EarthQuake 31043 Le manuel du propriétaire

Catégorie
Mini motoculteurs
Taper
Le manuel du propriétaire

Ce manuel convient également à

GAS/OIL
RATIO
50:1
P/N: 31050
ECN: 12675
REV1: 10/23/19
© 2020 Ardisam, Inc.
All Rights Reserved
Tous droits réservés
Todos los derechos reservados
ENGLISHFRANÇAIS
Get parts or technical assistance online at
www.GetEarthquake.com or call (800) 345-6007
Pièces détachées et assistance technique en ligne à
www.GetEarthquake.com ou composer le (800) 345-6007
Obtenga piezas o asistencia técnica en línea en
www.GetEarthquake.com o llame al (800) 345-6007
Owners Manual
Manuel de l’utilisateur
Badger™
Front Tine Tiller
Model Numbers, Numéros de modèle:
31043
Operator’s Manual
BADGER Front Tine Tiller
2 For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST
INTRODUCTION
Thank you for purchasing the BADGER Tiller from Earthquake®. We have worked to ensure that this tiller meets the highest stan-
dards for usability and durability. With proper care, your tiller will provide many years of service.
Please read this entire manual before installation and use. Earthquake® reserves the right to change, alter or improve the
product and this document at any time without prior notice.
CONTENTS
Introduction/Contents/Registration and Service ............................................................................................................................................................. 2
Warnings and Safety Precautions .......................................................................................................................................................................................3-6
Safety Decals ..................................................................................................................................................................................................................................7
Hazard Symbols and Meanings ...............................................................................................................................................................................................8
Features ...........................................................................................................................................................................................................................................9
Unpacking and Assembly ................................................................................................................................................................................................ 10-12
Controls and Operating Symbols/Controls ................................................................................................................................................................ 12-13
Operation ......................................................................................................................................................................................................................................14
Maintenance .........................................................................................................................................................................................................................15-17
Storage ...........................................................................................................................................................................................................................................17
Troubleshooting and Repair ................................................................................................................................................................................................... 18
OWNERSHIP RECORDS
Owners Name:
Owners Address:
City: State/Province: Zip Code/Postal Code:
Model Number: Serial Number:
Date of Purchase:
Notes:
Record the product model number and serial number in the space
provided for easy reference when ordering parts or requesting
technical support. Excluding emissions-related warranty items, the
warranty is valid only if the completed registration is received by
Ardisam within 30 days of purchase. (SEE WARRANTY SECTION FOR
MORE INFORMATION) You can register your warranty online by vis-
iting www.getearthquake.com, or by mailing it to: Ardisam, 1160
8th Avenue, Cumberland, WI 54829. You may also call our Custom-
er Service department at (800) 345-6007 Mondays through Fridays
from 8 a.m. to 5 p.m. CST.
Read and keep this manual for future reference. This manual contains important information on SAFETY, ASSEMBLY, OP-
ERATION, AND MAINTENANCE. The owner must be certain that all the product information is included with the unit. This
information includes the MANUAL, the REPLACEMENT PARTS and the WARRANTIES. This information must be included to
make sure state laws and other laws are followed. All persons to whom rent/loan this unit must have access to and under-
stand this information. This manual should remain with the product even if it is resold.
Registration and Service
Serial
Number
Decal
Operator’s Manual
BADGER Front Tine Tiller
3For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST
WARNINGS AND SAFETY PRECAUTIONS
Owners Responsibility
Accurate assembly and safe and eective use of the machine is
the owner’s responsibility.
Read and follow all safety instructions.
Carefully follow all assembly instructions.
Maintain the machine according to directions and
schedule included in this Earthquake® operators
manual.
Ensure that anyone who uses the machine is familiar
with all controls and safety precautions.
Special Messages
Your manual contains special messages to bring attention to
potential safety concerns, machine damage as well as helpful
operating and servicing information. Please read all the infor-
mation carefully to avoid injury and machine damage.
NOTE: General information is given throughout the
manual that may help the operator in the
operation or service of the machine.
THIS SYMBOL POINTS OUT IMPORTANT
SAFETY INSTRUCTIONS WHICH IF NOT
FOLLOWED COULD ENDANGER YOUR
PERSONAL SAFETY. READ AND FOLLOW ALL
INSTRUCTIONS IN THIS MANUAL BEFORE
ATTEMPTING TO OPERATE THIS EQUIPMENT.
Before Operating Equipment:
Please read this section carefully. Read entire operating and
maintenance instructions for this product. Failure to follow in-
structions could result in serious injury or death. Operate the
machine according to the safety instructions outlined here and
inserted throughout the text. Anyone who uses this machine
must read the instructions and be familiar with the controls.
Intended Use / Foreseeable Misuse
IMPORTANT: This is a motorized rotary tiller that works the
soil by means of rotating tines. It is pedestrian-controlled, but
not self-propelled, with a gasoline-fueled internal combustion
engine to power the tines. It shall not be used for any other
purpose.
DANGER
SRT CRT
WARNING
WARNING INDICATED A HAZARD WHICH, IF NOT
AVOIDED, COULD RESULT IN DEATH OR SERIOUS
INJURY AND/OR PROPERTY DAMAGE.
CAUTION
CAUTION INDICATES A HAZARD WHICH, IF NOT
AVOIDED, COULD RESULT IN PERSONAL INJURY AND/
OR PROPERTY DAMAGE.
DANGER
DANGER INDICATES A HAZARD WHICH, IF NOT
AVOIDED, CERTAINLY WILL RESULT IN DEATH OR
SERIOUS INJURY AND/OR PROPERTY DAMAGE.
WARNING
YOU MUST READ, UNDERSTAND AND COMPLY WITH
ALL SAFETY AND OPERATING INSTRUCTIONS IN
THIS MANUAL BEFORE ATTEMPTING TO SETUP AND
OPERATE YOUR MACHINE.
FAILURE TO COMPLY WITH ALL SAFETY AND
OPERATING INSTRUCTIONS CAN RESULT IN LOSS OF
MACHINE CONTROL, SERIOUS PERSONAL INJURY TO
YOU AND/OR BYSTANDERS, AND RISK OF EQUIPMENT
AND PROPERTY DAMAGE. THE TRIANGLE IN THE TEXT
SIGNIFIES IMPORTANT CAUTIONS OR WARNINGS
WHICH MUST BE FOLLOWED.
WARNING
CALIFORNIA PROPOSITION 65 WARNING
ENGINE EXHAUST FROM THIS PRODUCT CONTAINS
CHEMICALS KNOWN TO THE STATE OF CALIFORNIA
TO CAUSE CANCER, BIRTH DEFECTS, OR OTHER
REPRODUCTIVE HARM.
IMPORTANT
IMPORTANT INDICATES HELPFUL INFORMATION FOR
PROPER ASSEMBLY, OPERATION, OR MAINTENANCE
OF YOUR EQUIPMENT.
NOTICE
NOTICE INDICATES YOUR EQUIPMENT CAN BE
DAMAGED IF THE SAFETY INSTRUCTIONS THAT
FOLLOW THIS SIGNAL WORD ARE NOT OBEYED.
Operator’s Manual
BADGER Front Tine Tiller
4 For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST
GENERAL SAFETY RULES
Read, understand, and follow all instructions on the
machine and in the manual(s). Be thoroughly familiar with
the controls and the proper use of the machine before
starting.
Use this equipment for its intended purpose only.
Familiarize yourself with all of the safety and operating
decals on this equipment and on any of its attachments or
accessories.
Do not put hands or feet near or under rotating parts.
Only allow responsible individuals who are familiar with the
instructions to operate the machine. Do not allow children
to operate this machine. Do not allow adults to operate the
machine without proper instruction.
Thoroughly inspect the area where the machine is to be
used and remove all foreign objects. Your equipment can
propel small objects at high speed causing personal injury
or property damage. Stay away from breakable objects,
such as house windows, automobiles, greenhouses, etc.
Wear appropriate clothing such as a long-sleeved shirt
or jacket. Also wear long trousers or slacks. Do not wear
shorts. Never wear sandals, sneakers or open shoes, and
never operate the machine with bare feet.
Do not wear loose clothing or jewelry. They can get caught
in moving parts. Always keep hands, feet, hair and loose
clothing away from any moving parts on engine and
machine.
Always wear safety goggles or safety glasses with side
shields when operating the machine to protect your eyes
from foreign objects which can be thrown from the unit.
Always wear a protective hearing device.
Always wear work gloves and sturdy footwear. Wear
footwear that will improve footing on slippery surfaces.
Leather work shoes or short boots work well for most
people. These will protect the operator’s ankles and shins
from small sticks, splinters, and other debris.
It is advisable to wear protective headgear to prevent the
possibility of being struck by small ying particles, or being
struck by low hanging branches, twigs, or other objects
which may be unnoticed by the operator.
Do not operate the machine without proper guards or
other safety protective devices in place.
See manufacturers instructions for proper operation and
installation of accessories. Only use accessories approved
by the manufacturer.
Operate only in daylight or good articial light.
Do not operate product when fatigued or under the
inuence of alcohol, drugs or other medication which
can cause drowsiness or aect your ability to operate this
machine safely.
Never operate machine in wet grass. Always be sure of
your footing; keep a rm hold on the handle and walk;
never run.
Watch for trac when operating machine near, or when
crossing roads.
If the equipment should start to vibrate abnormally,
stop the engine (motor), ip the ON/OFF switch to the
OFF position. Check immediately for cause. Vibration is
generally a warning of trouble. If the noise or vibrations of
the machine increase, stop immediately and perform an
inspection.
Never leave the machine unattended when the engine is
running. Flip the ON/OFF switch to the OFF position.
Regularly inspect the machine. Make sure parts are not
bent, damaged, or loose.
Temperature of muer and nearby areas may exceed 150°
F (65° C). Allow muer and engine areas to cool before
touching. Never pick up or carry the machine while the
engine is running.
Prolonged exposure to noise and vibration from gasoline
engine-powered equipment should be avoided. Take
intermittent breaks and/or wear ear protection from engine
noise as well as heavy work gloves to reduce vibration in the
hands.
Keep all screws, nuts, and bolts tight.
Do not transport the machine from one place to another
with the engine running.
When moving the packaged machine, always do so with a
partner.
Check local regulations for age restrictions on use of this
machine.
Product-Specic Safety Rules
Do not till above underground utilities, including water
lines, gas lines, electric cables, or pipes. Do not operate the
machine on terrain/soil with large rocks and foreign objects
which can damage the equipment.
After striking a foreign object, stop the engine. Flip the ON/
OFF switch to the OFF position. Inspect the machine for
damage. If damaged, repair before starting and operating
the machine.
The tines of the tiller should not rotate when the drive
control lever is released into the neutral position. If it does
rotate when in neutral, contact Earthquake® Customer
Service for instruction.
If an object becomes lodged in the tines, ip the ON/OFF
switch to the OFF position, allow to cool before attempting
to remove the foreign object.
Pulleys and belts should be kept free of oil or other
moisture for ecient operation.
Disengage all clutches and leave control lever in the neutral
position before starting the engine.
Operator’s Manual
BADGER Front Tine Tiller
5For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST
ENGINE SAFETY PRECAUTIONS
If your product comes with a separate engine
manual, be sure to read and follow all safety and
warning precautions outlined there, in addition
to any in this manual.
Preventing Carbon Monoxide Poisoning
Always start and run engine outdoors. Do not start or run
engine in an enclosed area, even if doors or windows are
open.
Never try to ventilate engine exhaust indoors. Carbon
monoxide can reach dangerous levels very quickly.
Never run engine outdoors where exhaust fumes may be
pulled into a building.
Never run engine outdoors in a poorly ventilated area
where the exhaust fumes may be trapped and not easily
taken away. (Examples include: in a large hole or areas
where hills surround your working area.)
Never run engine in an enclosed or partially enclosed area.
(Examples include: buildings that are enclosed on one or
more sides, under tents, car ports or basements.)
Always run the engine with the exhaust and muer
pointed in the direction away from the operator.
Never point the exhaust muer towards anyone. People
should always be many feet away from the operation of the
engine and its attachments.
Do not change the engine governor settings or over-speed
the engine.
Gasoline Fires and Handling Fuel Safely
Use extra care in handling gasoline and other fuels. They are
ammable and vapors are explosive.
When storing extra fuel be sure that it is in an appropriate
container and away from any re hazards.
Prevent re and explosion caused by static electric
discharge. Use only nonmetal, portable fuel containers
approved by the Underwriter’s Laboratory (U.L.) or the
American Society for Testing & Materials (ASTM).
Never remove the fuel cap or add fuel with the engine
running. Stop engine and allow to cool before lling.
Do not smoke while using engine or product.
Never drain fuel from engine in an enclosed area.
Always ll fuel tank outside in a well ventilated area. Never
ll your fuel tank with fuel indoors. (Examples include:
basement, garage, barn, shed, house, porch, etc.) Never
ll tank near appliances with pilot lights, heaters, or other
ignition sources. If the fuel has to be drained, this should
be done outdoors. The drained fuel should be stored in a
container specically designed for fuel storage or it should
be disposed of carefully.
Always wipe up excess (spilled) fuel from engine before
starting. Clean up spilled fuel immediately. If fuel is spilled,
do not start the engine but move product and fuel container
from area. Clean up spilled fuel and allow to evaporate and
dry after wiping and before starting.
Allow fuel fumes/vapors to escape from the area before
starting engine.
Test the fuel cap for proper installation before starting and
using engine.
Always run the engine with fuel cap properly installed on
the engine.
Never smoke while relling engine fuel tank.
Do not store engine with fuel in fuel tank indoors. Fuel and
fuel vapors are highly explosive.
Preparation
Dress appropriately when operating the tiller. Always wear
sturdy footwear. Never wear sandals, sneakers or open
shoes, and never operate the tiller with bare feet. Do not
wear loose clothing that might get caught in moving parts.
Carefully inspect the area to be tilled and remove all foreign
objects. Do not till above underground water lines, gas
lines, electric cables, or pipes. Do not operate the tiller in
soil with large rocks and foreign objects which can damage
the equipment.
Disengage all clutches and leave control lever in the neutral
position before starting the engine.
Handle fuel with care; it is highly ammable.
a. Use an approved fuel container.
b. Never add fuel to a running engine or hot engine.
c. Fill fuel tank outdoors with extreme care. Never ll fuel
tank indoors.
d. Replace gasoline cap securely and clean up spilled fuel
before restarting.
WARNING
ENGINES GIVE OFF CARBON MONOXIDE, AN
ODORLESS, COLORLESS, POISONOUS GAS. CARBON
MONOXIDE MAY BE PRESENT EVEN IF YOU DO NOT
SMELL OR SEE ANY ENGINE EXHAUST. BREATHING
CARBON MONOXIDE CAN CAUSE NAUSEA, FAINTING
OR DEATH, IN ADDITION TO DROWSINESS, DIZZINESS
AND CONFUSION.
IF YOU EXPERIENCE ANY OF THESE SYMPTOMS, SEEK
FRESH AIR AND MEDICAL ATTENTION IMMEDIATELY.
Operator’s Manual
BADGER Front Tine Tiller
6 For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST
OPERATION
Do not operate tiller under the inuence of alcohol or
drugs.
Never operate tiller without guards, covers, and hoods in
place.
Keep hands, feet, and clothing away from rotating parts.
Keep clear of tiller tines at all times.
Tines rotate when tiller is engaged; tines rotate when the
drive safety control lever is pulled down. Releasing the
drive safety control lever to neutral stops the tines.
Use extreme caution when operating on or crossing gravel
drives, walks, or roads. Stay alert for hidden hazards or
trac.
After striking a foreign object, stop the engine, remove the
wire from the spark plug, thoroughly inspect the tiller for
any damage, and repair the damage before restarting and
operating the tiller.
If vegetation clogs the tines, stop the engine and
disconnect the spark plug wire before removing vegetation
by hand.
If the unit should start to vibrate abnormally, stop the
engine and check immediately for the cause. Vibration is
generally a warning of trouble.
Do not run the engine indoors; exhaust fumes are deadly.
Do not overload the machine capacity by attempting to till
too deep at too fast of a rate.
Never operate the tiller without good visibility or light.
Be careful when tilling in hard ground. The tines may catch
in the ground and propel the tiller forward. If this occurs, let
go of the handle bars and do not restrain the machine.
Take all possible precautions when leaving the machine
unattended. Disengage control lever, stop the engine, wait
for all moving parts to stop, and make certain guards and
shields are in place.
When leaving the operating position for any reason:
- Shut o the engine.
- Wait for all moving parts to stop.
MAINTENANCE AND STORAGE
Keep machine, attachments and accessories in safe
working condition.
Check shear bolts, engine mounting bolts and other bolts
at frequent intervals for proper tightness to be sure the
equipment is in safe working condition.
To prevent accidental starting, always disconnect and
secure the spark plug wire from the spark plug before
performing tiller maintenance.
Never run the engine indoors. Exhaust fumes are deadly.
Always allow muer to cool before lling the fuel tank.
Never store equipment with gasoline in the tank inside
a closed building where fumes may reach an open ame
or spark. Allow the engine to cool before storing in any
building.
Always refer to the operators guide instructions for
important details if the tiller is to be stored for an extended
period.
WARNING
THE RIGHT AND LEFT SIDES
OF YOUR ROTOTILLER ARE
DETERMINED FROM THE
OPERATING POSITION AS
YOU FACE THE DIRECTION
OF FORWARD TRAVEL.
ENGINE IS SHIPPED FROM FACTORY WITHOUT OIL.
YOU MUST ADD ENGINE OIL BEFORE STARTING
ENGINE.
L R
WARNING
HOT GASES ARE A NORMAL BYPRODUCT OF A
FUNCTIONING INTERNAL COMBUSTION ENGINE.
FOLLOW ALL SAFETY INSTRUCTIONS TO PREVENT
BURNS AND FIRES.
DO NOT ALTER/MODIFY ENGINE:
NEVER ALTER OR MODIFY THE ENGINE FROM THE
FACTORY. SERIOUS INJURY OR DEATH MAY OCCUR IF
ENGINE IS MODIFIED OR ALTERED.
WHEN WORKING ON OR REPLACING PARTS FOR THE
ENGINE OR PRODUCT, YOU MUST ALWAYS FLIP THE
ON/OFF SWITCH TO THE OFF POSITION.
Operator’s Manual
BADGER Front Tine Tiller
7For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST
Part No. 17047
PINCH POINT WARNING
Tail Mount Decal
Part No. 17052
MOVING PARTS WARNING
Frame Near Belt Decal
Part No. 17050
TINES DANGER/OPERATION
Hood Decal
Part No. 17049
MULTI INJURY WARNING
Hood Decal
SAFETY DECALS
This rototiller unit has been designed and manufactured to provide you with the safety and reliability you would expect from an
industry leader in outdoor power equipment manufacturing.
Although reading this manual and the safety instructions it contains will provide you with the necessary basic knowledge to
operate this equipment safely and eectively, we have placed several safety labels on the tiller to remind you of this important
information while you are operating the unit.
These important safety labels are illustrated below, and are shown here to help familiarize you with the location and content of
the safety messages you will see as you perform normal tilling operations. Please review these decals now, and if you have any
questions regarding its meaning or how to comply with these instructions, reread the complete safety instruction text in this
manual. For additional questions call Earthquake® Customer Service.
15698
Part No. 15698
DECAL PICTORIAL LEVER
CLUTCH ENGAGEMENT
Right Handle Bar and Drive
Control Lever
When starting engine,
place free hand here.
Pour démarrer le moteur,
placer le main libre ici.
17918
Part No. 17918
DECAL PLACE FREE HAND HERE
Left Handle Bar
Part No. 17920
CORRECT TINE INSTALLATION
Operator’s Manual
BADGER Front Tine Tiller
8 For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST
HAZARD SYMBOLS AND MEANINGS
A: Warning!
B: Avoid Injury From Rotating Tines.
C: Read Owners Manual Before Operating Machine.
D: Remove Objects that Could Be Thrown By This Machine.
E: Dangerous Moving Parts.
F: Be Aware of Moving and Rotating Parts.
G: Wear Ear and Eye Protection At All Times.
H: Do Not Service or Adjust Moving Parts Unless Engine is Stopped and Spark Plug
Wire is Disconnected.
I: Dress Appropriately And Wear Sturdy Footwear.
J: Toxic Fumes—Do Not Operate in Unventilated Areas.
K: Hot Surfaces.
L: Fire Hazards.
M: Do Not Use In Thunderstorms—For severe weather, stop operation of this
machine and seek shelter.
N: Team Lift—For your safety, always have at least two people when lifting this
machine.
O: Do Not Till Above Underground Utility Lines And Pipes.
P: Do Not Operate When Children Or Others Are Around.
A
B
C
D E F
G H
I
J
K
L
M
N
O P
Operator’s Manual
BADGER Front Tine Tiller
9For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST
FEATURES
The advantage of the Earthquake® BADGER gear drive Front Tine Rototiller, over other tillers, is the
exclusive hinged tail mount, wheel and drag stake assembly. This feature gives the tiller its stability and
versatility. For easy transport and quick turning in the garden, fold the wheels under the engine. During
operation, the wheels unfold back and the drag stake folds down. The long length between the tines and
the drag stake make this the most comfortable handling front tine tiller on the market. SEE FIGURE 1
TRANSPORT POSITION OPERATING POSITION
DRIVE SAFETY
CONTROL LEVER
KNOBBY
COMFORT
GRIPS
3-POSITION
HANDLE
BAR HEIGHT
ADJUSTMENT
LARGE 2-POSITION
WHEELS
ADJUSTABLE
DRAG STAKE
TINE SHIELD
3-WAY ADJUSTABLE
TINE WIDTHS
ADJUSTABLE
FORWARD
CABLE
BUMPER
FRONT
BELT
COVER
HINGED CAST-IRON TAIL MOUNT
DURABLE FORGED TINES
FIGURE 1
Operator’s Manual
BADGER Front Tine Tiller
10 For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST
UNPACKING AND ASSEMBLY
Carton Contents
Front Tine Rototiller
Parts Bag (with manuals and assembly hardware parts packet)
Parts Box (with outer tines, wheel axle, and drag stake)
2x Wheels
Handlebar Assembly
Tine Shield
Bottle of Viper® 4-Cycle Oil
Tools Required for Assembly
Utility knife or box cutter
2x 10 mm Wrench
2x 13 mm Wrench
NOTE: Socket head wrench may make assembly easier,
but is not necessary.
ASSEMBLY
1. a. Open top of carton and remove handlebar assembly,
wheels, parts bag, tine shield, and bottle of oil.
b. Parts Packet contains:
4 - Bolts M8 X 1.25 X 20MM
2 - Hairpin 2.5 Dia. X 35MM
1 - Pin Lock 8 X 40MM
4 - Washers M8 X 24 X 2.0MM
2 - Bolts M8 X 1.25 X 45
6 - Nut M8 Nylock
2 - Washer 12MM
4 - Bolts M6 X 1.0 X 16MM
4 - Nut M6 Nylock
1 - Drag Stake Handle Assembly (Incl. M6 Bolt & Nut)
NOTE: Plastic side of Nylock nut must face away from
bolt head during assembly. SEE FIGURE 8
2. Cut all four corners of box so it lies at on the ground.
3. Pull out parts box and remove contents.
4. Assemble axle to lower tail mount. Install wheels on each
end of axle; install 12 MM washers onto axle against wheels;
insert hairpins into holes in axle to keep washers and
wheels in place. SEE FIGURE 3
5. Install tine shield using four M6 bolts and four M6 nylock nuts.
Line up slots on both sides of shield and insert both bolts and
nuts in place before fully tightening. SEE FIGURE 4
NOTE: Dirt shield must be between engine mount deck
and tine shield.
6. Assemble tines to unit.
a. Assemble outer tines to unit using two M8 bolts and
two M8 nylock nuts. The arrow on the tines must point
in the direction of forward rotation.
b. Outside tines have two positions- wide 21" and narrow
16". For narrow width, assemble with short side of tine
holder pipe towards center of machine. SEE FIGURE 5
c. For wide width, move the left tine to the right side and
right tine to the left side. Assemble with the long side
of tine pipe towards machine, making sure arrow on the
tines are pointing in the direction of forward rotation.
SEE FIGURE 6
FIGURE 2
Tail mount casting allows tiller to be in two dierent positions:
working and transport. When transitioning from working
position into transport position, or vice versa, be careful of the
breach between the upper and lower tail mount casting to avoid
pinching hazards.
Working Position
Transport Position
CAUTION
HANDLE ROTOTILLER WITH CARE. DO NOT DAMAGE
THROTTLE CABLE WHEN TRANSPORTING OR
OPERATING.
IMPORTANT
IT IS RECOMMENDED THAT TWO PEOPLE ASSEMBLE
ROTOTILLER TOGETHER. ASSEMBLING ROTOTILLER
ALONE MAY MAKE ASSEMBLY MORE DIFFICULT AND
INCREASE RISK OF INJURY.
WARNING
DO NOT LIFT ROTOTILLER FROM CARTON. ROTOTILLER
IS HEAVY AND CAN CAUSE INJURY. CUT BOX AWAY
FROM ROTOTILLER TO ACCESS MACHINE AND PARTS.
WARNING
KEEP HANDS AND FEET AWAY FROM TAIL MOUNT
CASTING. FAILURE TO DO SO MAY RESULT IN SERIOUS
INJURY. SEE FIGURE 2
Operator’s Manual
BADGER Front Tine Tiller
11For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST
7. a. Assemble the upper handle bar assembly onto the
lower loop mount using four M8 bolts, four M8 at
washers and four M8 locknuts. The handlebar as well as
the bolt should go on the outer side of the lower loop
mount, while the washer and nut should be placed on
the inside. SEE FIGURES 7 & 8
b. The upper two bolts can be assembled through one of
three hole positions depending on the user’s preferred
handle bar height (low, middle, high). For the highest
height, insert bolt into the most forward hole. For the
lowest height, insert bolt into the most rear hole. SEE
FIGURE 7
8. Insert depth regulator/drag stake through bottom opening
in lower tail mount and secure with lock pin. Assemble
drag stake handle onto drag stake using accompanying M6
Bolt and Nut. SEE FIGURE 9
FIGURE 4
Dirt
Shield
Tine Shield
Engine
Mount Deck
High
Position
Medium
Position
Low
Position
Upper Bolt
Lower Bolt
Lower Loop Mount
FIGURE 7
FIGURE 3
Lower Tail
Mount
Washer
Wheel
Hairpin
FIGURE 5
FIGURE 6
Narrow
Tine
Width
Wide Tine
Width
Nylock
Nut
FIGURE 8
Drag Stake
FIGURE 9
Lock Pin
Drag Stake
Operator’s Manual
BADGER Front Tine Tiller
12 For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST
Fill Engine Crankcase
1. Add oil according to engine manual. Do not overll.
Use a clean, high quality detergent oil. Use no special
additives with recommended oils. Do not mix oil with
gasoline. Oil level must be full. Check the oil level by
checking the engine’s oil dipstick if provided, or by
removing oil ll plug. Oil level should be up to the
bottom of the ll plug opening.
2. Always check oil level before starting engine. Refer to
engine manual for capacity and type of oil to use.
CONTROL AND OPERATING SYMBOLS
FIGURE 10 shows common control and operating symbols
that may be found on the unit or in this manual. Before you
operate your unit, learn and understand the purpose for each
symbol.
Choke
On/O Fuel Shuto
CONTROLS
Drive Safety Control Lever
Pulling down on the drive safety control lever engages the
tines. Releasing the drive safety control lever disengages the
tines to a neutral position.
Belt Tension Adjustment
Proper belt tension is critical for good performance. After 30
minutes of operation, all cables may have to be adjusted due
to initial stretch. Thereafter, check tension after every two
hours of operation.
FIGURE 10
1. To increase belt tension, loosen upper jam nut in 1/8"
increments while holding lower jam nut in place.
SEE FIGURE 11
2. Check adjustment and instructions under “Check Belt
Tension” section.
This procedure can be repeated until conduit adjustment
bolts have no more adjustment left. If no more adjustment
can be made, belt may have to be replaced.
Depth Regulator Drag Stake
To Adjust Tilling Depth:
1. Remove lock pin.
2. Raise or lower the depth regulator. The lower the depth
regulator, the deeper the tilling depth.
3. Align hole in depth regulator lever with hole in depth
regulator bracket and replace lock pin.
SEE FIGURE 9 (page 11)
UPPER
JAM
NUT
LOWER
JAM
NUT
FIGURE 11FIGURE 11
WARNING
THIS INFORMATION IS PROVIDED HERE ONLY TO
INTRODUCE THE CONTROLS. DO NOT START THE
ENGINE AT THIS TIME. STARTING AND OPERATING
INSTRUCTIONS ARE GIVEN IN THIS MANUAL. PLEASE
READ THIS SECTION AND ALL OPERATING AND
SAFETY INSTRUCTIONS BEFORE STARTING YOUR
TILLER.
AS A SAFETY PRECAUTION, THE DRIVE SAFETY
CONTROL LEVER WILL NOT LOCK IN THE FORWARD
POSITION.
TO STOP THE TINES AT ANY TIME, RELEASE THE
DRIVE SAFETY CONTROL LEVER.
ENGINE SHOULD BE OFF BEFORE ADJUSTING ANY
CONTROLS.
DO NOT ADJUST TILLING DEPTH UNLESS DRIVE
SAFETY CONTROL LEVER IS RELEASED TO THE
NEUTRAL POSITION.
WARNING
THE RIGHT AND LEFT SIDES
OF YOUR ROTOTILLER ARE
DETERMINED FROM THE
OPERATING POSITION AS
YOU FACE THE DIRECTION
OF FORWARD TRAVEL.
ENGINE IS SHIPPED FROM FACTORY WITHOUT OIL.
YOU MUST ADD ENGINE OIL BEFORE STARTING
ENGINE.
L R
Operator’s Manual
BADGER Front Tine Tiller
13For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST
DANGER
DO NOT START YOUR TILLER UNTIL YOU HAVE
READ AND UNDERSTAND THIS MANUAL AND THE
SECTIONS IN THIS MANUAL COVERING SAFETY AND
OPERATION.
ALWAYS PERFORM THE PRESTART INSPECTION
CHECKLIST BEFORE STARTING THE ENGINE.
PRACTICE OPERATING THE CONTROLS AND TILLER
WITH TINES OUT OF GROUND BEFORE BEGINNING
TO TILL. IT IS IMPORTANT THAT YOU KNOW HOW TO
USE THE TILLER PROPERLY: KEEP CONTROL AT ALL
TIMES, STOP THE TINE FROM TURNING, AND STOP
THE ENGINE IF NECESSARY. IF YOU DO NOT KNOW
HOW TO DO THESE THINGS, READ THE CONTROLS
AND SAFETY SECTIONS BEFORE PROCEEDING.
ALWAYS MAINTAIN CONTROL OF YOUR TILLER. ONLY
OPERATE TILLER IN SOIL CONDITIONS THAT ARE
CONDUCIVE TO MAINTAINING CONTROL OF THE
TILLER. DO NOT OPERATE TILLER IN CONDITIONS THAT
CONTAIN ROCKS, FOREIGN OBJECTS, OR ANY OTHER
MATERIAL THAT IS NOT SOIL. IF YOUR TILLER BUMPS,
JERKS, OR LURCHES, LET GO OF THE HANDLEBARS
AND THE DRIVE CONTROL LEVER IMMEDIATELY SO
THAT THE TINES STOP TURNING.
CAUTION MUST BE TAKEN WHEN SELECTING TILLING
DEPTH. LOSS OF CONTROL COULD RESULT IF YOU
ATTEMPT TO TILL IN CERTAIN SOIL CONDITIONS WITH
THE DRAG STAKE SET IN TOO HIGH OF A POSITION.
STOP THE ENGINE AND REMOVE SPARK PLUG WIRE
BEFORE REMOVING MATERIAL FROM THE TINES BY
HAND OR ANY OTHER METHOD.
ENGINE AND SURROUNDING PARTS BECOME
EXTREMELY HOT DURING NORMAL OPERATION.
TEMPERATURE OF MUFFLER AND NEARBY AREAS
MAY EXCEED 150°F 66°C. AVOID THESE AREAS.
ALLOW ENGINE TO COOL COMPLETELY BEFORE
TOUCHING THESE HOT SURFACES. THESE AREAS WILL
CAUSE SERIOUS BURN INJURIES IF TOUCHED BEFORE
THE ENGINE HAS COOLED.
ALWAYS KEEP HANDS AND FEET CLEAR OF ROTATING
MACHINE PARTS.
CAUTION
DO NOT USE CHOKE CONTROL TO STOP ENGINE.
BACKFIRE OR ENGINE DAMAGE MAY OCCUR!
TO STOP THE ENGINE AT ANY TIME, MOVE THROTTLE
CONTROL TO THE OFF OR STOP POSITION, OR TURN
THE ON/OFF SWITCH TO OFF.
ALWAYS RELEASE DRIVE SAFETY CONTROL LEVER TO
NEUTRAL POSITION BEFORE ADJUSTING THE DEPTH
OF THE DRAG STAKE.
ENGINE IS SHIPPED FROM FACTORY WITHOUT OIL.
YOU MUST ADD ENGINE OIL BEFORE STARTING
ENGINE.
Operator’s Manual
BADGER Front Tine Tiller
14 For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST
Cold Start
1. Push ON/OFF switch to the ON position.
2. Move choke lever to full choke position, if equipped.
3. Pull starting rope out slowly one time and allow to return
normally.
4. Pull starting rope out rapidly and allow rope to return normally.
5. When engine starts, gradually move choke lever to no
choke position, if equipped.
NOTE: The engine installed on the tiller is xed speed
and does not have a throttle control.
Restarting A Warm Engine
Restarting an engine that is already warm from previous run-
ning does not normally require the use of the choke, if one is
equipped.
1. Push ON/OFF switch to the ON position.
2. Pull starting rope out rapidly until engine starts. Allow rope
to return normally. Repeat until engine starts.
Shutting Down
To stop the engine at any time, put the ON/OFF switch to the
OFF position. To stop tines at any time, release the drive safety
control to the neutral position.
Tilling
1. Adjust the depth regulator drag stake to achieve desired
tilling depth.
NOTE: Raise depth regulator lever up one hole at a
time, testing tiller operation after each adjustment.
Raising depth regulator lever too high can result in loss
of control of tiller!
2. Place the tiller in motion by pushing down on the drive
safety control lever; this will engage the tines.
OPERATION
Pre-Start Inspection
1. Make sure all safety guards are in place and all nuts and
bolts are secure.
NOTE: All hardware (nuts, bolts, etc) should be checked
for tightness before each use. Vibration of machine
can cause them to loosen.
2. Check oil level in engine crankcase. See your engine
manual for procedure and specications.
3. Inspect air cleaner for cleanliness. See your engine manual
for procedure.
4. Check the fuel level. Fill the fuel tank no closer than one
inch from top of tank to provide space for expansion. See
your engine manual for fuel recommendations.
5. Be sure spark plug wire is attached and spark plug is
tightened securely.
6. Check position of wheels.
7. Check depth regulator drag stake position.
8. Examine underneath and around engine for signs of oil or
fuel leaks.
9. Inspect fuel hoses for tightness and fuel seepage.
10. Look for signs of engine damage.
11. Remove excessive debris from muer area and recoil
starter.
12. Turn fuel shuto valve to the ON position if engine is
equipped with one.
STARTUP
The ON/OFF switch and choke lever required to cold start
the rototiller are located on the engine and are marked with
ON/OFF and choke control symbols (See Operation Control
Symbols in the Controls and Operating Symbols section of this
manual). SEE FIGURE 12
A description of engine operation and all related precautions
and procedures can be found in the engine manufacturer’s
manual that accompanies the tiller.
WARNING
GASOLINE IS HIGHLY FLAMMABLE AND MUST BE
HANDLED WITH CARE. NEVER FILL THE TANK WHEN
THE ENGINE IS HOT OR RUNNING. ALWAYS MOVE
OUTDOORS TO FILL THE TANK.
ON/OFF
Switch
Choke
Lever
FIGURE 12FIGURE 12
Operator’s Manual
BADGER Front Tine Tiller
15For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST
MAINTENANCE
Maintenance Schedule
Your rototiller has been designed and produced by the industrys leading manufacturer of outdoor power equipment to provide
you with years of reliable operation. Keeping your tiller in top running condition will prolong its life, and help you obtain optimum
performance. Please read this maintenance schedule, and note the recommended care operating intervals to extend the life of
your unit.
Maintenance Operation Page
Before
Each Use
50 hours or
Every Season
Check belt tension 16 X
Change forward belt 16 X
Engine maintenance 17, EM X X
Check oil level/change oil 17, EM X 1
Clean tine axle shaft 17 X X
Lubrication 17 X
EM = See engine manual
1 = Change oil after the rst three to ve hours of use, then after every 50 hours or every season. Change oil
every 25 hours when operating under heavy load or in high temperatures.
SERVICING THE ROTOTILLER
The following information will help you make the necessary
checks and perform the procedures required to follow the
normal care recommendations made for your rototiller unit.
If you prefer, your local authorized dealer can make these
checks and perform the required procedures for you.
Important: Use only approved Earthquake® spare parts.
Spark
Plug
Wire
WARNING
PREVENT ACCIDENTAL STARTING.
ENGINE MUST BE TURNED OFF AND COOL, AND SPARK
PLUG WIRE MUST BE REMOVED AND SECURED FROM
SPARK PLUG BEFORE CHECKING AND ADJUSTING
ENGINE OR EQUIPMENT. ACCIDENTAL ENGINE START
CAN CAUSE SERIOUS INJURY.
Operator’s Manual
BADGER Front Tine Tiller
16 For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST
BELT MAINTENANCE
Check Belt Tension
Belt tension may decrease over time. It may need to be
adjusted within the rst half hour of operation and should be
checked after every two hours of operation. Proper adjustment
will assure long belt life. Too much or too little belt tension will
cause premature belt failure.
An indication that the belt may need to be adjusted is
a constant buzzing sound that can be heard when the
engagement lever is compressed (see page 18), or a persistant
squealing sound when engaged and under load.
NOTE: A short buzzing noise can be heard when
engagement lever is released. This is normal, caused
by the teeth of the cog belt catching the wire guide,
stopping the rotation of the belt. This does not require
the belt tension to be adjusted.
To check and adjust the belt tension, do as follows:
1. Turn o engine. Engine must be cool.
2. Remove spark plug wire from spark plug and secure.
3. With drive safety control lever in the neutral position,
measure length of the cable spring when in its relaxed
state.
4. Pull down on drive safety control lever and measure length
of spring when extended. Ideal length would be 1/4"
longer. SEE FIGURE 13
5. To adjust, SEE FIGURE 11 and Belt Tension Adjustment
instructions.
Change Belt
1. Turn o engine. Engine must be cool.
2. Remove spark plug wire from spark plug and secure.
3. Remove front belt cover and dirt shield plate from tiller
frame. SEE FIGURE 14
a. Remove the belt from the engine pulley as follows:
Gently pull the engine recoil rope to rotate the pulley.
With the pulley turning, force the belt out of the
V-groove.
Slide the belt free of the engine pulley.
Pull the belt down and out of the way.
Push the belt forward and out the front of the machine.
b. Install new belt as follows:
Place belt in transmission pulley groove.
Gently pull the engine recoil rope to rotate the engine
pulley while forcing the belt into the V-groove.
4. Reinstall front belt cover and dirt shield plate onto tiller frame.
5. Check and readjust belt tension if necessary.
6. Attach spark plug wire.
BELT REPLACEMENT P/N: 22633
Front
Belt
Cover
Dirt Shield Plate
FIGURE 14
FIGURE 13
ÉTIREMENT DE
6 MM (1/4 PO)
IMPORTANT
CHECK BELT TENSION REGULARLY. TOO MUCH OR
TOO LITTLE TENSION WILL CAUSE PREMATURE BELT
FAILURE AND DAMAGE TO EQUIPMENT.
Operator’s Manual
BADGER Front Tine Tiller
17For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST
ENGINE MAINTENANCE
Refer to the engine manual included in your parts bag for
information on engine maintenance. Your engine manual pro-
vides information and a maintenance schedule for performing
the following tasks:
1. Check oil level before each use and after every eight hours
of operation.
2. Change oil after rst three to ve hours of operation.
3. Change oil while engine is warm. Rell with new oil of
recommended grade.
4. Check spark plug yearly or every 100 hours of operation.
5. Service air cleaner.
6. Keep engine and parts clean.
7. Check engine and equipment often for loose nuts and
bolts; keep all hardware tightened.
Check or Fill Engine Crankcase
1. Add oil according to engine manual. Do not overll. Use
a clean, high-quality 4-cycle engine oil. Use no special
additives with recommended oils. Do not mix oil with
gasoline. Oil level must be full. Check the oil level by
checking the engine’s oil dipstick.
2. Always check oil level before starting engine. Refer to
engine manual for capacity and type of oil to use.
Clean Tine Axle Shaft
1. Turn o engine. Engine must be cool.
2. Remove spark plug wire and secure from spark plug.
3. Remove all vegetation, string, wire, and other material that
may have accumulated on the axle between the inside set
of tines and the seal on the transmission housing.
4. Replace spark plug wire.
Lubrication
Proper lubrication of moving mechanical parts is critical for
proper care and maintenance. Oil the moving parts using a
30-weight oil.
STORAGE
Prepare for Storage
Follow the steps below to prepare your tiller for storage. Read
your engine manual for detailed instructions on preparing the
engine for storage.
1. Protect wheels and axles from rust:
Coat the axles lightly with axle grease.
2. Drain fuel system completely following engine manufacturer’s
instructions or add fuel stabilizer to prevent fuel from
gumming up during extended storage period. Run engine
for at least 5 minutes to distribute fuel stabilizer mixture
throughout entire fuel system.
3. While engine is still warm, drain the oil from the engine. Rell
with fresh oil that is recommended in engine manual.
4. Clean external surfaces, engine and cooling fan.
5. Remove spark plug; pour one ounce of SAE 30 oil into spark
plug hole.
6. Plug hole and pull starter cord slowly to distribute oil evenly
in cylinder head area.
7. Reinstall spark plug.
8. Transport unit to a suitable storage location. If you have
chosen to use a fuel stabilizer and have not drained the fuel
system, follow all safety instructions and storage precautions
in this manual to prevent the possibility of re from the
ignition of gasoline fumes. Remember, gasoline fumes can
travel to distant sources of ignition and ignite, causing risk
of explosion and re.
9. If there is any possibility of unauthorized use or tampering,
remove the spark plug and store it in a safe place before
storing the rototiller unit. Be sure to plug the spark plug hole
to prevent foreign material from entering.
WARNING
PRACTICE SAFETY AT ALL TIMES. ENGINE MUST BE
TURNED OFF AND ALLOWED TO COOL, AND SPARK
PLUG WIRE MUST BE DISCONNECTED AND SECURED
BEFORE ATTEMPTING ANY MAINTENANCE OR REPAIR.
FAILURE TO COMPLY WITH THIS SAFETY REQUIREMENT
CAN RESULT IN SERIOUS PERSONAL INJURY TO YOU
OR BYSTANDERS.
DO NOT STORE TILLER IN AN UNVENTILATED AREA
WHERE FUEL FUMES MAY REACH FLAME, SPARKS,
PILOT LIGHTS OR AN IGNITED OBJECT. DRAIN FUEL
OUTDOORS AWAY FROM ANY IGNITION SOURCES.
USE ONLY APPROVED FUEL CONTAINERS.
CAUTION
ENGINE IS SHIPPED FROM FACTORY WITHOUT OIL. YOU
MUST ADD ENGINE OIL BEFORE STARTING ENGINE.
ENGINE CAN OVERHEAT AND BECOME DAMAGED IF
DEBRIS BLOCKS THE COOLING SYSTEM OR ROTATING
SCREEN.
NEVER RUN ENGINE WITHOUT COMPLETE AIR CLEANER
INSTALLED ON ENGINE.
FAILURE TO FOLLOW THESE INSTRUCTIONS CAN CAUSE
DAMAGE TO THE ENGINE AND VOID YOUR WARRANTY.
Operator’s Manual
BADGER Front Tine Tiller
18 For additional information visit online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST
PROBLEM REMEDY/ACTION
Engine will not start Add gas to gas tank.
Connect spark plug wire to spark plug.
ON/OFF switch must be turned ON and engine choked
for a cold start (if equipped with a choke).
Engine runs rough, oods during operation Clean or replace air cleaner.
Engine is hard to start Drain old fuel and replace with fresh. Use gas stabilizer
at end of season.
Make sure spark plug wire is securely attached to spark
plug.
Drive safety control lever must be released to neutral to
start the engine.
Engine misses or lacks power Raise the tines for shallow tilling by raising the depth
regulator drag stake.
Clean or replace air cleaner.
Improper carburetor adjustment, take to authorized
engine service center.
Replace spark plug and adjust gap.
Drain and rell gas tank with fresh fuel.
Tiller moves forward during starting Drive safety control lever must be released to neutral to
start the engine.
Check belt tension.
Tiller is dicult to control when tilling
(Machine jumps or lurches forward)
Lower the depth regulator drag stake for greater
resistance and control of the machine.
Belts squeal in forward operation Check belt tension and adjust if necessary.
Constant buzzing sound is heard while engagement lever is com-
pressed
Fully compress engagement lever
Properly space wire guide from idler pulley to clear belt
Check belt tension and adjust if necessary.
NOTE: If engagement lever is fully compressed, wire
guide is properly adjusted, and cable has reached
full adjustment and buzzing persists, the belt may be
stretched and may need to be replaced. *
Excessive heat build up in transmission/tine area during tilling Remove vegetation.
Check transmission uid and ll if needed.
TROUBLESHOOTING AND REPAIR
Troubleshooting Guide
While normal care and routine maintenance will extend the life of your rototiller, prolonged or constant use may eventually
require that service be performed to allow it to continue operating properly. The troubleshooting guide below lists the most
common problems, causes and remedies.
* Please contact 800-345-6007 for service parts
Manuel de l’utilisateur
Motoculteur à dents avant BADGER
19Pour plus de renseignements, visiter notre site Web à www.getearthquake.com ou composer le 800-345-6007 L-V 8h-17h HNC
INTRODUCTION
Merci d’avoir acheté le motoculteur BADGER d’Earthquake®. Nous nous sommes attachés à ce que ce motoculteur réponde aux plus hautes
normes d’utilisation et de durabilité. Moyennant des soins corrects, il orira de nombreuses années de service able.
Lire ce manuel en entier avant de l’installer et de l’utiliser. Earthquake® se réserve le droit de changer, modier ou améliorer ce produit
et cette documentation à tout moment sans préavis.
SOMMAIRE
Introduction / Sommaire / Enregistrement et service après-vente .....................................................................................................................................................19
Avertissements et mesures de précaution ..............................................................................................................................................................................................20-23
Autocollants de sécurité ...................................................................................................................................................................................................................................... 24
Symboles de sécurité et signications ...........................................................................................................................................................................................................25
Caractéristiques ......................................................................................................................................................................................................................................................26
Déballage et assemblage ..............................................................................................................................................................................................................................27-29
Symboles de commande et de fonctionnement / Commandes ..................................................................................................................................................... 29-30
Utilisation .................................................................................................................................................................................................................................................................. 31
Entretien ..............................................................................................................................................................................................................................................................32-34
Entreposage .............................................................................................................................................................................................................................................................34
Dépannage et réparation .................................................................................................................................................................................................................................... 35
RENSEIGNEMENTS SUR LE PROPRIÉTAIRE
Nom du propriétaire:
Adresse du propriétaire:
Ville : État/Province: Code postal:
Numéro de modèle: Numéro de série:
Date d’achat:
Notes:
Consigner le numéro de modèle et le numéro de série du produit dans
l’espace prévu pour y accéder facilement lors des commandes de pièces
détachées ou des demandes d’assistance technique. À l’exception des
articles couverts par la garantie sur le contrôle des émissions, la garantie
est valable uniquement si l’enregistrement dûment rempli est reçu par
Ardisam dans les 30 jours après l’achat. (POUR PLUS DE RENSEIGNEMENTS,
VOIR LA SECTION SUR LA GARANTIE.) Lenregistrement de la garantie peut
se faire en ligne à www.getearthquake.com ou par courrier à: Ardisam,
1160 8th Avenue, Cumberland, WI 54829, États-Unis. Il est aussi possible
d’appeler notre Service après-vente au (800) 345-6007 du lundi au
vendredi de 8h00 à 17h00 HNC.
Lire ce manuel et le conserver pour toute consultation ultérieure. Ce manuel contient des renseignements importants sur la SÉCURITÉ,
l’ASSEMBLAGE, l’UTILISATION et l’ENTRETIEN. Le propriétaire doit veiller à ce que toute la documentation sur le produit soit fournie
avec l’appareil. Cette documentation comprend le MANUEL, la liste des PIÈCES DE RECHANGE et les GARANTIES. Cette documentation
doit être fournie en vertu de la réglementation en vigueur. Toutes les personnes à qui cette machine est louée/prêtée doivent avoir
accès à ces informations et les comprendre. Le présent manuel doit rester avec le produit, notamment sil est revendu.
Enregistrement et service après-vente
Autocollant
de numéro
de série
Manuel de l’utilisateur
Motoculteur à dents avant BADGER
20 Pour plus de renseignements, visiter notre site Web à www.getearthquake.com ou composer le 800-345-6007 L-V 8h-17h HNC
AVERTISSEMENTS ET MESURES DE
PRÉCAUTION
Responsabilité du propriétaire
L’assemblage correct et l’utilisation sûre et ecace de la machine
relèvent de la responsabilité de l’utilisateur.
Lire et respecter toutes les instructions de sécurité.
Suivre avec attention toutes les instructions d’assemblage.
Entretenir la machine conformément aux instructions et au
calendrier gurant dans le manuel de l’utilisateur Earthquake.
S’assurer que quiconque utilise la machine est bien familiarisé
avec toutes les commandes et mesures de précaution.
Messages spéciaux
Ce manuel contient des messages spéciaux attirant l’attention sur des
problèmes de sécurité et dommages potentiels à la machine, ainsi
que des informations utiles sur l’utilisation et l’entretien. Veiller à lire
toutes ces informations avec attention pour éviter les blessures et les
dommages à la machine.
REMARQUE: Des informations générales sont fournies à
travers ce manuel pouvant aider l’opérateur dans
l’utilisation ou l’entretien de la machine.
CE SYMBOLE SIGNALE DES INSTRUCTIONS DE
SÉCURITÉ IMPORTANTES QUI DOIVENT ÊTRE
RESPECTÉES POUR NE PAS METTRE EN DANGER
LA SÉCURITÉ DES PERSONNES. LIRE ET RESPECTER
TOUTES LES INSTRUCTIONS DU MANUEL
AVANT DE TENTER DE FAIRE FONCTIONNER CET
APPAREIL.
Avant d’utiliser la machine:
Veiller à lire cette section avec attention. Lire l’ensemble
des instructions d’utilisation et d’entretien de ce produit. Tout
manquement à respecter ces instructions peut entraîner des
blessures graves ou la mort. Utiliser la machine conformément
aux instructions de sécurité fournies ici et tout au long du manuel.
Quiconque utilise cette machine doit lire les instructions et être
familiarisé avec les commandes.
Emploi prévu / Emploi détourné prévisible
IMPORTANT: Ceci est un motoculteur rotatif motorisé qui travaille le
sol au moyen de fraises en rotation. Il est conçu pour un utilisateur à
pied, mais nest pas autotracté, avec un moteur à combustion interne
à essence pour entraîner les fraises. Il ne doit être utilisé à aucune
autre n.
DANGER
SRT CRT
AVERTISSEMENT
AVERTISSEMENT INDIQUE UN DANGER QUI, S’IL N’EST PAS
ÉVITÉ, PEUT PROVOQUER LA MORT OU DES BLESSURES
CORPORELLES ET/OU DÉGÂTS MATÉRIELS GRAVES.
ATTENTION
ATTENTION INDIQUE UN DANGER QUI, S’IL N’EST PAS
ÉVITÉ, PEUT PROVOQUER DES BLESSURES CORPORELLES
ET/OU DES DÉGÂTS MATÉRIELS.
DANGER
DANGER INDIQUE UN DANGER QUI, S’IL N’EST PAS ÉVITÉ,
PROVOQUERA IMMANQUABLEMENT LA MORT OU DES
BLESSURES CORPORELLES ET/OU DÉGÂTS MATÉRIELS
GRAVES.
AVERTISSEMENT
VEILLER À LIRE, À COMPRENDRE ET À RESPECTER TOUTES
LES INSTRUCTIONS DE SÉCURITÉ ET D’UTILISATION
FIGURANT DANS CE MANUEL AVANT DE TENTER
D’INSTALLER ET DE FAIRE FONCTIONNER VOTRE MACHINE.
TOUT MANQUEMENT À OBSERVER LES INSTRUCTIONS
DE SÉCURITÉ ET D’UTILISATION PEUT PROVOQUER DES
BLESSURES CORPORELLES GRAVES POUR L’UTILISATEUR
ET D’AUTRES PERSONNES PRÉSENTES ET DES DÉGÂTS
MATÉRIELS. LE TRIANGLE DANS LE TEXTE SIGNIFIE QUE
DES MISES EN GARDES ET AVERTISSEMENT IMPORTANTS
DOIVENT ÊTRE SUIVIS.
AVERTISSEMENT
AVERTISSEMENT PROPOSITION 65 DE CALIFORNIE
L’ÉCHAPPEMENT DU MOTEUR DE CE PRODUIT CONTIENT
DES SUBSTANCES CHIMIQUES DÉCLARÉES RESPONSABLES
DE CANCER, MALFORMATIONS CONGÉNITALES OU
AUTRES ANOMALIES DE LA REPRODUCTION PAR L’ÉTAT DE
CALIFORNIE.
IMPORTANT
IMPORTANT SIGNALE DES INFORMATIONS UTILES
CONCERNANT LASSEMBLAGE, L’UTILISATION OU
L’ENTRETIEN DU MATÉRIEL.
AVIS
AVIS INDIQUE QUE LE MATÉRIEL PEUT ÊTRE ENDOMMA
SI LES INSTRUCTIONS DE SÉCURITÉ QUI SUIVENT CE MOT
INDICATEUR NE SONT PAS RESPECTÉES.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

EarthQuake 31043 Le manuel du propriétaire

Catégorie
Mini motoculteurs
Taper
Le manuel du propriétaire
Ce manuel convient également à

dans d''autres langues