to heat
food product properly may result in serious health risks.
This unit is for holding pre-heated food product only.
Shutdown
1. Move the POWER ON/OFF (I/O) Switch to the OFF (O)
position and allow the unit to cool.
2. Perform the “Daily Cleaning” procedure in the
MAINTENANCE section of this manual.
TEMPERATURE
Control
POWER
ON/OFF (I/O)
Switch
HUMIDITY
Control
HUMIDITY CYCLE
Indicator
LOW WATER
Indicator
CABINET
TEMPERATURE
Monitor
WARNING
WARNING
Form No. FSHC67M-0117
11
OPERATION
English
Type of Food
Maximum
Holding Time
Humidity
Setting
Air Temperature Setting
°F °C
Bagels 3 Hours Low 140 60
Biscuits 2 Hours Medium 130 54
Chicken (Pieces) 5 Hours High 175 79
Chicken (Whole) 2 Hours High 180 82
Croissants 3 Hours Low 140 60
Fish 1 Hour Medium 180 82
Frankfurters 2 Hours High 185 85
Fruit Pies 3-1/2 Hours Medium 140 60
Hot Dogs (Appetizers) 4 Hours High 175 79
Onion Rings 1 Hour Low 140 60
Pizza 1 Hour Medium 185 85
Pretzels 3 Hours Medium 140 60
Ribs 2 Hours High 185 85
Wrapped Sandwiches 2 Hours Medium 160 71
NOTE: All times and settings are recommendations only and may vary depending on product preparation, cooking time, and
internal food temperature.
Food Holding Guide
General
Flav-R-Savor Portable Holding Cabinets are designed for
maximum durability and performance with minimum maintenance.
ELECTRIC SHOCK HAZARD:
• Turn OFF power switch, unplug power cord, and allow
unit to cool before performing any cleaning,
adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Unit is not weatherproof. Locate unit indoors where
ambient air temperature is a minimum of 70°F (21°C).
• This unit is not “jet-proof” construction. Do not use jet-
clean spray to clean this unit.
• Do not steam clean or use excessive water on unit.
• Do not clean unit when it is energized or hot.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
WARNING
This unit has no “user-serviceable” parts. If service is
required on this unit, contact an Authorized Hatco Service
Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350.
NOTE: The internal blower motor is permanently lubricated and
requires no maintenance.
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch finish of unit, marring
its appearance and making it susceptible to soil
accumulation.
Clean unit daily to avoid malfunctions and maintain
sanitary operation.
NOTICE
WARNING
MAINTENANCE
Form No. FSHC67M-0117
12
MAINTENANCE
English
Daily Cleaning
To preserve the finish of the unit as well as maintain
performance, it is recommended that the unit be cleaned daily.
1. Move the POWER ON/OFF (I/O) switch to the OFF (O)
position and unplug the power cord. Allow the unit to cool.
2. Remove and wash all food pans.
3. For humidified units, drain and clean the water reservoir.
Refer to the “Cleaning/Draining the Water Reservoir”
procedure in this section.
4. Wipe down all the interior and the exterior surfaces using
a clean, damp cloth. Stubborn stains may be removed with
a good non-abrasive cleaner. Hard to reach areas should
be cleaned with a small brush and mild soap.
5. Wipe dry with a clean, non-abrasive cloth.
Cleaning/Draining the Water Reservoir
On humidified units, the water reservoir must be drained for
daily cleaning, before moving the cabinet, and during the
“Removing Lime and Mineral Deposits” procedure.
ELECTRIC SHOCK HAZARD: Turn OFF power switch,
unplug power cord, and allow unit to cool before
performing any cleaning, adjustments, or maintenance.
1. Move the POWER ON/OFF (I/O) switch to the OFF (O)
position and unplug the power cord. Allow the unit to cool.
2. Locate the valve inside the cabinet on the underside of the
ceiling sheet. CAUTION: Burn Hazard—Ceiling sheet
and water in reservoir are hot during operation. Allow
to cool before draining.
3. Position a one gallon (four liter) container under the valve.
4. Turn the valve handle from the horizontal position (closed)
to the vertical position (open) to drain the reservoir.
5. Once the reservoir is empty, return the valve handle to the
closed position.
NOTE: If the water used has an excessive amount of lime or
mineral content, follow the “Removing Lime and Mineral
Deposits” procedure for periodic cleaning and deliming
of the water reservoir. Unit failure caused by liming or
sediment buildup is not covered under warranty.
Draining the Water Reservoir
WARNING
Valve
Open
Valve
Closed
Removing Lime and Mineral Deposits
Use the following procedure for periodic cleaning and deliming
of the water reservoir on humidified models.
NOTE: The lime and mineral content of the water used for daily
operation will determine how often the deliming
procedure must be performed.
NOTE: Perform this procedure when the unit will not be used
for a period of time, such as the end of the day.
1. Move the POWER ON/OFF (I/O) switch to the OFF (O)
position and unplug the power cord. Allow the unit to cool.
2. After the unit has cooled down, perform the “Draining the
Water Reservoir” procedure in this section.
3. Fill the water reservoir with a mixture of 75% water and 25%
white vinegar. Do not use flavored vinegar.
4. Plug in and turn on the unit.
5. Set both the temperature and humidity controls to their
highest settings and allow the unit to run for 30 minutes.
6. Move the POWER ON/OFF (I/O) switch to the OFF (O)
position and unplug the power cord. Allow the unit to cool.
7. Perform the “Draining the Water Reservoir” procedure to
empty the deliming solution from the water reservoir.
8. Continue to fill and drain the water reservoir with clean water
until the deliming solution is rinsed through and the reservoir
is clean.
9. Plug the unit into its power source and fill the reservoir as
usual for daily operation. Refer to the procedure in the
OPERATION section of this manual.
Symptom Probable Cause Corrective Action
Unit is plugged in, but nothing
works.
Unit not turned on. Move POWER ON/OFF (I/O) switch to the ON (I) position.
No power to unit. Check electrical receptacle and verify that power supply
matches specifications on unit. If receptacle is not working,
check circuit breaker and reset, or plug unit into a different
known working receptacle.
Tripped circuit breaker. Check circuit breaker and reset, if tripped.
Power cord is damaged. Contact Authorized Service Agent or Hatco for assistance.
Defective POWER ON/OFF (I/O) switch. Contact Authorized Service Agent or Hatco for assistance.
Unit operates, but is not
circulating air inside cabinet.
Blower motor defective. Contact Authorized Service Agent or Hatco for assistance.
Incorrect voltage supplied to blower motor. Contact Authorized Service Agent or Hatco for assistance.
Unit is not producing any “hot
air” inside cabinet.
Incorrect voltage supplied to heating element. Contact Authorized Service Agent or Hatco for assistance.
Blower motor not working. Contact Authorized Service Agent or Hatco for assistance.
Air heating element(s) defective. Contact Authorized Service Agent or Hatco for assistance.
Unit is producing erratic
temperatures inside cabinet.
Air thermostat control is defective. Contact Authorized Service Agent or Hatco for assistance.
Air down tube is not connected/removed. Reconnect/Install air down tube. Contact Authorized Service
Agent or Hatco for assistance.
Unit is heating, but is not
producing humidity inside
cabinet. Low water light is OFF
and unit is full of water.
Water heating element is defective. Contact Authorized Service Agent or Hatco for assistance.
Humidity thermostat control is set too low. Adjust humidity control to higher setting.
Humidity thermostat control defective. Contact Authorized Service Agent or Hatco for assistance.
Unit is heating, but is not
producing humidity inside
cabinet. Low water light is ON,
but unit is full of water.
Water level sensor defective. Contact Authorized Service Agent or Hatco for assistance.
Form No. FSHC67M-0117
13
TROUBLESHOOTING GUIDE
English
This unit must be serviced by trained and qualified
personnel only. Service by unqualified personnel may lead
to electric shock or burn.
WARNING
ELECTRIC SHOCK HAZARD: Turn OFF power switch,
unplug power cord, and allow unit to cool before
performing any cleaning, adjustments, or maintenance.
WARNING
Troubleshooting Questions?
If you continue to have problems resolving an issue, please
contact the nearest Authorized Hatco Service Agency or Hatco
for assistance. To locate the nearest Service Agency, log onto
the Hatco website at www.hatcocorp.com and click on
Find Service Agent, or contact the Hatco Parts and Service
Team at:
Telephone: 800-558-0607 or 414-671-6350
e-mail: part[email protected]
Form No. FSHC67M-0117
14
OPTIONS AND ACCESSORIES
English
Installing Legs
Use the following procedure to install optional 4″ (102 mm) or
6″ (152 mm) legs.
1. Remove the pan shelves and drain the water reservoir, if
necessary.
2. Carefully lay the unit on its back side. This step requires
two people.
NOTE: Place a piece of cardboard between the cabinet and
the floor to prevent marring the cabinet finish.
3. Remove the mounting screws and casters on each corner
of the unit, if installed.
4. Reinstall the mounting screws at each corner directly into
the bottom of the unit. They are not needed for leg
installation.
5. Screw the legs to the bottom of the unit. Tighten securely.
6. Return the unit to its upright position. This step requires
two people.
7. Replace the pan shelves inside the cabinet.
8. Level the unit after it is placed in its final position. The feet
on the legs are adjustable for leveling.
9. Refill the water reservoir.
Stacking Option
A stacking option is available for stacking one unit on top of
another. The stacking option requires the purchase of an
additional unit with a stacking bracket and hardware to secure
the top unit to the bottom unit.
NOTE: Casters are required on stacked units.
1. Make sure the bottom unit is completely assembled with
casters installed. Refer to the appropriate procedure in
either the INSTALLATION section or the OPTIONSAND
ACCESSORIES section.
2. Remove the pan shelves from inside each cabinet and
drain the water reservoirs, if necessary.
3. Carefully lay the top unit on its side (this step requires at
least two people).
NOTE: Place a piece of cardboard between the cabinet and
the floor to prevent marring the cabinet finish.
4. Attach the stacking bracket to the underside of the top unit.
a. Position the bracket so that the flange without screw
holes is toward the front and the flange with two screw
holes is toward the back.
b. Screw four bracket screws on each end of the side
brackets to secure the side brackets to the front and
back bracket.
c. At each corner of the side brackets, screw the bottom
screws through the underside of the bracket and into the
underside of the unit (eight screws total, supplied with
kit). Tighten securely.
5. Remove and discard the two screws in the rear of the top
cover of the bottom unit.
6. Carefully lift and place the top unit onto the bottom unit (this
step requires at least two people). The flanges on the
stacking bracket will fit around the front, sides, and back of
the bottom unit. CAUTION! Do not lift unit by stacking
bracket. Bracket has edges that may cause injury.
7. Align the holes in the back flanges of the stacking bracket
with the holes in the back of the top cover on the bottom
unit.
8. Install the two mounting screws (supplied with kit) through
the holes in the back flanges of the stacking bracket and
into the holes in the back of the top cover on the bottom
unit. Tighten securely.
9. Replace the pan shelves inside each cabinet.
10. Refill the water reservoir.
Stacking two units
Stainless Steel Door (FSHC-6W Series Only)
The optional heavy duty stainless steel door is not available for
retrofit.
Pan Shelves
Additional stainless steel pan shelves are available as
accessories. Use additional pan shelves to increase the pan
capacity of the unit when the height of the pans/product allow.
Front
Bracket
Side
Bracket
Bottom
Screws
Bracket
Screws
Back
Bracket
Mounting
Screw
Form No. FSHC67M-0117
15
LIMITED WARRANTY
English
1. PRODUCT WARRANTY
Hatco warrants the products that it manufactures (the
“Products”) to be free from defects in materials and
workmanship, under normal use and service, for a period of
one (1) year from the date of purchase when installed and
maintained in accordance with Hatco’s written instructions or
18 months from the date of shipment from Hatco. Buyer must
establish the Product’s purchase date by registering the Product
with Hatco or by other means satisfactory to Hatco in its sole
discretion.
Hatco warrants the following Product components to be free
from defects in materials and workmanship from the date of
purchase (subject to the foregoing conditions) for the period(s)
of time and on the conditions listed below:
a) One (1) Year Parts and Labor PLUS One (1) Additional
Year Parts-Only Warranty:
Conveyor Toaster Elements (metal sheathed)
Drawer Warmer Elements (metal sheathed)
Drawer Warmer Drawer Rollers and Slides
Strip Heater Elements (metal sheathed)
Display Warmer Elements (metal sheathed air heating)
Holding Cabinet Elements (metal sheathed air heating)
Heated Well Elements — HW and HWB Series
(metal sheathed)
b) Two (2) Year Parts and Labor Warranty:
Induction Ranges
c) One (1) Year Parts and Labor PLUS Four (4) Years
Parts-Only Warranty:
3CS and FR Tanks
d) One (1) Year Parts and Labor PLUS Nine (9) Years
Parts-Only Warranty on:
Electric Booster Heater Tanks
Gas Booster Heater Tanks
e) Ninety (90) Day Parts-Only Warranty:
Replacement Parts
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN
LIEU OF ANY OTHER WARRANTY, EXPRESSED OR
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE OR PATENT OR OTHER
INTELLECTUAL PROPERTY RIGHT INFRINGEMENT.
Without limiting the generality of the foregoing, SUCH
WARRANTIES DO NOT COVER: Coated incandescent light
bulbs, fluorescent lights, heat lamp bulbs, coated halogen light
bulbs, halogen heat lamp bulbs, xenon light bulbs, LED light
tubes, glass components, and fuses; Product failure in booster
tank, fin tube heat exchanger, or other water heating equipment
caused by liming, sediment buildup, chemical attack, or
freezing; or Product misuse, tampering or misapplication,
improper installation, or application of improper voltage.
2. LIMITATION OF REMEDIES AND DAMAGES
Hatco’s liability and Buyer’s exclusive remedy hereunder will be
limited solely, at Hatco’s option, to repair or replacement using
new or refurbished parts or Product by Hatco or a Hatco-
authorized service agency (other than where Buyer is located
outside of the United States, Canada, United Kingdom, or
Australia, in which case Hatco’s liability and Buyer’s exclusive
remedy hereunder will be limited solely to replacement of part
under warranty) with respect to any claim made within the
applicable warranty period referred to above. Hatco reserves
the right to accept or reject any such claim in whole or in part.
In the context of this Limited Warranty, “refurbished” means a
part or Product that has been returned to its original
specifications by Hatco or a Hatco-authorized service agency.
Hatco will not accept the return of any Product without prior
written approval from Hatco, and all such approved returns shall
be made at Buyer’s sole expense. HATCO WILL NOT BE
LIABLE, UNDER ANY CIRCUMSTANCES, FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES, INCLUDING
BUT NOT LIMITED TO LABOR COSTS OR LOST PROFITS
RESULTING FROM THE USE OF OR INABILITY TO USE THE
PRODUCTS OR FROM THE PRODUCTS BEING
INCORPORATED IN OR BECOMING A COMPONENT OF
ANY OTHER PRODUCT OR GOODS.
16
Formulaire n° FSHC67M-0117
Français
Ce
manuel
f
ourni
t
des
i
nst
ruct
i
ons
concernant
l
'i
nst
al
l
at
i
on,
l
a
s
é
c
u
rité
e
t le
fo
n
c
tio
n
n
e
m
e
n
t d
e
l'
a
rm
o
ire
d
e
c
o
n
s
e
rv
a
tio
n
p
o
rta
b
le
F
l
av-R-S
avor
.
I
l
est
recommandé
de
l
i
re
t
out
es
l
es
i
nst
ruct
i
ons
d'i
nstal
l
ati
on, de s
écuri
té et de f
onct
i
onnem
ent contenues
dans
c
e
manuel avant d'installer et d'utiliser le
Flav-R-Savor
.
Les consignes de sécurité qui apparaissent dans ce manuel
sont identifiées par les mots indicateurs suivants :
AVERTISSEMENT indique une situation dangereuse qui, si
elle n’est pas évitée, peut provoquer la mort ou des
blessures graves.
ATTENTION indique une situation dangereuse qui, si elle
n’est pas évitée, peut provoquer des blessures légères ou
moyennes.
AVIS est utilisé pour des questions sans rapport avec des
blessures corporelles.
AVERTISSEMENT
ATTENTION
AVIS
INTRODUCTION
Les armoires de conservation portables Hatco Flav-R-Savor
®
sont conçues pour conserver des aliments préparés pendant
de longues périodes tout en préservant la qualité d'un « produit
frais ». Elles offrent le meilleur environnement pour les aliments
car elles régulent la température de l'air tout en équilibrant
simultanément le niveau d'humidité. L'utilisation d'une chaleur
humide et contrôlée permet de maintenir la température de
service et de préserver la texture des aliments plus longtemps
qu'avec un équipement traditionnel de conservation des
aliments au sec.
Le schéma de flux d'air Flav-R-Savor est conçu pour maintenir
une température constante dans l'armoire sans assécher les
aliments. L'association précise de la chaleur et l'humidité crée
un effet « couverture » autour de l'aliment. Le débit d'air permet
à la vitrine de retrouver rapidement sa température initiale
après ouverture et fermeture de la porte.
Les armoires de conservation portables Flav-R-Savor ont fait
l'objet de nombreuses recherches et de tests sur le terrain. Les
matériaux utilisés ont été sélectionnés pour une durabilité
maximale, un aspect esthétique et une performance optimale.
Chaque appareil est soigneusement inspecté et testé avant
expédition.
Informations Importantes pour le Propriétaire ................16
Introduction.........................................................................16
Consignes de Sécurité Importantes .................................17
Description du Modèle .......................................................18
Désignation du Modèle ......................................................18
Caractéristiques Techniques.............................................19
Configuration des fiches ....................................................19
Tableau des valeurs nominales électriques.......................19
Dimensions ........................................................................21
Installation ...........................................................................22
Généralités.........................................................................22
Inversion de la porte d'accès.............................................23
Mode d'emploi.....................................................................24
Généralités.........................................................................24
Guide de conservation des aliments .................................25
Maintenance ........................................................................25
Généralités.........................................................................25
Nettoyage quotidien...........................................................26
Nettoyage/Vidange du réservoir d'eau ..............................26
Retrait des dépôts de chaux et de minéraux.....................26
Guide de Dépannage..........................................................27
Options et Accessoires......................................................28
Garantie Limitée..................................................................29
Autorisés Distributeurs de Pièces ........Couverture Arrière
INFORMATIONS IMPORTANTES POUR LE PROPRIÉTAIRE
Noter le numéro de modèle, le numéro de série (étiquette de
spécification située à l'arrière de l'appareil), le voltage et la date
d’achat de votre appareil ci-dessous. Veuillez avoir cette
information à portée de la main si vous appelez Hatco pour
assistance.
Modèle No.____________________________________
Numéro de série________________________________
Voltage ______________________________________
Date d’achat __________________________________
Enregistrez votre appareil!
Remplissez la garantie en ligne pour éviter les retards pour
faire jouer la garantie. Accédez au site Web Hatco
www.hatcocorp.com, sélectionnez le menu déroulant Parts
& Service, puis cliquez sur Warranty Registration.
Horaires
ouvrables : 7h00 à 17h00
Heure du Centre des États-Unis (CST)
(Horaires d’été : juin à septembre—
7h00 à 17h00 CST du lundi au jeudi
7h00 à 16h00 CST le vendredi)
Téléphone : 800-558-0607; 414-671-6350
Courriel : partsandservice@hatcocorp.com
Des renseignements supplémentaires sont disponibles sur
notre site Web à www.hatcocorp.com.
Service d'assistance et de pièces de
rechange disponible 7j/7, 24h/24 aux
États-Unis et au Canada en composant
le 800-558-0607.
SOMMAIRE
Formulaire n° FSHC67M-0117
17
CONSIGNES DE SÉCURITÉ IMPORTANTES
Français
Hatco Corporation n'est pas responsable de la température
réelle à laquelle les aliments sont servis. Il est de la
responsabilité de l'utilisateur de s'assurer que les produits
alimentaires sont maintenus et servis à une température
sans danger.
Assurez-vous que tous les opérateurs ont été formés à
l'utilisation sûre et correcte de l'appareil.
Cet appareil ne doit pas être utilisé par des enfants ou des
personnes avec des capacités physiques, sensorielles ou
mentales diminuées. Assurez-vous que les enfants sont
bien surveillés et tenez-les à l'écart de l'appareil.
Cet appareil ne contient aucune pièce réparable par
l’utilisateur. Si cet appareil doit être réparé, contacter un
réparateur Hatco agréé ou le Service après-vente Hatco au
+1 800-558-0607 ou +1 414-671-6350.
DANGER DE BRÛLURE:
•
Certaines surfaces extérieures de l’appareil deviennent
chaudes. Toucher ces zones de l’appareil avec précaution.
• Éteindre l'appareil et le laisser refroidir avant de
vidanger l'eau se trouvant dans le réservoir d'eau.
Placer l’appareil sur un plan de travail de hauteur correcte
à un endroit qui convient pour son utilisation. Le support
doit être de niveau pour éviter toute chute accidentelle du
grille-pain ou de son contenu et suffisamment solide pour
résister au poids de l’appareil et de son contenu.
Ne pas trop remplir le réservoir d'eau. Si le réservoir est
trop rempli, de l'eau risque de s'écouler sur le sol et
d'entraîner un risque de glissement.
L'unité doit rester droite durant son transport. S'assurer
que toute l'eau a bien été vidangée avant le transport.
Ne pas poser l'appareil sur le côté comportant le panneau
de commande car cela risquerait de l'endommager. Veiller
à ce que toute l'eau soit vidangée avant de poser l'appareil
sur le côté.
Utilisez seulement des nettoyants non abrasifs et des
chiffons doux. Les chiffons et nettoyant abrasifs pourraient
érafler la finition de l'unité, entachant son apparence et la
rendant susceptible à l'accumulation de saleté.
Il est recommandé d'utiliser de l'eau distillée dans le
réservoir d'eau des appareils humidifiés. Si de l'eau non
distillée est utilisée, il est nécessaire de nettoyer et de
détartrer régulièrement le réservoir (se reporter à la section
Maintenance pour obtenir des informations sur la
procédure de nettoyage).
N'utilisez pas de l'eau déionisée ou de l'eau purifiée par
osmose inverse. Cela raccourcirait la durée de vie du
réservoir d'eau et des éléments chauffants.
Nettoyez l'unité quotidiennement pour éviter les
dysfonctionnements et assurer un fonctionnement sain.
ATTENTION
AVIS
AVERTISSEMENT
DANGER DE DÉCHARGE ÉLECTRIQUE:
• Brancher l’appareil sur une prise de courant avec terre de
tension, de format et de configuration des broches corrects.
Si la fiche et la prise ne se correspondent pas, s’adresser à
un électricien qualifié pour déterminer et installer une prise
de courant de format et de tension corrects.
• Mettez l'unité hors tension depuis l'interrupteur,
débranchez le cordon d'alimentation et laissez l'unité
refroidir avant d'effectuer tout nettoyage, tout réglage
ou tout entretien.
• NE PAS immerger l’appareil ni le saturer d’eau.
L’appareil n’est pas étanche à l’eau. Ne pas le faire
fonctionner s’il a été immergé ou saturé d’eau.
• L’appareil n’est pas à l’épreuve des intempéries. Placer
l’appareil à l’intérieur à une température ambiante de
21°C (70°F) minimum.
• Cet appareil n’est pas étanche aux jets. Ne pas utiliser
de jet sous pression pour nettoyer l’appareil.
• Ne pas nettoyer à la vapeur ni utiliser trop d’eau sur
l’appareil.
• Mettre le contacteur d'alimentation en position OFF et
laisser l'appareil se refroidir avant de vidanger le
réservoir d'eau.
• Ne pas tirer l’appareil par son cordon électrique.
• Ne pas utiliser l’appareil si le cordon est endommagé
ou usé.
• Ne pas tenter de réparer ni de changer un cordon
électrique endommagé. Ce cordon doit être changé par
Hatco, par un réparateur Hatco agréé ou par une
personnes de qualifications comparables.
• La réparation de cet appareil doit être confiée
exclusivement à du personnel qualifié. Les réparations
par des personnes non qualifiées peuvent provoquer
des décharges électriques et des brûlures.
• Utilisez uniquement des pièces de rechange d'origine
Hatco lorsque l'entretien est nécessaire. Utilisez des
pièces détachées Hatco authentiques sous peine
d'annuler toutes les garanties et d'exposer l’utilisateur
à des tensions électriques dangereuses pouvant
entraîner une électrocution ou des brûlures. Les pièces
de rechange authentiques Hatco sont spécifiées pour
fonctionner en toute sécurité dans les environnements
dans lesquels elles sont utilisées. Certaines pièces de
rechange génériques ou d'après-vente n'ont pas les
caractéristiques qui leur permettent d'opérer en toute
sécurité dans les équipements Hatco.
DANGER D’INCENDIE : Placer l’appareil à un minimum de
25 mm (1″) des parois et matières combustibles. Si une
distance sûre n’est pas maintenue, la chaleur peut
provoquer une combustion ou une altération de couleur.
Assurez-vous que la nourriture a été chauffée à une
température adaptée à une alimentation saine avant de la
placer dans l'appareil. Le non-chauffage des aliments à une
température appropriée peut poser un grand risque pour la
santé. Cet appareil n'est destiné qu'à maintenir des
aliments préchauffés au chaud.
AVERTISSEMENT
Lisez l'information de securite importante suivante avant d'utiliser cet équipement pour éviter
des dommages ou la mort sérieux et pour éviter d'endommager l'équipement ou la propriété.
18
Formulaire n° FSHC67M-0117
DESCRIPTION DU MODÈLE
Français
Tous les Modèles
L'armoire de conservation portable Flav-R-Savor
®
est fabriquée
en acier inoxydable solide et les surfaces supérieures, latérales
et arrière sont peintes par poudrage. Elle est équipée d'un
système de chaleur contrôlée par thermostat, d'un système d'air
de convexion à vitesse lente, d'un système d'humidité et d'une
grande porte en verre trempé encadrée d'aluminium (une porte
en acier isolée et résistante est également disponible pour le
modèle FSHC-6W1). Les charnières de la porte d'accès
peuvent être fixées à gauche ou à droite, selon la demande.
Les commandes sont facilement accessibles et comprennent
un interrupteur ON/OFF (Marche/Arrêt) et un affichage de
température digital. Cet appareil peut être transporté grâce à
des roulettes de 102 mm (4″), les deux roulettes avant étant
des roulettes pivotantes équipées de systèmes de verrouillage.
Les appareils sont gris argent de série mais sont également
disponibles en option acier inoxydable ou noir et peuvent être
configurés sans système d'humidité. Un câble d'alimentation
de 1829 mm (6″) et une prise sont fournis de série.
Une option d'empilement est disponible pour pouvoir placer un
appareil sur un autre. Se reporter à la rubrique OPTIONS ET
ACCESSOIRES pour obtenir plus d'informations sur toutes les
options disponibles.
Modèle FSHC-6W1
Le FSHC-6W1 est un modèle à porte unique conçu pour tenir
sous les plans de travail bas. L'armoire est équipée de 6 paires
de glissières d'angle. Ces glissières sont conçues pour soutenir
des plaques de grande taille, différentes tailles de marmites de
chauffage au bain-marie (grande, moyenne et petite) et des
bacs Gastronorm.
Un modèle sans système d'humidification est également
disponible. Les appareils sans système d'humidification sont
équipés d'une porte en acier inoxydable ajourée et résistante et
d'un grill à 4 étages. Le modèle sans système d'humidification
est conçu pour le montage sur comptoir uniquement et est livré
sans roulettes ni pieds.
Modèle FSHC-6W2
Le modèle FSHC-6W2 possède toutes les fonctionnalités du
FSHC-6W1 avec 2 portes en plus pour le passage des plats.
Modèle FSHC-6W1
Modèle FSHC-7-1
Le FSHC-7-1 est un modèle à porte unique. L'armoire est
équipée de 7 paires de glissières d'angle. Ces glissières sont
conçues pour soutenir des plaques de grande taille, différentes
tailles de marmites de chauffage au bain-marie (grande,
moyenne et petite) et des bacs Gastronorm.
Modèle FSHC-7-2
Le modèle FSHC-7-2 possède toutes les fonctionnalités du
FSHC-7-1 avec 2 portes en plus pour le passage des plats.
Modèle FSHC-7-1
DÉSIGNATION DU MODÈLE
F S H C - X W - X
Flav-R-Savor
Armoire de conservation
Capacité des plateaux de grande taille
W = Capacité d'une grande armoire
Pas de lettre = Largeur standard
Nombre de portes
Modèle Tension Intensité
Amps Hertz
Configuration de
Fiches
FSHC-6W1 et
FSHC-6W2
(Humidifié)
120 1697 14.1 60 NEMA 5-15P*
220 1697 7.7 50
CEE 7/7 Schuko
240 1697 7.1 50
BS-1363, AS 3112
220–230 (CE) 1697–1850 7.7–8.0 50
CEE 7/7 Schuko
230–240 (CE) 1562–1697 6.8–7.1 50
BS-1363
FSHC-6W1 et
FSHC-6W2
(Non humidifié)
120 1097 9.2 60 NEMA 5-15P
FSHC-7-1 et
FSHC-7-2
(Humidifié)
120 1697 14.1 60 NEMA 5-15P*
220 1697 7.7 50
CEE 7/7 Schuko
240 1697 7.1 50
BS-1363, AS 3112
220–230 (CE) 1697–1850 7.7–8.0 50
CEE 7/7 Schuko
230–240 (CE) 1562–1697 6.8–7.1 50
BS-1363
FSHC-7-1 et
FSHC-7-2
(Non humidifié)
120 1097 9.2 60 NEMA 5-15P
220 1093 5 50
CEE 7/7 Schuko
240 1101 4.6 50
BS-1363, AS 3112
220–230 (CE) 1093–1195 5.0–5.2 50
CEE 7/7 Schuko
230–240 (CE) 1011–1097 4.4–4.6 50
BS-1363
Formulaire n° FSHC67M-0117
19
CARACTÉRISTIQUES TECHNIQUES
Français
Configuration des fiches
Les appareils sont livrés avec un cordon électrique avec fiche.
DANGER DE DÉCHARGE ÉLECTRIQUE : Brancher
l’appareil sur une prise de courant avec terre de tension, de
format et de configuration des broches corrects. Si la fiche
et la prise ne se correspondent pas, s’adresser à un
électricien qualifié pour déterminer et installer une prise de
courant de format et de tension corrects.
NOTA: L'étiquette des caractéristiques techniques est située à
l'arrière de l'appareil. Reportez-vous à l'étiquette du
numéro de série et les données électriques de l'appareil.
AVERTISSEMENT
Configuration des fiches
NOTA: Prise non fournie par Hatco.
NEMA 5-15P
CEE 7/7 Schuko AS 3112
BS-1363
NEMA 5-20P
Tableau des valeurs nominales électriques — Norme Wattage
Les zones ombrées contiennent des informations électriques pour les modèles internationaux uniquement.
* NEMA 5-20P pour Canada.
Poids d’embarquement
FSHC-6W1: 84 kg (185 lbs.)
FSHC-6W2: 86 kg (190 lbs.)
FSHC-7-1: 79 kg (175 lbs.)
FSHC-7-2: 82 kg (180 lbs.)
Modèle Tension Intensité
Amps Hertz
Configuration de
Fiches
FSHC-6W1 et
FSHC-6W2
(Humidifié)
220 2047 9.3 50
CEE 7/7 Schuko
240 2047 8.5 50
BS-1363, AS 3112
220–230 (CE) 2047–2233 9.3–9.7 50
CEE 7/7 Schuko
230–240 (CE) 1884–2047 8.2–8.5 50
BS-1363
FSHC-6W1 et
FSHC-6W2
(Non humidifié)
120 1440 12 60 NEMA 5-15P*
FSHC-7-1 et
FSHC-7-2
(Humidifié)
220 2047 9.3 50
CEE 7/7 Schuko
240 2047 8.5 50
BS-1363, AS 3112
220–230 (CE) 2047–2233 9.3–9.7 50
CEE 7/7 Schuko
230–240 (CE) 1884–2047 8.2–8.5 50
BS-1363
FSHC-7-1 et
FSHC-7-2
(Non humidifié)
120 1440 12 60 NEMA 5-15P*
220 1447 6.6 50
CEE 7/7 Schuko
240 1447 6 50
BS-1363, AS 3112
220–230 (CE) 1447–1581 6.6–6.9 50
CEE 7/7 Schuko
230–240 (CE) 1328–1447 5.8–6 50
BS-1363
20
Formulaire n° FSHC67M-0117
CARACTÉRISTIQUES TECHNIQUES
Français
Tableau des valeurs nominales électriques — Haute Puissance
Les zones ombrées contiennent des informations électriques pour les modèles internationaux uniquement.
* NEMA 5-20P pour Canada.
Poids d’embarquement
FSHC-6W1: 84 kg (185 lbs.)
FSHC-6W2: 86 kg (190 lbs.)
FSHC-7-1: 79 kg (175 lbs.)
FSHC-7-2: 82 kg (180 lbs.)
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
Hatco FSHC-6W, FSHC-7 Series Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
dans d''autres langues
Documents connexes
-
Hatco FSHC-5W-EE, FSHC-7W-EE Series Le manuel du propriétaire
-
-
Hatco GRCD and GRHD Series Glo-Ray Heated Display Cases Le manuel du propriétaire
-
-
-
-
-
-
-
Hatco FSD, FSDT Series Le manuel du propriétaire