EarthWise SN74022 Le manuel du propriétaire

Catégorie
Tondeuses à gazon
Taper
Le manuel du propriétaire
Model SN74022
OWNER’S MANUAL
22-IN Lithium Snow Thrower
Copyright All Rights Reserved.
SAVE THIS MANUAL FOR FUTURE REFERENCE
This product has been engineered and manufactured to our high standard for dependability, ease of operation, and
operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the owner’s manual
before using this product.
CA Compliant Charger
Included (Model No.
CHL80040)
BATTERY MUST BE CHARGED
BEFORE FIRST USE. TWO TO
THREE INITIAL CHARGING/
DISCHARGING CYCLES MAY BE
REQUIRED TO ACHIEVE
MAXIMUM RUN TIME/CAPACITY.
Quick Start Instruction
From Page 9
Thank you for your purchase.
DO NOT RETURN THIS PRODUCT TO THE STORE. OPERATING, ASSEMBLY, PART,
SERVICE QUESTIONS? GO TO AMERICANLAWNMOWER.COM OR CALL 1-800-633-1501
BETWEEN 8 AM 5 PM EST, MONDAY-FRIDAY FOR ASSISTANCE.
Precautions that involve your safety.
Keep the electrical cord free of the auger. The auger may
damage the cord and cause contact with live parts.
CAUTION! Read the instruction manual and
follow the warning and safety instructions!
DANGER! Rotating auger. Keep hands and feet at a safe
distance.
CAUTION! Remove plug from outlet
immediately if the cable is damaged or cut.
Do not place hand under auger.
SWITCH OFF! the machine, wait until it comes
to a complete standstill and remove battery
prior to maintenance, cleaning or repair work!
Do not place hand in front of chute deflector.
CAUTION! Always wear eye and ear
protection.
Do not expose to rain or use in damp locations.
Wear safe, sturdy, nonskid footwear! DANGER! Risk of electric shock.
DANGER! objects may be thrown out at high
speed when motor is running. Do not walk in
front of running machine.
Do not use in rain or electrical storms.
Keep bystanders at a safe distance.
Waste electrical products should not be disposed of with household waste. Please recycle
where facilities exist. Check with your Local Authority or retailer for recycling advice.
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the product better and safer.
2
Model SN74022
TO REDUCE RISK OF INJURY: Before any use
be sure everyone using this product reads and
understands all safety instructions and other
information contained in this manual.
CAUTION: Wear appropriate personal hearing
protection during use. Under some conditions and
duration of use, noise from this product may
contribute to hearing loss.
Save these instructions and review frequently prior
to use and in instructing others.
WARNING: When using electric appliances, basic
safety precautions should always be followed to
reduce risk of fire, electric shock, and personal
injury, including the following:
READ ALL INSTRUCTIONS
IMPORTANT SAFETY WARNINGS
GENERAL SAFETY
Disconnect the battery pack from the appliance before
making any adjustments, changing accessories, or
storing appliance. Such preventive safety measures
reduce the risk of starting the appliance accidentally.
Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with
another battery pack.
Use appliances only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
When battery pack is not in use, keep it away from other
metal objects, like paper clips, coins, keys, nails, screws or
other small metal objects, that can make a connection from
one terminal to another. Shorting the battery terminals
together may cause burns or a fire.
Under abusive conditions, liquid may be ejected from the
battery; avoid contact. If contact accidentally occurs, flush
with water. If liquid contacts eyes, additionally seek medical
help. Liquid ejected from the battery may cause irritation or
burns.
Do not use a battery pack or appliance that is
damaged or modified. Damaged or modified
batteries may exhibit unpredictable behavior resulting
in fire, explosion or risk of injury.
Do not expose a battery pack or appliance to fire or
excessive temperature. Exposure to fire or
temperature above 130°C may cause explosion. The
temperature of 130°C can be replaced
by the temperature of 265°F.
Follow all charging instructions and do not charge the
battery pack or appliance outside of the temperature
range specified in the instructions. Charging
improperly or at temperatures outside of the specified
range may damage the battery and increase the risk
of fire.
Have servicing performed by a qualified repair person
using only identical replacement parts.
This will ensure that the safety of the product is
maintained.
Do not modify or attempt to repair the appliance or
the battery pack (as applicable) except as indicated
in the instructions for use and care.
CHECK FOR DAMAGED PARTS - Before further
use of the product, any part that is damaged should
be carefully checked to determine that it will operate
properly and perform its intended function. Check
for alignment of moving parts, binding of moving
parts, breakage of parts, mounting and any other
condition that may affect its operation. Any part that
is damaged should be properly repaired or replaced.
For assistance call our customer service help line at
1-800-633-1501.
AVOID DANGEROUS ENVIRONMENTS - Do
not operate in gaseous or explosive atmospheres.
Motors in these products normally spark, and the
sparks might ignite fumes.
KEEP CHILDREN AWAY - All visitors, children and
pets should stay at a safe distance from the work
area.
DRESS PROPERLY- Don’t wear loose clothing or
jewelry and wear protective hair covering to contain
long hair. They can be caught in moving parts.
Wear safe, sturdy, nonskid footwear. Maintain good
footing at all times, especially on slopes.
USE SAFETY GLASSES - Wear safety glasses
with side shields or goggles that are marked to
comply with ANSI Z87.1 standard when operating
this product.
WARNING: Keep hands away from moving parts.
Never put your hands near the auger to remove
snow, sticks or other debris. Blocked auger can
“spring back” when cleared and may cause
personal injury even when the snow thrower is
stopped. Always use a wooden stick such as a
broom handle to clear blockages.
REMOVE THE BATTERY from the snow thrower
when not in use or when servicing or cleaning. Do
not leave unattended.
USE RIGHT APPLIANCE - Do not use this product
for any job except that for which it is intended.
AVOID ACCIDENTAL STARTING—Don’t carry
snow thrower with finger on switch when the battery
is installed. Be sure switch is off when installing
battery.
DO NOT OVERLOAD the snow thrower by using at
too fast a rate to clear the snow. The snow thrower
will perform better and safer at the rate for which it
was designed.
DON’T OVERREACH - Guide the snow thrower at
a walking pace only. Keep proper footing and
balance at all times.
LIGHTING - Only operate your snow thrower in
daylight or good artificial light.
STORE IDLE UNIT INDOORS-When not in use,
the snow thrower should be stored indoors in a dry
area out of reach of children.
MAINTAIN UNIT WITH CARE-Keep clean for best
performance and to reduce the risk of injury.
Keep handles dry, clean and free from oil.
Do not operate the snow thrower on a slope that is
too steep for safe operation. When on slopes, slow
down and make sure you have good footing.
Before starting the snow thrower make sure the
auger is not touching any object and is free to
move.
Do not attempt to clear snow from a gravel or
crushed rock surface. This product is only intended
for use on hard, flat surfaces free of sand, stone
and debris, wires or any other objects.
Operation of the snow thrower in the hand-held
position is unsafe except in accordance with the
special instructions for such use provided in the
operator’s manual.
CAUTION: Never throw snow towards people, pets
or cars and never allow anyone in front of the snow
thrower while in operation.
Objects that might clog the snow thrower or cause
other damage can be hidden in the snow. Clear the
area of doormats, sleds, boards, wires and other
debris prior to use.
If the auger strikes a foreign object, stop the snow
thrower and examine it for signs of damage. Make
any necessary repairs before restarting and
continuing to work.
STAY ALERT - Watch what you are doing. Use
common sense. Do not operate the snow thrower
when you are tired or under the influence of drugs,
alcohol or medications.
GENERAL SAFETY
3
Model SN74022
GENERAL SAFETY
If the snow thrower starts to vibrate abnormally, turn it off
immediately and check for the cause. Vibration is
generally a warning of trouble.
Always turn off the snow thrower, wait until the auger
comes to a complete stop and remove the battery before
carrying out maintenance or repairs.
Never operate the snow thrower without proper guards
and other safety protective devices in place and
working.
GENERAL SAFETY
SAFETY RULES FOR CHARGER
FCC WARNING:
Please note that changes or modifications to this
product not expressly approved by the party
responsible for compliance could void the user's
authority to operate the equipment.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and
receiver.
-- Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV
technician for help.
Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away from
heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
Use of an attachment not recommended or sold by the
battery charger manufacturer may result in a risk of fire,
electric shock, or injury to persons. Following this rule will
reduce the risk of electric shock, fire, or serious personal
injury.
Do not service snow thrower with battery, switch key, or
charger installed.
Do not use the charger when the ambient temperature is
above 100°F (37.8°C) or below 32°F (0°C)
Do not operate charger with a damaged cord or plug
which could cause shorting and electric shock. If
damaged, replace the charger with an identical charger.
Do not operate charger if it has received a sharp blow,
been dropped or otherwise damaged in any way. Take it
to a qualified individual for electrical check to determine if
the charger is in good working order.
Unplug charger from outlet before attempting any
maintenance or cleaning to reduce the risk of electric
shock.
Disconnect charger from the power supply when not in
use to prevent damage to the charger during a power
surge.
Risk of electric shock, Do not touch uninsulated portion of
output connector or uninsulated battery terminal.
Do not expose charger to wet or damp conditions, Water
entering charger will increase the risk of electric shock.
Make sure cord is located so that it will not be stepped on,
tripped over, come in contact with sharp edges or moving
parts or otherwise subjected to damage or stress. This will
reduce the risk of accidental falls, which could cause
injury and damage to the cord, which could result in
electric shock.
Keep cord and charger away from heat to prevent
damage to housing or internal parts.
Do not let gasoline, oils, petroleum-based products, etc.
come in contact with plastic parts. They contain chemicals
that can damage, weaken or destroy plastic.
An extension cord should not be used unless
absolutely necessary. Use of improper extension cord
could result in a risk of fire and electric shock. If
extension cord must be used, make sure:
a. That pins on plug of extension cord are the same
number, size and shape as those of plug on
charger
b. That extension cord is properly wired and in good
condition; and
c. That wire size is large enough for AC ampere
rating of charger as specified below:
Cord length (Feet) - 25’ 50’ 100’
Cord Size (AWG) - 16 16 16
NOTE: AWG= American Wire Gauge
Save these instructions. Refer to them frequently and
use them to instruct others who may use this product.
If you loan someone this snow thrower, loan them
these instructions also.
WARNING: Keep all connections dry and off the
ground. Do not touch plug with wet hands.
CAUTION: Auger does not stop immediately after the
snow thrower is turned off.
CAUTION: Risk of injury. This snow thrower is capable
of causing serious injury. Do not put hands, feet or any
body part or clothing near the rotating auger.
WARNING: California Proposition 65:
This product contains chemicals known to the State of
California to cause cancer, birth defects or other
reproductive harm.
WARNING: Cancer and Reproductive Harm -
www.P65Warnings.ca.gov.
4
Model SN74022
PRODUCT SPECIFICATIONS
Model: SN74022
Power supply voltage: 40V, DC only Clearing width: 22 inches (560 mm)
Speed: 2000 RPM Max clearing depth: 12 inches (305 mm)
Battery: 40V, 4.0 Ah Lithium-ion Max clearing capacity: 600 pounds/minute
Charging time: 2.5 hours Max throwing distance: Up to 30 feet
Battery run time: Up to 30 minutes Weight: 32.4 pounds
PARTS LIST
No. Description
1 Upper handle
2 Bail wire
3 Switch button
4 Cable clip
5 Crank handle
5A Upper crank
5B Lower crank
6 J bolt
7 Knob
8 Center handle
9 Cotter pin
No. Description
10 Auxiliary handle
11 Battery
compartment
12 Lower handle
13 Wheel assy.
14 Scraper blade
15 Auger
16 Side cover
17 Discharge chute
18 Chute deflector
19 Battery pack
20 Charger
19
20
5
Model SN74022
5A
5B
ASSEMBLY
UNPACKING
This product requires assembly.
Carefully remove everything from the box. Make sure that
all items listed in the packing list are included.
Inspect all items carefully to make sure no breakage or
damage occurred during shipping.
Do not discard the packing material until you have
carefully inspected and satisfactorily operated the snow
thrower.
If any parts are damaged or missing, please call our
customer service help line at 1-800-633-1501 for
assistance.
PACKING LIST
- Snow Thrower
- Handle Assembly
- Chute Crank
- Chute Deflector
- Battery & Charger
- Hardware Bag
- Owner’s Manual
INSTALLING CENTER HANDLE
Position the center handle onto the lower handles and
make sure the bracket is pointed downward. (See Fig
1)
Align the holes on the center handle with the holes in
the lower handle as shown. (See Fig 2)
Insert J-bolt through both handles with the threaded
end at the bottom and facing inside. (See Fig 3)
Install the handle knob and tighten securely to secure
the bolt in place. (See Fig 4)
Repeat on the opposite side to secure the center
handle in place. (See Fig 5)
Fig. 5
Fig. 4
Fig. 3
Fig. 2
Fig. 1
6
Model SN74022
INSTALLING CHUTE CRANK
Install the upper chute crank through the bracket
located on the center handle. (See Fig 8)
Align the holes in the upper and lower cranks and
insert the cotter pin through the holes as shown to
secure. (See Fig 9 and Fig 10)
Turn the lever left and right to verify the proper
functioning of the crank and the chute.
ASSEMBLY
INSTALLING UPPER HANDLE
Align the holes on the upper handle with the holes in
the center handle as shown. (See Fig 6)
Insert threaded end of J bolt through both handles with
the threaded end facing inside.
Install the handle knob and tighten secure.
Repeat on the opposite side.
Secure the cable clip to handles. (See Fig 7).
Fig. 8
Fig. 9
Fig. 10
Fig. 6
Fig. 7
7
Model SN74022
8
Model SN74022
INSTALLING CHUTE DEFLECTOR
Take the washer out of hardware bag. (See Fig 11)
Position the washer onto the discharge chute. (See
Fig 12)
Position the chute deflector over the discharge chute.
Align the holes and place the washer between the
deflector and chute. (See Fig 13)
Tighten the knobs firmly. (See Fig 14 - 15)
Fig. 12
Fig. 11
ASSEMBLY
Fig. 14
Fig. 15
Fig. 13
Removing snow
Before starting work, thoroughly inspect the area where
the equipment is to be used and remove all doormats
sleds, boards, wires and any other foreign objects.
Check the condition of the snow thrower before operating
it to ensure that the auger turns freely.
Check the auger for wear and tear at regular intervals.
Make sure all fasteners on the snow thrower (screws,
nuts, etc.) are fully tightened.
Position the discharge chute so that snow will discharge
in a safe direction. Do not direct the discharge towards
people or areas where property can be damaged. Keep
children, pets and others away for the work area. Do not
walk in front of the snow thrower when it is running.
Direct the discharge to the right or left by turning the
discharge chute with the chute crank. The chute can be
adjusted up to 180 degrees.
The chute deflector on the top of the discharge chute
controls the height of the discharge. Loosen both of the
knobs to raise or lower the deflector to the desired height
and tighten the knobs to secure the deflector.
NOTE: Do not over-tighten the knobs.
For the most efficient snow removal throw the snow
downwind and slightly overlap each swath.
Push the snow thrower forward at a comfortable rate of
speed, yet slow enough to clear the path completely. The
width and depth of the snow determines your forward
speed.
When turning at the end of a swath, use the wheel on
one side as the pivot point. Slightly tilt the snow thrower
on this pivot point while turning.
The snow thrower can remove up to 12 inches deep in
one pass. To shave down larger banks of snow, lift the
snow thrower by the primary and auxiliary handles and
place the snow thrower on the bank. Let the weight of
the snow thrower shave down the bank by rocking it in a
back-and-forth motion.
When clearing steps, hold the snow thrower by the
primary and auxiliary handles and use a swinging or
sweeping motion.
Clear snow often, before it gets too deep. It is best to
remove the snow as soon as possible after it falls.
Some parts of the snow thrower may freeze under
extreme temperature conditions. If parts freeze while the
snow thrower is in use, stop the snow thrower, remove
the battery and inspect for frozen parts. Free all parts of
ice before restarting or operating the snow thrower. Do
not attempt to operate the snow thrower with frozen parts
or try to force controls that are frozen.
OPERATING
Install battery
BATTERY MUST BE CHARGED BEFORE FIRST USE.
Open the battery compartment cover and slide the
battery down until it clicks to lock it into position, then
close the battery department cover.
Turning On and Off
WARNING: The auger starts rotating immediately after
the snow thrower is switched on. Keep hands and feet
away from the auger.
To switch ON, make sure the auger is not touching any
surface. Press down and hold the safety lock off button
(1). While holding down the button pull back on bail wire
(2). Once the snow thrower is started you can release the
safety lock off button.
To switch off simply release the bail wire.
LED HEADLIGHTS
LED headlights are located on the upper handle to
illuminate your path when using the snow blower in low
light conditions.
The lights may be turned on when the snow thrower is
operating. After the snow thrower is engaged by pressing
the safety lock button and pulling the bail wire toward the
handle, the lights may be turned on by pressing the on-off
switch to the on position. Lights will go out when the bail
wire is released. (See Fig 16)
The lights will illuminate when the bail wire is pulled as
long as the on-off switch remains in the on position.
When job is completed, press switch to the off position.
Fig 16
ON/ OFF BUTTON
9
Model SN74022
OPERATING
After clearing the snow, continue to run the snow thrower
for a few minutes to prevent ice from freezing on moving
parts. Then switch off the motor, wait for all moving parts
to stop, and wipe the ice and snow from the snow
thrower with a clean rag.
WARNING: To avoid serious personal injury, do not use
hands or feet to unclog the chute.
Before unclogging the chute, shut off the snow thrower
and remove the battery pack. Wait for the auger to stop
turning. Clean out the chute with a wooden stick such as
a broom handle.
If the snow thrower should start to vibrate abnormally,
immediately stop the motor and check for the cause.
Vibration is generally a warning of trouble.
Look behind and use care when backing up with the
snow thrower.
For large areas a definite pattern of operation is required
to thoroughly clean an area of snow. These patterns
will avoid throwing snow in unwanted places as well as
eliminating a second removal of snow.
Pattern A: Throw the snow to the right or left side where
it is possible. For areas such as a long driveway it is
advantageous to start in the middle. Plow from one end
to the other, throwing snow to both sides.
Pattern B: If the snow can only be thrown to one side of
the area to be cleared, start on the opposite side.
Overload Protection
The over current controller will automatically turn off the
snow thrower within 2 seconds when the current is over
25A. If the motor stops, you can restart the snow thrower
immediately if needed.
10
Model SN74022
MAINTENANCE
Replacing the scraper
The scraper is located at the base of the snow thrower
beneath the auger housing.
Remove the screws that secure the scraper to the snow
thrower.
Install the new scraper and fasten it securely with the
screws. (See Fig 17)
Replacing the auger belt
Under normal operating conditions it should not be
necessary to replace the auger belt. However, should
the auger jam or malfunction the belt could be damaged.
To replace the belt follow these instructions.
Belt drive system structure (See Fig 18)
Regular cleaning and maintenance of your snow thrower
will ensure efficiency and prolong the life of the product.
Check all fasteners at frequent intervals for proper
tightness to be sure the snow thrower is in safe working
condition.
After each use, let the motor run for a few minutes so that
moving parts do not freeze. Then shut off the motor, wait
for all moving parts to stop, and wipe the ice and snow
from the snow thrower. Rotate the chute crank several
times to remove snow.
Only use a cloth soaked with hot water and a soft brush
to clean the snow thrower. Never wet or spray water on
the machine!
Do not use detergents or solvents as these could cause
irreparable damage to the snow thrower. Chemicals can
destroy the plastic parts.
To protect the snow thrower from corrosion when storing
for long periods, lightly oil the metal parts.
Store the snow thrower in a dry area out of reach of
children.
For the user’s safety, worn or damaged parts must be
replaced. Replace with original replacement parts only.
Parts from another snow thrower may not fit properly
causing an unsafe situation.
Lubricating the snow thrower
You do not need to lubricate the snow thrower. All of the
bearings are sealed and were lubricated at the factory for
the life of the snow thrower.
Replacing the rubber plates on auger
Detach the worn rubber plate by removing the two sets of
nuts, bolts, and washers used to secure it.
Install the new rubber plate.
Insert the bolt with the small flat washer into the
corresponding holes on each end of the rubber plate.
Use a large flat washer and locknut to secure the bolt
on each end.
Install the other rubber plate in the same manner.
Fig. 18
Fig 17
Before carrying out maintenance operations, remove the battery pack.
Auger Pulley
Auger Belt
Drive Pulley
11
Model SN74022
MAINTENANCE
1. Open the left side plate by removing three screws.
(Fig. 19)
2. Use your right hand to turn the rib side of the belt
up and pull upwards while turning the auger pulley
counterclockwise with your left hand. The belt can be
easily removed from the pulley. (Fig. 20 - 21)
3. Put the belt on the drive pulley first and then place
the belt at the lower end of the auger pulley. (Fig. 22)
4. Use right hand to press the belt with ribbed side
down. (Fig. 23)
5. While holding the belt down with your right hand use
your left hand to turn the auger forward so that the
auger pulley rotates in a clockwise direction. (Fig. 24)
Fig. 19
Screw
Fig. 20
Fig. 21
Fig. 22
Fig. 23
Fig. 24
12
Model SN74022
MAINTENANCE
6. Keep pressure on the belt with your right hand (rib
side down and flat side up) while rotating the auger.
The belt will be gradually pushed down onto the
pulley. When the belt is seated on the pulley, adjust
it so that the ribs of the belt match the grooves on
the pulley. (Fig. 25 - 28)
Fig. 24
7. After belt is installed, replace the side plate and
secure it with the three screws. (Fig. 29)
Fig. 27
Fig. 26
Fig. 29
Fig. 28
Fig. 25
Screw
13
Model SN74022
CHARGING THE BATTERY PACK
BATTERY METER
Since the snow thrower battery is shipped in a low
charge condition, the battery must be charged before
use. The battery has 3 LED lights to indicate battery
capacity. These lights will only illuminate when the light
indicator button is pushed.
If three GREEN lights illuminate, the battery is charged
and ready for use. Two green lights are equal to 25%-
80% charge, while one green light is equal to 5%-25%
charge.
It is recommended to charge battery pack when one light
is illuminated.
CHARGING THE BATTERY PACK
The snow thrower comes with a maintenance free,
sealed, 40 volt storage battery.
Charge the battery pack only with the charger
provided.
Allow at least two hours of charge time before initial
use of the snow thrower.
Make sure the power supply is normal household
voltage, 120 volts, 60Hz, AC only.
The battery should be charged in a cool, dry place.
To improve battery life, store battery indoors in a
controlled climate. Fully charge battery pack every
3 months.
Since the battery will not develop a memory, it does
not have to be fully discharged before recharging.
2 to 3 initial charging/discharging cycles may be
required to achieve maximum run time/capacity.
When fully charged, the battery can be safely stored
in temperatures down to 4˚F(-20˚C) for a period of
up to one month before requiring charging. Fully
charge battery pack every 3 months.
The battery charger should be operated in
temperatures between 32˚F and 100˚F(0˚C and
37.8˚C).
TO CHARGE
Insert the 120 volt plug of the charger into the wall
receptacle. Light A will illuminate and stay green.
(Fig. 30)
Fig. 30
Place the battery pack into the charger by sliding
the pack as shown in Fig. 13 to lock it into position.
Light B will illuminate red to indicate that the battery
is charging and the three lights on the battery pack
will cycle in green.
When the battery pack is fully charged, light B will
turn green and the lights on the battery pack will shut
off. (Fig 31)
NOTE: Typical time required to reach a full charge is
2 1/2 hours.
NOTE: If light A remains green while light B alternately
flashes red and green, this indicates a temperature
abnormality (i.e. that the battery pack is either too hot or
too cold). If there is only a red blinking light, this indicates
that something is wrong with the battery. Contact
Earthwise customer service center at 1-800-633-1501 for
assistance.
If the charging light indicator Light B alternately blinks red
and green or it does not come on at all, check that the
battery pack is fully seated into the bay. Remove the pack
and reinsert. If the problem persists, contact the
Earthwise customer service center at 1-800-633-1501 for
assistance.
Fig. 31
14
Model SN74022
Run the snow thrower for a few minutes to melt away any
snow on the snow thrower.
Remove the battery pack from the snow thrower.
Examine the snow thrower thoroughly for worn, loose, or
damaged parts. Check connections and screws and
tighten if necessary. To repair or replace parts, contact
our customer service help line at 1-800-633-1501.
Store the snow thrower, along with the removed battery
pack, in a clean, dry place out of reach of children. Cover
loosely with a tarp for added protection.
STORAGE
BATTERY DISPOSAL
Remove the battery pack from the snow thrower. Cover the terminals with heavy duty adhesive tape. Do not attempt to destroy or disassemble battery
pack or remove any components. This product contains lithium-ion batteries which must be recycled or disposed of properly. Local, state or federal
laws may prohibit disposal of these batteries in ordinary trash.
The RBRC seal on the li-ion battery pack indicates that the costs to recycle the battery pack at the end of its useful life has already been
paid by The Great States Corporation American Lawn Mower Company. It is illegal to place spent li-ion batteries in the local municipal
solid waste or in the trash. RBRC in cooperation with The Great States Corporation American Lawn Mower Company has provided an
environmentally friendly and easy way to recycle spent li-ion batteries. Just contact your local recycling center or call 1-800-8BATTERY
for information on where to drop off the spent battery.
CHARGING THE BATTERY PACK
SLEEP MODE:
If the light indicator button is continuously pressed for
more than 30 seconds, the lights will go into sleep mode.
When light indicator button is pushed, no lights illuminate
(This can occasionally occur during transportation).
To re-activate battery LED lights, place the battery on the
charger and charge for one to two minutes. Battery
indicator will function normally.
15
Model SN74022
TROUBLESHOOTING
Problem Possible causes Remedy
Motor does not start Battery not making contact.
Lock off not fully operated.
Battery not installed properly.
Battery not charged.
Check battery is fully inserted.
Check that lock off is fully forward prior to moving
trigger.
Check battery installation.
Check battery charging requirements.
Poor results Drive belt worn or damaged.
Auger worn or damaged.
Discharge blocked.
Replace the drive belt.
Replace the auger. Ensure the screws and nuts are
properly tightened.
Switch off the snow thrower, remove the battery
pack, and clean the discharge.
Abnormal vibrations Drive belt worn or damaged.
Auger worn or damaged.
Scraper blade worn or damaged.
Replace the drive belt.
Replace the auger. Ensure the screws and nuts are
properly tightened.
Replace the scraper blade. Ensure the screws are
properly tightened.
Battery LED lights will
not illuminate
Battery in sleep mode Place battery on charger for one to two minutes.
16
Model SN74022
17
Model SN74022
PARTS AND SERVICE
For parts or service, please call 1-800-633-1501 or visit us online at americanlawnmower.com. Be
sure to provide all relevant information when you call or visit.
REPAIR PARTS (KITS/ ITEMS)
The model/ serial number of this tool is found on a plate or label attached to the housing. Please
record the serial number in the space provided below.
MODEL NUMBER SN74022 ___
SERIAL NUMBER________________
Always mention the model number when ordering kits/items for this tool.
CALL US FIRST !!
Call us first with questions about operating or maintaining your tool
at 1-800-633-1501 between 8:00 a.m. 5:00 p.m. Eastern
Standard Time, or get assistance on www.americanlawnmower.com.
No. Kit/Item Number Description QTY
1 SN18-CHK-1 Center Handle Kit 1
2 SN22-AK Auger Kit 1
3 SN18-HWK-1 Hardware Kit 1
4 SN22-SB Scraper Blade/ Fender Kit 1
5 SN18-ACK-1 Adjusting Cover Kit 1
6 WK-TC-SN Wheel Kit 1
7 SN4018-BELT Drive belt kit 1
8 SN18-CKH-1 Crank Handle Kit 1
9 BL84040 Battery Pack 1
10 CHL80040 Charger 1
WARRANTY POLICY
Earthwise warrants to the original owner that each new product and service part is free from defects
in materials and workmanship and agrees to repair or replace any defective product or part for the
warranty period as stated above from the original date of purchase except for the conditions and
circumstances listed below:
American Lawn Mower Company
The Great States Corporation
7444 Shadeland Station Way
Indianapolis, IN 46256
Phone 1-800-633-1501
www.americanlawnmower.com
In a continued commitment to improve quality, the Manufacturer reserves the right to
make component changes or design changes when necessary.
OWNER’S MANUAL
22-IN Lithium Snow Thrower
Copyright All Rights Reserved.
Rev. 9/9/2019
Two (2) year limited warranty on Earthwise 40 volt outdoor power equipment and one (1) year
limited warranty on Earthwise 40 volt battery packs and chargers.
This warranty applies only to the original purchaser at
retail and may not be transferred.
Warranty applies if the product is used for personal,
household or family use. Warranty is void if product is
used for commercial, industrial or rental purposes.
Warranty does not include repairs necessary due to
operator’s abuse or negligence (including
overloading the product beyond capacity or
immersion in water), or the failure to assemble,
operate, maintain or store the product according to
the instructions in the owner’s manual.
This warranty is not transferable
and only applies to product sold
directly from an authorized
retailer. This warranty does not apply to any
product, new or used, purchased through
unauthorized third-party channels.
ANY INCIDENTAL, INDIRECT OR
CONSEQUENTIAL LOSS, DAMAGE, OR
EXPENSE THAT MAY RESULT FROM ANY
DEFECT, FAILURE OR MALFUNCTION OF THE
PRODUCT IS NOT COVERED BY THE
WARRANTY. Some states do not allow the
exclusion or limitation on how long an implied
warranty lasts, so the above limitation may not apply
to you.
Products sold damaged or incomplete, sold “as is”, or
sold as reconditioned are not covered under the
warranty.
Damage or liability caused by shipping, improper
handling, improper assembly, incorrect voltage,
improper wiring, improper maintenance, improper
modification or the use of accessories and/or
attachments not specifically recommended is not
covered by this warranty.
Expendable items that become worn during normal use
are not covered by the warranty.
Warranty does not cover damage caused by cold, heat,
rain, excessive humidity, corrosive environments and
materials, or other contaminants.
Warranty does not include installation, assembly or
normal adjustments explained in the owner’s manual.
The expense of delivering the product to the vendor and
the expense of returning the product or replacement
parts to the owner is not covered by the warranty.
The warranty does not cover normal deterioration of the
exterior finish, including but not limited to scratches,
dents, paint chips or any corrosion or discoloration
caused by heat, abrasive and chemical cleaners.
Proof of purchase, original dated sales receipt, must accompany all
warranty claims.
Modelo SN74022
EL MANUAL DEL PROPIETARIO
Sopladora de nieve de 560 mm (22 pulg.) de Litio
Copyright. Todos los derechos reservados.
GUARDE ESTE MANUAL PARA CONSULTAS FUTURAS
Este producto fue diseñado y fabricado de acuerdo con nuestros altos estándares de confiabilidad, facilidad de operación y seguridad
para el operario. Si se trata con cuidado, esta herramienta le otorgará os de óptimo rendimiento y resistencia.
ADVERTENCIA: Para reducir el riesgo de sufrir alguna lesión, el usuario debe leer y comprender
el manual del propietario antes de usar este producto.
Cargador Cumple con
CA está incluido
(Modelo No.
CHL80040)
DEBE CARGAR LA BATERÍA ANTES
DE UTILIZARLA POR PRIMERA VEZ.
ES POSIBLE QUE SE NECESITEN DE
DOS A TRES CICLOS DE CARGA/
DESCARGA INICIALES PARA
OBTENER LA MÁ XIMA CAPACIDAD O
TIEMPO DE FUNCIONAMIENTO.
Instrucción de inicio rápido
De la pagina 9
NO DEVUELVA ESTE PRODUCTO A LA TIENDA. ¿ TIENE PREGUNTAS SOBRE FUNCIONAMIENTO,
MONTAJE, PIEZAS O SERVICIO TÉ CNICO? IR A WWW.AMERICANLAWNMOWER.COM O LLAME AL
1-800-633-1501 ENTRE LAS 8:00 AM Y LAS 5:00 PM, HORA DEL ESTE DE LOS ESTADOS UNIDOS.
Muchas gracias por su compra.
Los productos eléctricos no se deben desechar junto con los residuos domésticos. Recicle donde haya centros para tal fin.
Consulte a la autoridad local o al distribuidor minorista para obtener asesoramiento sobre reciclado.
MBOLOS
Algunos de los siguientes mbolos pueden aparecer en este producto. Tenga a bien estudiarlos y aprender su significado.
La adecuada interpretación de estos símbolos le permitirá operar el producto mejor y de manera más segura.
2
Modelo SN74022
Precauciones para su seguridad.
Mantenga el cable eléctrico lejos de la barrena. La
barrena puede dañar el cable y producir un contacto con
piezas activas.
PRECAUCIÓ N: Lea el manual de
instrucciones y atienda las instrucciones se
seguridad y advertencia.
¡PELIGRO! Cuchillas giratorias. Mantenga manos y pies
a una distancia segura.
PRECAUCIÓ N: Retire el enchufe del
tomacorriente de inmediato si el cable está
dañado o cortado.
No colocar la mano debajo de la barrena.
APAGUE la máquina, espere hasta que se
detenga por completo y retire el enchufe del
tomacorriente antes de realizar alguna
tarea de mantenimiento, limpieza o
reparación.
No colocar la mano enfrente del deflector de descarga.
PRECAUCIÓ N: Use siempre protecciones
para sus ojos y oídos.
No exponga la unidad a la lluvia ni la use en lugares
medos.
Use calzado seguro, resistente y
antideslizante.
¡PELIGRO! Riesgos de descargas eléctricas.
¡PELIGRO! Pueden ser lanzados objetos a
gran velocidad cuando el motor está en
funcionamiento. No pase delante de la
máquina cuando está funcionando.
No usar en la lluvia. No usar durante tormentas
eléctricas.
Mantenga a las personas que se
encuentran en el lugar a una distancia
segura.
PARA REDUCIR EL RIESGO DE LESIONES: Antes
de utilizar este producto, cerciórese de que todos
los usuarios lean y comprendan las instrucciones
de seguridad y la demás información incluida
en este manual.
PRECAUCIÓ N: Use protección auditiva apropiada
mientras trabaja. En ciertas condiciones y con cierta
duración de uso, el ruido generado por este producto
puede contribuir a la pérdida de la audición.
Guarde estas instrucciones y revíselas con frecuencia
antes de usar la herramienta y para impartirlas a otros.
ADVERTENCIA: Al utilizar aparatos eléctricos,
se recomienda respetar siempre las precauciones
de seguridad básicas que se detallan a continuación,
a fin de reducir riesgos de incendios, descargas
eléctricas y lesiones personales.
LEA TODAS LAS INSTRUCCIONES
ADVERTENCIAS DE SEGURIDAD IMPORTANTES
NORMAS GENERALES DE SEGURIDAD
Desconecte la batería del dispositivo antes de realizar ajustes,
cambiar accesorios o guardar el dispositivo. Dichas medidas
de seguridad preventivas reducen el riesgo de encender el
aparato accidentalmente.
Recargue solo con el cargador especificado por el fabricante.
Un cargador que sea adecuado para un tipo de batería puede
crear un riesgo de incendio cuando se usa con otra batería.
Use electrodomésticos solo con paquetes de baterías
específicamente designados. El uso de cualquier otra batería
puede crear un riesgo de lesiones e incendios.
Cuando no use la batería, manténgala alejada de otros objetos
metálicos, como clips de papel, monedas, llaves, clavos, tornillos
u otros objetos metálicos pequeños, que pueden hacer una
conexión de un terminal a otro. El cortocircuito de los terminales
de la batería puede causar quemaduras o un incendio.
En condiciones abusivas, se puede expulsar líquido de la
batería; evitar el contacto. Si se produce un contacto accidental,
enjuague con agua. Si el líquido entra en contacto con los ojos,
busque ayuda médica adicional. El quido expulsado de la
batería puede causar irritación o quemaduras.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54

EarthWise SN74022 Le manuel du propriétaire

Catégorie
Tondeuses à gazon
Taper
Le manuel du propriétaire