Sunbeam 4817-8 Manuel utilisateur

Instruction Manual

SUNBEAM

®

OSKAR

®

FOOD PROCESSOR

Manuel d’Instructions

ROBOT DE CUISINE SUNBEAM

®

OSKAR

®

Manual de Instrucciones

PROCESADOR DE ALIMENTOS SUNBEAM

®

OSKAR

®

Manual de Instruções

PROCESSADOR DE ALIMENTOS SUNBEAM

®

OSKAR

®

■

MODEL/MODELO

MODÈLE/MODELO

4817-8

MODEL/MODELO

MODÈLE/MODELO

4817-8

®

2

When using electrical appliances, basic safety instructions should always be followed

including the following:

1.READ ALL INSTRUCTIONS BEFORE USING THE FOOD PROCESSOR.

2.To protect against risk of electrical shock, do not put food processor in water

or other liquid. This may cause personal injury or damage to the product.

3.Close supervision is necessary when any appliance is used by, or near, children

or incapacitated persons.

4.Unplug from outlet when not in use, before putting on or taking off parts and

before cleaning.

5.Do not contact moving parts. Keep hands, hair, clothing and other utensils away from

chopping blade during operation to reduce the risk of injury to persons and/or

damage to the Food Processor.

6.Do not operate Food Processor with a damaged cord or plug or after the appliance

malfunctions, or is dropped or damaged in any manner. Return appliance to the

nearest authorized Sunbeam Appliance Company service facility for examination,

repair or electrical or mechanical adjustment.

7.The use of attachments not recommended or sold by Sunbeam Appliance Company

may cause ﬁre, electrical shock or injury.

8.Do not let cord touch hot surfaces or hang over table edges or counters.

9.Do not use outdoors or for commercial purposes.

10. Blade and Processing Disk are sharp. Handle carefully.

11. To reduce the risk of injury to persons, never place Cutting Blade on Base

without ﬁrst putting Container properly in place.

12. Be certain Container Cover is securely locked in place while operating appliance.

13. Never feed food by hand. Always use Food Pusher.

14. Do not attempt to defeat the cover interlock mechanism.

This Unit for Household Use Only

NOTE: The maximum current rating is based on the attachment for this product

that draws the greatest current. Other accessories may draw less current.

FOR PRODUCTS PURCHASED IN THE US. AND CANADA ONLY:

This appliance is equipped with a polarized plug (one blade is wider than the other).

As a safety feature, this plug will ﬁt in a polarized outlet only one way. If the plug

does not ﬁt fully in the outlet, reverse the plug. If it still does not ﬁt, contact a

qualiﬁed electrician. Do not attempt to defeat this safety feature.

IMPORTANT SAFEGUARDS

SAVE THESE INSTRUCTIONS

3

Food Pusher

Feed Tube

Processing Container

Motor Base

Cutting/

Processing Blade

Ejector Disc

Reversible Slicing/

Shredding Disc

Cover

Parts of Your Oskar

®

Food Processor

As you unpack your new food processor, take a moment to identify each of the various

parts as shown in these illustrations. BE SURE TO HANDLE THE BLADE AND DISK

CAREFULLY, AS THEY ARE VERY SHARP.

By following the simple, step-by-step instructions in this booklet, you will learn how

things go together, which blade or disc to use for each job and how wonderfully

convenient your new food processor really is to use.

4

Assembling Your Oskar

®

Food Processor

Using Clear Container and Cover:

Before you begin, PLEASE BE SURE THAT THE ELECTRIC CORD IS UNPLUGGED.

Set up the motor base facing you on a dry,

level surface with the tallest side of the

motor housing to the rear.

NOTE: Located on the top, back of the motor

base is an arrow and the words “LOCK-ON”

to the left and “UNLOCK-OFF” to the right.

Turn the clear bowl in the direction indicated

to turn the food processor ON or OFF.

Place the clear Processing Container over the

drive shaft on the motor base and rotate the

container until it drops down evenly on the base.

Now turn the Container until it locks ﬁrmly

into position.

NOTE: Each time you re-assemble your food

processor, be sure to attach the Container ﬁrst

and lock it into position. Then, attach the Cover.

Place the cutting/processing blade over the drive

shaft, rotating it slightly until it drops into place.

If you plan to process with blade, now is the time

to add ingredients. THE BLADE IS EXTREMELY

SHARP. USE CAUTION HANDLING THIS BLADE.

To attach the cover, place the Cover on the

Container so that the large locking tab of the

cover is to the right-hand side near the

horizontal slot at the back of the motor base.

When turned counterclockwise, the tab will

engage the automatic switch and the OSKAR

®

Food Processor will turn ON. By moving the

cover in the opposite direction, it will turn OFF.

NOTE: The stainless steel cutting/processing

blade

can only be used in the OSKAR

®

Food Processor's

clear processing container for in-bowl chopping,

mixing or puréeing functions; NEVER with

continuous ﬂow cover on top of the clear bowl.

5

Assembling Your Oskar

®

Food Processor

Using Continuous Flow Cover:

Set up the motor base facing you on a dry,

level surface with the tallest side of the

motor housing to the rear.

Place the clear Processing Container over the

drive shaft on the motor base. Lock into place

.

Place the ejector disc into the container by

holding the stem and placing the disc over

the drive shaft. Allow it to drop into place.

For slicing, hold the slicer/shredder disc with

the raised, curved slicing edge facing upwards.

Place the disc over the ejector disc and allow it

to drop into position.

For shredding, turn the disc over so that

shredding notches are facing upwards.

Place the disc over the ejector disc and

allow it to drop into position.

To attach the cover, place it onto the container

so that the pin in the cover ﬁts into the hole at

the top of the ejector disc. The large locking tab

on the lid is to the right-hand side, near the

horizontal slot on the motor housing: when

turned counterclockwise, the tab will engage

the automatic switch and the OSKAR

®

Food

Processor will turn ON. Turn the cover in the

opposite direction to turn it OFF.

Note: Keep ﬁngers away from the Continuous

Flow Chute when the OSKAR

®

Food Processor

is operating.

6

For more control over slicing and shredding,

load the Feed Tube with ingredients ﬁrst, before

turning the OSKAR

®

Food Processor ON. Always

use the Food Pusher to yield more evenly sliced

or shredded foods – NEVER YOURFINGERS.

Note: The OSKAR

®

Blade and Cutting Disc are

extremely sharp! Use caution when handling, and

storing them safely in their respective containers.

Rest the Food Pusher in the Tube. Now, holding

the Food Pusher with one hand, and Feed Tube

in the other, rotate the cover to the ON position

while pushing gently down on the food pusher.

Turn the OSKAR

®

Food Processor OFF.

Food Processing Techniques – Using the Blade

Pulsing Techniques:

The OSKAR

®

Food Processor processes food

very quickly; in most cases, in seconds!

Therefore, foods can easily become over

processed if you don’t watch carefully. We

suggest that when using the Steel Blade in the

Clear Processing Container, you process foods

no more than a few seconds at a time, turning the

OSKAR

®

Food Processor ON and OFF frequently

until the desired results are obtained. To use this

“Pulsing Technique”, simply rotate the cover

so that the Locking Tab moves in and out of the

Automatic Switch Slot. Pulsing ensures excellent

results every time.

NOTE: Please be sure that the Steel Blade

has stopped spinning completely before

removing the Cover.

7

Placing Food Into the Container:

For the best, most consistent results, you should try to process pieces of food that are of

about equal size. When you cut, break or tear foods into uniform pieces before you begin

processing, the ﬁnished results will be more uniform, too.

You will get faster, more consistent processing results if you do not overload the container.

When using the cutting/processing blade, ﬁll the container with only 3/4 to 1 cup of

ingredients at a time.

NOTE: When processing a heavy load, check to be sure the OSKAR

®

Food Processor is

sitting ﬁrmly on the counter or table top. DO NOT WALK AWAY FROM THE OSKAR

®

FOOD PROCESSOR WHILE PROCESSING.

Chopping Meats:

Pre-cut meats into pieces about 3/4 inch square.

Place the pieces in the container, replace the

cover and process using the pulse technique

for 5 to 7 seconds. never process more than

1 cup of meat cubes at one time.

Chopping Vegetables:

When processing vegetables such as onions,

peel and quarter; cut large onions into eighths.

Place 3/4 cup of the pieces into the container,

turning the OSKAR

®

Food Processor ON and OFF

1 to 2 times to coarsely chop, 3 to 4 times more

to ﬁnely chop. Scrape sides of container once

or twice during processing, if necessary.

Adding Dry Ingredients:

When various recipes call for dry ingredients

such as ﬂour, add them directly into the

container before processing.

Adding Liquid Ingredients:

Liquid ingredients may be added while the

processor is operating by pouring them through

the pouring hole in the cover.

Note: When processing sauces or semi-liquid

ingredients, stop the OSKAR

®

Food Processor

and scrape down the container sides and cover.

Mincing:

Now you can mince garlic, parsley and spices

in seconds! Simply drop halved garlic cloves

or parsley sprigs into the container and process.

Minced foods that cling to the container are

easily swept out with a spatula.

Removing the Blade:

When you have ﬁnished processing, unplug the

electrical cord from the outlet. Remove the cover.

Remove the cutting/processing Blade with food

clinging to it before removing any food from the

container. THE BLADE IS EXTREMELY SHARP.

USE CAUTION WHEN REMOVING THIS BLADE.

Clean the Blade with a scraper over the bowl.

Note: Always wait for the blade or disc to stop

moving completely before removing the cover.

Removing the Container:

Place the cover on the Container. Use the

OSKAR

®

Food Processor's cover to help remove

the Container. Rotate the cover clockwise

180 degrees until the two tabs on the cover

meet the two Container tabs. Continue to turn

the cover, using ﬁrm pressure, with our thumb

against the tabs until the Container is released.

Empty the remaining food from the Container.

8

9

Packing the Food Tube

One of the most important procedures for successful slicing and shredding with

your new Sunbeam OSKAR

®

Food Processor is the way in which you place or pack food

in the Feed Tube.

When slicing or shredding, cut all ingredients ﬁrst to a size that ﬁts comfortably into the

OSKAR

®

Feed Tube. Pack the Feed Tube. While holding food steady and upright with the

Food Pusher, press down consistently until all ingredients are sliced or shredded evenly.

The more ﬁrmly you push, the thicker the slices or shreds.

For best results, the Feed Tube should always be packed somewhat ﬁrmly.

Foods positioned horizontally in the tube will produce long slices or shreds.

For better results, when shredding softer cheeses, such as American, Cheddar,

Mozzarella or Swiss, the cheese should be well chilled before processing.

Harder cheeses such as Parmesan or Romano should be at room temperature

before processing, and grated with the cutting/processing blade.

Preparing the Food:

Long, narrow foods such as carrots or

celery should be cut into even lengths,

about 3 or 4 inches long. Pack the

food into the Feed Tube.

Making shorter slices or shreds:

Pack food items vertically in the

Feed Tube.

Making longer slices or shreds:

Pack food items horizontally in the

Feed Tube.

10

Cleaning, Storing and Caring for Your Oskar

®

Food Processor

When you have ﬁnished processing, unplug the OSKAR

®

Food Processor from the

electrical outlet and remove the cover, slicing/shredding disc or cutting/processing blade

and the container from the motor base.

Wipe the base of your unit a damp cloth, then polish it lightly with a dry one.

NEVER IMMERSE THE MOTOR BASE IN ANY LIQUID.

The processing container, covers, cutting/processing blade, slicing/shredding disc,

ejector disc and food pusher are all dishwasher safe. These parts may be cleaned

on the top rack of a dishwasher.

REMEMBER TO USE EXTREME CAUTION WHEN HANDLING THE

CUTTING/PROCESSING BLADE AND SLICING/SHREDDING DISC.

THEY ARE VERY SHARP!

Cleaning the internal shaft of your cutting/processing blade is most important.

We suggest the use of a small percolator or baby bottle brush to remove any food

particles, then wash and dry the shaft thoroughly.

Sunbeam suggests that you store the OSKAR

®

Food Processor on a dry counter or table

top in your kitchen, where it will always be ready for immediate use. Store the

cutting/processing blade in the clear container. Store the slicing/shredding disc in a safe

location (OUT OF THE REACH OF CHILDREN). The OSKAR

®

blades are EXTREMELY

sharp! Use caution when handling the blades.

After washing and drying the Container, you may wish to apply a small amount of

vegetable oil to the rim of the Cover and Container. This lubrication allows the cover

to move freely when in contact with the Container.

ALWAYS STORE DISC ANDBLADE OUT OF THE REACH OF CHILDREN!

A Few Things To Remember:

1. Use the OSKAR

®

Food Processor only on a dry, level surface – never outdoors,

on a damp surface or on a table edge.

2. Never remove the Cover or the Processor until the Blade or Disc has come

to a complete stop and the unit has been unplugged from an electrical outlet.

3. The motor of your OSKAR

®

Food Processor has been permanently lubricated at the

factory and requires no further attention. Other than recommended cleaning,

no further user maintenance should be necessary. Return your Food Processor

to the nearest Sunbeam authorized independent service center if servicing or repairs

become necessary.

11

Food Processing Suggestions

• Check the food you are processing!

• Over processing is easily done, because the Food Processor works so fast.

Don’t hesitate to stop the unit and check the food you are processing. You can

always process the food a little longer if the food isn’t ﬁne enough. For greater control,

you may with to process the food using a pulsing technique.

• When slicing or shredding, always use the Food Pusher. NEVER use your ﬁngers

or other objects to push the food into the Feed Tube.

• Be careful not to drop spoons, spatulas or other utensils into the Feed Tube.

• If any items should become caught between the blade and the side of the container,

turn OFF the Food Processor and wait until the blade stops turning. Then, unplug

the unit, remove the cover and lift the blade to free the food item.

• Do not overload the machine. The OSKAR

®

Food Processor processes ingredients

so quickly that even large quantities can be prepared in seconds if common sense

is used about the quantity of food put into the container at any time.

• We recommend processing no more then 3/4 to 1 cup of ingredients at a time.

• Never attempt to process hard ingredients that cannot be cut by a normal kitchen knife.

Things like coffee beans and ice will dull the blade and scratch the container;

shredding or slicing something very hard may damage the disc.

• Keep the Food Processor out of the reach of children.

• The Food Processor is not intended to be used as a blender.

• The Container should not be put in the microwave.

• Processing food such as carrots, may temporarily discolor parts of the Food Processor.

To remove discoloration, wash and dry parts thoroughly and allow to air dry overnight.

12

Food Processing Guide

PROCESSING RECOMMENDED GENERAL

TASK BLADE OR DISC PROCESSING INSTRUCTIONS SUGGESTED FOODS

Blend Steel Blade Place all ingredients into Dips, ﬂavored butters,

processing container. (You may salad dressings, sauces

wish to add liquid ingredients and spreads

through the pouring hole.)

Process until smooth.

Chop Steel Blade Foods, such as meat, should be Apples, cabbage, cooked

pre-cut into 3/4-inch cubes. ﬁsh, ham, meat or poultry,

Do not process more than 1 cup corn chips, hard cooked eggs,

of meat cubes at a time. Place all mushrooms, nuts, olives,

ingredients into processing onions, parsley, pickles,

container. Process using the pimento, raw meat, scallions,

PULSE technique until the desired tomatoes, herbs, garlic,

consistency is reached. crackers, cookies

Grate Steel Blade Food should be cut into 3/4-inch Hard cheeses such as

cubes. (Hard cheeses should be Parmesan or Romano

at room temperature.) Place all

ingredients into processing

container. Process using the

PULSE technique until the desired

consistency is reached.

Mix Steel Blade Place all ingredients into Pastry, pizza dough

processing container.

(You may wish to add liquid

ingredients through the pouring

hole.) Process a few seconds.

Use the Pulsing technique

to ﬁnish processing.

DO NOT OVERPROCESS.

13

PROCESSING RECOMMENDED GENERAL

TASK BLADE OR DISC PROCESSING INSTRUCTIONS SUGGESTED FOODS

Purée Steel Blade Place all ingredients into Fresh, cooked or canned fruits

processing container. (such as apples, bananas,

Process until smooth. peaches, pears, strawberries).

Fresh, cooked or canned

vegetables (such as beans,

carrots, corn, peas, potatoes,

or tomatoes), peanut butter

Shred Shredding Disc Pack food into the feed tube. American cheese, carrots,

(Cheese such as American, Mozzarella cheese, onions,

Cheddar, Mozzarella and Swiss, potatoes, Swiss cheese,

should be well chilled before zucchini

processing.)

Note: For shorter shreds, pack

food vertically into feed tube.

For longer shreds pack food

horizontally into feed tube.

Slice Slicing Disc Large food should be cut Fruits (such as apples,

to ﬁt Feed Tube. Pack food into bananas, lemons, limes,

Feed Tube. (Poultry and cheese, melons, oranges, peaches,

such as American, Cheddar or pears, pineapples,

Swiss should be well chilled strawberries); vegetables,

before processing.) such as beets, cabbage,

Note: Use light pressure on Food carrots, celery, cucumber,

Pusher for thinner slices. Use eggplant, lettuce, mushrooms,

ﬁrm pressure for thicker slices. onions, parsnips, potatoes,

For longer slices, pack food tomatoes, zucchini); nuts,

horizontally into Feed Tube. pickles or poultry

For shorter slices, pack food

vertically into Feed Tube.

14

Trouble Shooting Guide

PROBLEM SOLUTION

1. Food is being unevenly processed or the 1. You are overloading the container. Next time,

OSKAR

®

Food Processor moves across process this amount in two or more batches.

the work surface.

2. The Food Processor vibrates unnaturally 2. The blade or disc has not been assembled

or there are signs of the blade or disc properly. Stop the OSKAR

®

Food Processor

hitting against either the processing immediately and reﬁt the cutting tool properly.

Container or Cover while the OSKAR

®

Food Processor is operating.

3. Liquid leaks out of the bowl and down 3. The OSKAR

®

Food Processor liquid capacity

sides of the Processing Container. is not great; therefore, it is not recommended

for mixing beverages and other foods high

in liquid content.

4. After processing, pieces of food are left 4. Small pieces of food left on top of a disc

on top of the slicing/shredding disc. is a normal occurrence.

5. Cover does not move freely when attached 5. Use a small amount of vegetable oil to lubricate

to the container. the edges of the processing container and cover.

6. Food falls over in the food tube 6. Pack the feed tube snugly and apply even

during slicing. pressure to the food being sliced.

2 Year Limited Warranty

Sunbeam Products Inc. warrants to the original purchaser, subject to the limitations and exclusions

set forth below, that this product shall be free, in all material respects, of mechanical and electrical

defects in material and workmanship from the date of purchase for two years. This warranty does

not cover normal wear of parts or damage resulting from any of the following: negligent use or

misuse of the product, use on improper voltage or current, use contrary to operating instructions

or disassembly, repair or alteration by any person other than an authorized service center.

Our obligation hereunder is limited to repair or replacement, at manufacturer's option, of the

product during the warranty period, provided that the product, along with the model number

and original dated proof of purchase, is sent postage prepaid, directly to the following address:

For products purchased in the United States:

SUNBEAM APPLIANCE SERVICE STATION

117 Central Industrial Row

Purvis, MS 39475

For products purchased in Canada:

SUNBEAM APPLIANCE SERVICE STATION (KND)

Please call 1-800-663-8623 or email us

[email protected]

Do not return this product to the place of purchase or to the manufacturer; doing so may delay the

processing of your warranty claim.

Answers to questions regarding this warranty or for your nearest authorized service location may

be obtained by calling toll-free 1-800-597-5978 or by writing to Sunbeam – Consumer Affairs, at

P.O. Box 948389, Maitland, FL 32794-8389. Answers to questions regarding this warranty or for

your nearest Canadian authorized service location may be obtained by calling toll-free in Canada

1-800-667-8623. For warranty information or for an authorized service location outside of the

United States and Canada, please see the warranty service card inserted in the product packaging.

DISCLAIMER

Product repair or replacement as provided under this warranty is your exclusive remedy.

SUNBEAM PRODUCTS, INC. SHALL NOT BE LIABLE FOR ANY INCIDENTAL

OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED

WARRANTY ON THIS PRODUCT OR ANY PART THEREOF. EXCEPT TO THE EXTENT

PROHIBITED BY APPLICABLE LAW, SUNBEAM PRODUCTS, INC. DISCLAIMS ANY

IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE OF THIS PRODUCT OR ANY PART THEREOF. Some states and provinces do not

allow the exclusion or limitation of incidental or consequential damages, or allow limitations on

how long an implied warranty lasts, so the above limitations or exclusions may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights, which vary

from State to State or Province to Province.

16

Il est important d'observer un certain nombre de règles de sécurité élémentaires pendant

l'utilisation de tout appareil électrique:

1. LISEZ TOUTES LES DIRECTIVES AVANT D'UTILISER LE ROBOT CULINAIRE.

2. Pour vous protéger des risques d'électrocution, ne plongez jamais le robot culinaire

dans l'eau ou tout autre liquide.

3. Faites particulièrement attention lorsque l'appareil est utilisé par, ou en présence d'enfants.

4. Débrancher l'appareil lorsqu'il n'est pas utilisé, avant d'y placer ou y retirer des pièces

et avant de le nettoyer.

5. Éviter tout contact avec les parties mobiles.

6. Ne pas faire fonctionner le robot culinaire dont le ﬁl ou la ﬁche est endommagé ou après

que l'appareil ait mal fonctionné, qu'il ait été échappé ou endommagé d'une façon

quelconque. Retourner l'appareil au Centre de Service Autorisé Sunbeam le plus près

aux ﬁns d'inspection, de réparation, de réglage électrique ou mécanique.

7. L'utilisation d'accessoires non conseillés ou vendus par Sunbeam Appliance Company

présente des risques d'incendie, d'électrocution ou de blessure.

8. Ne pas l'utiliser à l'extérieur.

17

Poussoir

Trémie

Contenant de Transformation

Base du Moteur

Lame pour

Transformer/Couper

Disque Rejeter

Disque Réversible

Éminceur/Déchiqueteur

Couvercle

Les Pièces de Votre Robot Culinaire Oskar®

Au cours du déballage de votre nouveau robot culinaire, veuillez prendre un moment pour

bien identiﬁer chacune des pièces montrées ci-dessous. S'ASSURER DE MANIPULER

LA LAME ET LE DISQUE AVEC SOIN PUISQU'ILS SONT TRÈS TRANCHANTES.

En suivant les simples instructions, étape par étape, vous apprendrez comment les articles

vont ensemble, quelle lame ou quel disque utiliser pour chaque tâche et comment votre

nouveau robot culinaire est merveilleusement pratique à utiliser.

18

Assemblage de Votre Robot Culinaire Oskar

®

Utilisation du Contenant et du Couvercle Transparents:

Avant de commencer, s'assurer QUE LE CORDON

ÉLECTRIQUE EST DÉBRANCHÉ.

Placer la base du moteur en face de vous, sur une

surface sèche et de niveau, avec le côté le plus haut

du logement du moteur vers l'arrière.

REMARQUE: Sur la partie supérieure arrière de la base

du moteur, une ﬂèche avec les mots LOCK-ON

(VERROUILLÉ) à gauche et UNLOCK-OFF

(DÉVERROUILLÉ) à droite. Tourner le bol transparent

dans la direction indiquée pour mettre le robot culinaire

en position de marche (ON) ou d'arrêt (OFF).

Placer le contenant transparent sur l'arbre d'entraînement

de la base du moteur et faire tourner le contenant jusqu'à

ce qu'il descende uniformément sur la base. Tourner

maintenant le contenant jusqu'à ce qu'il se verrouille

fermement en place.

REMARQUE: À chaque ré-assemblage de votre robot

culinaire, s'assurer d'attacher d'abord le contenant et de

le verrouiller en place. Attacher ensuite le couvercle.

Placer la lame pour transformer/couper sur l'arbre

d'entraînement en la tournant légèrement jusqu'à ce

qu'elle descende en place. Si vous avez l'intention de

transformer avec la lame, il est maintenant temps

d'ajouter les ingrédients. LA LAME EST EXTRÊMEMENT

TRANCHANTE. IL FAUT LA MANIPULER AVEC

PRUDENCE.

Pour attacher le couvercle, placer le couvercle sur le

contenant de façon à ce que la grande patte de sûreté du

couvercle soit sur le côté droit près de la fente

horizontale à l'arrière de la base du moteur. Lorsque

tournée dans le sens antihoraire, la patte engagera le

commutateur automatique et mettra le robot culinaire

OSKAR

®

en marche. Déplacer le couvercle dans la

direction opposée pour mettre en position d'arrêt.

REMARQUE: La lame pour transformer/couper, en acier

inoxydable, peut être utilisée uniquement dans le

contenant transparent pour transformer en mélange,

purée ou hachage dans le bol; JAMAIS avec le couvercle

à débit continu sur le dessus du bol transparent.

19

Assemblage de Votre Robot Culinaire Oskar

®

Utilisation du Couvercle à

Débit Continu:

Installer la base du moteur en face de vous sur

une surface sèche et de niveau avec le côté le

plus haut du logement du moteur vers l'arrière.

Placer le contenant transparent sur l'arbre

d'entraînement de la base du moteur.

Verrouiller en place.

Placer le disque éjecteur dans le contenant en

tenant la tige et en mettant le disque sur l'arbre

d'entraînement. Le laisser descendre en place.

Pour émincer, tenir le disque éminceur/

déchiqueteur avec le bord à émincer courbé et

en relief vers le haut. Placer le disque sur le

disque éjecteur et le laisser descendre en place.

Pour déchiqueter, tourner le disque de bord de

façon à ce que les encoches pour déchiqueter

soient vers le haut. Placer le disque sur le

disque éjecteur et le laisser descendre en place.

Pour ﬁxer le couvercle, le placer sur le contenant

de sorte que la goupille dans le couvercle entre

dans le trou au haut du disque éjecteur.

La grande patte de verrouillage de sûreté sur

le couvercle est sur le côté droit près de la fente

horizontale sur le logement du moteur;

tourner dans le sens antihoraire pour faire

engager le commutateur automatique et mettre

le robot culinaire OSKAR

®

en marche (ON).

Tourner le couvercle en direction opposée

pour mettre le robot en position d'arrêt (OFF).

REMARQUE: Se garder les doigts loin du

dispositif de déjection immédiate continue

lorsque le robot culinaire OSKAR

®

est en marche.

20

Pour pouvoir mieux émincer et déchiqueter,

remplir d'abord la trémie avec les ingrédients

avant de mettre le robot culinaire OSKAR

®

en

marche. Toujours se servir du poussoir pour

obtenir des aliments tranchés ou déchiquetés

plus uniformes – NE JAMAIS SE SERVIR DE

VOS DOIGTS.

REMARQUE: La lame et le disque de coupe

sont extrêmement tranchants! Se servir de

prudence lors de leur manipulation et de leur

rangement dans leurs contenants respectifs.

Reposer le poussoir dans la trémie. En tenant le

poussoir avec une main et la trémie avec l'autre

main, faire pivoter le couvercle en position de

marche tout en appuyant doucement sur le

poussoir. Tourner le robot culinaire OSKAR

®

en position d'arrêt.

Techniques de Transformation des Aliments – Utilisant la Lame

Techniques à Pulsation:

Le robot culinaire OSKAR

®

transforme les aliments très rapidement, la plupart du temps,

en quelques secondes! Il peut, par conséquent, se produire une surtransformation des

aliments si l'on ne fait pas attention. Lors de l'utilisation de la lame en acier dans le contenant

transparent de transformation, nous suggérons

de procéder à la transformation des aliments

pas plus que quelques secondes à la fois,

en mettant fréquemment le robot culinaire

OSKAR

®

en position de marche et d'arrêt

jusqu'à ce que l'on obtienne les résultats désirés.

Pour utiliser cette «technique à pulsation»,

faire pivoter tout simplement le couvercle de

sorte que la patte de verrouillage entre et sorte

de la fente du commutateur automatique.

La technique de pulsation assure d'excellents

résultats à chaque fois.

REMARQUE: S'assurer que la lame en acier

a complètement ﬁni de tourner avant d'enlever

le couvercle.

La page charge ...

Sunbeam 4817-8 Manuel utilisateur

Ce manuel convient également à

Sunbeam 4817-8 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents