Datalogic JOYA Touch 22 Multi Purpose Device for Retail Manuel utilisateur

Datalogic
Marque
Datalogic
Modèle
JOYA Touch 22 Multi Purpose Device for Retail
Taper
Manuel utilisateur
Datalogic S.r.l.
Via San Vitalino 13
40012 Calderara di Reno (BO)
Italy
Tel. +39 051 3147011
Fax +39 051 3147205
©2022 Datalogic S.p.A. and/or its affiliates
All rights reserved. Without limiting the rights under copyright, no part of this documentation may be repro-
duced, stored in or introduced into a retrieval system, or transmitted in any form or by any means, or for any
purpose, without the express written permission of Datalogic S.p.A. and/or its affiliates.
Owners of Datalogic products are hereby granted a non-exclusive, revocable license to reproduce and tran-
smit this documentation for the purchaser's own internal business purposes. Purchaser shall not remove or
alter any proprietary notices, including copyright notices, contained in this documentation and shall ensure
that all notices appear on any reproductions of the documentation.
Electronic versions of this document may be downloaded from the Datalogic website (www.datalogic.com).
If you visit our website and would like to make comments or suggestions about this or other Datalogic publi-
cations, please let us know via the "Contact" page.
Disclaimer
Datalogic has taken reasonable measures to provide information in this manual that is complete and accu-
rate, however, Datalogic shall not be liable for technical or editorial errors or omissions contained herein, nor
for incidental or consequential damages resulting from the use of this material. Datalogic reserves the right
to change any specification at any time without prior notice.
Trademarks
Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries, including
the U.S.A. and the E.U.
The Joya logo is a trademark of Datalogic S.p.A. and/or its affiliates, registered in the U.S. and the E.U. All
other trademarks and brands are property of their respective owners.
Patents
See www.patents.datalogic.com for patent list.
This product is covered by one or more of the following patents:
Design patents: EP002703025, EP002805218, ZL201530463613.4
Utility patents: EP0789315B1, EP0895175B1, EP0996284B1, EP0999514B1, EP1114390B1, EP1128315B1,
EP1172756B1, EP1396811B1, EP1413971B1, EP1804089B1, EP1828957B1, EP2275966B1, EP2315156B1,
EP2517148B1, EP2649555B1, JP4435343B2, JP5192390B2, US5992740, US6305606, US6478224,
US6512218, US6513714, US6561427, US6808114, US6877664, US6997385, US7053954, US7234641,
US7387246, US7620475, US8113430, US8245926, US8888003, US8915443, ZL200680050007.8,
ZL200980163411.X.
NOTE: Read carefully the JOYA TOUCH 22 User Manual (available at www.datalogic.
com) before performing any type of connection to the JOYA TOUCH 22.
The user is responsible for any damage caused by incorrect use of the equipment or
by inobservance of the indication supplied in the user manual.
CLEANING INSTRUCTIONS
Periodically clean the JOYA TOUCH 22 device using a so cloth slightly dampened with only water
or Isopropyl Alcohol (70%).
Do not use any other cleaning agents (e.g. different alcohol, abrasive or corrosive products, sol-
vents) or abrasive pads to clean the device.
Do not spray or pour liquids directly onto the device. The device is not water resistant. Keep it dry.
JOYA™ TOUCH 22
SAFETY & REGULATORY
ADDENDUM
Multi-Purpose Device for
Retail
• All rights reserved • Without limiting
the rights under copyright, no part of this
documentation may be reproduced, stored
in or introduced into a retrieval system, or
transmitted in any form or by any means,
or for any purpose, without the express
written permission of Datalogic S.p.A.
and/or its affiliates • Datalogic and the
Datalogic logo are registered trademarks
of Datalogic S.p.A. in many countries,
including the U.S. and the E.U.
This document is an addendum to the
Quick Start Guide (QSG) for this product.
See the QSG for additional product
information.
www.datalogic.com
©2022 Datalogic S.p.A. and/or its affiliates
GENERAL SAFETY RULES
CAUTION:
• Before using the devices and the battery packs, read
this Addendum carefully.
• Use only the components and accessories supplied
by the manufacturer for the specific JOYA TOUCH 22
being used.
• Do not attempt to disassemble the JOYA TOUCH
22 device, as it does not contain parts that can be
repaired by the user. Any tampering will invalidate the
warranty.
• When replacing the battery pack or at the end of the
operative life of the JOYA TOUCH 22 device, disposal
must be performed in compliance with the laws in
force in your jurisdiction.
• Do not submerge the JOYA TOUCH 22 in liquid
products.
• For further information or support, refer to the
Datalogic web site: www.datalogic.com.
CAUTION:
Do not apply any sticker to the JOYA TOUCH 22.
POWER SUPPLY
The device is intended to be supplied by a self-contained rechargeable
Lithium Ion battery pack (UL listed LPS/SELV power source) and/or by
UL Listed/CSA Certified Power Unit LPS/SELV power source which sup-
plies power directly to the unit via the USB-C connector of the cable.
The device could be also used with Certified Accessories (Dock/Cradle)
which supply Wireless power. The Dock/Cradle accessories are inten-
ded to be supplied by a UL Listed/CSA Certified Power Unit LPS/SELV
rating 12V, min 5A power source which supplies power via the power
connector of the cable.
Any changes or modifications to equipment, not expressly approved by
Datalogic could void the user’s authority to operate the equipment.
BATTERY INFORMATION
CAUTION: Do not incinerate, disassemble, short
terminals, or expose to high temperature. Risk of fire and
explosion. Use specified charger only. Risk of explosion if
the battery is replaced by an incorrect
type. Dispose of batteries as required by local authorities.
By default, the main battery pack is disconnected at the factory to avoid
damage due to excessive draining.
Rechargeable battery pack is less than half of full charge when delive-
red. Charge the battery pack as indicated in the Quick Start Guide or in
the User Manual, before using the JOYA TOUCH 22 device.
The battery pack autonomy varies according to many factors, such as
the frequency of barcode scanning, RF usage, battery life, storage, envi-
ronmental conditions, etc.
Close to the limits of the working temperature, some battery perfor-
mance degradation may occur.
The JOYA TOUCH 22 should be charged at an ambient temperature
between 0 - 35º C (32 to 95ºF) to achieve the maximum charging rate.
Never charge the device battery in a closed space where excessive heat
can build up.
As a safety precaution, the battery may stop charging to avoid
overheating.
The JOYA TOUCH 22 gets warm during charging; this is normal and
does not mean a malfunction.
Even if the storage temperature range is wider, it is recommended to
store the terminal and the batteries at environmental temperature, in
order to achieve the longest battery life.
CAUTION: Avoid storing batteries for long periods in a
state of full charge or very low charge.
We recommend charging the battery pack every two to
three months to keep its charge at a moderate level to
maximize battery life.
Annual replacement of rechargeable battery pack
avoids possible risks or abnormalities and ensures
maximum performance.
WARNING: Use only Datalogic approved batteries and
accessories for battery charging.
Risk of explosion if battery is replaced by an incorrect
type.
Dispose of used batteries according to the instructions.
Il y a risque d’explosion si la batterie est remplacée par
une batterie de type incorrect.
Mettre au rebut les batteris usagées confor mément
aux instructions.
CAUTION: Do not put any foreign object such as, but not
limited to, coins, paper clips, stickers inside the slot of
any of the docks (see the examples below).
BATTERY SAFETY GUIDELINES
WARNING: Installing, charging and/or any other action
should be done by authorized personnel and following
this manual.
The battery pack may get hot, explode, ignite, and/or
cause serious injury if exposed to abusive conditions.
If the battery pack is replaced with an improper type,
there is risk of explosion.
Do not place the battery pack in or near a fire or
other heat source; do not place the battery pack in
direct sunlight, or use or store the battery pack inside
unventilated areas in hot weather; do not place the
battery pack in microwave ovens, in clothes dryers, in
high pressure containers, on induction cook surfaces or
similar devices. Doing so may cause the battery pack
to generate heat, explode or ignite. Using the battery
pack in this manner may also result in a loss of
performance and a shortened life expectancy.
To power the cradle, use only a Datalogic approved
power supply. The use of an alternative power supply
will void the product warranty, may cause product
damage and may cause heat, an explosion, or fire.
The area in which the units are charged should be clear
of debris and combustible materials or chemicals.
Do not use the battery pack of this terminal to power
devices other than this device.
Immediately discontinue use of the battery pack if,
while using, charging or storing the battery pack, the
battery pack emits an unusual smell, feels hot, changes
colour or shape, or appears abnormal in any other way.
852002141 (Rev. B) October 2022
WARNING: Do not short-circuit the battery pack contacts connecting the positive
terminal and negative terminal. This might happen, for example, when you carry
a spare battery pack in your pocket or purse; accidental short–circuiting can occur
when a metallic object such as a coin, clip, or pen causes direct connection of the
contacts of the battery pack (these look like metal strips on the battery pack). Short–
circuiting the terminals may damage the battery pack or the connecting object.
Do not apply voltages to the battery pack contacts.
Do not pierce the battery pack with nails, strike it with a hammer, step on it or
otherwise subject it to strong impacts, pressures, or shocks.
Do not disassemble or modify (i.e. bend, crush or deform) the battery pack. The
battery pack contains safety and protection devices, which, if damaged, may cause
the battery pack to generate heat, explode or ignite.
In case of leakage of liquid from the battery, avoid contact with liquid the skin or
eyes. If the contact occurs, immediately wash the affected area with water and
consult a doctor.
Do not solder directly onto the battery pack.
Do not expose the battery pack to liquids.
Avoid any knocks or excessive vibrations. If the device or the battery is dropped,
especially on a hard surface, you should take it to the nearest Authorised Repair
Centre for inspection before continuing to use it.
If your device stops working for any reason, do not use its battery on other electronic
devices without a prior check and approval by an Authorised Repair Centre.
Do not replace the battery pack when the device is turned on.
Do not remove or damage the battery pack’s label.
Do not use the battery pack if it is damaged in any part.
Battery pack usage by children should be supervised.
WIRELESS AND RADIO FREQUENCIES WARNINGS
WARNING: Use only the supplied or an approved replacement antenna. Unauthorized
antennas, modifications or attachments could damage the product and may violate
laws and regulations.
Most modern electronic equipment is shielded from RF signals. However, certain
electronic equipment may not be shielded against the RF signals generated by JOYA
TOUCH 22.
Datalogic recommends persons with pacemakers or other medical devices to follow
the same recommendations provided by Health Industry Manufacturers Associations
for mobile phones.
Persons with pacemakers:
• Should ALWAYS keep this device more than twenty five (25) cm from their
pacemaker and/or any other medical device;
• Should not carry this device in a breast pocket;
• Should keep the device at the opposite side of the pacemaker and/or any other
medical device;
• Should turn this device OFF or move it immediately AWAY if there is any reason
to suspect that interference is taking place.
• Should ALWAYS read pacemaker or any other medical device guides or should
consult the manufacturer of the medical device to determine if it is adequately
shielded from external RF energy.
In case of doubt concerning the use of wireless devices with an implanted medical
device, contact your doctor.
Turn this device OFF in health care facilities when any regulations posted in these
areas instruct you to do so. Hospitals or health care facilities may use equipment
that could be sensitive to external RF energy.
RF signals may affect improperly installed or inadequately shielded electronic
systems in motor vehicles. Check with the manufacturer or its representative
regarding your vehicle. You should also consult the manufacturer of any equipment
that has been added to your vehicle.
An air bag inflates with great force. DO NOT place objects, including either installed
or portable wireless equipment, in the area over the air bag or in the air bag
deployment area. If a vehicle’s wireless equipment is improperly installed and the
air bag inflates, serious injury could result.
Turn off the device when in any area with a potentially explosive atmosphere.
Observe restrictions and follow closely any laws, regulations, warnings and best
practices on the use of radio equipment near fuel storage areas or fuel distribution
areas, chemical plants or where any operation involves use of explosive materials.
Do not store or carry flammable liquids, explosive gases or materials with the device
or its parts or accessories.
WARNING: Areas with a potentially explosive atmosphere are oen, but not always,
clearly marked or shown.
Sparks in such areas could cause an explosion or fire, resulting in injury or even
death.
LASER SAFETY
The following information applies to Laser Aiming System, used on JOYA TOUCH 22 imager. The
laser light is visible to the human eye and is emitted from the window indicated in the figure below.
LASER RADIATION - DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
MAX OUTPUT RADIATION 1 mW
COMPLIANT WITH EN 60825-1:2014
NOTE: The artwork below may be only a dra. Please refer to the label attached to
the product for information about certification marks.
ITALIANO
Le seguenti informazioni vengono fornite dietro direttive delle autorità internazionali e si riferi-
scono all’uso corretto del terminale.
NORMATIVE STANDARD PER LA SICUREZZA LASER
Questo prodotto risulta conforme alle normative vigenti sulla sicurezza laser alla data di produ-
zione: CDRH 21 CFR 1040 e EN 60825-1.
Non si rende mai necessario aprire l’apparecchio per motivi di installazione, utilizzo o manuten-
zione.
ATTENZIONE: Non tentare di accedere allo scomparto contenete i componenti ottici
o di farne la manutenzione.
L’apertura dello scomparto, o la manutenzione di qualsiasi parte ottica da parte di
personale non autorizzato, potrebbe violare le norme della sicurezza. Il sistema
ottico può essere riparato solamente alla fabbrica.
L’utilizzo di procedure o regolazioni differenti da quelle descritte nella
documentazione può provocare un’esposizione pericolosa a luce laser visibile.
L’uso di strumenti ottici assieme allo scanner può aumentare il pericolo di danno
agli occhi. Tali strumenti ottici includono cannocchiali, microscopi, occhiali e lenti
di ingrandimento.
Il prodotto utilizza un diodo laser a bassa potenza. Sebbene non siano noti danni riportati dall’oc-
chio umano in seguito ad una esposizione di breve durata, evitare di fissare il raggio laser così
come si eviterebbe qualsiasi altra sorgente di luminosità intensa, ad esempio il sole. Evitare inol-
tre di dirigere il raggio laser negli occhi di un osservatore, anche attraverso superfici riflettenti
come gli specchi.
DEUTSCH
Die folgenden Informationen stimmen mit den Sicherheitshinweisen überein, die von internatio-
nalen Behörden auferlegt wurden, und sie beziehen sich auf den korrekten Gebrauch vom Termi-
nal.
NORM FÜR DIE LASERSICHERHEIT
Dies Produkt entspricht am Tag der Herstellung den gültigen EN 60825-1 und CDRH 21 CFR 1040
Normen für die Lasersicherheit.
Es ist nicht notwendig, das Gerät wegen Betrieb oder Installations- und Wartungs-Arbeiten zu
öffnen.
ACHTUNG: Unter keinen Umständen darf versucht werden, die Komponenten im
Optikhohlraum zu öffnen oder auf irgendwelche andere Weise zu warten. Das
Öffnen bzw. Warten der Komponenten im Optikhohlraum durch unbefugtes Personal
verstößt gegen die Laser-Sicherheitsbestimmungen. Das Optiksystem darf nur
werkseitig repariert werden.
Jegliche Änderungen am Gerät sowie Vorgehensweisen, die nicht in dieser
Betriebsanleitung beschrieben werden, können ein gefährliches Laserlicht
verursachen.
Die Verwendung von Optiksystemen mit diesem Scanner erhöht die Gefahr einer
Augenbeschädigung. Zu optischen Instrumenten gehören unter anderem Ferngläser,
Mikroskope, Brillen und Vergrößerungsgläser.
Der Produkt benutzt eine Laserdiode. Obwohl zur Zeit keine Augenschäden von kurzen Ein-
strahlungen bekannt sind, sollten Sie es vermeiden für längere Zeit in den Laserstrahl zu schauen,
genauso wenig wie in starke Lichtquellen (z.B. die Sonne). Vermeiden Sie es, den Laserstrahl
weder gegen die Augen eines Beobachters, noch gegen reflektierende Oberflächen zu richten.
FRANÇAIS
Les informations suivantes sont fournies selon les règles fixées par les autorités internationales
et se réfèrent à une correcte utilisation du terminal.
NORMES DE SECURITE LASER
Ce produit est conforme aux normes de sécurité laser en vigueur à sa date de fabrication: CDRH
21 CFR 1040 et EN 60825-1.
Il n’est pas nécessaire d’ouvrir l’appareil pour l’installation, l’utilisation ou l’entretien.
ATTENTION: Ne pas essayer d’ouvrir ou de réparer les composants de la cavité
optique. L’ouverture de la cavité optique ou la réparation de ses composants par une
personne non qualifiée peut entraîner le nonrespect des règles de sécurité relatives
au laser. Le système optique ne peut être réparé qu’en usine.
L’utilisation de procédures ou réglages différents de ceux donnés ici peut entraîner
une dangereuse exposition à lumière laser visible.
L’utilisation d’instruments optiques avec le scanneur augmente le danger pour les
yeux. Les instruments optiques comprennent les jumelles, les microscopes, les
lunettes et les verres grossissants.
Le produit utilise une diode laser. Aucun dommage aux yeux humains n’a été constaté à la suite
d’une exposition au rayon laser. Eviter de regarder fixement le rayon, comme toute autre source
lumineuse intense telle que le soleil. Eviter aussi de diriger le rayon vers les yeux d’un observa-
teur, même à travers des surfaces réfléchissantes (miroirs, par exemple).
Laser Warning Label
Data Label
Laser Aperture/Ouverture Laser
ITALIANO DEUTSCH FRANÇAIS ESPAÑOL
LA LUCE LASER È VISI-
BILE ALL’OCCHIO UMANO
E VIENE EMESSA DALLA
FINESTRA INDICATA
NELLA FIGURA.
DIE LASER-STRAHLUNG
IST FÜR DAS MEN-
SCHLICHE AUGE
SICHTBAR UND WIRD AM
STRAHLAUS TRITTSFEN-
STER AUSGESENDET
(SIEHE BILD).
LE RAYON LASER EST
VISIBLE À L’OEIL NU
ET IL EST ÉMIS PAR LA
FENÊTRE DÉSIGNÉE SUR
L’ILLUSTRATION DANS
LA FIGURE.
A LUZ LÁSER ES VISIBLE
AL OJO HUMANO Y ES
EMITIDA POR LA VEN-
TANA INDICADA EN LA
FIGURA.
LUCE LASER NON FIS-
SARE IL FASCIO
APPARECCHIO LASER
DI CLASSE 2 MASSIMA
POTENZA D’USCITA: 1
mW
LUNGHEZZA D’ONDA
EMESSA: 630~680 nm
CONFORME A EN
60825-1 (2007) e EN
60825-1 (2014).
LASERSTRAHLUNG
NICHT IN DEN STRAHL
BLICKEN PRODUKT
DER LASERKLASSE 2
MAXIMALE AUSGANG-
SLEISTUNG: 1 mW
WELLENLÄGE: 630~680
nm
ENTSPR. EN 60825-1
(2007) und EN 60825-1
(2014).
RAYON LASER EVITER DE
REGARDER LE RAYON
APPAREIL LASER DE
CLASSE 2 PUISSANCE DE
SORTIE: 1 mW
LONGUEUR D’ONDE
EMISE: 630~680 nm
CONFORME A EN
60825-1 (2007) et EN
60825-1 (2014).
RAYO LÁSER NO MIRAR
FIJO EL RAYO APARATO
LÁSER DE CLASE 2
MÁXIMA POTENCIA DE
SALIDA: 1 mW
LONGITUD DE ONDA
EMITIDA:
630~680 nm
CONFORME A EN
60825-1 (2007) y EN
60825-1 (2014).
ENGLISH
The following information is provided to comply with the rules imposed by international authori-
ties and refers to the correct use of your device.
STANDARD LASER SAFETY REGULATIONS
This product conforms to the applicable requirements of both CDRH 21 CFR 1040 and EN 60825-1
at the date of manufacture.
For installation, use and maintenance, it is not necessary to open the device.
WARNING: Do not attempt to open or otherwise service any components in the optics
cavity. Opening or servicing any part of the optics cavity by unauthorized personnel
may violate laser safety regulations. The optics system is a factory only repair item.
Use of controls or adjustments or performance of procedures other than those
specified herein may result in exposure to hazardous visible laser light.
Use of optical systems with the scanner will increase eye hazard. Optical instruments
include binoculars, microscopes, eye glasses and magnifying glasses.
The product utilizes a low-power laser diode. Although staring directly at the laser beam momen-
tarily causes no known biological damage, avoid staring at the beam as one would with any very
strong light source, such as the sun. Avoid that the laser beam hits the eye of an observer, even
through reflective surfaces such as mirrors, etc.
ESPAÑOL
Las informaciones siguientes son presentadas en conformidad con las disposiciones de las auto-
ridades internacionales y se refieren al uso correcto del terminal.
NORMATIVAS ESTÁNDAR PARA LA SEGURIDAD LÁSER
Este aparato resulta conforme a las normativas vigentes de seguridad láser a la fecha de produc-
ción: CDRH 21 CFR 1040 y EN 60825-1.
No es necesario abrir el aparato para la instalación, la utilización o la manutención.
ATENCIÓN: No intente abrir o de ninguna manera dar servicio a ninguno de los
componentes del receptáculo óptico. Abrir o dar servicio a las piezas del receptáculo
óptico por parte del personal no autorizado podría ser una violación a los reglamentos
de seguridad. El sistema óptico se puede reparar en la fábrica solamente.
La utilización de procedimientos o regulaciones diferentes de aquellas describidas
en la documentación puede causar una exposición peligrosa a la luz láser visible.
El uso de sistemas ópticos con el escáner aumentará el riesgo de daños oculares.
Los instrumentos ópticos incluyen binoculares, microscopios, lentes y lupas.
No intente abrir o de ninguna manera dar servicio a ninguno de los componentes del receptáculo
óptico. Abrir o dar servicio a las piezas del receptáculo óptico por parte del personal no autorizado
podría ser una violación a los reglamentos de seguridad. El sistema óptico se puede reparar en
la fábrica solamente.
La utilización de procedimientos o regulaciones diferentes de aquellas describidas en la docu-
mentación puede causar una exposición peligrosa a la luz láser visible.
El uso de sistemas ópticos con el escáner aumentará el riesgo de daños oculares. Los instrumen-
tos ópticos incluyen binoculares, microscopios, lentes y lupas.
LED CLASS
LED illuminator integrated in the imager engine is classified as “EXEMPT RISK GROUP” according
to IEC62471.
REACH WARNING
WARNING: POGO PIN BP53821 -> #001 Yellow metal part “Lead” content is
25000ppm
WEEE STATEMENT
Waste Electrical and Electronic Equipment (WEEE) Statement
English
For information about the disposal of Waste Electrical and Electronic Equipment (WEEE), please refer to the
website at www.datalogic.com.
Italian
Per informazioni sullo smaltimento delle apparecchiature elettriche ed elettroniche consultare il sito Web
www.datalogic.com.
French
Pour toute information relative à l’élimination des déchets électroniques (WEEE), veuillez consulter le site
internet www.datalogic.com.
German
Informationen zur Entsorgung von Elektro- und Elektronik- Altgeräten (WEEE) erhalten Sie auf der Webseite
www.datalogic.com.
Spanish
Si desea información acerca de los procedimientos para el desecho de los residuos del equipo eléctrico y
electrónico (WEEE), visite la página Web www.datalogic.com.
Portuguese
Para informações sobre a disposição de Sucatagem de Equipamentos Elétricos e Eletrônicos (WEEE -Waste
Electrical and Electronic Equipment), consultar o site web www.datalogic.com.
Chinese
有关处理废弃电气电子设备 (WEEE) 的信息， 请参考Datalogic 公司的网站 www.datalogic.com.
Japanese
廃電気電子機器(WEEE)の処理についての関連事項はDatalogicのサイト www.datalogic.com をご参
照下さい。.
MARKING AND EUROPEAN ECONOMIC AREAEEA
In radio systems configured with mobile computers and access points, the frequencies to be used
must be allowed by the spectrum authorities of the specific country in which the installation takes
place. Be absolutely sure that the system frequencies are correctly set to be compliant with the
spectrum requirements of the country.
The Radio modules used in this product automatically adapt to the frequencies set by the system
and do not require any parameter settings.
European Declaration of Compliance
Hereby, Datalogic S.r.l. declares that this radio equipment is in compliance with Directive 2014/53/
EU. The full text of the EU declaration of conformity is available at: www.datalogic.com. Select
the Support & Service > Downloads > Product Certifications link where you can search for your
specific product certification.
Česky [Czech]
Tímto Datalogic S.r.l. prohlašuje, že toto rádiové zařízení je ve shodě se směrnicí 2014/53/EU.
Dansk [Danish]
Herved erklæres Datalogic S.r.l. erklærer, at dette radioudstyr er i overensstemmelse med
direktiv 2014/53/EU.
Deutsch [German]
Hiermit wird Datalogic S.r.l. erklärt, dass dieses Funkgerät der Richtlinie 2014/53/EU entspricht.
Eesti [Estonian]
Käesolevaga on Datalogic S.r.l. kinnitab, et see raadioseade on kooskõlas direktiiviga 2014/53/
EL.
Español [Spanish]
Por la presente, Datalogic S.r.l. declara que este equipo de radio cumple con la Directiva 2014/53/
UE.
Ελληνική [Greek]
Με το παρόν, Datalogic S.r.l. δηλώνει ότι αυτός ο ραδιοεξοπλισμός συμμορφώνεται με την Οδηγία
2014/53/ΕΕ.
Français [French]
Par la présente, Datalogic S.r.l. déclare que cet équipement radio est conforme à la directive
2014/53/UE.
Italiano [Italian]
Con la presente Datalogic S.r.l. dichiara che questa apparecchiatura radio è conforme alla Direttiva
2014/53/UE.
Latviski [Latvian]
Ar šo Datalogic S.r.l. paziņo, ka šī radioiekārta atbilst Direktīvai 2014/53 / ES.
Lietuvių [Lithuanian]
Šiuo dokumentu „Datalogic S.r.l.“pareiškia, kad ši radijo įranga atitinka Direktyvą 2014/53/ES.
Nederlands [Dutch]
Hierbij verklaart Datalogic S.r.l. dat deze radioapparatuur voldoet aan Richtlijn 2014/53/EU.
Malti [Maltese]
Hawnhekk, Datalogic S.r.l. tiddikjara li dan it-tagħmir tar-radju huwa konformi mad-Direttiva
2014/53/UE.
Magyar [Hungarian]
A Datalogic S.r.l. kijelenti, hogy ez a rádióberendezés megfelel a 2014/53/EU irányelvnek.
Polski [Polish]
Niniejszym Datalogic S.r.l. oświadcza, że to urządzenie radiowe jest zgodne z Dyrektywą 2014/53/
UE.
Português [Portuguese]
Por meio deste, a Datalogic S.r.l. declara que este equipamento de rádio está em conformidade
com a Diretiva 2014/53/UE.
Slovensko [Slovenian]
Datalogic S.r.l. izjavlja, da je ta radijska oprema v skladu z Direktivo 2014/53/EU.
Slovensky [Slovak]
Týmto spoločnosť Datalogic S.r.l. vyhlasuje, že toto rádiové zariadenie je v súlade so smernicou
2014/53 / EÚ.
Suomi [Finnish]
Datalogic S.r.l. vakuuttaa täten, että tämä radiolaite on direktiivin 2014/53 / EU mukainen.
Svenska [Swedish]
Datalogic S.r.l. förklarar härmed att denna radioutrustning överensstämmer med direktiv
2014/53/EU.
UKCA Declaration of Conformity
Hereby, Datalogic S.r.l. declares that this radio equipment is in compliance with the Radio Equip-
ment Regulations (RER) (S.I. 2017/1206) and that the full text of the UKCA Declaration of Confor-
mity is available at the following internet address: http://www.datalogic.com. Select the Support
& Service > Downloads > Product Certifications link where you can search for your specific product
certification.
Information for the User
This device is restricted to indoor use when operating in the 5.15 to 5.35 GHz frequency range.
RADIO TECHNOLOGIES AND FREQUENCY BANDS EUROPE
CE Marking
Radio Technology Frequency Band Max Radio-Frequency
Transmitted Power
WLAN IEEE 802.11b/g/n (HT-20,
HT-40)
2.4GHz Frequency Bands:
2.412 - 2.472 MHZ WLAN 2.4: 19.98 dBm
WLAN IEEE 802.11a/n (HT-20,
HT-40)/ ac (VHT-20, VHT-40, VHT80)
5GHz Frequency Bands:
5.180 - 5.240 MHz
5.260 - 5.320 MHz
5.500 - 5.700 MHz
WLAN 5: 22.92 dBm
Bluetooth V5.1 — EDR/LE 2402 - 2480 Mhz BR/EDR – BLE: 6.64 dBm
CAUTION: The device for operation in the band 5150-5350 MHz is only for indoor
use to reduce the potential for harmful interference to co-channel mobile satellite
systems.
UKCA Marking
Radio Equipment Specification Table
Low Frequency MHz High Frequency MHz Rated RF Power Output W
2400
2401
2483.5
2483
6.64 dBm
19.98 dBm
5150
5250
5470
5250
5350
5725
22.92 dBm
13.56 13.56 N/A
0.13 0.13 N/A
FCC/IC LABELING
Handheld variants
with WLAN+BT radios
Pistol Grip variants
with WLAN+BT radios
To display the FCC/IC label on the device, do the following steps:
STEP 1 - Tap the Settings icon: STEP 2 - Tap the About phone option:
STEP 3 - Tap the Regulatory labels option:
RESULT #1: ELECTRONIC LABEL
(for GUN Variant case)
RESULT #2: ELECTRONIC LABEL
(for HANDHELD Variant case)
FCC COMPLIANCE
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1)this device may not cause harmful interference, and
(2)this device must accept any interference received, including interference that may cause unde-
sired operation.
NOTICE:
This device is restricted to indoor use when operated in the 5.15 to 5.25 GHz frequency range.
Changes or modifications made to this equipment not expressly approved by Datalogic S.r.l. may
void the FCC authorization to operate this equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful inter-
ference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
y Reorient or relocate the receiving antenna.
y Increase the separation between the equipment and receiver.
y Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
y Consult the dealer or an experienced radio/TV technician for help.
ISED COMPLIANCE
NOTICE:
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1)this device may not cause harmful interference, and
(2)this device must accept any interference received, including interference that may cause unde-
sired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouil-
lage est susceptible d’en compromettre le fonctionnement.
CAUTION
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the poten-
tial for harmful interference to cochannel mobile satellite systems;
(ii) high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-
5350MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to
LE-LAN devices.
AVERTISSEMENT:
(i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement pour
une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de
satellites mobiles utilisant les mêmes canaux;
(ii) les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d.,
qu’ils ont la priorité) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars
pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.
RADIO TECHNOLOGIES AND FREQUENCY BANDS USA AND
CANADA
Radio Technology Frequency Bands
WiFi WLAN IEEE 802.11b/g/n (HT-20, HT-40) 2.4GHz Frequency Bands:
2.412 - 2.462 MHZ
WLAN IEEE 802.11a/n (HT-20, HT-40)/ ac (VHT-20, VHT-40, VHT80)
5GHz Frequency Bands:
5.180— 5.240 MHz
5.260— 5.320 MHz
5.500— 5.700 MHz, 5.720 MHz
5.735— 5.825 MHz
Bluetoothe V5.1 — EDR/LE 2402-2480 Mhz
RADIO FREQUENCY EXPOSURE INFORMATION
The JOYA TOUCH 22 is designed to be held by the End User hands and carried close to the End User
body only using the belt holster accessory.
The JOYA TOUCH 22 is equipped by loudspeaker only, thus it is designed for VoIP calls on loudspe-
aker only and far away from the user’s head.
CE SAR Compliance
The JOYA TOUCH 22 complies with CE SAR limits for general population/uncontrolled expo-
sure specified in Council Recommendation 1999/519/EC, ICNIRP Guidelines and RED (Directive
2014/53/EU).
The JOYA TOUCH 22 has been tested for handheld and typical body-worn use (0mm distance from
the body, using a belt holster), according to EN 50360:2017, EN50566:2017, EN 62311: 2020, EN
50665:2017, EN 62479:2010, EN 50663:2017 and EN 62209-2:2010.
For body-worn use the device must be properly held in the Datalogic genuine holster.
In order to meet the CE SAR Compliance, only genuine Datalogic Belt Holster for JOYA TOUCH 22
must be used.
The use of third-party holsters (or similar accessories) may not comply with CE SAR compliance
requirements, thus should be avoided.
The genuine Datalogic belt holster must be properly worn, so that the JOYA TOUCH 22 faces to the
end user body its front (display) side or its back (battery) side.
Refer to https://www.datalogic.com for JOYA TOUCH 22 genuine holster and accessories.
FCC/ISED SAR Compliance
The JOYA TOUCH 22 complies with the FCC SAR limits specified in the FCC 47 CFR part2 (2.1093)
and ANSI/IEEE C95.1- 1992, and it complies with the ISED SAR limits specified in ISED RSS-102
Issue 5 (2015).
The JOYA TOUCH 22 has been tested for handheld and typical body-worn use (0mm distance from
the body, using a belt holster), according to the specific SAR testing method referred at the Display
Exhibits section of https://apps.fcc.gov/oetcf/eas/reports/GenericSearch.cfm, filling the FCC IDs
specified in the FCC/IC labeling section of this Addendum.
In order to meet the FCC/ISED SAR Compliance, only genuine Datalogic Belt Holster for JOYA
TOUCH 22 must be used. The use of third-party holsters (or similar accessories) may not comply
with FCC/ISED SAR compliance requirements, thus should be avoided.
The genuine Datalogic holster must be properly worn, so that the JOYA TOUCH 22 faces to the end
user body its front (display) side or its back (battery) side. Refer to https://www.datalogic.com for
JOYA TOUCH 22 genuine holster and accessories.
Cet équipement peut être utilisé dans votres mains. Cet équipement peut être utilisé et installé à
une distance minimale de 0mm entre le radiateur et votres corps seulement avec le Belt Holster
accessoire pour JOYA TOUCH 22.
Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar
interferência em sistemas devidamente autorizados.
La operación de este equipo está sujeta a las siguientes dos condiciones.
1. Es posible que este equipo o dispositivo no cause interferencia perjudicial.
2. Este equipo o dispositivo debe aceptar cualquier interferencia. Incluyendo la que pueda causar
su operación no deseada.
微功率设备应当在其产品使用说明（含电子显示的说明书）中注明以下内容：
　　（一）符合“微功率短距离无线电发射设备目录和技术要求”的具体条款和使用场景，采用的
天线类型和性能，控制、调整及开关等使用方法；
　　（二）不得擅自改变使用场景或使用条件、扩大发射频率范围、加大发射功率（包括额外加装
射频功率放大器），不得擅自更改发射天线；
　　（三）不得对其他合法的无线电台（站）产生有害干扰，也不得提出免受有害干扰保护；
　　（四）应当承受辐射射频能量的工业、科学及医疗（ISM）应用设备的干扰或其他合法的无线电
台（站）干扰；
　　（五）如对其他合法的无线电台（站）产生有害干扰时，应立即停止使用，并采取措施消除干
扰后方可继续使用；
　　（六）在航空器内和依据法律法规、国家有关规定、标准划设的射电天文台、气象雷达站、卫
星地球站（含测控、测距、接收、导航站）等军民用无线电台（站）、机场等的电磁环境保护区域
内使用微功率设备，应当遵守电磁环境保护及相关行业主管部门的规定；
　　（七）禁止在以机场跑道中心点为圆心、半径5000米的区域内使用各类模型遥控器；
　　（八）微功率设备使用时温度和电压的环境条件。
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Datalogic JOYA Touch 22 Multi Purpose Device for Retail Manuel utilisateur

Datalogic
Marque
Datalogic
Modèle
JOYA Touch 22 Multi Purpose Device for Retail
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents