Korg AX1G Le manuel du propriétaire

Marque: Korg

Modèle: AX1G

Taper: Le manuel du propriétaire

E F D J 3

To ensure long, trouble-free operation, please read this manual carefully.

Precautions

Location

Using the unit in the following locations can result in a malfunction.

• In direct sunlight

• Locations of extreme temperature or humidity

• Excessively dusty or dirty locations

• Locations of excessive vibration

Power supply

Please connect the designated AC adaptor to an AC outlet of the correct voltage. Do not connect it to an AC outlet of voltage

other than that for which your unit is intended.

Interference with other electrical devices

This product contains a microcomputer. Radios and televisions placed nearby may experience reception interference. Operate

this unit at a suitable distance from radios and televisions.

Handling

To avoid breakage, do not apply excessive force to the switches or controls.

Care

If the exterior becomes dirty, wipe it with a clean, dry cloth. Do not use liquid cleaners such as benzene or thinner, or cleaning

compounds or flammable polishes.

Keep this manual

After reading this manual, please keep it for later reference.

Keeping foreign matter out of your equipment

• Never set any container with liquid in it near this equipment. If liquid gets into the equipment, it could cause a breakdown, fire,

or electrical shock.

• Be careful not to let metal objects get into the equipment. If something does slip into the equipment, unplug the AC adaptor

from the wall outlet. Then contact your nearest Korg dealer or the store where the equipment was purchased.

Précautions à prendre

Emplacement

L’utilisation de l’appareil dans les endroits suivants risquerait d’être la cause d’un mauvais fonctionnement:

• Sous les rayons directs du soleil

• Dans des endroits de températures extrêmes ou d’une humidité excessive.

• Dans des endroits excessivement sales ou poussiéreux.

• Dans des lieux sujets à des vibrations excessives.

Alimentation DC9V

Veuillez raccorder l’adaptateur secteur fourni à une prise de courant fournissant la tension adéquate. Ne jamais le raccorder à

une prise d’un autre voltage que celui prévu pour l’appareil.

Interférences avec d’autres appareils électriques

Cet instrument contient un micro-ordinateur. Les postes de radio et de télévision situés à proximité peuvent par conséquent

souffrir d’interférences à la réception. Veuillez dès lors faire fonctionner cet appareil à une distance raisonnable de postes de

radio et de télévision.

CE mark for European Harmonized Standards

CE mark which is attached to our company’s products of AC mains operated apparatus until December 31, 1996 means it conforms to EMC

Directive (89/336/EEC) and CE mark Directive (93/68/EEC). And, CE mark which is attached after January 1, 1997 means it conforms to EMC

Directive (89/336/EEC), CE mark Directive (93/68/EEC) and Low Voltage Directive (73/23/EEC).

Also, CE mark which is attached to our company’s products of Battery operated apparatus means it conforms to EMC Directive (89/336/EEC)

and CE mark Directive (93/68/EEC).

THE FCC REGULATION WARNING

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Unauthorized changes or modification to this system can void the user’s authority to operate this equipment.

Um einen langfristigen, einwandfreien Betrieb zu gewährleisten, lesen Sie bitte diese Bedienungsanleitung

sorgfältig durch.

Vorsichtsmaßnahmen

Aufstellung

Betreiben Sie das Gerät nicht in folgenden Umgebungen, da dies zu Fehlfunktionen führen könnte:

• in direktem Sonnenlicht

• bei extremer Temperatur oder Luftfeuchtigkeit

• in extrem staubigen oder schmutzigen Umgebungen

• unter dem Einfluß starker Vibrationen

Stromversorgung

Schließen Sie den mitgelieferten Wechselstromadapter bitte nur an eine Steckdose mit korrekter Netzspannung an. Schließen

Sie den Adapter nicht an eine Netzsteckdose an, die eine Spannung liefert, für die Ihr Gerät nicht vorgesehen ist.

Interferenzen bei anderen Elektrogeräten

Dieses Produkt ist mit einem Mikrocomputer ausgerüstet. Bei der Aufstellung in direkter Nähe von Rundfunk-und Fernsehgeräten

kann deren Empfang durch Interferenzen gestört werden. Betreiben Sie dieses Gerät deshalb in ausreichender Entfernung von

Rundfunk- und Fernsehempfängern.

Handhabung

Bedienen Sie die Schalter und Regler nicht mit übermäßiger Kraft, um Beschädigungen zu vermeiden.

Reinigung

Wenn das Gehäuse verschmutzt ist, reinigen Sie es mit einem trockenen, weichen Tuch. Verwenden Sie keine flüssigen

Reinigungsmittel, zum Beispiel Leichtbenzin, Verdünner, Lösungsmittel oder brennbare Polituren.

Bedienungsanleitung

Nachdem Sie die Bedienungsanleitung gelesen haben, sollten Sie sie für den späteren Gebrauch gut aufbewahren.

Fremdgegenstände

• Stellen Sie keine Behälter mit Flüssigkeit in die Nähe dieses Geräts. Wenn Flüssigkeiten in das Gerät gelangen, könnte dies einen System-

ausfall, Brand oder Stromschlag zur Folge haben.

• Achten Sie darauf, daß keine Metallgegenstände in das Gerät gelangen. Sollte dies dennoch geschehen, ziehen Sie den Wechselstrom-

adapter aus der Netzsteckdose. Setzen Sie sich anschließend mit dem nächstgelegenen Korg-Fachhändler oder dem Geschäft in Verbin-

dung, in dem Sie das Gerät gekauft haben.

Manipulations

Pour éviter tout dommage, ne jamais exercer une force excessive sur les interrupteurs ou les commandes.

Entretien

Essuyer l’extérieur avec un chiffon propre et sec. Ne jamais utiliser de détergents liquides comme du benzène ou du thinner ni

des composants de nettoyage ou des cires inflammables.

Conserver le manuel

Après avoir lu attentivement le présent manuel, veuillez le conserver pour pouvoir le consulter ultérieurement.

Tenir tout corps étranger à l’écart de l’instrument:

• Ne jamais poser de récipient contenant du liquide à proximité de l’instrument. La pénétration de liquide dans l’instrument

risquerait de provoquer une panne, un incendie ou un court-circuit.

• Veiller à ce qu’aucun objet métallique ne tombe dans l’instrument. Si un corps étranger a pénétré dans l’équipement,

débrancher l’adaptateur de la prise secteur puis contacter le représentant Korg le plus proche ou le magasin où l’équipe-

ment a été acheté.

* CE-Marke der EG-Norm

Die CE-Marke auf unseren netzgespeisten Geräten deutet auf deren Übereinstimmung mit den EMC- und CE-Richtilinien

der EG (respektive 89/336/EWG und 93/68/EWG) hin. Diese Abzeichen ist bis zum 3. Dezember 1996 gültig.

Die CE-Marke ab 1. Januar 1997 deutet auf Übereinstimmung mit den EMC-, CE- und Niederspannungsstrom-Richtilinien

der EG (respektive 89/336/EWG, 93/68/EWG und 93/68/EWG) hin.

Die CE-Marke auf unseren batteriegespeisten Geräten deutet auf deren Übereinstimmung mit den EMC- und CE-Richtilinien

der EG (respektive 89/336/EWG und 93/68/EWG) hin.

* Marque CE de conformité aux normes de sécurité européennes

La marque CE attachée à nos produits alimentés par secteur indique que ces produits sont conformes à la directive EMC (89/336/

CEE) ainsi qu'à la directive relative à la marque CE (93/68/CEE).Cette marque est valable jusqu'au 31 décembre 1996.

La marque CE attachée après le 1 janvier 1997 indique que ces produits sont conformes à la directive EMC (89/336/CEE), à la

directive relative à la marque CE (93/68/CEE) ainsi qu'à la directive relative au courant de guitare tension (73/23/CEE).

Enfin, la marque CE attachée à nos produits alimentés par batterie indique que ces produits sont conformes à la directive EMC (89/

336/CEE) ainsi qu'à la directive relative à la marque CE (93/68/EEC).

Table of contents Table des matière

NOTICE D’

EMPLOI

BEDIENUNGSANLEITUNG

OWNER’S MANUAL

Appendices Appendices

Anhänge

Table of contents

■ Introduction ............................................ 7

1. Main features .............................................. 7

2. Installing the batteries .................................. 7

3. Front and rear panel.................................... 7

●Front panel ..........................................................7

●Rear Panel ..........................................................8

●LCD display .........................................................8

4. Making connections ..................................... 9

■ Play mode ............................................ 10

1. Let's play the AX1G ................................... 10

●Turn on the power .............................................10

●Adjusting the master level (overall volume) ......... 10

●Select a program and play ................................. 10

2. Bypass and mute ....................................... 10

●Bypass ..............................................................10

●Mute .................................................................10

3. Tuner......................................................... 11

●Tuning your guitar .............................................11

●Changing the calibration ....................................11

4. Metronome................................................ 11

●Start the metronome, and adjust the tempo and out-

put level (volume) ..............................................11

5. Using the expression pedal ........................ 12

●Play using the expression pedal .........................12

●Using the Sample & Play effect ...........................12

●Calibrating (adjusting) the expression pedal .......13

■ Edit mode............................................. 14

1. Selecting the parameter to edit ................... 14

2. Editing effect parameters ........................... 14

●DRIVE ................................................................14

●TONE ................................................................14

●MOD .................................................................14

●PEDAL ...............................................................15

●AMB .................................................................15

●CR ....................................................................15

●NR ....................................................................15

3. Editing other parameters............................ 15

●LEVEL ................................................................15

●RENAME ...........................................................15

●WRITE ...............................................................16

4. Restoring the preset programs (factory setting

programs) ................................................. 16

■ Appendices .......................................... 50

1. Effect Parameter list ................................... 50

2. Preset program parameter list .................... 55

3. Troubleshooting ......................................... 55

4. Specifications ............................................ 58

■ Introduction ............................................... 17

1. Caractéristiques principales......................... 17

2. Mise en place des piles ................................. 17

3. Panneaux avant et arrière ............................. 17

●Panneau avant ......................................................... 17

●Panneau arrière ....................................................... 18

● Affichage LCD ........................................................ 18

4. Raccordements ................................................. 19

■ Mode de jeu ............................................... 20

1. Comme nt jouer sur le AX1G ....................... 20

● Mettre l’appareil sous tension ............................. 20

●Réglage du niveau principal (niveau global) .... 20

●Sélectionner un programme et jouer .................. 20

2. Contournement et suppression du son ...... 20

● Contournemen ........................................................ 20

● Assourdissement (Mute) ...................................... 21

3. Accordeur......................................................... 21

● Accordage de la guitare ......................................... 21

● Modification du calibrage .................................... 21

4. Métronome ...................................................... 21

● Démarrer le métronome et régler le tempo ainsi

que le niveau de sortie (le volume) ..................... 21

5. Utilisation de la pédale d’expression ......... 22

● Interprétation en utilisant la pédale d’expression

●Utilisation de l’effet Echantillonnage et Jeu

(Sample & Play) ...................................................... 22

●Calibrage (réglage) de la pédale d’expression .. 24

■ Mode d’édition (EDIT) ............................ 25

1. Sélection d’un paramètre à éditer ............... 25

2. Edition des paramètres d’effets ................... 25

●DRIVE ....................................................................... 25

●TONE ........................................................................ 25

●MOD ......................................................................... 26

●PEDAL ...................................................................... 26

●AMB .......................................................................... 26

●CR .............................................................................. 26

●NR .............................................................................. 26

3. Edition d’autres paramètres ......................... 27

●LEVEL ....................................................................... 27

●RENAME .................................................................. 27

●WRITE ....................................................................... 27

4. Rappel des programmes prédéfinis (program-

mes préenregistrés à l’usine) ....................... 28

■ Appendices .......................................... 50

1. Liste des paramètres des effets ................... 50

2. Liste de paramètre des programmers prédéfinis

................................................................. 55

3. Guide de dépannage ................................. 55

4. Spécifications techniques............................ 58

Inhalt

■ Einleitung ............................................. 29

1. Hauptfunktionsmerkmale ........................... 29

2. Batterien einbauen ..................................... 29

3. Vorder-und Rückseite ................................. 29

●Vorderseite ........................................................29

●Rückseite ...........................................................30

lLC-Display ...........................................................30

4. Anschlüsse herstellen.................................. 31

■ Play-Modus .......................................... 32

1. AX1G spielen ............................................ 32

●Gerät einschalten ..............................................32

●Master Level (Gesamtlautstärke) einstellen ..........32

●Programm wählen und spielen ...........................32

2. Bypass und Mute ....................................... 32

●Bypass ..............................................................32

●Mute .................................................................33

3. Tuner......................................................... 33

●Gitarre stimmen ................................................ 33

●Kalibrierung ändern ..........................................33

4. Metronome................................................ 33

●Starten Sie das Metronom, und stellen Sie das Tempo

und den Ausgangspegel (Lautstärke) ein .............33

5. Einsatz des Expressionpedals ..................... 34

●Spielen und Expressionpedal einsetzen ...............34

●Sample & Play-Effekt einsetzen ..........................34

●Expressionpedal kalibrieren (einstellen) ..............36

■ Edit-Modus ........................................... 37

1. Den zu editierenden Parameter wählen ...... 37

2. Effektparameter editieren........................... 37

●DRIVE ................................................................37

●TONE ................................................................37

●MOD .................................................................37

●PEDAL ...............................................................38

●AMB .................................................................38

●CR ....................................................................38

●NR ....................................................................38

3. Weitere Parameter editieren....................... 38

●LEVEL ................................................................38

●RENAME ...........................................................39

●WRITE ...............................................................39

4. Preset-Programme (Werksprogramme) wieder-

herstellen .................................................. 39

■ Anhänge .............................................. 50

1. Effektparameterliste ................................... 50

2. Parameterliste der Preset-Programme ......... 55

3. Fehlersuche ............................................... 55

4. Technische Daten ....................................... 58

■

●

■

●

■

●

■

Introduction

■ Introduction

Thank you for purchasing the ToneWorks AX1G High

Performance Processor. In order to enjoy long and

trouble-free use, please read this owner’s manual and

use the product correctly. Keep this manual in a safe

place for future reference.

1. Main features

●69 types of effect variation are provided, and

a maximum of seven effects can be used si-

multaneously.

● 30 (10 x three banks) user programs are pro-

vided in internal memory.

● The expression pedal lets you control effects

in realtime.

● The sample & play function lets you record a phrase

that you play (up to 1.8 seconds long), and use the

pedal to play it back.

● The IPE (Integrated Parameter Edit) system

makes editing easy, so you don’t have to deal

with large numbers of confusing parameters.

● A metronome is built-in for convenience when

practicing alone.

● The auto chromatic tuner helps you tune when

the unit is bypassed or muted.

● The friendly user interface features a liquid

crystal display.

●LCD backlit by luminous material -easy view-

ing in dark locations without wearing down the

batteries.

2. Installing the batteries

1 Lightly press on arrow A of the battery case,

and slide the lid upward in the direction of

the arrow to open the case.

2 Insert four AA alkaline batteries (sold sepa-

rately) as shown in the diagram. Be careful

to observe the correct polarity (+ and -) of

the batteries.

3 Close the lid of the battery case.

If you will not be using the unit for an extended

period of time, remove the batteries to prevent

them from leaking.

When the battery empty indicator ( symbol)

appears in the LCD, it is time to replace the

batteries. Replace the batteries as soon as

possible.

Batteries and an AC adapter are not included

with this product. They must be purchased

separately.

3. Front and rear panel

●Front panel

1 DOWN/UP switches

Use these switches to select programs, or to by-

pass or mute the unit.

2 Expression pedal

This controls the effect that you selected as the

pedal effect.

3 TYPE [√]/[®] keys

In Edit mode, these keys are used to select the

type of effect that you wish to edit.

4 VALUE [-]/[+] keys

Use these keys to edit parameters and to turn the

metronome on/off.

5 EDIT/EXIT key

Use this key to enter Edit mode and to return to

Play mode.

6 BANK SELECT key

Use this key to select banks.

7 Pedal indicator

This indicates the on/off status of the pedal effect,

or the recording condition when the sampler effect

is used.

8 BANK/TUNER LED

These LEDs indicate the bank of the selected pro-

gram. When the tuner is operating, these LEDs

function as a tuning meter.

9 PROGRAM/NOTE display

This indicates the program number. When the unit

is bypassed or muted and the tuner is operating, it

indicates the note name.

0 LCD with luminous backlight

Before using the unit in a dark location, expose the

LCD to sunlight or fluorescent light.

Introduction

A PAGE [√]/[®] keys

In Edit mode or when the metronome is on, these

keys are used to select the parameter that you wish

to modify.

B ENTER key

In Edit mode, this key is used to switch the effect

on/off, or to write a program.

●Rear Panel

1 INPUT jack

If you are using batteries, this jack acts as a power

switch. When a cable is connected, the power will

be turned on.

Before turning the power on or off, be sure to

turn down the volume of any equipment that is

connected.

2 Input level switch

Set this switch according to the output of your in-

strument.

H:Suitable for a pickup with a high output level,

such as a humbucking pickup

L: Suitable for a pickup with a low output level,

such as a single coil pickup

3 OUTPUT/PHONES jack

4 DC9V

The separately sold AC adapter (DC9V

)

can be connected here. When this is connected,

the power will be turned on automatically.

5 Cable hook

If the separately sold AC adapter is connected,

hook the cable of the AC adapter around this hook

as shown below. When removing the cable from

the hook, do not apply excessive tension to the

cable.

●LCD display

1 Effect on/off indicators

These indicate the effects (drive, tone, modulation,

pedal, ambiance) which are turned on.

2 Edit mode indicator

3 Battery empty indicator

4 Cabinet resonator on/off indicator

5 Metronome on/off indicator

6 This indicates effect parameter values or the mas-

ter level.

7 This indicates the program name or effect type, etc.

Introduction

4. Making connections

Before you make connections, be sure to turn off the power of your other equipment, or turn the volume down to

zero. Connecting cables are sold separately.

INPUT

OUTPUT/PHONES

DC9V

Hard disk recorder etc.

Audio system

Guitar amp / powered monitor (*1)

Mono 1/4" jack - mono 1/4" jack

Headphones (*1)

AC adapter (*2) to AC outlet

Mono 1/4" jack - mono 1/4" jack

Mono output - mono 1/4" jack/stereo

output - two mono 1/4" jacks

Stereo 1/4" jack - stereo RCA

(phone) jack

Guitar

*1: The OUTPUT/PHONES jack is a stereo output. If you use a mono phone cable to connect the AX1G to a

guitar amp, only the L (left) sound will be output.

*2: If you use batteries, the AC adapter is not necessary. If you use an AC adapter, be sure to use only the

specified model (DC9V

Play mode

■ Play mode

1. Let's play the AX1G

●Turn on the power

The AX1G does not have a power switch. The power

will be turned on when one of the following occurs.

• If you are using batteries, the power will be

turned on when you connect a mono phone

plug cable to the INPUT jack.

If you connect a stereo phone plug cable, the

power will not be turned on.

When the power is turned on, the AX1G will au-

tomatically be in Play mode.

The program selected at power-on will be the

program which had been selected when the

power was last turned off.

To maximize the battery life, disconnect the cable

from the INPUT jack when you are not using the

AX1G.

• If you are using the separately sold AC

adapter, the power will be turned on when you

connect the AC adapter to an AC outlet.

Before you turn off the power of the AX1G, turn

off the power of the other connected equipment.

●Adjusting the master level (overall volume)

The master level adjusts the final output volume of the

AX1G. The master level setting is displayed in Play

mode in the lower right of the LCD.

• Use the VALUE [+] or [-] keys to adjust the

master level. If you continue holding a key,

the value will change rapidly.

Normally you will leave the master level at 30

(maximum). The output of the AX1G will be opti-

mal when the master level is set at 30. If the out-

put sound is distorted when the master level is

30 and you play with the AX1G bypassed, re-

duce the master level so that the sound does

not distort.

●Select a program and play

Here's how to select a user program.

1 Press the BANK SELECT key to switch the

bank between green, orange, and red.

The bank will change each time you press

the key, and the BANK/TUNER LEDs will

change from “

green orange red

”.

2 Press the UP or DOWN switch to select a pro-

gram number.

The program number is shown in the PROGRAM/

NOTE display, and the program name is shown in

the LCD.

red0~9

green0~9

orange0~9

DOWN

2. Bypass and mute

When the AX1G is bypassed, no effects will be ap-

plied, and the tuner will function. When the AX1G is

muted, no sound will be output from the AX1G, and

the tuner will function.

●Bypass

1 Simultaneously press the UP and DOWN

switches and immediately release them to

select Bypass.

The LCD effect on/off indicators will blink, and

after displaying “BYPASS” for approximately one

second, the tuner calibration will appear.

2 Press the UP or DOWN switch to defeat By-

pass.

●Mute

1 Simultaneously press the UP and DOWN

switches and continue holding them down to

mute the output.

While you press the switches, the LCD will indi-

cate “MUTE”. When you release the switches,

the tuner calibration will appear. The effect on/

off indicators will blink in the same way as for

Bypass.

press and hold

2 Press the UP or DOWN switch to defeat Mute.

Play mode

Calibration is not displayed in Edit mode.

4. Metronome

The AX1G provides a metronome that is especially

convenient when you are practicing alone.

●Start the metronome, and adjust the tempo

and output level (volume)

1 Simultaneously press the VALUE [+] and [-]

keys to start the metronome.

The LCD will indicate the metronome tempo.

Even when the metronome is on, you can still

change programs or bypass the AX1G.

It is not possible to turn on the metronome in

Edit mode. Return to Play mode and turn it on.

2 Press the VALUE [+] or [-] key to adjust the

tempo of the metronome.

The metronome tempo can be adjusted in the

range of  = 40–208.

3 Press the PAGE [®] key once to display the

metronome output level.

Pressing the PAGE [√] key will take you back to

the tempo display.

4 Press the VALUE [+] or [-] key to adjust the

metronome output level.

The output level of the metronome can be ad-

justed from 0 to 30.

5 Once again, press the VALUE [+] and [-] keys

simultaneously. The metronome will stop.

The metronome tempo and output level setting

will be remembered even if the power is turned

off.

3. Tuner

When the AX1G is bypassed or muted, the tuner will

automatically operate. If you mute the AX1G, you will

be able to tune without outputting any sound from

your amp system etc., which is convenient during an

on-stage performance.

●Tuning your guitar

1 Bypass (or mute) the AX1G.

The AX1G will enter bypass or mute mode, and

the tuner will operate.

If the metronome is on, the tuner will not oper-

ate.

2 Play the string that you wish to tune.

The note name will appear in the PROGRAM/

NOTE display. If the note you input is higher (#)

than the note name, the decimal point “.” of the

PROGRAM/NOTE display will light.

When the note name is A.

When the note name is A#.

When tuning, be careful to play only one string

at a time.

3 Adjust the tuning head of your guitar to the

desired pitch desired, so that the PROGRAM/

NOTE display shows the correct note name.

4 Make fine adjustments to the tuning of your

guitar so that only the center LED (green) of

the BANK/TUNER LEDs is lit.

pitch is too low pitch is too high

5 When you are finished tuning, turn off By-

pass (or Mute).

●Changing the calibration

The tuner calibration (the frequency of the standard

pitch A) can be adjusted in the range of 438 to 445 Hz.

You can adjust the calibration when the tuner is oper-

ating.

Press the VALUE [+] or [-] keys to change the

calibration.

Changes you make to the calibration will be lost

when the power is turned off. The next time the

power is turned on, the calibration will automati-

cally be reset to 440 Hz.

Play mode

5. Using the expression pedal

You can use the expression pedal to control volume,

wah, chorus effect, and delay time etc. in realtime.

Using the expression pedal, you can control 18 dif-

ferent MOD (modulation) type effects and 13 differ-

ent AMB (ambiance) type effects. The volume can

also be controlled. You can select one of these for

use (refer to p.50 “Effect parameter list”).

●Play using the expression pedal

1 In Play mode, select a program that allows

you to use the expression pedal.

The “

” indicator at the top of the LCD will

light to indicate programs which allow you to use

the expression pedal.

For this example, let's select G (green)-3

“SATCH”.

2 Make sure that the pedal indicator is lit.

If it is not lit, press down on the expression pedal

once to make the pedal indicator light.

If the pedal indica-

tor is dark, press

down on the pedal

Operate the pedal

Pedal indicator

When controlling the volume, it is not possible

to turn the expression pedal on/off. it will re-

main on (the pedal indicator lit).

The pedal indicator (i.e., the on/off state of the

expression pedal) is not remembered when you

write the program in Edit mode.

3 Operate the expression pedal while you play

your guitar.

When you raise and lower the pedal, the output

sound will change accordingly.

Do not apply excessive force to the expression

pedal. Before you operate the expression pedal,

check whether the pedal indicator is lit, and the

amount of force actually required for the effect.

●Using the Sample & Play effect

1. SAMPL1/2, SCRAT1/2

The SAMPL1/2 effect types let you use the pedal to

playback a recorded phrase.

The SCRAT1/2 effect types let you use the pedal to

playback a scratch sound based on a recorded

phrase.

1 Select a program which uses the Sample &

Play effect.

For this example, let's select SAMPL2 R (red)-5

“FWD/BK ”.

2 Press down on the expression pedal to se-

lect record-ready mode.

The pedal indicator will light.

press down

blinking

3 Play a phrase on your guitar.

When you start playing your guitar, recording will

begin automatically, and the pedal indicator will

light.

When recording ends, the pedal indicator will go

dark.

Recording will not begin until your guitar ex-

ceeds a minimum volume level.

4 Operate the expression pedal.

operate the pedal

SAMPL1: The recorded phrase will playback

when you press the pedal.

SAMPL2: The recorded phrase will playback

when you press the pedal, and will

playback in reverse when you return

the pedal.

SCRAT1: A scratch sound will playback when

you move the pedal. Pedal movement

alone will cause the scratch sound to

playback.

SCRAT2: A scratch sound will playback when you

move the pedal while playing your gui-

tar. Pedal movement alone will not pro-

duce playback.

The recorded sound will be cleared (erased)

when the program is changed, when the AX1G

is bypassed or muted, when the effect type is

changed or when the power is turned off.

Play mode

2. LOOP1/2

The LOOP1/2 effect types let you record a phrase

while you playback a loop. This allows you to layer

your own playing onto the playback.

1 Select a program which uses a Sample & Play

effect.

For this example, let's select LOOP 1O (orange)-

7 “S/LOOP”.

2 Press down on the expression pedal deeply

to select record-ready mode.

The pedal indicator will light.

press down

blinking

3 Play a phrase on your guitar.

When you start playing your guitar, recording will

begin automatically, and the pedal indicator will

light.

When recording ends, the pedal indicator will go

dark, and the recorded sound will begin playing

back as a loop.

Recording will not begin until your guitar ex-

ceeds a minimum volume level.

4 Operate the expression pedal.

operate the pedal

LOOP1: The pedal will control the playback vol-

ume.

LOOP2: The pedal will control the length of the

loop. The loop will become shorter as you

return the pedal, and at the minimum

length the loop will not playback at all.

The recorded sound will be cleared (erased)

when the program is changed, when the AX1G

is bypassed or muted, when the effect type is

changed or when the power is turned off.

For SAMPL1/2, the recording time is 0.9 seconds for

hi-fi sound or 1.8 seconds for lo-fi sound. For LOOP1/

2, the recording time is 0.26–1.8 seconds (in approxi-

mately 0.05 second steps). (☞ p.50, “Effect param-

eters”)

The effect type and recording time can be modified in

Edit mode. For details refer to p.15, “PEDAL (Expres-

sion Pedal)”.

●Calibrating (adjusting) the expression pedal

The operating range of the expression pedal can be

adjusted. If you find that the sensitivity of the expres-

sion pedal is not to your liking, you can perform this

adjustment so that the pedal operates ideally. You

should perform the adjustment described below if fully

advancing the pedal does not produce the maximum

effect, or conversely, if it is not possible to turn off the

effect fully.

When calibrating the pedal, use your hand to

operate the pedal. Accurate adjustment may

not be possible if you use your foot to operate

the pedal.

1 While simultaneously holding down the PAGE

[√] key and VALUE [-] key, turn on the power.

The LCD will indicate “PEDAL” for approximately

one second, and then indicate “MIN”.

2 Slowly move the pedal back. When it stops,

take your hand off the pedal and press the

VALUE [+] key.

The LCD will change from “MIN” to “MAX”.

If you press the VALUE [-] key during the cali-

bration operation, calibration will be halted. The

power-on display will appear, and you will be in

Play mode.

press slowly

3 Slowly move the pedal forward. When it stops,

take your hand off the pedal and press the

VALUE [+] key.

The LCD will display “COMPLT” for approximately

one second. Then the initial power-on screen will

appear, and you will be in Play mode.

press slowly

After the calibration has been set, check the op-

eration of the pedal at the MIN and MAX posi-

tions.

Check the operation by selecting an effect type

that has a clearly audible result, such as the ef-

fect type VOLUME, and verify that the MIN level

is produced for a value of 0.

If the calibration operation fails, the LCD will

indicate “ERROR”, and you will return to the

display before calibration (“MIN”). If repeated

attempts are unsuccessful, it is possible that

the AX1G has malfunctioned. Contact a Korg

service center or your dealer.

Edit mode

■ Edit mode

In Edit mode you can make detailed settings for each

effect, and modify the program name.

Press the EDIT/EXIT key and the LCD will indi-

cate “

” showing that the AX1G is in Edit mode.

Press the EDIT/EXIT key once again and you will re-

turn to Play mode. You can edit the on/off setting of

each effect, and its parameters. When you edit a pro-

gram, the “.” (decimal point) of the PROGRAM/NOTE

display will light.

lit in Edit mode

lit when you edit a Program

Edited programs will be lost if you change programs

or turn the power off before writing the edited pro-

gram. While editing, be sure to write your changes

frequently. For the Write procedure, refer to p.16

“WRITE”.

It is not possible to switch modes when the unit

is bypassed (or muted). Defeat bypass (or

mute), and then switch the mode.

If you bypass (or mute) the AX1G in Edit mode,

it is not possible to perform editing operations.

Defeat bypass (or mute) before you continue

editing.

1. Selecting the parameter to edit

• Use the PAGE [√] or [®] key to select the

parameter that you wish to edit.

You can select effects and other parameter in

the order shown by the diagram below.

The currently selected effect display will blink.

Effects which are turned off cannot be edited. To

edit an effect which is turned off, use the PAGE

[√] or [®] key to select the effect, and then press

the ENTER key to turn on the effect.

2. Editing effect parameters

To edit a program, you can select an effect type Drive,

Tone, Modulation, Pedal, or Ambiance, and modify

the value of the parameter assigned to each effect

type.

For the type of effects which can be selected and the

available values of the parameters, refer to the Effect

Parameter table (☞ p.50).

●DRIVE

This provides effects which process the tonal char-

acter, such as compressor, overdrive, and distortion.

❍ENTER key: Turn the effect on/off (the type name

is displayed when on, and “OFF” when

off)

❍TYPE [√]/[®] keys: Select the effect type

❍VALUE [-]/[+] keys: Specify the value of the param-

eter assigned to each effect

type (☞ p.50)

●TONE

This provides effects which adjust the tonal character.

❍ENTER key: Turn the effect on/off (the type name

is displayed when on, and “OFF” when

off)

❍TYPE[√]/[®] keys: Switch between LOW G (low

range gain), MID FC (mid

range frequency), MID G

(mid range gain), and HIGH

G (high range gain)

❍VALUE[-]/[+] keys: Set the frequency or gain (☞p.

50)

Depending on the settings, the output sound

may distort (clip). If this occurs, adjust the level

(☞ p.15 “LEVEL”) so that the sound does not

distort.

●MOD

This provides modulation-type effects such as cho-

rus, flanger, and phaser.

❍ENTER key: Turn the effect on/off (the type name

is displayed when on, and “OFF” when

off)

❍TYPE [√]/[®] keys: Select the effect type

❍VALUE [-]/[+] keys: Specify the value of the param-

eter assigned to each effect

type (☞ p.51–52)

Edit mode

●PEDAL

This provides effects which can be controlled using

the expression pedal. PEDAL provides volume pedal,

PEDAL-mod (modulation-type effects), and PEDAL-

amb (ambiance-type effects).

❍ENTER key: Turn the effect on/off (the type name

is displayed when on, and “OFF” when

off)

❍TYPE [√]/[®] keys: Select the effect type

❍VALUE [-]/[+] keys: Specify the value of the param-

eter assigned to each effect

type (☞ p.52–54)

PEDAL-mod cannot be used simultaneously

with MOD effects. One or the other effect will

be turned off. Also, if the MOD effect is auto-

matically turned off, turning PEDAL off or se-

lecting an effect other than PEDAL-mod will au-

tomatically turn it on once again. Similarly,

PEDAL-amb and AMB effects cannot be used

simultaneously.

●AMB

This provides spatial effects such as reverb and delay.

❍ENTER key: Turn the effect on/off (the type name

is displayed when on, and “OFF” when

off)

❍TYPE [√]/[®] keys: Select the effect type

❍VALUE [-]/[+] keys: Specify the value of the param-

eter assigned to each effect

type(☞ p.54)

●CR

The cabinet resonator (CR) simulates the acoustical

characteristics of the cabinet of a guitar amplifier. It is

particularly effective when you are not using an amp

(e.g., when headphones, mixer, hard disk recorder,

or an audio system is connected).

❍ENTER key: Turn the effect on/off (the type name

is displayed when on, and “OFF” when

off)

❍TYPE [√]/[®] keys: Select the cabinet size

❍VALUE [-]/[+] keys: Specify the depth of the effect

●NR

Adjust the depth of noise reduction. Raising this value

will produce more noise reduction. Normally you will

adjust this so that you do not hear obtrusive noise

when the strings are lightly muted.

❍VALUE [-]/[+] keys: Adjust the depth of noise re-

duction

It is not possible to turn noise reduction off.

If this value is raised excessively, the sound

may be cut off prematurely, depending on the

device that is connected. If this occurs, reduce

the value.

3. Editing other parameters

●LEVEL

Adjust the level for each program.

Depending on the DRIVE or TONE settings, the out-

put sound may be distorted (clipped), so adjust this

parameter so that the sound is not distorted.

❍VALUE [-]/[+] keys: Set the level accordingly

The volume of each program (each tone) will

change depending on the guitar you use. Ad-

just the level as appropriate for your guitar.

●RENAME

Here you can specify a name for each program.

❍TYPE [√]/[®] key: Select the character location

(the selected character will

blink)

❍VALUE [-]/[+] keys: Select the character

Simultaneously pressing [+] and [-] will insert a space

(blank).

The following characters and symbols are available.

Edit mode

●WRITE

A program you edited or created can be written

(stored) into memory.

When the Write operation is selected, the LCD will

indicate “WRITE”, and the program number will blink

in the PROGRAM/NOTE display.

1 Use the BANK SELECT key or the VALUE [+]

[-] keys to select the bank and program num-

ber into which you wish to write the settings.

When you select the writing destination, the pro-

gram name of that writing destination will be dis-

played briefly.

Before you write an edited program onto an-

other program number, make sure that it is OK

to overwrite that program.

2 Press the ENTER key to write the program.

When you write the program, the LCD will indi-

cate “COMPLT” for approximately one second. If

you decide not to write, press the PAGE [√] or

[®] keys to select another display, and the Write

operation will be canceled.

❍ENTER key: Execute the Write operation

❍BANK SELECT key: Select the bank

❍VALUE [-]/[+] keys: Select the program number

4. Restoring the preset programs (factory

setting programs)

1 While simultaneously pressing the PAGE [√]

and VALUE [+] keys, turn on the power.

The LCD will indicate “PLOAD?”.

If you press the VALUE [-] key, you will jump to

the initial power-on display without loading the

preset programs, and the AX1G will enter Play

mode.

2 Press the VALUE [+] key.

The LCD will change to “PLOAD,” and the preset

programs will be loaded. While the data is being

loaded, the bank and program number of the pro-

gram currently being loaded will be shown by

the BANK/TUNER LEDs and in the PROGRAM/

NOTE display.

When loading is complete, the LCD will indicate

“COMPLT” for approximately one second. Then

the initial power-on display will appear, and the

AX1G will enter Play mode.

red 0–9

green 0–9

orange 0–9

Never turn off the power while this operation is

in progress.

Be aware that if you reload the preset programs,

all previously written programs will be overwrit-

ten.

Introduction

■ Introduction

Merci d’avoir fait l’acquisition du Processeur

haute performance Toneworks AX1G. Pour lui

assurer une longue vie sans incidents, veuillez lire

attentivement le présent manuel et toujours veiller

à utiliser l’appareil correctement. Conserver le

manuel dans un endroit sûr afin de pouvoir s’y

reporter ultérieurement.

1. Caractéristiques principales

●69 types de variations d’effets fournies avec

un maximum de sept effets pouvant être utili-

sés simultanément.

● 30 programmes utilisateur, répartis dans 3

banques de 10 programmes, sont prévus dans

la mémoire interne.

● La pédale d’expression permet de contrôler

les effets en temps réel.

● La fonction d’échantillonnage et de jeu per-

met d’enregistrer une phrase jouée (qui peut

durer jusqu’à 1,8 secondes) et d’utiliser la pé-

dale pour la rejouer.

● Le système IPE (édition des paramètres in-

tégrés) facilite l’édition et vous évite de devoir

faire face à un nombre confus de paramètres.

● Un métronome incorporé s’avère extrême-

ment pratique pour les répétitions en solitaire.

● L’accordeur chromatique automatique per-

met d’accorder l’appareil lorsqu’il est con-

tourné ou que le son est coupé.

● L’interface pratique pour l’utilisateur est pour-

vue d’un écran à cristaux liquides.

●Ecran à cristaux liquides rétroéclairé - facilite

la visualisation dans des endroits obscurs sans

épuiser les batteries.

2. Mise en place des piles

1 Appuyer légèrement sur la flèche A du lo-

gement des piles puis glisser le couvercle

vers le haut, dans le sens de la flèche, pour

ouvrir le logement.

2 Insérer quatre piles alcalines de format AA

(vendues séparément) comme indiqué sur le

diagramme. Toujours veiller à bien respec-

ter la polarité (+ et -) des piles.

3 Refermer le couvercle du logement des pi-

les.

Si vous ne comptez pas utiliser l’appareil

pendant une période prolongée, retirer les

piles pour éviter tout dégât dû à des fuites

de produit.

Lorsque le témoin d’épuisement des piles

(symbole

) apparaît sur l’écran LCD, rem-

placer les piles dès que possible.

Les piles et l’adaptateur AC ne sont pas in-

clus avec cet appareil. Veuillez les acheter

séparément.

3. Panneaux avant et arrière

●Panneau avant

1 Commutateurs UP/DOWN (haut/bas)

Ces commutateurs servent à sélectionner des

programmes, à contourner ou à couper le son

de l’appareil.

2 Pédale d’expression

Elle contrôle l’effet sélectionné comme effet de

pédale.

3 Touches TYPE [√]/[®]

En mode d’édition, ces touches servent à sélec-

tionner le type d’effet à éditer.

4 Touches VALUE [-]/[+]

Ces touches servent à éditer les paramètres et à

activer ou à désactiver le métronome.

5 Touche EDIT/EXIT

Sert à accéder au mode d’édition ou à revenir

au mode de jeu.

6 Touche BANK/SELECT (sélection de banque)

Sert à sélectionner les différentes banques.

7 Voyant de la pédale

Celui-ci indique l’état activé ou désactivé de l’ef-

fet de pédale ou la condition d’enregistrement

lorsque l’effet d’échantillonneur est utilisé.

Introduction

8 Voyant BANK/TUNER (banque/accordeur)

Ces voyants indiquent la banque du pro-

gramme sélectionné. Lorsque l’accordeur est

opérationnel, ils servent à évaluer l’accordage.

9 Affichage de PROGRAMME/NOTE

Cet affichage indique le numéro du programme.

Lorsque l’appareil est contourné ou que le son

est coupé alors que l’accordeur est opération-

nel, il indique le nom de la note.

0 Affichage à cristaux liquides rétroéclairé

Avant d’utiliser l’appareil dans un endroit som-

bre, exposer l’affichage à la lumière solaire ou à

une lumière fluorescente.

A Touches PAGE [√]/[®]

En mode d’édition ou lorsque le métronome est

actif, ces touches servent à sélectionner le para-

mètre à modifie.

B Touche ENTER

En mode d’édition, cette touche sert à activer

ou à désactiver les effets ou à mémoriser un pro-

gramme.

●Panneau arrière

1 Borne INPUT (entrée)

Si l’appareil fonctionne sur piles, cette borne sert

d’interrupteur d’alimentation. Le raccordement

d’un câble à celle-ci met l’appareil sous tension.

Avant de mettre l’appareil sous ou hors ten-

sion, toujours diminuer au minimum le vo-

lume de tout équipement qui pourrait y être

raccordé.

2 Commutateur du niveau d’entrée

Régler cet interrupteur en fonction du niveau

de sortie de votre instrument.

H: Convient pour un micro avec un niveau

de sortie élevé, comme un micro anti-

bourdonnements.

L: Convient pour un micro avec un niveau

de sortie faible, comme un micro à une

seule bobine.

3 Borne OUTPUT/PHONES (sortie/casque

d’écoute)

4 DC9V

Sert à raccorder l’adaptateur secteur vendu sé-

parément (DC9V

). Dans ce cas, l’appa-

reil se met automatiquement sous tension.

5 Crochet pour câble

Si vous raccordez l’adaptateur secteur vendu

séparément, accrocher le câble de l’adaptateur

autour de ce crochet comme indiqué ci-dessous.

Lors du retrait du câble du crochet, veiller à ne

pas appliquer une tension excessive au câble.

● Affichage LCD

1 Témoins d’activation/de désactivation des

effets

Ces témoins indiquent les effets (drive, tone,

modulation, pédale, ambiance) qui sont activés.

2 Témoin du mode d’édition

3 Témoin d’épuisement des piles

4 Témoin d’activation/de désactivation du

simulateur d’ampli

5 Témoin d’activation/de désactivation du

métronome

6 Ce voyant indique les valeurs des paramètres

des effets ou le niveau principal.

7 Ce voyant indique le nom du programme ou le

type d’effet, etc.

Introduction

4. Raccordements

Avant d’effectuer les raccordements, toujours vérifier si les autres équipements sont hors tension ou si

leur volume est réduit à zéro. Les câbles de raccordement sont vendus séparément.

INPUT

OUTPUT/PHONES

DC9V

Enregistreur de disque dur, etc.

Système audio

Ampli pour guitare/moniteur sous tension (*1)

Borne mono d'1/4" - borne mono d'1/4"

Casque d'écoute (*1)

Adaptateur secteur (*2) vers prise de courant

Borne mono d'1/4" - borne mono d'1/4"

Sortie mono - borne mono d'1/4" /Sortie

stéréo - deux bornes mono d'1/4".

Borne stéréo d'1/4" - borne st-

éréo RCA (téléphonique).

Guitare

*1: La borne OUTPUT/PHONES est une borne de sortie stéréo. Si vous utilisez un câble té lé phonique

mono pour raccorder l’AX1G à un ampli pour guitare, seul le son L (gauche) sera émis.

*2: Si l’appareil doit fonctionner sur piles, l’adaptateur secteur n’est pas nécessaire. Néanmoins, en cas

d’utilisation d’un adaptateur, toujours employer uniquement le modèle spécifié (DC9V

Mode de jeu

■ Mode de jeu

1. Comme nt jouer sur le AX1G

●Mettre l’appareil sous tension

Le AX1G n’est pas muni d’un interrupteur d’ali-

mentation. Il se met automatiquement sous tension

dans chacune des circonstances suivantes:

• Lors du fonctionnement sur piles, l’appareil

se met sous tension dès que la fiche d’un câ-

ble téléphonique mono est introduite dans

la borne INPUT.

Si vous raccordez la fiche d’un câble télé-

phonique stéréo, l’appareil ne se mettra pas

sous tension.

A la mise sous tension, le AX1G se met auto-

matiquement en mode de jeu.

L’écran affiche le nom du programme. Le pro-

gramme sélectionné à la mise sous tension

sera le programme sélectionné en dernier

avant la mise hors tension.

Pour préserver la durée de vie des piles, dé-

brancher le câble de la borne d’entrée INPUT

dès que vous cessez d’utiliser le AX1G.

• Si vous utilisez l’adaptateur secteur vendu

séparément, l’appareil se met automatique-

ment sous tension dès que vous raccordez

l’adaptateur secteur à une prise de courant.

Mettre les autres équipements hors tension

avant de mettre le AX1G hors tension.

●Réglage du niveau principal (niveau

global)

Le niveau principal permet de régler le volume de

sortie final du AX1G. Le réglage de volume princi-

pal s’affiche en mode jeu dans la partie inférieure

droite de l’écran.

• Utiliser les touches VALUE [+] ou [-] pour

régler le volume principal. Maintenir la tou-

che enfoncée pour changer de valeur plus

rapidement.

Normalement, il convient de laisser le niveau

principal sur 30 (maximum).

Le niveau de sortie du AX1G est en effet le

plus performant lorsque le volume principal

est réglé sur 30. Si le son de sortie est déformé

lorsque le niveau principal est mis sur 30 et

que vous jouez en contournant le AX1G, ré-

duire le niveau principal de sorte à suppri-

mer cette distorsion.

●Sélectionner un programme et jouer

Voici comment sélectionner un programme utili-

sateu.

1 Appuyer sur la touche de sélection de ban-

que BANK SELECT pour commuter entre les

banques verte, orange et rouge.

La banque change à chaque pression de la

touche et les voyants BANK/TUNER passent

de "

vert orange rouge

" et ainsi de suite.

2 Appuyer sur les commutateurs UP ou DOWN

pour sélectionner un numéro de programme.

Le numéro de programme apparaît sur l’affi-

chage PROGRAMME/NOTE et le nom du

programme s’inscrit à l’écran.

rouge 0 à 9

vert 0 à 9

orange 0 à 9

DOWN

2. Contournement et suppression du

son

Lorsque le AX1G est contourné, aucun effet n’est

appliqué et l’accordeur est opérationnel. Lorsque

le son du AX1G est coupé, il n’émet aucun son et

l’accordeur est opérationnel.

●Contournemen

1 Appuyer simultanément sur les commuta-

teurs UP et DOWN et les relâcher immédia-

tement pour sélectionner le contournement

BYPASS.

Les voyants d’activation/de désactivation des

effets clignotent et après l’affichage de

“BYPASS” pendant environ une seconde, le

calibrage de l’accordeur apparaît.

2 Appuyer sur le commutateur UP ou DOWN

pour annuler le contournement.

La page est en cours de chargement...

Korg AX1G Le manuel du propriétaire

Marque: Korg

Modèle: AX1G

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

Korg AX1G Le manuel du propriétaire

Korg AX1G Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents