AT&T TL8901 Manuel utilisateur

User’s manual

TL8900/TL8901

DECT 6.0

accessory cordless headset

Congratulations

on your purchase of this AT&T product.

Enjoy up to 12 hours of hands-free talk time and crystal-clear

sound quality with the AT&T TL8900/TL8901 DECT 6.0 Accessory

Cordless Headset. Pair it wirelessly with compatible AT&T DECT

phones or other compatible DECT phones. Easy one-button

answer, volume and mute controls enhance wireless freedom,

while a range of up to 500 feet maximizes mobility. A magnetic

charger in the cradle ensures the headset ts and charges

securely—so you’ll never run out of battery during long calls.

Lightweight and comfortable, the headset oers multiple

wearing styles: over the ear, over the head or behind the neck.

Before using this AT&T product, please read the Important

safety information section on pages 37-39 of this manual.

Please thoroughly read this user’s manual for the feature

operations and troubleshooting information necessary to install

and operate your new AT&T product. You can also visit our

website at https://telephones.att.com or call

1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.

This telephone meets the California Energy Commission

regulations for energy consumption. Your telephone is set up to

comply with the energy-conserving standards right out of the

box. No further action is necessary.

Visit https://telephones.att.com/headsets for a

complete list of AT&T phones that have been tested and found to

be compatible with the TL8900/TL8901.

Model number: TL8900/TL8901

Type: DECT 6.0 accessory cordless headset

Serial number:

Purchase date:

Place of purchase:

Both the model and serial numbers of your AT&T product can be

found on the bottom of the headset charger.

Save your sales receipt and original packaging in case it is

necessary to return this product for warranty service.

the AT&T logo are trademarks of AT&T Intellectual Property licensed to

Advanced American Telephones, San Antonio, TX 78219. Printed in China.

Parts checklist

Check to make sure the headset package includes the following

items. Save your sales receipt and original packaging in the event

warranty service is necessary.

Cordless headset

with earbud

attached

Headset charger

Battery

with battery

compartment

cover attached

User's manual

Behind the neck

band

Headset charger

power adapter

Four over the ear hooks Over the head

bands

Four earbuds

Sponge

cover for ear

hooks

Two spare rubber

rings for headset

earpiece

User’s manual

TL8900/TL8901

DECT 6.0 cordless headset

User’s manual

TL8900/TL8901

DECT 6.0

accessory cordless headset

Table of contents

Getting started

Quick reference guide -

headset .............................................1

Headset lights ..............................2

Headset alert tones ..................3

Headset alert prompts ...........3

Quick reference guide -

headset charger ........................ 4

Installation ..........................................5

Battery installation ...................... 6

Headset charger installation

and battery charging...............7

Adding and registering

headsets ......................................... 8

Register a headset to the

SynJ SB67138 base ................... 9

Register a headset to an

AT&T DECT telephone

base ....................................................11

Deregistering headset .............. 13

Deregister headset from

the SynJ SB67138 base ......... 13

Deregister all devices from

an AT&T DECT telephone

base ................................................... 15

Headset attachments ............... 16

Over the ear hook .................... 16

Over the head band ................20

Behind the neck band ........... 23

Operation

Headset operation ......................26

Power on/o the headset ...26

Make a call .....................................26

Answer a call ................................26

End a call ........................................26

Headset ringer ........................... 27

Temporary ringer

silencing..........................................27

Call waiting ................................... 27

Options while on calls ...............28

Volume control .......................... 28

Mute ..................................................28

Multiple headsets use ........... 29

Appendix

Troubleshooting............................30

Maintenance .................................... 36

Important safety

information ..................................37

Safety information .................. 37

Especially about cordless

headsets ........................................38

Precautions for users

of implanted cardiac

pacemakers ................................. 39

Pacemaker patients ...............39

For C-UL compliance .................. 40

Mesures de sécurité

importantes .................................40

FCC Part 68 and ACTA ...............44

FCC Part 15 ........................................46

California Energy Commission

battery charging testing

instructions ..................................47

Limited warranty ..........................48

Technical specications ............51

DECT 6.0 digital

technology ....................................51

Operating range ........................51

Extended range and

clarity.................................................51

Index

Index ......................................................52

1

Quick reference guide - headset

Getting started

(On/o button and light)

X Press to make, answer or

end a call (page 26).

Earpiece

Battery with cover attached

X Remove to replace the

battery (page 6).

VOL+/FLASH/VOL-

X Slide the volume switch to

the right or le to adjust the

headset ringer volume while

in idle mode, or the listening

volume while on a call (page

27 or page 28).

X During a call, press to answer

an incoming call when you

receive a call waiting alert

(page 27).

MUTE

X Press to mute the

microphone during a call

(page 28).

X Press to mute the ringer in

the earpiece when there

is an incoming call (page

27).

Microphone

X The microphone

incorporates noise

canceling technology for

clearer calls.

4

5

6

3

2

1

Getting started

2

Quick reference guide - headset

Color

LED light status

Meaning

Red Steady light on The battery is low and the headset

is charging in the headset charger.

Flash every 10 seconds The battery is low and the headset

is not in the headset charger.

Flash 3 times Powering o.

Blue Steady light on The battery is fully charged.

Flash every 10 seconds The headset is not in the headset

charger.

Flash 2 times every

3 seconds

The headset is in use.

Flash 3 times Powering on.

Flash 4 times every

4 seconds

There is an incoming call.

Purple Steady light on The battery is well charged.

Red and

blue

Alternate slowly The headset is not registered.

Alternate quickly The headset is trying to register to

a telephone base.

O Light o The battery is depleted.

No battery is installed.

The headset is powered o.

Headset lights

Getting started

3

Alert tone behavior Meaning

One short beep every

30 seconds

X The microphone is muted.

Two beeps X Error alert tone.

X The speaking volume has reached its

highest or lowest setting.

X Any key is pressed while the headset is out

of range.

Two low beeps X Call waiting alert tone.

Two rapid beeps

every 20 seconds

X Low battery warning.

Three rapid beeps

every 20 seconds

X The headset is out of range.

Three rapid beeps X The headset is powering on or o.

Headset alert tones

Alert prompt Meaning

“Mute on” X The microphone is muted.

“Mute o” X The microphone is re-activated.

“Not registered”

X

ON/OFF button is pressed while the

headset is not registered.

“Out of range” X The headset is on a call and out of range.

X Any key is pressed while the headset is out

of range.

“Low battery”

X

ON/OFF button is pressed while the

headset battery is low.

Headset alert prompts

Quick reference guide - headset

Getting started

4

Quick reference guide - headset charger

Power jack

Magnetic charging mount

Place the headset here for

charging.

Power cord slot

Route the power cord

through the slot.

Getting started

5

Installation

See pages 6-7

for easy instructions.

You must install and

charge the battery

before using the headset.

For customer service or product information, visit our website at

https://telephones.att.com or call 1 (800) 222-3111. In

Canada, dial 1 (866) 288-4268.

Avoid placing the charger too close to:

X Communication devices such as television sets, VCRs or other

cordless telephones.

X Excessive heat sources.

X Noise sources such as a window with trac outside, motors,

microwave ovens, refrigerators or uorescent lighting.

X Excessive dust sources such as a workshop or garage.

X Excessive moisture.

X Extremely low temperature.

X Mechanical vibration or shock such as on top of a washing

machine or work bench.

Getting started

6

Battery installation

The battery is permanently attached to the battery

compartment cover. Do not try to separate them from each

other. After installing the battery, charge it for at least 15

minutes. You may be able to make and receive short calls. For

optimal performance, charge the headset battery for at least

three hours before use. When fully charged, the headset battery

provides approximately 12 hours of talk time or 5 days of standby

time. When the headset is not in use, recharge it by returning it

to the headset charger.

1. Insert the battery into the

battery compartment.

2. Press down on the battery

until it clicks into place.

1

2

NOTES:

X Remove any headset attachment before battery replacement.

X You will hear the voice prompt "Low battery" when you press the button

while the headset battery is low.

X To order a replacement battery (model BT291665), visit our website at

https://telephones.att.com or call 1 (800) 222-3111. In

Canada, dial 1 (866) 288-4268.

Getting started

7

Headset charger installation and battery charging

After installing the battery, charge the headset by placing it in

the magnetic charging mount, as shown below. The light turns

on when the headset is charging.

IMPORTANT INFORMATION

Use only the supplied rechargeable battery pack or replacement

battery pack (model BT291665). To order, visit our website at

https://telephones.att.com or call 1 (800) 222-3111. In

Canada, dial 1 (866) 288-4268.

1. Plug the small end of the headset charger power adapter

into the power jack at the bottom of the headset charger.

Route the power cord through the power cord slot. Plug the

large end of the power adapter into an electrical outlet not

controlled by a wall switch.

3. The magnet holds the top

of the headset in place.

The light turns on.

Magnetic

charging

mount

2. Insert the headset into the

magnetic charging mount.

Getting started

8

Adding and registering headsets

You must register your new TL8900/TL8901 headset to one of

the following devices before use:

X SynJ SB67138 base (see pages 9-10).

X A compatible AT&T DECT 6.0 telephone (see pages 11-12).

Visit https://telephones.att.com/headsets for a list of

compatible telephones.

Refer to the user’s manual of your telephone for the maximum

number of handsets and headsets that you can register to

the telephone. If you have the maximum number of handsets/

headsets registered, you need to follow the deregistration

instructions (see pages 13-15) to deregister all registered

devices before you can register this new headset.

You can only register the headset to one device at a time. You

must deregister the headset before registering it to another

telephone.

Getting started

9

Register a headset to the SynJ SB67138 base

1. Place the headset in the headset charger and

allow it to charge for at least five minutes

before beginning registration. Make sure the

headset is out of the headset charger before

you begin registration.

2. On the telephone base, press MENU/ENTER.

3. Scroll down to Registration and then press

MENU/ENTER.

4. Press MENU/ENTER again to select

Register HS. The telephone base shows

Registering new device....

5. Place the headset into the charger. It

takes up to 60 seconds to complete the

registration. The telephone base shows

Cordless headset registered and beeps

when the registration is successful.

It takes about 60 seconds to complete the

registration process. The light turns red when

the headset is registered but not fully charged,

or turns blue when it is registered and fully charged.

To verify the registration, press the button on

the headset and check for a dial tone. If you hear a

dial tone and the extension

0

icon appears on the

telephone base, the registration was successful. If

the registration fails, you hear the voice prompt, “Not

registered” and the light on the headset flashes

slowly in red and blue.

Adding and registering headsets

COVM

Speed dial setup

Customer support

Registration

>

Register HS

Deregistration

>

Cordless headset

registered

Registering

new device...

Line1 00:00:05

0

Getting started

10

Register a headset to the SynJ SB67138 base (cont.)

If the registration was not successful, remove it from the headset

charger and try the registration process again.

If you have a dial tone but an extension number other than

0 displays on the telephone base, the headset is registered

as a handset and will not function properly. If this is the case,

you must deregister and start over. See the deregistration

procedures on page 13.

Adding and registering headsets

Getting started

11

Register a headset to an AT&T DECT telephone base

1. Make sure the battery is properly installed in

the headset (see page 6). The light on the

headset flashes slowly in red and blue to indicate

the headset is not registered.

2. Place the headset in the headset charger and

allow it to charge for at least one hour before

beginning registration.

3. Remove the headset from the charger.

4. On the telephone base, press and hold

/HANDSET LOCATOR or FIND HS until the

red IN USE light turns on (about four seconds) and

then release the button.

If your telephone base has no

/HANDSET LOCATOR or FIND HS button:

Press and hold the HOLD button until the screen

displays Registering... Please wait, then release

the button.

-OR-

Press and hold the /LOCATOR button until

the screen displays Registering handset..., then

release the button.

5. Place the headset back to the charger. The light flashes

quickly in red and blue.

Adding and registering headsets

Getting started

12

Register a headset to an AT&T DECT telephone base

(cont.)

It takes about 60 seconds to complete the registration process.

The light turns red when the headset is registered but not fully

charged, or turns blue when it is registered and fully charged.

To verify the registration, press the button on the headset and

check for a dial tone. If the registration fails, you hear the voice

prompt "Not registered" and the light on the headset flashes

slowly in red and blue.

To reset the headset, remove it from the headset charger and try

the registration process again.

NOTE:

The button used for registration on your telephone system may be different. Refer to the

user's manual of your telephone for detailed information.

Adding and registering headsets

Getting started

13

Deregistering headset

You may need to deregister your headsets if:

X You have already registered the headset and now wish to register

your headset to a dierent telephone base.

-OR-

X You have registered the maximum number of headsets and

need to replace one of them. You must rst deregister all

headsets, and then register each headset you wish to use

again, one at a time.

Please read carefully through all the instructions in this

section before beginning the deregistration process.

Deregister headset from the SynJ SB67138 base

If you already have 10 registered devices and need to replace or

add a new device, or if you wish to change the assigned extension

numbers of your devices, you must deregister the desired

device(s) first, then register the device(s) you wish to use, one

at a time. Deregistering a cordless handset or deskset does not

remove the data saved on that device.

Please make sure the telephone system is not in use before

deregistration. To deregister a headset from the telephone base:

1. On the telephone base, press MENU/ENTER.

2. Scroll down to Registration and

press MENU/ENTER.

3. Scroll down to Deregistration and then

press MENU/ENTER.

4. The telephone base screen shows

Deregister:. Scroll to choose the desired

headset, then press MENU/ENTER.

COVM

Speed dial setup

Customer support

Registration

>

Register HS

Deregistration

Deregister:

>Headset 1

Deskset 2

All

Getting started

14

Deregistering headset

Deregister headset from the SynJ SB67138 base (Cont.)

5. The telephone base screen prompts if you

want to deregister the headset. Press

REP to exit or press SKIP to continue the

deregistration.

6. If you press SKIP , the telephone base

shows Deregistering. It takes up to 10

seconds to complete the deregistration.

When the deregistration is successful, there

is a conrmation tone and the telephone

base shows the deregistration completion

message.

Deregistering

Headset 1

deregistered

Deregister

Headset 1?

<=No >=Yes

La page charge ...

AT&T TL8901 Manuel utilisateur

Ce manuel convient également à

AT&T TL8901 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents