Nexgrill 720-0830D Le manuel du propriétaire

Questions, problems, missing parts? Before returning to your retailer, call our customer service

department at Canada: 800-648-5864, U.S.: 800-913-8999, 8 a.m.-5 p.m., PST, Monday-Friday.

OUTDOOR GAS GRILL

• This instructions manual contains important information necessary for the proper

assembly and safe use of the appliance.

• Read and follow all warnings and instructions before assembling and using the

appliance.

• Keep this manual for future reference.

SERIAL # ____________________ MFG. DATE _____________ PURCHASE DATE: ____________

MODEL #720/730-0830D Pages 2 - 43

19000445A0

GRIL À GAS EXTÉRIEUR

MODÈLE 720/730-0830D Pages 44-86

Table of Contents

Lighting Instruction. . . . . . . . . . . . . . . . . . . .

Care and Maintenance . . . . . . . . . . . . . . . . .

Trouble Shooting . . . . . . . . . . . . . . . . . . . . .

Ordering Parts . . . . . . . . . . . . . . . . . . . . . . . .

Grill Hints . . . . . . . . . . . . . . . . . . . . . . . . . . .

Grill Cooking Chart . . . . . . . . . . . . . . . . . .. .

Grill Recipe Suggestion . . . . . . . . . . . . . . .

Limited Warranty . . . . . . . . . . . . . . . . . . . . .

Natural Gas Conversion …………………

26-27

28

29-30

31

31-32

33-34

35

36-43

Safety Instruction . . . . . . . . . . . . . . . . . . . . .

Package Contents List . . . . . . . . . . . . . . . . .

Hardware Contents . . . . . . . . . . . . . . . . . . . .

Exploded View . . . . . . . . . . . . . . . . . . . . . . . .

Part List . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Assembly Instruction . . . . . . . . . . . . . . . . . .

Motor Instruction . . . . . . . . . . . . . . . . . . . . . .

Gas Hook –Up . . . . . . . . . . . . . . . . . . . . . . .

Installer Final Check List. . . . . . . . . . . . . . . .

Leak Testing . . . . . . . . . . . . . . . . . . . . . . . .

Operating Instruction . . . . . . . . . . . . . . . . . . .

Grill Lighting Instruction . . . . . . . . . . . . . . . .

3-6

7-8

9

10

11-12

13-20

21

22

23

23-24

25

25-26

2

1. Never operate this appliance unattended.

2. Never operate this appliance within 10 ft (3 m) of any structure, combustible

material or other gas cylinder.

3. Never operate this appliance within 25 ft (7.5 m) of any flammable liquid.

4. Do not fill cooking vessel beyond maximum fill line.

5. Heated liquids remain at scalding temperatures long after the cooking process.

Never touch cooking appliance until liquids have cooled to 115ºF (45ºC) or less.

6. This appliance is not intended for and should never be used as a heater.

7. If a fire should occur, keep away from the appliance and immediately call your fire

department. Do not attempt to extinguish an oil or grease fire with water.

DANGER

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. Open lid.

4. If odor continues, keep away from the

appliance and immediately call your

gas supplier or your fire department.

WARNING

1. Do not store or use gasoline or

other flammable liquids or vapors in

the vicinity of this or any other

appliance.

2. An LP cylinder not connected for

use shall not be stored in the

vicinity of this or any other

appliance.

Failure to comply with these instructions could result in a fire or explosion that

could cause serious bodily injury, death, or property damage.

Combustion by products produced when using this product contain chemicals

known to the States of California to cause cancer, birth defects, or other reproductive

harm.

Your grill will be very hot. Never lean over the cooking area while using your grill.

Do not touch cooking surfaces, grill housing, lid or any other grill parts while the grill

is in operation, or until the gas grill has cooled down after use.

DANGER

Safety Instruction

3

WARNING

ELECTRICAL GROUNDING INSTRUCTIONS for Rotisserie Motor-This appliance is equipped with a plug and should be

plugged directly into a properly grounded receptacle. When installed, must be electrically grounded in accordance with local

codes or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 or the Canadian Electrical Code,

CSA C22.1 DO NOT cut or remove the grounding prong from this plug.

1. To protect against electric shock, do not immerse cord or plugs in water or other liquid.

2. Unplug from the outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts.

3. Do not operate any outdoor cooking gas appliance with a damaged cord, plug, or after the appliance malfunctions or

has been damaged in any manner. Contact the manufacturer for repair.

4. Do not let the cord hang over the edge of a table of touch hot surface.

5. Do not use an outdoor cooking gas appliance for purposes other than intended.

6. When connecting, first connect plug to the outdoor cooking gas appliance then plug appliance into the outlet.

7. Use only a Ground Fault Interrupt (GFI) protected circuit with this outdoor cooking gas appliance.

8. Never remove the grounding plug or use with an adapter of 2 prongs.

9. Use only extension cords with a 3 prong grounding plug, rated for the power of the equipments, and approved for

outdoor use with a W-A marking.

Safety Instruction

WARNING

Do not try lighting this appliance without reading the

“LIGHTING INSTRUCTIONS” section of this manual.

CAUTION: Beware of Flashback

TESTED IN ACCORDANCE WITH ANS Z21.58b CSA

1.6b-2012 STANDARD FOR OUTDOOR COOKING GAS

APPLIANCE. THIS GRILL IS FOR OUTDOOR USE ONLY.

CAUTION: Spiders and small insects occasionally

spin webs or make nest in the grill

burner tubes during transit and

warehousing. These webs can lead

to gas flow obstruction, which could

result in a fire in and around burner

tubes. This type of fire is known as

“FLASH-BACK” and can cause serious damage to your grill

and create an unsafe operating condition for the user.

Although an obstructed burner tube is not the only cause of

“FLASH-BACK”, it is the most common cause.

To reduce the chance of “FLASH-BACK”, you must clean the

burner tubes before assembling your grill, and at least once a

month in late summer or early fall when spiders are most

active. Also perform this burner tube cleaning procedure if

your grill has not been used for an extended period of time. A

clogged tube can be lead to a fire beneath the grill.

Grill Installation Codes

Check your local building codes for the proper method of

installation. in the absence of local codes, this unit should

be installed in accordance with the National Fuel Gas

Code ,ANSI Z223.1/NFPA 54,Storage and Handling of

Liquefied Petroleum Gases, ANSI /NFPA B149.2 or CSA

B149.1 Natural Gas and Propane Installation Code, and

the National Electrical Code, ANSI/NFPA 70.

Correct LP Gas Tank Use

LP gas grill models are designed for use with a standard 20

lb. Liquid Propane Gas tank, not included with grill. Never

connect your gas grill to an LP gas tank that exceeds this

capacity.

If an external electrical source is utilized: The outdoor

cooking gas appliance, when installed, must be electrically

grounded in accordance with local codes or, in the absence

of local codes, with the National Electrical Code,

ANSI/NFPA 70, or the Canadian Electrical Code, CSA

C22.1.

WARNING

Keep any electrical supply cord and the fuel supply hose

away from any heated surfaces.

NOTE: The normal flow of gas through the regulator and

hose assembly can create a humming noise. A low volume

of noise is perfectly normal and will not interfere with

operation of the grill. If humming noise is loud and

excessive you may need to purge air from the gas line or

reset the regulator excess gas flow device. This purging

procedure should be done every time a new LP gas tank is

connected to your grill.

Visually check the burner flames prior to each use. The

flames should look like this picture. If they do not, refer to the

burner main tenancy part of this manual.

4

Safety Instruction

continued

LP-Gas Supply System

• If the information is not followed exactly, a fire resulting in

death or serious injury could occur.

• A 20lb tank of approximately 12-1/4 inches in diameter by 18-

1/4 inches high is the maximum size LP gas tank to use.

• The safety feature prevents the tank from being overfilled,

which can cause malfunction of the LP gas tank, regulator

and/or grill.

• The LP gas supply cylinder to be used must be constructed

and marked in accordance with the specifications for LP –

Gas cylinder of the U.S. Department of Transportation (DOT)

or the National Standard of Canada ,CAN/CSA –B339,

Cylinders, Spheres and Tubes for Transportation of

Dangerous Goods and Commission .

• The LP gas tank must have a shutoff valve terminating in an

LP valve outlet that is compatible with a Type 1. LP gas

supply cylinder must have a shut off valve terminating in a

valve outlet specified for connection type QCC1 in the

standard for compressed gas cylinder valve outlet and inlet

connection ANSI/CGA-V-1 as applicable. LP gas supply

cylinder must be fitted with an Overfill Protection Device

(O.P.D) The LP gas tank must also have a safety relief

device that has a direct connection with the vapor space of

the tank.

• The tank supply system must be arranged for vapor

withdrawal.

• The LP gas tank used must have a collar to protect the tank

valve.

• Place dust cap on cylinder valve outlet whenever the cylinder

is not in use. Only install the type of dust cap on the cylinder

valve outlet that is provided with the cylinder valve. Other

types of cap or plugs may result in leakage of propane.

• Never connect an unregulated LP gas tank to your gas grill.

• This outdoor cooking gas appliance is equipped with a high

capacity hose/regulator assembly for connection to a

standard 20lb. Liquid propane cylinder.

• Have your LP gas tank filled by a reputable propane gas

dealer and visually inspected and re-qualified at each filling.

• Do not store a spare LP gas cylinder under or near this

appliance.

• Never fill the cylinder beyond 80 percent full.

• Always keep LP gas tanks in an upright position.

• Do not store or use gasoline or other flammable vapors and

liquids in the vicinity of this or any other appliance.

• Storage of an outdoor cooking gas appliance indoors is

permissible only if the cylinder is disconnected and removed

from the outdoor cooking gas appliance.

• When your gas grill is not in use the gas must be turned off at

LP gas tank.

• The gas must be turned off at the supply cylinder when the

outdoor cooking gas appliance is not in use.

• LP gas tank must be stored outdoors in a well-ventilated area

and out of reach of children. Disconnected LP gas tanks must

not be stored in a building, garage or any other enclosed area.

• Do Not obstruct the flow of ventilation air around the gas grill

housing. Only use the regulator and the hose assembly

supplied with your gas grill. Replacement regulators and hose

assemblies must be those specified in this manual.

• The regulator and hose assembly must be inspected before

each use of the grill. If there is excessive abrasion or wear or

if the hose is cut, it must be replaced prior to the grill being put

into operation. The replacement hose assembly shall be that

specified by the manufacturer.

• Pressure regulator and hose assembly supplied with the

outdoor cooking gas appliance must be used. Never

substitute other types of regulator. Contact customer service

for manufacturer specified replacement parts.

• This outdoor cooking gas appliance is equipped with a

pressure regulator comply with the standard for Pressure

Regulating Valves for LP Gas ANSI/ UL 144.

• Do not use briquettes of any kind in the grill.

• The grill is designed for optimum performance without the use

of briquettes. Do not place briquettes on the radiant as this will

block off the area for the grill burners to vent. Adding

briquettes can damage ignition components and knobs, and

void the warranty.

• Keep the back and side cart free and clear from debris. Keep

any electrical supply cord, or the rotisserie motor cord away

from the heated areas of the grill.

• Never use the grill in extremely windy conditions. If located in

a consistently windy area (oceanfront, mountaintop, etc.) a

windbreak will be required. Always adhere to the specified

clearance.

• Never use a dented or rusty propane tank.

• Keep any electrical supply cord and the fuel supply hose away

from any heated surface.

• While lighting, keep your face and hands as far away from the

grill as possible.

• Burner adjustment should only be performed after the burner

has cooled.

WARNING

Your grill will get very hot. Never lean over the cooking area

while using your grill. Do not touch cooking surfaces, grill

housing, lid or any other grill parts while the grill is in

operation, or until the gas grill has cooled down after use.

Failure to comply with these instructions may result in

serious bodily injury.

CAUTION: TO ENSURE CONTINUED PROTECTION

AGAINST RISK OF ELECTRIC SHOCK, CONNECT TO

PROPERLY GROUNDED OUTLETS ONLY, TO REDUCE

THE RISK OF ELECTRIC SHOCK, KEEP EXTENSION

CORD CONNECTION DRY AND OFF THE GROUND.

PROPER PLACEMENT AND CLEARANCE OF GRILL

• Never use your gas grill in a garage, porch, shed,

breezeway or any other enclosed area. Your gas grill is

to be used outdoors only.

Do Not install this unit into combustible enclosures.

Minimum clearance from sides and back of unit to

combustible construction, 24 inches (61cm) from sides

and 24 inches (61cm) from back.

• DO NOT use this appliance under overhead combustible

surfaces. This outdoors cooking gas appliance is not

intend to be installed in or on recreational vehicles and/or

boats.

5

Safety Instruction

continued

INSECT WARNING

Spiders and insects can nest in the burners of this and any

other grill, and cause the gas to flow improperly. This is a

very dangerous condition, which can cause a fire to occur

behind and beneath the valve panel, thereby damaging the

grill and making it unsafe to operate. Inspect the grill at least

twice a year.

WARNING

Keep a spray bottle of soapy water near the gas supply

valve and check the connections before each use.

DO NOT USE ALUMINUM FOIL TO LINE THE GRILL

RACKS OR GRILL BOTTOM.

This can severely upset combustion airflow or trap excessive

heat in the control area.

DO NOT LEAVE THE GRILL UNATTENDED WHILE

COOKING.

SAFETY PRACTICES TO AVOID PERSONAL INJURY

When properly cared for your grill will provide safe, reliable

service for many years. However, extreme care must be

used as the grill produces intense heat that can increase

accident potential. When using this appliance basic safety

practices must be followed, including the following:

Do not repair or replace any part of the grill unless

specifically recommended in this manual. All other service

should be referred to a qualified technician.

This grill is not intended to be installed in or on recreational

vehicles or boats.

Children should not be left alone or unattended in an area

where the grill is being used. Do not allow them to sit, stand

or play in or around the grill at any time.

Do not store items of interest to children around or below the

grill.

Do not permit clothing, pot holders or other flammable

materials to come in contact with or too close to any grate,

burner or hot surface until it has cooled. The fabric could

ignite and cause personal injury.

For personal safety, wear proper apparel. Loose fitting

garments or sleeves should never be worn while using this

appliance. Some synthetic fabrics are highly flammable and

should not be worn while cooking.

Only certain types of glass, heat-proof glass ceramic,

earthenware, or other glazed utensils are suitable for grill use.

These materials may break with sudden temperature

changes. Use only on low or medium heat settings in

accordance with the manufacturer’s guidelines.

Do not heat unopened food containers. A build-up of

pressure may cause the containers to burst.

Use a covered hand when opening the grill lid.

Never lean over an open grill.

When lighting a burner, pay close attention to what you are

doing. Make certain you are aware of which burner you are

lighting, so your body and clothing remain clear of open

flames.

When using the grill, do not touch the grill rack, burner

grate or immediate surroundings as these areas become

extremely hot and could cause burns. Use only dry

potholders. Moist or damp potholders on hot surfaces may

cause steam burns. Do not use a towel or bulky cloth in

place or potholders. Do not allow potholders to touch hot

portions of the grill rack.

Grease is flammable. Let hot grease cool before attempting

to handle it. Do not allow grease deposits to collect in the

grease tray at the bottom of the grill’s firebox. Clean the

grease tray often

Do not use aluminum foil to line the grill racks or grill

bottom. This can severely upset combustion air flow or trap

excessive heat in the control area.

For proper lighting and performance of the burners keep

the burner ports clean. It is necessary to clean them

periodically for optimum performance. The burners will only

operate in one position and must be mounted correctly for

safe operation.

Clean the grill with caution. To avoid steam burns, do not

use a wet sponge or cloth to clean the grill while it is hot.

Some cleaners produce toxic fumes or can ignite if applied

to a hot surface.

Turn off grill controls and make certain the grill is cool

before using any type of aerosol cleaner on or around the

grill. The chemical that produces the spraying action could,

in the presence of heat, ignite or cause metal parts to

corrode.

Do not use the grill to cook excessively fatty meats or other

products which promote flare – ups.

Do not operate the grill under unprotected combustible

constructions. Use only in well ventilated areas. Do not use

in buildings, garages, sheds, breezeways or other such

enclosed areas.

Keep the area surrounding the grill free from combustible

materials including, fluids, trash, and vapors such as

gasoline or charcoal lighter fluid. Do not obstruct the flow of

combustion and ventilation air.

WARNING

This outdoor cooking gas appliance is not intended

to be installed in or on boats. And other recreational

vehicles.

6

Package Contents List

A. Firebox assembly-1pc

B. Left side shelf -1pc

C. Right side shelf -1pc

D. Grease pan -1pc

E. Grease cup-1pc F. Back panel, middle-1pc

G. Back panel, bottom-1pc H. Right side panel -1pc I. Left side panel -1pc

J. Cart frame-1pc

K. Diagonal bar barrier -1pc

L. Bottom panel -1pc

M. Tank bolt -1pc N. Right Triangle bracket -1pc O. Left Triangle bracket -1pc

7

Package Contents List

P. Swivel caster -1pc Q. Swivel caster with brake -1pc R. Stationary caster -2pcs

S. Right door -1pc

T. Left door -1pc U. Door handle assembly -2pcs

V. Warming rack -1pc

W. Cooking grid with hole -2pcs

X. Flame tamer -4pcs

Y. Battery -1pc

Z. Grease cup bracket-2 pcs

8

Hardware Contents

Item Description Required for assembly Extra hardware Total

1/4'' x 15mm Truss Head Screw with

locking washer

5/32'' x 10mm Truss Head Screw with

locking washer

5/32'' x 10mm Flat Head Screw

5/32'' Flat Washer

1/4'' Flat Washer

EE 16 pcs 1pc 17 pcs

DD 4 pcs 4pcs

13pcs1pc

0pc

2pcs

CC 12 pcs

49pcs

BB

AA 47 pcs

18 pcs 20pcs

2pcs

9

65

69

71

70

71e

08

09

10

64

01

02

04

05

06

02

59

25

71a

03

71f

71d

71c

71b

56

24

67

68

66

07

11

12

13

14

15

16

17

18

19

20

21

22

23

26

27

31

29

28

30

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51

52

53

54

55

57

58

60

61

62

63

23

Explode View

10

No

.

Part (Description)

Warranty

coverage

(year)

QT

Y

No

.

Part (Description)

Warranty

coverage

(year)

QTY

1 Main lid 1 1 29

Main manifold 1 1

2 Main lid screw 1 2 30 Regulator, LP 1 1

3 Burner pin assembly 1 4 31

Pulse igniter module 1 1

4

Temperature gauge 1 1 32 Main control panel 1 1

5

Temperature gauge

Housing

1133Bezel A 1 4

6 Logo 1 1 34

Bezel B (Small) 1 1

7 Rotisserie motor bracket 1 1 35

Control knob A 1 4

8 Main lid handle seat, left 1 1 36

Control Knob B (Small) 1 1

9 Main lid handle tube 1 1 37 Grease pan 1 1

10 Main lid handle seat, right 1 1 38 Grease cup 1 1

11 Flame tamer 1 4 39 Warming rack 1 1

12 Main burner 5 4 40 Cooking grid with hole 1 2

13 Main burner igniter wire A

1

1 41 Back panel, top 1 1

14 Main burner igniter wire B

1

1 42 Side shelf, left 1 1

15 Main burner igniter wire C

1

1 43 Side shelf front panel, left 1 1

16 Main burner igniter wire D

1

1 44 Back panel, middle 1 1

17 Rotisserie heat shield 1 1 45 Back panel, bottom 1 1

18 Rear baffle 1 1 46 Side panel, left 1 1

19 Rotisserie igniter wire 1 1 47 Swivel caster with Brake 1 1

20 Rotisserie Burner 1 1 48 Swivel caster 1 1

21

Rotisserie burner orifice w/

brass elbow

1 1 49 Bottom panel 1 1

22

Rotisserie burner flex gas

line

1 1 50 Cart frame 1 1

23

Rotisserie burner igniter

bracket

1 2 51 Door magnet 1 2

24 Hood buffer

1

2 52 Triangle Bracket, left 1 1

25

Main burner bowl

assembly

Non-

replaceable

1 53 Triangle Bracket, right 1 1

26 Front baffle 1 1 54 Door iron piece 1 1

27 Main gas valve 1 4 55 Diagonal bar barrier 1 1

28 Rotisserie gas valve 1 1 56 Tank bolt 1 1

11

12

Part List

sold

separately

with #71

Sold

separately

as set

No

.

Part (Description)

Warranty

coverage

(year)

Q

T

Y

No. Part (Description)

Warranty

coverage

(year)

QTY

57

Caster

1 2 70 NG orifice pack 1 1

58

Side panel, right 1 171

NG conversion kit

1

59 Side shelf hooks 1 4 71a

NG Gas Hose with

Quick Connector

assembly

1

60

Side shelf front panel,

right

1 1 71b

NG Regulator assembly

1

61 Side shelf, right 1 1 71c

Truss Head Screw with

lock

2

62 Door, right 1 1 71d

Flat washer

2

63 Door, left 1 1 71e 6mm wrench 1

64 Door handle assembly 1 2 71f

6 mm Nut driver

1

65

Back panel rubber

grommet

11

KD-assembly hardware

pack

11

66 Spit fork 1 2 Grill cover 1 1

67 Spit rod 1 1 Manual 1

68 Rotisserie motor 1 1

69 Lighting rod 1 1

*Natural gas conversion kit sold separately

Assembly Instructions

1. Caster Assembly

Mount the casters onto the bottom panel (L) using

sixteen 1/4-in. x 15-mm truss head screws with

locking washers (AA) and sixteen ¼” flat washer

(EE).

The swivel caster with brake (Q) should be

positioned under the left rear of the cart bottom and

the swivel caster (P) should be positioned under

left front as shown in Fig. 1.

The two stationary casters (R ) should be

positioned under the right side.

Note: The gap of the two stationary casters should

be facing the inside bottom panel.

Turn over the bottom panel for assembling casters.

2. Side Panel Assembly

Use three 1/4-in. x 15-mm truss head

screws with locking washers (AA) to

connect the bottom of the left side panel (I)

to the bottom panel (L). Make the left side

panel flush with the rear of bottom panel

and tighten the screws as shown in Fig. 2.

Repeat for the right side panel (H).

Fig. 2

16 x EE

Fig. 1

I

6 x AA

L

H

16 x AA

L

Q

P

R

13

3. Back Panel, bottom Assembly

a). Position the back panel, bottom (G) with the flat

side facing outward. Attach the back panel, bottom

(G) to the bottom panel (L) with three 1/4-in. x 15-

mm truss head screws with locking washers (AA)

as shown in Fig. 3.

Fig. 3

Assembly Instructions

G

L

AA7X

b). Use four 1/4-in. x 15-mm truss head screws

with locking washers (AA) to connect the back

panel, bottom (G) to the right and left side

panels (H/I) as shown in Fig. 3

Fig. 4

4. Back Panel, middle Assembly

a). Use four 1/4-in. x 15-mm truss head screws

with locking washers (AA) to connect back

panel, middle (F) to the right and left side

panels (H / I )as shown in Fig. 4

F

4 x AA

I

H

I

H

14

L

H

I

Fig. 5

Fig.6

Assembly Instructions

5. Diagonal Bar Barrier Assembly

Use two 5/32-in. x 10-mm truss head screws (BB) to

attach Diagonal Bar Barrier (K) to the bottom panel (L)

and upside of the Back panel, bottom (G). As shown

in Fig. 5.

L

K

G

2 x BB

Fig.7

6. Door Triangle Bracket Assembly

a) Loosen but do not remove four 5/32-in. x

10-mm truss head screws (BB) mount the

Left Side Panel (I) and Bottom Panel (L),

two screws on cart Right Side Panel (H)

and two on the Bottom Panel (L). Align the

holes of the triangle bracket with screws on

Left Side Panel (I) and Bottom Panel (L).

Then tighten the screws as shown in Fig. 6.

b) Repeat the steps a) for attaching the

triangle bracket to the Right Panel (H) and

bottom Panel (L)

O

7. Cart frame Assembly

Use four 1/4-in. x 15-mm truss head

screws with locking washers (AA) to

add the cart frame (J) to the right and

left side panels, as shown in Fig. 7.

J

4 x AA

15

S

Fig. 8

Assembly Instructions

Fig.9

a) Attached the door handle assembly (U) to the

each door (S/T) using eight 5/32-in. x 10-mm

truss head screws (BB), as shown in Fig. 8.

HINT: Six screws for each door.

HINT: Four screws for each door.

12X

CC

8. Door Assembly

8X

T

U

BB

I

H

b). Attach the two door’s hinges to the right

and left side panels (I/H) using twelve 5/32-

in. x 10-mm flat head screws (CC) as

shown in Fig. 9.

16

Fig.10

Assembly Instructions

9. Install the Grease pan

a). Remove four 5/32-in. x 10-mm truss head screws and

four 5/32-in. flat washers which are pre-assembled on

the grease cup brackets (Z). Attach the grease cup

brackets (Z) on the grease pan (D) by using the same

four screws and flat washers that were previously

removed. Then tighten the screws as shown in fig. 10.

b). Install the grease pan (D) onto the cart by using

four 5/32” x10mm truss head screws (BB). As

shown in Fig. 11.

c). Install the grease cup (E) under the grease tray

(D). As shown in Fig. 12.

D

Fig.12

E

4 x BB

Z

D

Fig. 11

17

Fig.13

Assembly Instructions

Fig.14

10. Firebox Assembly

a). Remove the firebox assembly (A) from the

carton and carefully place onto the grill cart. As

shown in Fig. 13.

A

b) Attach firebox to the left and right side

panels by using four ¼-in. x 15-mm truss

head screws with locking washers (AA).

As shown in Fig. 14.

1 x AA

CAUTION The firebox assembly is heavy

and will require two or more people to lift and

position onto grill cart. Failure to do so may

result in injury.

1 x AA

18

2 x BB

11. Side Shelves Assembly

a). Loosen the two screws which pre-assembled

onto firebox right side panel (H) but do not

remove Completely. Align the bottom key holes

on side shelf (C) with the two loosened screws as

show in Fig. 15, and then tighten. .

b). Use three ¼-in x15-mm truss head screws with

locking washer (AA) to keep the right side shelf

in place (Insert the three screws from inside of

the firebox through the side shelf. Tighten

screws from inside the firebox). As shown in

Fig. 15.

Note: The top 3 screws of the firebox should be

screwed from the inside to outside for right side

burner shelf. But the bottom 2 screws should be

tightened from outside to inside.

c). Secure the right side shelf control panel and

main control panel by using two 5/32-in x 10-mm

truss head screws (BB) and two 5/32-in flat

washers (DD). As shown in Fig. 15.

Fig.15

Fig 16

Assembly Instructions

C

3 x AA

2 x DD

2 x BB

3 x AA

d) Repeat step 11 to assemble left side shelf.

As shown in Fig. 16.

H

19

Fig.17

V

W

X

12. Flame Tamers, Cooking Grids Installation

Place the flame tamers (X), main cooking grids (W), and

warming rack (V) into the grill as shown in Fig. 17.

13. Liquid Propane Tank Installation

Place the liquid propane tank into the hole

in the bottom panel and tighten the tank

bolt (M) at the back of the grill to secure as

shown in Fig. 18

Fig.18

M

14. Battery Assembly

Unscrew the electronic igniter button and place the

battery (Y) into the housing with the positive terminal

(+) facing outward. Replace the ignition button after

the battery has been installed as shown in Fig. 19.

Fig.19

Y

Assembly Instructions

20

La page charge ...

Nexgrill 720-0830D Le manuel du propriétaire

Nexgrill 720-0830D Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents