Cub Cadet 47RIAHA7010 Manuel utilisateur

Marque: Cub Cadet

Modèle: 47RIAHA7010

Catégorie: Tondeuses à gazon

Taper: Manuel utilisateur

Important Safe Operation Practices • Assembly • Operation • Service and Maintenance • Troubleshooting

OPERATOR’S MANUAL

WARNING

California Proposition 65

Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to State of

California to cause cancer and birth defects or other reproductive harm.

Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of

California to cause cancer and reproductive harm. Wash hands after handling.

WARNING

Read and follow all safety rules and instructions in this manual before attempting to operate this machine.

Failure to comply with these instructions may result in personal injury.

Record Product Information

Before setting up and operating your new equipment,

please locate the model plate on the equipment and

record the information in the provided area to the right.

You can locate the model plate by lifting up the seat

and looking under the seat pan. This information will be

necessary, should you seek technical support via our web

site or with your local authorized service dealer.

MODEL NUMBER

SERIAL NUMBER

Form No. 769-22033A

(October 21, 2019)

Important Safe Operation Practices ..................... 2

Assembly .................................................................. 8

Operation ................................................................12

Service and Maintenance ......................................18

Troubleshooting .................................................... 26

Parts/Warranty .............. See Separate Supplement

Table of Contents

NOTE: This Operator’s Manual covers several models. Features may vary by model. Not all features in this manual are applicable to all

models and the model depicted may differ from yours.

Zero-Turn Tractor

Lapbar Drive Control Levers

SAFE OPERATIONS PRACTICES

General Information

1. Read, understand, and follow all instructions on the tractor

and in the manual(s) before attempting to assemble and

operate. Keep this manual in a safe place for future and

regular reference and for ordering replacement parts.

2. Be familiar with all controls and their proper operation.

Know how to stop the tractor and disengage them quickly.

3. Never allow children under 14 years of age to operate this

tractor. Children 14 and over should read and understand

the instructions and safe operation practices in this manual

and on the tractor and should be trained and supervised by

an adult.

4. Never allow adults to operate this tractor without proper

instruction.

5. If situations occur which are not covered in this manual, use

care and good judgment. Contact your customer service

representative for assistance.

6. According to the U.S. Consumer Products Safety Commission

(CPSC) and the U.S. Environmental Protection Agency (EPA),

this product has an estimated useful life of seven (7) years,

under ordinary use conditions. At the end of its useful life,

have the product inspected annually to ensure all mechanical

and safety systems are operating properly, safely, and are

not worn excessively. Failure to do so may result in accident,

injury, or death.

Preparation Before Operating

1. Thoroughly inspect the area where the tractor is to be

used. Remove all stones, sticks, wire, bones, toys, and other

foreign objects which could be picked up and thrown by the

blade(s). Thrown objects can cause serious personal injury.

2. To help avoid blade contact or a thrown object injury, keep

helpers at least 75 feet (23 meters) from the tractor while it

is in operation. Keep bystanders, children and pets inside

during operation. Stop tractor if anyone enters the area.

3. Be aware of the tractor discharge direction and do not point

it at anyone.

4. Always wear safety glasses or safety goggles during operation

and while performing an adjustment or repair to protect your

eyes. Thrown objects which ricochet can cause serious injury to

the eyes.

5. Wear sturdy, rough-soled work shoes and close-fitting slacks

and shirts. Loose fitting clothes, jewelry and long hair can be

caught in moving parts. Never operate this tractor in bare feet

or sandals.

6. Never over fill fuel tank. Fill tank to no more than ½”

(13mm) below bottom of filler neck to allow space for fuel

expansion.

7. Replace gasoline cap and tighten securely.

8. Use only accessories and attachments approved for this

tractor by the tractor manufacturer. Read, understand and

follow all instructions provided with the approved accessory

or attachment.

Operator Protective System (OPS)

1. This tractor is equipped with an Operator Protective

System (OPS), which includes:

a. Roll Over Protective Structure (ROPS) of the fixed or

folding configuration.

b. Seat belt assembly with retractable function.

2. ROPS are structures designed to provide a crush-resistant

space for the operator when properly seat-belted within

the designated seating area of the tractor in the event of

a tractor tip-over or rollover. ROPS shall be used in their

fully upright and locked configurations except in those

circumstances whereby they need to be momentarily folded

down to avoid contact with items such as tree limbs, clothes

lines, guy wires, utility poles, buildings, etc. At other times

and conditions, ROPS shall be in their fully upright and

locked configurations.

3. Seat belts shall be used and shall always be properly fastened

about the operator’s waist, except when the ROPS are:

a. Not properly installed and/or not properly secured

onto the tractor.

b. Damaged in such manner that the ROPS structural

integrity has been compromised.

c. Not in their fully upright and locked position.

4. Seat belts are attached to the movable portion of the seat

when suspension seats are utilized, and therefore the seat-

mounting base must be secured to its pivot means and the

pivot means secured/latched to the frame of the tractor.

Seat belts are attached to the seat or the frame of the tractor

when non-suspension (standard) seat is provided, however,

if a suspension kit is added to a seat, the seat belt must be

attached to the movable portion of the seat or suspension

mechanism, the seat-mounting base must be secured to its

pivot means, and the pivot means be secured/latched to the

frame of the tractor.

DANGER

If ROPS are folded down or missing, seat belts shall not be

fastened. A worn or damaged seat belt assembly or a dam-

aged ROPS must be replaced prior to operator use of the

tractor.

WARNING

This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or

property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine.

Failure to comply with these instructions may result in personal injury. When you see this symbol. HEED ITS WARNING!

DANGER

This machine was built to be operated according to the safe operation practices in this manual. As with any type of power

equipment, carelessness or error on the part of the operator can result in serious injury. This machine is capable of amputating

hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death.

SAFE OPERATIONS PRACTICES

8. Disengage blade(s), move the drive control levers fully

outward to set the parking brake, stop engine and wait until

the blade(s) come to a complete stop before removing grass

catcher, emptying grass, unclogging chute, removing any

grass or debris, or making any adjustments.

9. Your tractor is designed to cut normal residential grass of

a height no more than 10” (25cm). Do not attempt to mow

through unusually tall, dry grass (e.g. pasture) or piles of dry

leaves. Dry grass or leaves may contact the engine exhaust and/

or build up on the tractor deck presenting a potential fire hazard.

10. Back up slowly. Always look down and behind before and

while backing to avoid a back-over accident.

11. Never carry passengers.

12. Stay at least 10 feet (3 meters) from drop-offs, ditches,

embankments or the edge of water. The tractor could

suddenly turn over if a wheel is over the edge of a cliff, ditch,

or if an edge caves in.

13. A missing or damaged chute deflector can cause blade

contact or thrown object injuries.

14. Do not operate the tractor without the chute deflector or

entire grass catcher in its proper place.

15. Use extra care with grass catchers or other attachments.

These can change the stability of the tractor. Always follow

the attachment manufacturer’s instructions.

16. Stop the blade(s) when crossing gravel drives, walks, or

roads and while not cutting grass.

17. Watch for traffic when operating near or crossing roadways.

This tractor is not intended for use on any public roadway.

18. Mow only in daylight or good artificial light.

19. Do not operate the tractor while under the influence of

alcohol or drugs.

20. Slow down before turning. Operate the tractor smoothly.

Avoid erratic operation and excessive speed.

21. The muffler and engine become very hot and can cause

serious burn injuries. Do not touch. Allow the tractor to cool

for five minutes before attempting any service.

22. Never run an engine indoors or in a poorly ventilated area.

Engine exhaust contains carbon monoxide, an odorless, and

deadly gas.

Children

1. Tragic accidents can occur if the operator is not alert to the

presence of children. Children are often attracted to the

tractor and the mowing activity. They do not understand

the dangers. Never assume that children will remain where

you last saw them.

2. Keep bystanders, children and pets inside during operation

under the watchful care of a responsible adult other than

the operator. Stop tractor if anyone enters the area.

3. Never carry children, even with the blade(s) shut off. They

may fall off and be seriously injured or interfere with safe

tractor operation. Children who have been given rides in the

past could suddenly appear in the mowing area for another

ride and be run over or backed over by the tractor.

4. Be alert and turn tractor off if a child or bystander enters the

area.

5. To avoid back-over accidents, always look behind and down

for small children.

6. Use extreme care when approaching blind corners,

doorways, shrubs, trees or other objects that may block your

vision of a child who may run into the path of the tractor.

5. The ROPS extends above and behind the operator position,

and therefore the operator must be aware of potential

contact of the ROPS with items such as tree limbs, buildings,

doorways, clothes lines, utility/guy wires, etc., that could

cause the tractor to tip-over or rollover. Use caution in (or

avoid) areas where the ROPS could come in contact with any

structures, trees, etc.

6. A brush guard or canopy may contact/deflect tree limbs,

buildings, doorways, clothes lines, utility/guy wires, etc. that

otherwise would come in contact with the ROPS. Contact

of the ROPS and/or canopy with such items may create

hazardous conditions whereby the tractor could experience

a tip-over or roll-over.

7. The ROPS and seat belt are integral parts of this tractor and

should not be tampered with, modified in any manner, or

removed.

8. Inspect the ROPS and seat belt assemblies per the

maintenance schedule shown in this manual for damage

or loose hardware. Replace all components that are loose,

damaged or not functioning properly with authorized

replacement parts.

9. Failure to use the seat belt properly could result in serious

injury or death if an accidental overturn occurs. For the

ROPS in the full up position to be effective, the seat belt

must be securely fastened around the operator at all times

when the operator is on the tractor. The tractor operator

coming in contact with the ROPS during a tip-over or

rollover could cause serious injury or death.

10. The ROPS will not prevent tractor from tip-overs or roll-

overs.

11. Do not assume ROPS will protect you in a tip-over or roll-

over. Injuries may still occur.

Operating

1. Data indicates that operators, age 65 years and above, are

involved in a large percentage of riding tractor-related

injuries. These operators should evaluate their ability

to operate the riding tractor safely enough to protect

themselves and others from serious injury.

2. Disengage blade(s) and move the drive control levers fully

outward to set the parking brake before attempting to start the

engine.

3. Do not put hands or feet near rotating parts or under the

cutting deck. Contact with the blade(s) can amputate hands

and feet.

4. Watch for holes, ruts, bumps, rocks, or other hidden objects.

Uneven terrain could overturn the tractor. Tall grass can hide

obstacles.

5. Plan your mowing pattern to avoid discharge of material

toward roads, sidewalks, helpers and the like. Avoid

discharging material against a wall or obstruction which

may cause discharged material to ricochet back toward the

operator.

6. Check overhead clearances carefully before driving under

low hanging tree branches, wires, door openings etc., where

the operator may be struck or pulled from the tractor, which

could result in serious injury.

7. Never leave a running tractor unattended. Always turn off

blade(s), move drive control levers fully outward into park

position, stop engine and remove key before dismounting.

SAFE OPERATIONS PRACTICES

7. Never allow children under 14 years of age to operate this

tractor. Children 14 and over should read and understand

the instructions and safe operation practices in this manual

and on the tractor and should be trained and supervised by

an adult.

8. Do not allow any child to joy ride on the tractor. The tractor

is not a toy or a go-cart. Warn your children that the tractor

can be dangerous and they must stay away from it at all

times.

9. Keep children away from hot or running engines. They can

suffer burns from a hot muffler.

10. Remove key when tractor is unattended to prevent

unauthorized operation. Make certain the key is inaccessible

to small children.

Slope Operation for Lapbar Zero-Turn Tractors

1. Slopes are a major factor related to loss of control and tip-

over accidents which can result in severe injury or death. All

slopes require extra caution. If you cannot back up the slope

or if you feel uneasy on it, do not mow it.

2. For your safety, measure any slope before using the tractor

on the sloped area. Use a slope measuring device in addition

to the slope gauge included as part of this manual to

measure slopes before operating this tractor on a sloped

or hilly area. Smart phone applications can be also utilized

to measure slopes. If the slope is greater than 15 degrees as

shown on the slope gauge or a slope measuring device, do

not operate this tractor on that area or serious injury could

result.

3. Do not mow on slopes greater than 15 degrees (25%).

4. Do not mow up or down slopes, only mow across slopes

that are less than 15 degrees (25%). Use low speeds and

avoid sudden turns.

5. Do not mow on wet grass. Reduced traction could cause

sliding or a loss of control.

6. Do not operate tractor under any conditions where traction,

steering or stability is in question. Tires could slide even if

the wheels are stopped.

7. Avoid starting and stopping on slopes. Avoid making

sudden changes in speed or direction. Make turns slowly

and gradually.

8. Use extra care while operating tractor with grass catcher

or other attachment(s). They can affect the stability of the

tractor. Do not use grass catcher on slopes greater than 10

degrees (17%).

9. Do not try to stabilize the tractor by putting your foot on the

ground.

10. Keep all movement on the slopes slow and gradual. Do

not make sudden changes in speed or direction. Rapid

acceleration could cause the front of the tractor to lift and

rapidly roll over backwards, which could cause serious injury

or death.

Fire & Fuel

1. To avoid personal injury or property damage use extreme

care in handling gasoline. Gasoline is extremely flammable

and the vapors are explosive. Serious personal injury can

occur when gasoline is spilled on yourself or your clothes

which can ignite. Wash your skin and change clothes

immediately.

2. Extinguish all cigarettes, cigars, pipes and other sources of

ignition.

3. Use only an approved gasoline container.

4. Never remove gas cap or add fuel while the engine is hot or

running. Allow engine to cool at least five minutes before

refueling.

5. Never fuel tractor indoors.

6. Never store the tractor or fuel container inside where there

is an open flame, spark or pilot light as on a water heater,

space heater, furnace, clothes dryer or other gas appliances.

7. If gasoline is spilled, wipe it off the engine and equipment.

Clean up oil or fuel spillage and remove any fuel soaked

debris. Move tractor to another area. Wait 5 minutes before

starting the engine.

8. To reduce fire hazards, keep tractor free of grass, leaves, or

other debris build-up. Follow the “Post-Operation Tractor

Care” instructions in the Service and Maintenance section.

9. Your tractor is designed to cut normal residential grass of

a height no more than 10” (25cm). Do not attempt to mow

through unusually tall, dry grass (e.g., pasture) or piles of dry

leaves. Dry grass or leaves may contact the engine exhaust

and/or build up on the tractor deck presenting a potential

fire hazard.

10. Never over fill fuel tank. Fill tank to no more than ½” below

bottom of filler neck to allow space for fuel expansion.

11. Replace gasoline cap and tighten securely. Do not operate

without fuel cap in place.

12. Allow a tractor to cool at least five minutes before fueling or

storing.

13. Never fill containers inside a vehicle or on a truck or trailer

bed with a plastic liner. Always place containers on the

ground away from your vehicle before filling.

14. When practical, remove gas-powered equipment from

the truck or trailer and refuel it on the ground. If this is not

possible, then refuel such equipment on a trailer with a

portable container, rather than from a gasoline dispenser

nozzle.

15. Keep the nozzle in contact with the rim of the fuel tank or

container opening at all times until fueling is complete. Do

not use a nozzle lock-open device.

Hauling

1. Use properly secured full width ramps for loading and

unloading a tractor for transport.

2. Use extra care when loading or unloading the tractor into a

trailer or truck. This tractor should not be driven up or down

ramp(s), because the tractor could tip over, causing serious

personal injury. The tractor must be pushed manually on

ramp(s) to load or unload properly.

3. Raise the deck to the highest position for loading clearance.

Towing with your Lapbar Zero-Turn Tractors

1. Do not tow a load that exceeds 250 lbs (113 kg) rolling

weight and never exceed 50 lbs (22 kg) tongue weight.

2. Do not attach towed equipment except at the hitch point of

the tractor.

3. Never allow children or others in or on towed equipment.

4. Do not tow on slopes greater than 5 degrees (9%). On

slopes, the weight of the towed equipment may cause loss

of traction and loss of control and/or the ability to stop.

5. Always use extra caution when towing with a tractor

capable of making tight turns (e.g. “zero-turn” ride-on

tractor). Make wide turns to avoid jack-knifing.

SAFE OPERATIONS PRACTICES

6. Travel slowly and allow extra distance to stop.

Service

1. Keep machine in good working order. Do not use the tractor

until worn or damaged parts are replaced.

2. To avoid serious injury or death, do not modify engine in

any way. Tampering with the governor setting can lead to

a runaway engine and cause it to operate at unsafe speeds.

Never tamper with factory setting of engine governor. Do

not change the engine governor settings or over-speed the

engine. The governor controls the maximum safe operating

speed of the engine.

3. Tractor blades are sharp. Wrap the blade or wear gloves, and

use extra caution when servicing them.

4. Tractors with hydraulic pumps, hoses or motors; and/or

diesel injections systems have fluid systems under pressure.

Fluid escaping under pressure may have sufficient force to

penetrate skin and cause serious injury. If fluid is injected

into the skin, seek immediate medical attention. Keep

body and hands away from pin holes or nozzles that eject

fluid under high pressure. If a leak occurs, have the tractor

immediately serviced by an authorized dealer.

5. Before cleaning, repairing, or inspecting, make certain

the blade(s) and all moving parts have stopped. Turn off

the engine, remove the key, and disconnect the spark

plug wire(s) and ground against the engine to prevent

unintended starting.

6. Check to make sure the blades come to complete stop in

not more than (5) five seconds after disengaging the blade

disengagement control per the schedule shown on the

Maintenance Schedule chart in the Service and Maintenance

section of this manual. Measure the stopping time with a

stop watch. If the blades do not stop completely in less than

five seconds, your tractor should be serviced professionally

by an authorized dealer.

7. Check the safety interlock system for proper function per

the schedule shown on the Maintenance Schedule chart in

the Service and Maintenance section of this manual. If the

safety interlock system does not function properly, have

your tractor serviced professionally by an authorized dealer.

8. Never tamper with the safety interlock system or other

safety devices. Check their proper operation regularly.

9. Check the blade(s) and engine mounting bolt torque in

accordance to Maintenance Schedule chart in this manual.

Also, visually inspect blade(s) for damage (e.g., excessive

wear, bent, cracked). Replace the blade(s) with the original

equipment manufacturer’s (O.E.M.) blade(s) only.

10. Use of service parts which do not meet the original

equipment specifications may lead to improper

performance and compromise safety.

11. Keep all nuts, bolts, and screws tight to be sure the

equipment is in safe working condition. Review the

Maintenance Schedule chart in this manual for service

interval information.

12. After striking a foreign object, stop the engine, disconnect

the spark plug wire(s) and ground against the engine.

Thoroughly inspect the tractor for any damage. Repair the

damage before starting and operating.

13. Never attempt to make adjustments or repairs to the tractor

while the engine is running.

14. Grass catcher components and the chute deflector are

subject to wear and damage which could expose moving

parts or allow objects to be thrown. Frequently check

components and replace immediately with original

equipment manufacturer’s (O.E.M.) parts only.

15. Maintain or replace safety and instruction labels, as

necessary.

16. Observe proper disposal laws and regulations for gas, oil,

etc. to protect the environment.

Notice Regarding Emissions

Engines which are certified to comply with California and

federal EPA emission regulations for SORE (Small Off Road

Equipment) are certified to operate on regular unleaded

gasoline, and may include the following emission control

systems: Engine Modification (EM) and Three Way Catalyst

(TWC) if so equipped.

When required, models are equipped with low permeation fuel

lines and fuel tanks for evaporative emission control. California

models may also include a carbon canister. Please contact

Customer Support for information regarding the evaporative

emission control configuration for your model.

Spark Arrestor

WARNING

This tractor is equipped with an internal combustion engine

and should not be used on or near any unimproved forest-

covered, brush-covered or grass-covered land unless the

engine’s exhaust system is equipped with a spark arrestor

meeting applicable local or state laws (if any).

If a spark arrestor is used, it should be maintained in effective

working order by the operator. In the State of California the

above is required by law (Section 4442 of the California Public

Resources Code). Other states may have similar laws. Federal

laws apply on federal lands.

A spark arrestor for the muffler is available through your

nearest engine authorized service dealer or contact the service

department, P.O. Box 361131 Cleveland, Ohio 44136-0019.

SAFE OPERATIONS PRACTICES

Symbol Description

OPESymbol.com

WARNING  READ OPERATOR’S MANUAL

Read, understand and follow all the safety rules and instructions in the

manual(s) and on the tractor before attempting to operate this tractor.

Failure to comply with this information may result in personal injury or

death. Keep this manual in a safe location for future and regular reference.

Using a Smart Phone, scan the QR code symbol to learn more information

concerning the warnings contained on this tractor. You can also go to www.

OPESymbol.com for more information.

WARNING  AVOID THROWN OBJECTS INJURY

Keep helpers at least 75’ (23 meters) from machine during operation.

Remove all stones, sticks, wire, bones, toys, and other foreign objects which

could be picked up and thrown by the blade(s). Do not operate the tractor

without the discharge cover or entire grass catcher in its proper place.

WARNING – AVOID CHILD BACKOVER/RUNOVER/BLADE INJURY

To avoid back-over accidents, always look behind and down for small children.

Never carry children, even with the blade(s) shut off. Keep bystanders, children

and pets inside during operation under the watchful care of a responsible

adult other than the operator. Stop tractor if anyone enters the area.

> 15

< 15

10ft (3m)

WARNING – AVOID TIP-OVER/ROLL-OVER INJURY

Do not operate machine on a slope greater than 15° (25%). Do not mow

up or down slopes, only mow across slopes that are less than 15 degrees

(25%). Use low speeds and avoid sudden turns on slopes. Stay at least 10

feet (3 meters) from drop-offs, ditches, embankments or the edge of water.

>10in (25cm)

WARNING – AVOID FIRES

Your tractor is designed to cut normal residential grass of a height no more

than 10” (25cm). Do not attempt to mow through unusually tall, dry grass

(e.g., pasture) or piles of dry leaves. Allow a tractor to cool at least five minutes

before fueling or storing inside an enclosed garage or storage shed.

WARNING – AVOID AMPUTATION INJURY

Do not put hands or feet near or under the cutting deck. Contact with the

blade(s) can amputate hands and feet.

WARNING – AVOID AMPUTATION INJURY

Do not put hands or feet near rotating parts or under the cutting deck.

Contact with the blade(s) can amputate hands and feet. Ensure that all

safety devices (guards, shields, switches, etc.) are in place and working.

Belt and/or blade spindle contact can crush or injure body parts.

WARNING – AVOID CRUSH/PINCH POINT INJURY

Read, understand and follow all the safety rules and instructions in the

manual(s) and on the tractor before attempting to service this tractor. For

foot lift models only, the deck lift system is spring-assisted and under

tension. Always use the provided multi-tool to secure the lift system in the

locked position before attempting to remove the mower deck.

WARNING – REMOVE KEY

Always turn off blade(s), move the drive control levers outward into park

position, stop engine and remove key before dismounting. If you are leaving

the tractor unattended, always remove the key to prevent unauthorized use by

children or others.

<5 0lb

(22k g)

<250 lb (113kg)

WARNING – AVOID TOWING RELATED INJURY

Do not tow a load that exceeds 250 lbs (113 kg) rolling weight and never exceed

50 lbs (22 kg) tongue weight. Never allow children or others in or on towed

equipment. Do not tow on slopes greater than 5 degrees (9%). On slopes, the

weight of the towed equipment may cause loss of traction,loss of control and/or

loss of the ability to stop. Travel slowly and allow extra distance to stop.

WARNING

Your Responsibility — Restrict the use of this power machine to persons who read, understand and follow the warnings and

instructions in this manual and on the machine.

SAVE THESE INSTRUCTIONS!

Safety Symbols

This page depicts and describes safety symbols that MAY APPEAR on this product.

(OK) (TOO STEEP)

USE THIS SLOPE GAUGE TO DETERMINE

IF A SLOPE IS TOO STEEP FOR SAFE OPERATION!

To check the slope, proceed as follows:

1. Remove this page and fold along the dashed line.

2. Locate a vertical object on or behind the slope (e.g. a pole, building, fence, tree, etc.)

3. Align either side of the slope gauge with the object (See Figure 1 and Figure 2 ).

4. Adjust gauge up or down until the left corner touches the slope (See Figure 1 and Figure 2).

5. If there is a gap below the gauge, the slope is too steep for safe operation (See Figure 2 above).

15°/25% dashed line

Slope Gauge

Figure 2Figure 1

15°/25% Slope

15°/25%

Slope

WARNING! Slopes are a major factor related to tip-over and roll-over accidents which can result in severe injury or death.

Do not operate machine on slopes in excess of 15 degrees. All slopes require extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it.

ASSEMBLY

Note: This Operator’s Manual covers several models. Tractor features may vary by

model. Not all features in this manual are applicable to all tractor models and the

tractor depicted may differ from yours.

Note: All references in this manual to the left or right side and front or back of the

tractor are from the operating position only. Exceptions, if any, will be specified.

Preparation

Manually Move the Tractor

1. To engage the

transmission bypass

rods, pull the rod back

(a) and into lower

section of “J” slot.

Repeat on opposite

side. See Figure 1.

2. After moving tractor,

reverse step one to

disengage the bypass

rods.

Install Hitch (If necessary)

1. Locate Hitch (a) and

install on the rear of the

frame using the two

hex washer screws (b)

provided. See Figure 2.

Note: Hitch and hex

washer screws will be in

the hardware pack.

Roll Over Protective

System (ROPS)

Refer to Figure 3 and the

following descriptions and uses for the

three (3) positions for the Upper ROPS.

• TRANSPORT: Only to be used when

transporting the tractor or when they

need to be momentarily folded-down

to avoid contact with items such as

tree limbs, clothes lines, guy wires,

utility poles, buildings, etc.

• TRANSPORT WITH BAGGER:

Allows for the ROPS to be lowered

for situations outlined for the

TRANSPORT position when the tractor

is equipped with a bagger.

• OPERATION: The ROPS should

always be in this position when

operating unless the situations

involved outlined in the TRANSPORT

and TRANSPORT WITH BAGGER

descriptions arise.

(a)

(b)

Figure 1

(b)

(a)

(b)

Figure 2

Transport Position

Transport with

Bagger Position

Operation Position

Upper ROPS Positions

Figure 3

To change the position of the ROPS:

1. Pull slightly up on the ROPS to relieve

any tension on the locking pin (a)

and rotate the locking pin (a) from

the LOCKED (b) position into the

ADJUSTMENT (c) position. Repeat the

procedure for the locking pin on the

opposite side. See Figure 4.

2. Move the ROPS into the desired

position. See Figure 5.

Note: The three positions are TRANSPORT

(a) position, TRANSPORT WITH BAGGER

(b) position and into the OPERATION (c)

position.

3. Rotate both locking pins into the LOCKED

position. Move the upper ROPS slightly

until the locking pins settle, engaged in

the LOCKED position.

Note: See properly seated (fully engaged)

ROPS pin in Figure 6.

DANGER

Always verify that both right and left

locking pins of the ROPS are settled and

fully engaged all the way through the

hinge assembly so that each locking pin is

visible on the inside face. Failure to fully

lock each locking pin may result in serious

injury or death.

Install Operator’s Seat (If Necesarry)

1. Cut any straps securing

the seat assembly to

the tractor. Remove all

packing material.

Note: Be careful not

to cut the seat wiring

harness.

2. Install the seat onto

the seat pan (b) using

flange lock nuts (a). See

Figure 7.

3. If necessary, securely

connect the seat switch

wiring harness (a) to

the seat switch (b).

See Figure 8. Secure

excess wire away from

pinch points before

continuing.

Note: Tractor will not

operate without the

seat switch wiring

harness connected.

(c)

(b)

(a)

Figure 4

(a)

(b)

(c)

Figure 5

Figure 6

(a)

(b)

(a)

Figure 7

(a)

(b)

(a)

(b)

Figure 8

ASSEMBLY

Position Lapbar Drive Control Levers

The lapbar drive control levers can be adjusted up/down and forward/backward for

the operator’s comfort. Three height positions are available and/or levers can be

rotated forward or rearward using the knob.

To adjust the lapbar drive control lever height, proceed as follows:

1. Remove the two carriage

screws (a) and two flange lock

nuts (b) that secure the lapbar

drive control lever (c) to the

upper handle adjuster (d). See

Figure 9.

Note: The multi-tool (if

equipped) can be used to make

this adjustment.

2. Move the lapbar drive control lever

into one of the three available

heights and secure in place with

the carriage screws and flange

lock nuts. See Figure 9.

To adjust the lapbar drive control levers forward/rearward, proceed as follows:

1. Rotate the knob (a) counter-

clockwise to loosen the knob

(a). See Figure 10.

2. Lift and rotate the lapbar drive

control lever into the desired

position.

3. Rotate the knob clockwise to

secure the lapbar drive control

lever into position. See Figure 10.

4. If the lapbars do not line

up after making the knob

adjustment, loosen nuts (b),

align lapbars and retighten

nuts. Once this fine adjustment

is made, the lapbars will align

when using the knob adjustment. See Figure 9.

Lower Deck Discharge Chute Deflector

WARNING

Never operate the mower deck without the chute deflector installed and in

the down position.

1. The chute is shipped attached and with a stop bracket holding the chute

upright. The stop bracket must be removed prior

to operating the tractor. See Figure 11.

2. Holding the chute deflector fully upward, remove

the stop bracket:

a. Grasp the bracket (a) from behind the

chute on top of the deck.

b. Lift up slightly to free the bracket from the

notch (b).

c. Pull back to fully remove the bracket.

Setting Deck Wheels

Note: The deck wheels are an anti-scalp feature of the

deck and are not designed to support the weight of the

cutting deck.

1. Move the tractor to a level surface, preferably

pavement.

2. Check tire pressure, adjust, if necessary. See tire side wall for proper tire

pressure.

(b)

(a)

(c)

(d)

Figure 9

(a)

Figure 10

Figure 11

3. Make sure the deck is level side-to-side and properly pitched. See the Service

& Maintenance section for deck leveling information and instructions.

4. Place knob in the desired mowing height position and lower the deck.

5. Check the deck wheels for contact or excessive clearance with the surface

below.

Note: The deck wheels should have between ¼” (6.35mm) and ½” (12.7mm)

clearance above the ground.

6. Remove the lock nut (a)

securing one of the front

gauge wheels to the deck.

Remove the shoulder

screw (b), tube spacer (c)

and shoulder spacer (e) to

remove the wheel (d) See

Figure 12.

7. Line up the gauge wheel

with the tube spacer

through the center, and

the shoulder spacer on

the shorter side hub of the

gauge wheel, and position

the assembly inside the

brackets at the desired

height.

Note: Allow a ⁄⁄” (6.35-12.7 mm)clearance between the ground and gauge

wheel.

8. Insert the shoulder screw into the chosen index hole on the front gauge

wheel bracket.

Note: On the left side and right side deck gauge

wheels, the shoulder screw must be installed from

the outside of the tractor inward, through the

square hole on the bracket. On center deck gauge

wheels (if equipped) the shoulder screw side of the

assembly can be installed from either direction. See

Figure 13.

9. Secure with the lock nut previously

removed.

Battery Information

WARNING

California PROPOSITION 65 WARNING: Battery posts, terminals,

and related accessories contain lead and lead compounds, chemicals

known to the State of California to cause cancer and reproductive harm.

Wash hands after handling.

WARNING

Should battery acid accidentally splatter into the eyes or onto the skin,

rinse the affected area immediately with clean cold water. Seek prompt

medical attention.

If acid spills on clothing, first dilute it with clean water, then neutralize

with a solution of ammonia/water or baking soda/water.

NEVER connect (or disconnect) battery charger clips to the battery while

the charger is turned on, as it can cause sparks.

Keep all sources of ignition (cigarettes, matches, lighters) away from the

battery. The gas generated during charging can be combustible.

As a further precaution, only charge the battery in a well ventilated area.

Always shield eyes and protect skin and clothing when working near

batteries.

Batteries contain sulfuric acid and may emit explosive gases. Use extreme

caution when handling batteries. Keep batteries out of the reach of

children.

(a)

(b)

(c)

(d)

(e)

Figure 12

Outer bracket

Inner bracket

Figure 13

ASSEMBLY

CAUTION

When attaching battery cables, always connect the POSITIVE (Red) wire to

terminal first, followed by the NEGATIVE (Black) wire.

Note: The positive battery terminal is marked Pos. (+). The negative battery terminal is

marked Neg. (–).

Connecting Battery Cables

WARNING

Always connect the positive lead to the battery before connecting the

negative lead. This will prevent sparking or possible injury from an

electrical short caused by contacting the tractor body with tools being

used to connect the cables.

For shipping reasons the factory may leave both battery cables disconnected from

the terminals. To connect the battery cables, proceed as follows:

1. If present, remove the plastic cover from the positive battery terminal.

Attach the red connector to the positive battery terminal (+) using the bolt

(a) and hex nut (b). See Figure 14.

2. If present, remove

the plastic cover from

the negative battery

terminal and attach

the black cable to

the negative battery

terminal (–) with the

bolt (a) and hex nut

(b). See Figure 14.

3. Position the red

rubber boot (c) over

the positive battery

terminal (+) to

help protect it from

corrosion. See Figure 14.

Note: If the battery is put into service after date shown on top/side of battery,

charge the battery as instructed in the Service & Maintenance section, prior to

operating.

Battery Maintenance

• The battery is filled with battery acid and then sealed at the factory.

However, even a “maintenance free” battery requires some maintenance to

ensure its proper life cycle.

• Spray the terminals and exposed wire with a battery terminal sealer, or coat

the terminals with a thin coat of grease or petroleum jelly, to protect against

corrosion.

• Always keep the battery cables and terminals clean and free of corrosion.

• Avoid tipping. Even a sealed battery will leak electrolyte when tipped.

Battery Storage

• When storing the tractor for extended periods, disconnect the negative

battery cable. It is not necessary to remove the battery.

• All batteries discharge during storage. Keep the exterior of the battery clean,

especially the top. A dirty battery will discharge more rapidly.

• The battery must be stored with a full charge. A discharged battery can

freeze sooner than a charged battery. A fully charged battery will store

longer in cold temperatures than hot.

(b)

(a)

(c)

Figure 14

• Recharge the battery before returning to service. Although the tractor may

start, the engine charging system may not fully recharge the battery.

Battery Removal

WARNING

Battery posts, terminals and related accessories contain lead and lead

compounds. Wash hands after handling.

The battery is located beneath the seat frame. To remove the battery:

1. Remove the hex washer screw (a)

securing the battery hold-down

bracket (b) to the frame. Then flip the

battery hold-down bracket (b) up to

free the battery. See Figure 15.

2. Remove the hex cap screw and sems

nut securing the black negative

battery lead to the negative battery

post (marked NEG). Move the cable

away from the negative battery post.

3. Remove the hex cap screw and sems

nut securing the red positive battery

lead to the positive battery post

(marked POS).

4. Carefully lift the battery out of the

tractor.

5. Install the battery by repeating the above steps in the reverse order.

Charging the Battery

Test and, if necessary, recharge the battery after the tractor has been stored for a

period of time.

• A voltmeter

or load tester

should read

12.6 volts (DC)

or higher across

the battery

terminals. See

Figure 16.

• Charge the

battery with a

12-volt battery

charger at a MAXIMUM rate of 10 amps.

Operating the Seat Latch

1. Place the lapbar drive

control levers fully out in

the parking brake position.

2. Locate the seat latch at the

rear base of the seat.

3. press downward on the

front tabs to disengage the

seat latch.

4. Rotate the entire seat pan

upward. See Figure 17.

(a)

(b)

Figure 15

Voltmeter

Reading

State of

Charge

Charging

Time

12.7 100% Full Charge

12.4 75% 90 Min.

12.2 50% 180 Min.

12.0 25% 280 Min.

Figure 16

Figure 17

ASSEMBLY

Attaching the Seat Tether (ZT6 Models Only)

ZT6 Models are shipped with the seat folded forward, and the seat tether cable

detached from the seat pan.

1. Locate the seat tether cable. The lower end will be preinstalled on the inner

left side of the frame.

2. Using a 7/16” wrench and a 3/8” wrench remove the shoulder bolt and hex

lock nut from the left side of the seat pan.

3. Install the detached end of seat tether cable onto the seat pan with the

hardware previously removed as

shown in Figure 18:

a. Slide the cable onto the

shoulder bolt previously

removed.

b. Route the shoulder bolt

through the hole from the

inside outward.

c. Secure the cable with the

hex lock nut and torque

to 68-102 in-lbs (8-11.5

N-m).

Adjusting the Seat

1. Push left and hold

the seat adjustment

lever to adjust the

seat position.

2. Slide seat forward or

rearward to desired

position.

3. Release the

adjustment lever.

Ensure seat is locked

into position before

operation. See

Figure 19.

Adjusting the Mechanical Suspension Mechanism (ZT6 Models

Only)

The mechanical suspension

mechanism (if equipped)

incorporates weight/ride

adjustment controls for operators

in the 125 to 275 lb. (57-124 kg)

weight range. Turn the knob on

the front of the seat clockwise to

increase the weight capacity and

counter-clockwise to decrease.

See Figure 20.

Note: The seat base must be

secured by the latch, otherwise, the seat assembly could tilt forward. The Operator

Presence Sensor must be connected to the electrical wiring harness.

Figure 18

Figure 19

Figure 20

OPERATION

Figure 21

Ignition Switch

WARNING

Never leave a running machine unattended. Always disengage PTO,

set parking brake, stop engine and remove key to prevent unintended

starting.

The ignition switch has three positions:

STOP

— The engine and electrical system is turned off.

RUN — The tractor electrical system is energized.

START — The starter motor will turn over the engine. Release the key

immediately when the engine starts.

Note: To prevent accidental starting and/or battery discharge, remove key from the

ignition switch when tractor is not in use.

Transmission Bypass Rods

The transmission bypass rods (one for each RH and LH transmission) are located

on the rear of the tractor, next to the engine.When engaged, the two rods open a

bypass within the hydrostatic transmissions, which allows the tractor to be pushed

short distances by hand. Refer to the Assembly section for additional instructions.

CAUTION

Never tow your tractor. Towing the tractor with the rear wheels on the

ground may cause severe damage to the transmissions.

Note: This Operator’s Manual covers several

models. Tractor features may vary by model. Not

all features in this manual are applicable to all

tractor models and the tractor depicted may differ

from yours.

Note: References to LEFT, RIGHT, FRONT, and REAR

indicate that position on the tractor when facing

forward while seated in the operator’s seat.

Lapbar Drive Control Levers

The RH (Right Hand) and LH (Left Hand) lapbar

drive control levers are located on each side

of the operator’s seat. The hinged levers pivot

outward to permit the operator to sit in the seat, or

dismount. To start the tractors engine, the lapbar

drive control levers must be fully out and in park

position. When the lapbar drive control levers are

fully outward, the parking brake is engaged.

Each drive control lever controls the respective

transmission. Consequently, these levers control

all of the tractors movement. Driving and steering

using these control levers is quite different from

a conventional tractor and will take practice to

master. Refer to Practice Operation section for

further instructions.

Deck Height Index

Each rotation represents a ⁄” (6.35 mm) change

in deck height. Positions range from 1” (2.5 cm) to

4-¾” (12 cm) at the highest point. See 4a and 4b

in Figure 21.

Deck Transport Lock Control

The deck transport lock control is used to lock the deck above its highest cut setting

into transport mode. To engage the deck transport lock control depress the deck

lift pedal (4a) and move the deck transport lock control into its rear position. To

disengage the transport lock and set the deck to its designated cut height, depress

the deck lift pedal and move the deck transport lock control into its front position.

Deck Lift Pedal

The deck lift pedal is located on the front, right corner of the platform. The pedal is

used in conjunction with the deck lift knob to raise and lower the mowing deck. Push

forward on the deck lift pedal, rotate the deck lift knob to the desired height and

release the deck lift pedal.

Deck Lift Knob

The deck lift knob is used in conjunction with the deck lift pedal to raise and lower

the mowing deck. Push forward on the deck lift pedal, rotate the deck lift knob to the

desired height and release the deck lift pedal.

Power Take-Off (PTO)

Electric PTO

The PTO switch operates the electric PTO clutch mounted on the

bottom of the engine crankshaft. Pull the switch knob upward

to engage the PTO clutch, or push the knob downward to

disengage the clutch.

The PTO switch must be in the “OFF” position when starting the

engine.

OPERATION

Cup Holder

The cup holder is located on the top of the console.

Storage Tray

The storage tray is located to the rear of the console.

Fuel Tank Cap

Turn the fill cap counter clockwise and pull upward to remove. The fuel cap is tethered

to the tractor to prevent its loss. Do not attempt to remove the cap from the tractor. Fill

tank to ½” (12.7 mm) below the bottom of the filler neck, allowing some space in the

tank for fuel expansion. Do not overfill the tank.

Push the cap downward on the fuel tank fill neck and turn at least two clicks clockwise to

tighten. Always re-install the fuel cap tightly onto the fuel tank after removing.

WARNING

Never fill the fuel tank when the engine is running. If the engine is hot

from recently running, allow to cool for at least five minutes before

refueling. Highly flammable gasoline could splash onto the engine and

cause a fire.

Fuel Gauge

The fuel gauge is located to the left of the seat and provides an indicator of the

current fuel level in the tank.

Hour Meter & LCD Service Minder (If equipped)

The LCD service minder will remind the

operator of maintenance intervals for

changing the engine oil, air filter service,

low engine and low battery warnings.

When the key is rotated out of the STOP

position but is not in the START position, the

LCD service minder & hour meter will briefly

display the battery voltage, followed by the

tractor’s accumulated hours.

Note: When the ignition key is out of the STOP position the hourglass

symbol

is illuminated/blinks to indicate it is recording the hours of tractor operation,

regardless of whether the engine has been started.

Change Oil

The LCD screen will alternate the letters “CHG”, followed by “OIL”, followed by

“SOON”, followed by the meter’s accumulated time. “CHG/OIL/SOON/TIME” will

alternate on the display for 7 minutes after the meter reaches 50 hours. This oil

service minder interval will occur every 50 hours. Before the interval expires,

change the engine oil as instructed in the Engine Operator’s Manual

Low Oil

Note: The low oil pressure function only works if the engine is equipped with an oil

pressure switch.

The LCD screen will alternate the letters “LO” followed by “OIL”, followed by the

meter’s accumulated time, which indicates the engine has low oil pressure. This is

common when starting an engine. The indicator will remain active until the engine

sufficiently builds pressure after starting. If it remains on with the engine at full

speed and after a few minutes of operation, stop the tractor immediately and check

the engine oil level and add as instructed in the Engine Operator’s Manual. If the oil

level is correct and the indicator persists, contact an authorized service dealer.

Low Battery

At startup, the battery voltage will briefly display, then changes to accumulated

hours. The letters “LO” followed by the letters “BATT” will display, followed by

the meter’s accumulated time. “LO/BATT/TIME” is displayed on the LCD when the

voltage drops below 11.5 volts. When this occurs, the battery is in need of a charge

or the engine’s charging system is not generating sufficient amperage. Charge the

battery as instructed in the Product Care section of this manual or have the charging

system checked by your local service dealer.

Air Filter Service

The LCD screen will display the letters “CLN” followed by the letters “AIR”, followed

by “FILT”, followed by the meter’s accumulated time. “CLN/AIR/FILT/TIME” will

alternate on the display for 7 minutes after the meter reaches 25 hours. This air

filter service minder time interval will be every 25 hours. On intervals that are

common with oil service, the oil message will be displayed first followed by the air

filter message.

Throttle/Choke Control Lever or Throttle Control Lever

Note: When set in a given position, a uniform engine speed will be maintained.

Throttle Control Lever (If equipped)

Push the throttle control lever forward to

increase the engine speed. The tractor is

designed to operate with the throttle control

lever at full throttle (FAST) when the tractor is being driven and the tractor deck is

engaged. Pull the throttle control lever rearward to decrease the engine speed.

Throttle/Choke Control Lever (If equipped)

Push the throttle/choke control lever

forward to increase the engine speed. The

tractor is designed to operate with the

throttle/choke control lever at full throttle (FAST) when the tractor is being driven and

the mower deck is engaged. Pull the throttle/choke control lever rearward to decrease the

engine speed. When starting the engine, push the control lever fully forward into the “CHOKE”

position. After starting and warming the engine, move the control handle rearward until

you feel it move past the choke detent. Throttle is not meant to control unit speed, throttle

should remain in high speed while operating blades.

Choke Control (If equipped)

The choke control determines the position of the engine choke.

Pull the knob out to choke the engine; push the knob in to open

the choke.

Multi-Tool

The multi-tool (a) is located on the back

of the right console. The multi-tool

(a) can be used as a deck lift lockout,

adjust the height of the lapbar drive

control levers, drive control lever

stop adjustment and can be used as

a removal tool with the ½” socket

end. See the Service and Maintenance

section for more information on multi-

tool usage. See Figure 22.

Headlights (Not shown)

The headlights are located on the front of the frame. The headlights are ON

whenever the ignition key is rotated out of the STOP position and OFF when the

ignition key is moved to the STOP position.

Seat Adjustment Lever (Not shown)

The seat adjustment lever is located under the seat. The seat adjustment lever

allows for adjustment forward or backward of the operator’s seat. Refer to the

Assembly section for instructions on adjusting the seat position.

Note: If your tractor is not equipped with a seat adjustment lever, it can be adjusted

using the knobs on the underside of the seat. Refer to the Assembly section for

instruction on adjusting the seat.

Operation

Before Operating Your Tractor

• Before operation, refer to Maintenance Schedule chart located in this manual

for regularly scheduled service items.

Figure 22

OPERATION

• This engine is certified to operate only on clean, fresh, unleaded gasoline. Fill

only with clean, fresh, unleaded gasoline with a pump sticker octane rating

of 87 or higher.

• Do not use gasoline left over from the previous season, to minimize gum deposits in

the fuel system.

• Gasohol (up to 10% ethyl alcohol, 90% unleaded gasoline by volume) is an

approved fuel. Other gasoline/alcohol blends are not approved.

• Methyl Tertiary Butyl Ether (MTBE) and unleaded gasoline blends (up to a

maximum of 15% MTBE by volume) are approved fuels. Other gasoline/ether

blends are not approved.

Safety Interlock System

WARNING

Do not operate the tractor if the safety interlock system is malfunctioning.

This system was designed for your safety and protection.

This tractor is equipped with a safety interlock system for the protection of the operator.

If the interlock system should ever malfunction, do not operate the tractor. Contact an

authorized service dealer.

• The safety interlock system prevents the engine from cranking or

starting unless the parking brake is engaged, and the PTO switch is in the

DISENGAGED (OFF) position.

• The engine will automatically shut OFF if the operator leaves the seat before

engaging the parking brake.

• The engine will automatically shut OFF if the operator leaves the tractor’s

seat with the PTO switch in the ENGAGED (ON) position, regardless of

whether the parking brake is engaged.

Checking the Safety Interlock Circuits

Periodically check the safety interlock circuits to ensure they are working properly.

If a safety circuit is not working as designed, contact you Service dealer to have the

tractor inspected. DO NOT operate the tractor if any safety circuit is not functioning

properly. To check the safety circuits, proceed as follows:

1. Pull the PTO upward to the ENGAGED (ON) position. Momentarily turn the

ignition switch to the START position; the engine should not crank.

2. With the tractor running move both lapbar drive control levers fully inward in the

neutral position; then lift upward from the operator’s seat. The engine should stop.

3. With both lapbar drive control levers fully outward in the parking brake

engaged position, engage the PTO. Lift upward from the operator’s seat; the

engine should stop.

Starting the Engine

CAUTION

The operator should be sitting in the tractor seat when starting the engine.

1. Operator should be

sitting in the tractor

seat with the lapbar

drive control levers

fully out and in the

park position. See

Figure 23. Refer to

Practice Operation for

further instructions.

Control Levers Moved

Outward & in the Park Brake Position

Figure 23

2. Make certain the PTO is in the “OFF” position. Move the choke control or throttle/

choke control into the full choke position. Move the throttle control to midway

between its slow and fast positions on models with a separate choke control.

Note: If the engine is warmed up, it may not be necessary to choke the

engine.

3. Turn the key clockwise to the START position. After the engine starts, release

the key. It will return to the RUN position.

CAUTION

Do NOT hold the key in the START position for longer than ten seconds at a

time. Doing so may cause damage to your engine’s electric starter.

4. As the engine warms up, gradually pull the throttle/choke control lever

rearward past the choke detent position or slowly disengage the choke on

models with a separate choke. Do not use the choke position to enrich the

fuel mixture, except as necessary to start the engine.

5. Allow the engine to run for a few minutes at mid-throttle before putting the

engine under load.

6. Observe the hour meter/indicator panel. If the battery indicator light or oil

pressure light come on, immediately stop the engine. Have the tractor inspected

by your authorized service dealer.

Cold Weather Starting

When starting the engine at temperatures near or below freezing, ensure the correct

viscosity motor oil is used in the engine and the battery is fully charged. Start the

engine as follows:

1. Be sure the battery is in good condition. A warm battery has much more

starting capacity than a cold battery.

2. Use fresh winter grade fuel. Winter grade gasoline has higher volatility to

improve starting. Do not use gasoline left over from summer.

3. Follow the previous instruction for Starting the Engine.

Using Jumper Cables To Start Engine

WARNING

Batteries contain sulfuric acid and produce explosive gasses. Make certain

the area is well ventilated, wear gloves and eye protection, and avoid sparks

or flames near the battery.

If the battery charge is not sufficient to crank the engine, recharge the battery. If a

battery charger is unavailable and the tractor must be started, the aid of a booster

battery will be necessary. Connect the booster battery as follows:

1. Connect the end of one cable to the disabled tractor battery’s positive

terminal; then connect the other end of that cable to the booster battery’s

positive terminal.

2. Connect one end of the other cable to the booster battery’s negative

terminal; then connect the other end of that cable to the frame of the

disabled tractor, as far from the battery as possible.

3. Start the disabled tractor following the normal starting instructions previously

provided; then disconnect the jumper cables in the exact reverse order of their

connection.

4. Have the tractor’s electrical system checked and repaired as soon as possible to

eliminate the need for jump starting.

OPERATION

Stopping the Engine

1. Disengage the PTO.

2. Move the RH and LH lapbar drive control levers fully outward into the Park

Brake engaged position.

3. Move the throttle control to the FAST position.

4. Turn the key to the STOP position and remove the key from the ignition module.

Note: Always remove the key from the ignition module to prevent accidental

starting or battery discharge if the equipment is left unattended.

Practice Operation (Initial Use)

Operating a zero-turn tractor is not like operating a conventional type riding tractor.

Although and because a zero turn tractor is more maneuverable, getting used to

operating the lapbar drive control levers takes some practice.

It is strongly recommended that you locate a reasonably large, level and open

“practice area” where there are no obstructions, pedestrians, or animals. You should

practice operating the tractor for a minimum of 30 minutes.

Carefully move (or have moved) the tractor to the practice area. When performing the

practice session, the PTO should not be engaged. While practicing, operate the tractor at

approximately ⁄-⁄ throttle and at less than full speed in both forward and reverse.

Carefully practice maneuvering the tractor using the instructions in the following

section “Driving the Tractor.” Practice until you are confident that you can safely

operate the tractor.

Driving the Tractor

WARNING

Keep all movement of the lapbar drive control levers slow and smooth. Abrupt

movement of the control levers can affect the stability of the tractor and could

cause the tractor to flip over, which may result in serious injury or death to the

operator.

1. Adjust the operator’s seat to

the most comfortable position

that allows you to operate the

controls. See seat adjustment in the

Assembly section.

2. Move the RH and LH lapbar drive

control levers inward in the neutral

position which also disengages the

parking brake. Refer to Figure 24.

Note: Lapbar drive control levers

must be moved fully inward before

pushing forward or backward to

ensure brakes are fully disengaged.

Parking the tractor on uneven terrain

or a hill may cause the brakes to bind

and not release fully. In this case the

tractor will not drive when the lapbar drive control levers are moved. If this

happens, move the lapbar drive control lever in the opposite direction slightly

to take the load off the brakes and allow them to release fully.

Note: If the lap bar drive control levers are not even in the neutral position,

refer to Service & Maintenance for instructions to adjust the lapbar drive

control levers so that they are even.

3. Move the throttle to the full throttle position.

WARNING

Always maintain a firm grip on the control levers. DO NOT release the

control levers to slow or stop the tractor; move levers to neutral position

using your hands.

4. To drive the tractor, firmly grasp the respective lapbar drive control levers

with your right and left hands and continue with Driving the Tractor Forward

in the next section.

Control Levers Moved

Inward & in Neutral

Figure 24

Driving the Tractor Forward

1. Slowly and evenly move

both lapbar drive control

levers forward. The

tractor will start to move

forward. See Figure 25.

2. As the lapbar drive

control levers are pushed

farther forward the

speed of the tractor will

increase.

3. To slow the tractor move

the drive controls lever

rearward to attain the

desired speed, or move

the lapbar drive control

levers to the neutral

position to stop the

tractor.

Turning the Tractor While Driving Forward

WARNING

Sharp turns can affect control of the tractor. ALWAYS slow the tractor

before making sharp turns.

To turn the tractor while driving forward,

move the lapbar drive control levers as

necessary so that one drive control lever

is rearward of the other. The tractor will

turn in the direction of the rearward

drive control lever.

1. To turn to the left, move the left

drive control lever rearward of

the right drive control lever. See

Figure 26.

2. To turn to the right, move the

right drive control lever rearward

of the left lever. See Figure 27.

3. The greater the distance between

the two levers, the sharper the

tractor will turn.

4. To execute a “pivot turn,” move

the turn side drive control lever

to the neutral position, while

moving the other control lever

forward.

Note: Making a “pivot turn” on

grass will greatly increase the

potential for defacement of the

turf.

Driving Forward

Faster

Slower

Neutral

Position

Figure 25

Forward Left Turn

Figure 26

Forward Right Turn

Figure 27

OPERATION

Driving the Tractor In Reverse

WARNING

Always look behind and down on both sides of the tractor before backing

up. Always look behind while traveling in the reverse direction. Mowing in

reverse is not recommended.

1. Slowly and evenly move

both lapbar drive control

levers rearward. The tractor

will start to move in the

reverse direction. See Figure

28.

2. As the lapbar drive control

levers are pushed farther

rearward the speed of the

tractor will increase.

3. To slow the tractor move

the lapbar drive control

levers forward to attain the

desired speed, or move the

lapbar drive control levers to

the neutral position to stop the tractor.

Turning While Driving Rearward

To turn the tractor while driving

rearward, move the lapbar drive

control levers as necessary so that

one drive control lever is forward

of the other. The tractor will turn

in the direction of the forward

lapbar drive control lever.

1. To turn to the left while

traveling in reverse, move

the left drive control lever

forward of the right drive

control lever. See Figure 29.

2. To turn to the right while

traveling in reverse, move

the right drive control lever

forward of the left drive

control lever. See Figure 30.

Note: The greater the

distance between the two

lapbar drive control levers,

the sharper the tractor will

turn.

3. To execute a “pivot turn,”

move the turn side drive

control lever to the neutral

position, while moving the other drive control lever rearward.

Note: Making a “pivot turn” on grass will greatly increase the potential for

defacement of the turf.

Neutral

Position

Slower

Faster

Figure 28

Rearward Left Turn

Figure 29

Rearward Right Turn

Figure 30

Executing a Zero Turn

1. Stop the forward or reverse motion of the tractor by moving the two lapbar

drive control levers to neutral.

2. To turn clockwise, move the

left lapbar drive control lever

forward while simultaneously

moving the right lapbar drive

control lever rearward. See

Figure 31.

3. To turn counterclockwise,

move the lapbar right drive

control lever forward while

simultaneously moving the

left lapbar drive control lever

rearward. See Figure 32.

Stopping the Tractor

1. Move both lapbar drive control levers to the neutral position to stop the

motion of the tractor.

2. Push the PTO downward to the OFF position.

3. Use the deck lift knob/handle to raise the deck to its highest position.

4. If dismounting the tractor, move the lapbar drive control levers fully outward

in the neutral position which also engages the parking brake, move the

throttle to the FAST position, turn the key to STOP

and remove the from

the ignition module.

WARNING

Do not leave the seat of the tractor without disengaging the PTO and moving

lapbar drive control levers fully outward into the Park Brake engaged

position. If leaving the tractor unattended, turn the ignition key to the STOP

position and remove key.

Engaging the PTO

Engaging the PTO transfers power to the cutting deck or other (separately available)

attachments. To engage the PTO:

1. Move the throttle to the FAST

position.

2. Pull the PTO switch up/out into the ENGAGED (ON) position.

Note: When operating the tractor be certain that the throttle is always in the

FAST

position. Operating with the throttle at less than full throttle may

lead to premature battery wear and a poor quality cut.

3. To disengage the PTO, push the PTO switch down/in to the DISENGAGED

(OFF) position.

Clockwise Zero Turn

Figure 31

Counterclockwise Zero Turn

Figure 32

OPERATION

Mowing

WARNING

To help avoid blade contact or a thrown object injury, keep bystanders,

helpers, children and pets at least 75 feet from the machine while it is in

operation. Stop machine if anyone enters the area.

WARNING

Make certain the area to be mowed is free of debris, sticks, stones, wire or

other objects that can be thrown by the rotating blades.

Note: Do not engage the mower deck when lowered in grass. Premature wear and

possible failure of the ‘V” belt and PTO clutch will result. Fully raise the deck or move

to a non grassy area before engaging the mower deck.

• Mow across slopes, not up and down. If mowing a slope, start at bottom and

work upward to ensure turns are made uphill.

• Do not mow at high ground speed, especially if a mulch kit or grass collector

is installed.

• Do not cut the grass too short. Short grass is prone to weed growth and

yellows quickly in dry weather.

• Always operate the tractor with the throttle in the FAST position while

mowing.

• On the first pass pick a point on the opposite side of the area to be mowed.

Follow the point to maintain a straight line.

• Engage the PTO and move the throttle control or throttle/choke control to

the FAST position.

• Lower the mower deck to the desired height setting.

• For best results it is recommended that the first two laps be cut with the

discharge thrown towards the center. After the first two laps, reverse the

direction to throw the discharge to the outside for the balance of cutting.

This will give a better appearance to the lawn.

• Slowly and evenly push the RH and LH lapbar drive control levers forward to

move the tractor forward, and keep the tractor headed directly toward the

alignment point.

Note: The speed of the tractor will affect the quality of the mower cut.

Mowing at full speed will adversely affect the cut quality. Control the ground

speed with the lapbar drive control levers.

• Your tractor is designed to cut normal residential grass of a height no more

than 10” (25cm). Do not attempt to mow through unusually tall, dry grass

(e.g., pasture) or piles of dry leaves. Dry grass or leaves may contact the

engine exhaust and/or build up on the tractor.

• Do NOT attempt to mow heavy brush and weeds or extremely tall grass. Your

tractor is designed to mow lawns, NOT clear brush.

• Keep the blades sharp and replace the blades when worn.

• When approaching the other end of the strip, slow down or stop before

turning. A U-turn is recommended unless a pivot or zero turn is required.

• Align the mower with an edge of the mowed strip and overlap

approximately 3” (7.6 cm).

• Direct the tractor on each subsequent strip to align with a previously cut

strip.

• To prevent rutting or grooving of the turf, if possible, change the direction

that the strips are mowed by approximately 45° for the next and each

subsequent mowing.

When stopping the tractor for any reason while on a grass surface, always:

• Move the RH and LH lapbar drive control levers fully outward into the Park

Brake engaged position.

• Shut engine off and remove the key.

• Doing so will minimize the possibility of having your lawn ‘‘browned’’ by hot

exhaust from your tractor’s running engine.

SERVICE AND MAINTENANCE

MAINTENANCE SCHEDULE

WARNING

Before performing any type of maintenance/service, disengage all controls

and stop the engine. Wait until all moving parts have come to a complete

stop. Disconnect spark plug wire and ground it against the engine to

prevent unintended starting. Always wear safety glasses during operation

or while performing any adjustments or repairs.

Follow the maintenance schedule given below. This chart describes service

guidelines only. Use the Service Log column to keep track of completed

maintenance tasks.

Refer to the Engine Operator’s Manual for engine maintenance items listed in the

table below.

Before

Each use

After First

5 Hours

Every 10

Hours

Every 25

Hours

Every 50

Hours

Every 100

Hours

Every 200

Hours

Prior to

Storing

See Engine

Manual

Check/Clean Engine Intake Screens & Cooling Fans #

Check/Clean Exhaust Manifold, Muer Pipe &

Muer Shields #

Check/Clean Top & Underside of Deck, Under and

Around Spindle Covers & Belt Area #

Check/Clean Around Fuses, Wiring and Wiring

Harnesses #

Check/Clean Around Transmission, Axle and Fans #

Check/Add/Change Transmission Fluid as needed

Check Air Filter for Dirty, Loose or Damaged Parts

Check Engine Oil Level

Clean Battery Terminals

Grease All Lubrication Points

Check Engine Intake Screen/Clean as Needed

Check Blades/Sharpen or Replace as Needed

Check Tire Pressure

Check/Clean Underside of Deck

Check Safety Interlock System

Check ROPS hardware and Seat Belt Assembly

Check Mower Blade Stop Time

Inspect & Lube Deck Wheels

Check Deck Level/Pitch

Check Belts & Pulleys for Damage/Wear

Check That All Hardware is in Place & Secure

Check Engine Mounting Bolt Torque

(Tighten to 325-450 in.-lbs. (37-50 N-m))

3333

Check Blade Mount Nut Torque

(Tighten to 70-90 ft. lbs. (95-122 N-m))

333

Check Spark Plug Condition & Gap

333

Engine Break-In Oil Change

Change Engine Oil

333

Check Fuel System (Lines, Tank, Cap, Fittings)

3333

Check Spark Arrestor

3333

Replace Oil Filter

333

Clean or Change Air Filter

Replace Fuel Filter

Have Valve Lash Checked & Adjusted *

* -- Have this item performed by an authorized service dealer

#-- Perform more often in dry conditions and/or when mulching

SERVICE AND MAINTENANCE

Note: This Operator’s Manual covers several models. Tractor features may vary by

model. Not all features in this manual are applicable to all tractor models and the

tractor depicted may differ from yours.

Post-Operation Tractor Care

After each operation of the tractor, to ensure safe operating conditions refer to

Maintenance Schedule chart in this manual for proper tractor care.

WARNING

Failure to follow these recommendations may result in serious injury to

yourself or others and may cause damage to the tractor.

Cleaning the Tractor

WARNING

If the tractor has been recently run, the engine, muffler and surrounding

metal surfaces will be very hot and can cause burns to the skin. Let the

engine cool for at least five minutes. Exercise caution to avoid burns.

Your tractor should be cleaned after each use and under certain conditions, i.e. dry

conditions and/or mulching situations, additional cleaning may be necessary.

One of the best ways to keep your tractor running efficiently and to reduce fire risk

is to regularly remove debris buildup from the tractor. Follow the recommendations

below and contact your authorized dealer with any questions.

• Allow the machine to cool for at least five minutes in an open area before

cleaning.

Note: Using a pressure washer or

garden hose is not recommended

for cleaning your tractor other

than to clean the underside of

the deck. It may cause damage to

electrical components, spindles,

pulleys, bearings or the engine.

The use of water will result

in shortened life and reduce

serviceability.

• Keep both sides of

transmission cooling slots,

exhaust manifold, around

fuses, all wiring and

harnesses, muffler pipe,

muffler shield, engine

intake screens and cooling

fins, etc. clear of grass

clippings and leaves. See

Figure 33.

• Clean the top of the mower

deck, under the spindle

covers and belt area. See

Figure 34.

Figure 33

Figure 34

• Clean around and near

the transmission, axle

and the fan area. See

Figure 35.

• Debris can accumulate

anywhere on the

tractor, especially on

horizontal surfaces.

Additional cleaning

may be necessary

when mowing in dry

conditions or when

mulching.

• Fuel leaks/spills, oil leaks/spills and excess lubrication can also become

collections sites for debris. Immediate repair and cleaning up oil or fuel spills

can help reduce fire hazards.

• In addition to cleaning the tractor before operating and storing, do not

attempt to mow unusually tall grass (10” (25.4 cm) or higher), dry grass (e.g.,

pasture) or piles of dry leaves. Dry grass or leaves may contact the engine

exhaust and/or build up on the mower deck presenting a potential fire

hazard.

Storing the Tractor

• Allow the machine to cool in an open area for at least five minutes before

storing.

• Do not park the tractor near any flammable materials (wood, cloth or

chemicals) or any open flames or other potential source of ignition (furnace,

water heater or any other type of heater).

• Remove all combustible materials from the tractor before storing. Empty

cargo boxes, grass catchers or containers.

• Always shut off fuel flow when storing or transporting if tractor is equipped

with a fuel shutoff.

• Check the fuel system (lines, tank, cap and fittings) per the maintenance

schedule for cracks or leaks. Repair and clean as necessary.

Maintenance

Removing the Floor Panel

WARNING

Do not operate tractor with floor panel removed.

The floor panel can be removed for maintenance, service and cleaning. To remove

the floor panel:

1. Carefully lift the rear of

the floor panel. See 1 in

Figure 36.

2. Slide the floor panel

rearward to free the

front of the floor panel.

See 2 in Figure 36.

3. Lift it off the tractor. See

3 in Figure 36.

4. To place the floor panel

back on the tractor,

carefully fit the front

tabs at the front of the

floor panel into place

and lower the rear of the

panel down into place.

Wheel Not Shown For Clarity

Figure 35

Figure 36

SERVICE AND MAINTENANCE

Engine

WARNING

Allow machine to cool in an open area for at least five minutes before

storing or refueling.

Refer to the Engine Operator’s Manual for all engine maintenance procedures and

instructions.

Note : Maintenance, repair, or replacement of the emission control devices and

systems which are being done at owner’s expense may be performed by any engine

repair establishment or individual. Warranty repairs must be performed by an

authorized dealer.

Changing the Engine Oil

WARNING

If the tractor has been recently run, the engine, muffler and surrounding

metal surfaces will be very hot and can cause burns to the skin. Let the

engine cool for at least five minutes. Exercise caution to avoid burns.

Note: The oil filter should be changed at every oil change interval.

To complete an oil change, proceed as follows:

1. Locate the oil drain hose (a) on the side of the engine.

2. Place an appropriate oil collection container with at least a 2.5 quart (2.37

liter) capacity below the opening of the oil drain hose, to collect the used oil.

Remove the oil fill cap/dipstick (b) from the oil fill tube.

3. While holding the

free end of the oil

drain hose over the oil

collection container,

unscrew the square

head hose plug (c)

from the end of the oil

drain hose. See Figure

37. Drain the engine

oil into the collection

container.

4. After draining the oil, wipe any residual oil from the oil drain hose. Thread the

square head hose plug into the oil drain hose fitting and tighten the square

head hose plug to 16 ft.-lbs. (22 N-m).

5. Remove the oil filter (d) and drain into the collection container.

6. Replace the oil filter (d), and refill the engine with new oil as instructed in

the Engine Operator’s Manual.

Note: Place an absorbent towel beneath the oil filter to keep oil off the clutch.

Note: Observe proper disposal laws and regulations for gas, oil, etc. to

protect the environment.

Note: Maintenance, repair, or replacement of the emission control devices

and systems which are being done at owner’s expense may be performed

by any engine repair establishment or individual. Warranty repairs must be

performed by an authorized dealer.

Lubrication

WARNING

Before lubricating, repairing, or inspecting, always disengage PTO,

set parking brake, stop engine and remove key to prevent unintended

starting.

• Using a quality lubricating oil, lubricate all lubrication points. Refer to

maintenance schedule chart located in this manual for proper service intervals.

(b)

(a)

(c)

(d)

Figure 37

Spark Arrestor Maintenance (If Equipped)

Spark arrestor assemblies must be inspected and cleaned periodically (see the service

interval chart in this manual). Visually inspect the screen for tears, broken wires or loose

welds. Replace the spark arrestor assembly if any of these conditions exist. If the screen is

in good condition, clean the screen by brushing away loose dirt or carbon particles.

Tires

Keep the tires inflated to the recommended pressures. Improper inflation will shorten

the tire service life. See the tire side wall for proper inflation pressures. Refer to

maintenance schedule chart located in this manual for proper service intervals.

Observe the following guidelines:

• Do not inflate a tire above the maximum pressure shown on the sidewall of the tire.

• Do not reinflate a tire that has been run flat or seriously under inflated. Have

it inspected and serviced by a qualified tire mechanic.

Hydrostatic Transmission

Your zero turn tractor is equipped with two hydrostatic pumps/transaxles. Some

models are equipped with a transmission oil expansion reservoir. Under normal

operating conditions, the oil level in the expansion reservoirs does not need to be

checked and no additional oil is needed.

Checking & Adding Transmission Oil

WARNING

Check the oil level ONLY before starting the tractor when the transmission

oil is fully cooled.

1. Clean the

reservoir cap

and the area

around the

cap to prevent

debris from

contaminating

the transmission

oil. See Figure 38.

2. Turn the

reservoir

cap counter-

clockwise to

remove, then check the oil level in the reservoir. Oil should be visible at the

bottom of the cup, but the oil level must NOT be above the “FULL COLD” line.

See Figure 38. DO NOT FILL THE RESERVOIR.

3. If necessary to add oil because of some type of leakage, use a quality 20W50

motor oil and add only enough oil to bring the level to the “FULL COLD” line.

Reinstall the cap and fully tighten.

Note: Prior to the initial operation of the tractor, the oil level in the reservoir may

be slightly higher than the maximum due to air in the oil lines. Operation of the

tractor will eventually purge the air from the lines and the oil level will settle to the

maximum.

4. Repeat the process for the other transmission.

Changing the Transmission Oil & Filter (If Equipped)

Note: Refer to maintenance schedule chart located in this manual for proper service

intervals.

To change the transmission oil:

1. Remove the cap from the transmission oil expansion reservoir. See Figure 38.

2. Remove the three filter guard screws (a) and the filter guard (b). Clean any

loose debris from around the filter (c). See Figure 39.

3. Place and oil drain pan with an eight quart (7.6 liter) capacity below the

filter.

4. Remove the filter.

Figure 38

La page charge ...

Cub Cadet 47RIAHA7010 Manuel utilisateur

Marque: Cub Cadet

Modèle: 47RIAHA7010

Catégorie: Tondeuses à gazon

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Cub Cadet 47RIAHA7010 User manual
español: Cub Cadet 47RIAHA7010 Manual de usuario

Cub Cadet 47RIAHA7010 Manuel utilisateur

Cub Cadet 47RIAHA7010 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents