CF-27 Series
OPERATING INSTRUCTIONS
Personal Computer
®
Appendix
LIMITED USE LICENSE AGREEMENT .......23
Names and Functions of Parts...................... 25
Specifications................................................27
Troubleshooting
List of Error Codes ........................................17
Dealing With Problems.................................. 18
Reinstalling Software .................................... 20
Operation
Starting Up/Shutting Down............................10
Handling and Maintenance ........................... 16
Getting Started
Read Me First ................................................. 5
First-time Operation ........................................ 6
Contents
Getting Started
Troubleshooting
Operation
Appendix
[Additional Manual]
Reference Manual
This manual can be accessed on your computer. Please
refer to page 15 on how to access the Reference Manual.
Contents
• Key Combinations
• LED Indicators
• Panasonic Hand Writing
(Touch Pad)
• Suspend/Hibernation
Functions
• Security Measures
• Computing On the Road
• Battery Power
• Using a Multimedia
Pocket Device
• Using PC Cards
• Adding Memory
• Port Replicator
• Using a Printer
• Using an External Display
• Using USB Devices
• Infrared Data
Communications
• Hard Disk Drive
• Setup Utility
• Technical Information
• List of Error Codes
• DMI Viewer
• Dealing With Problems
95
2
Introduction
Thank you for purchasing the Panasonic computer. Please read the operating instructions thoroughly for proper operation of your
new computer.
Customer's Record
Serial
No.
or
Date
of
Purchase
Model
No.*
Code
No.
Dealer's
Name
Dealer's
Address
NOTE: NOTE provides a useful fact or helpful information.
CAUTION: CAUTION indicates a condition that may result in minor or moderate injury.
WARNING: WARNING indicates a hazard that may result in moderate or serious injury.
[Start] - [Shut Down]: This illustration means to click [Start], then to click [Shut Down].
(For some applications, you may need to double-click.)
Enter : This illustration means to press the [Enter] key.
Fn + F5 : This illustration means to press and hold the [Fn] key, then press the [F5] key.
: Where to go for referred information.
: This illustration means to refer to the Reference Manual, which is available on your com-
puter. Please refer to page 15 on how to access this manual.
Illustrations in this manual
Copyright
This manual is copyrighted by Matsushita Electric Industrial Co., Ltd. with all rights reserved. No part of this manual may be
reproduced in any form without the prior written permission of Matsushita Electric Industrial Co., Ltd.
No patent liability is assumed with respect to the use of the information contained herein.
©Matsushita Electric Industrial Co., Ltd. 1998. All Rights Reserved.
Disclaimer
Computer specifications and manuals are subject to change without notice. Matsushita Electric Industrial Co., Ltd. assumes no
liability for damage incurred directly or indirectly from errors, omissions or discrepancies between the computer and the manuals.
Trademarks
PS/2™ is a trademark of International Business Machines Corporation.
Microsoft, MS-DOS, Windows and IntelliMouse are registered trademarks of Microsoft Corporation of the United States and/or
other countries.
Pentium is a registered trademark of Intel Corporation.
PhoenixCard Manager is a trademark of Phoenix Technologies Ltd.
Imation, the Imation Logo, the circle-pyramid logo, SuperDisk and SuperDisk logo are trademarks of Imation Corp.
Acrobat is a registered trademark of Adobe Systems Incorporated.
Panasonic is a registered trademark of Matsushita Electric Industrial Co., Ltd.
*For the Model No., insert the 11 digit number (for example, CF-27RJ48AAM) located on the bottom of the computer.
3
Federal Communications Commission Radio
Frequency Interference Statement
For U.S.A.
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the Panasonic Service Center or an experienced ra-
dio/TV technician for help.
Warning
To assure continued compliance, use only shielded interface
cables when connecting to a computer or peripheral. Also, any
changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
Responsible Party: Matsushita Electric Corporation of America
One Panasonic Way
Secaucus, NJ 07094
Tel No:1-800-LAPTOP-5 (1-800-527-8675)
Incorrectly using peripheral devices may lead to a decrease
in performance, an increase in temperature and/or damage
your computer. For more information on peripheral devices,
please refer to the Reference Manual.
Avoid Magnetic Fields
Keep the computer away from magnets.
Do Not Disassemble the Computer
Do not attempt to disassemble your computer.
Keep Small Objects Away
Do not insert paper clips or other small objects
into the computer.
Avoid Radio Frequency Interference
Do not place the computer near a television or
radio receiver.
Lithium Battery!
This computer contains a lithium battery to enable the date,
time, and other data to be stored in it.
The battery should only be exchanged by service personnel.
Warning! Risk of explosion from incorrect installation or mis-
application!
Lithium Battery
Avertissement concernant la pile au lithium
(pile de sauvegarde)
Pile au lithium!
Le micro-ordinateur renferme une pile au lithium qui permet de
sauvegarder certaines données comme la date et l'heure
notamment. Elle ne devra être remplacée que par un technicien
qualifié.
Avertissement! Risque d'explosion en cas de non respect de cette
mise en garde!
Avoid Excessive Force on the Display
Do not apply excessive downward force on the
display when it is completely opened, especially
when plugs and/or cables are connected to the
rear of the computer.
Precautions
Peripherals
The CF-27 was developed based on thorough research into the
real-world portable computing environments. Exhaustive pur-
suit of usability and reliability under harsh conditions led to in-
novations such has the magnesium alloy exterior, vibration
damped hard disk drive and floppy disk drive, flexible internal
connections. The CF-27's outstanding engineering has been tested
using the stiff MIL-STD- 810E (for vibration and shock) and IP
(for dust and water) based procedures.
As with any portable computer device precautions should be taken
to avoid any damage. The following usage and handling proce-
dures are recommended.
4
Precautions (Battery Pack)
NOTE
The battery pack may become warm during recharg-
ing or normal use. This is completely normal.
Recharging will not commence outside of the allow-
able temperature range (0 °C to 35 °C (32°F to 95
°F)). Once the allowable range requirement is satis-
fied, charging begins automatically. Note that the re-
charging time varies based on the usage conditions.
If the temperature is low, the operating time is short-
ened. Only use the computer within the allowable
temperature range.
Although the battery has remaining capacity, the bat-
tery indicator may light up red or emit a beep. This
indicates a significant rise in the temperature of the
battery pack. This is typically caused by the fact that
the battery pack has been delivering a high level of
power because the computer has been used with the
display at the brightest setting and with the power-
saving function off.
To protect the battery pack from increases in tempera-
ture, the brightness of the display automatically de-
creases, allowing the temperature of the battery to drop.
In this condition, if the computer is left as is, it will
automatically go off after about three minutes have
elapsed. Within that period, therefore, be sure to con-
nect the AC adapter or shut the computer OFF after
saving any open data (if necessary).
Care should be exercised with regard to the following in
order to avoid the possibility of liquid leakage, overheat-
ing, or bursting.
Avoid Heat
Do not throw the battery pack into a fire or
expose it to excessive heat.
Do Not Disassemble
Do not insert sharp objects into the battery pack,
expose it to bumps or shocks, deform, disas-
semble, or modify it.
Do Not Short
Do not short the positive (+) and negative (-)
contacts.
Do Not Put into a Microwave
Do not put the battery pack into a microwave
oven or a pressurized chamber.
Avoid Extreme Heat, Cold and Direct Sun-
light
Do not charge, use or leave the battery pack for
extended periods where it will be exposed to di-
rect sunlight, in a hot place (in an automobile on
a sunny day, for example), or in a cold place.
Keep Articles Away
Do not place the battery pack together with ar-
ticles such as necklaces or hairpins when carry-
ing or storing.
Do not touch the terminals on the battery pack. The battery
pack may no longer function properly if the contacts are dirty
or damaged.
Do not expose the battery pack to water, or allow it to be-
come wet.
If the battery pack will not be used for a long period of time
(a month or more), charge or discharge (use) the battery pack
until the remaining battery level becomes 30% to 50% and
store it in a cool, dry place.
This computer prevents overcharging of the battery by re-
charging only when the remaining power is less than approx.
95% of capacity after the battery is fully charged.
The battery pack is not charged when the computer is first
purchased. Be sure to charge it before using it for the first
time. When the AC adapter is connected to the computer,
charging begins automatically.
Should the battery leak and the fluid get into your eyes, do
not rub your eyes. Immediately flush your eyes with clear
water and see a doctor for medical treatment as soon as pos-
sible.
Discontinue Use
Should the battery emit an abnormal odor, be-
come hot to the touch, become discolored,
change shape, or become in any way different
from normal, remove it from the computer or
charger and discontinue use.
Do Not Use With Any Other Computer
The battery pack is rechargeable and was in-
tended for the specified computer or charger. Do
not use it with a computer other than the one for
which it was designed.
5
Getting Started
Do not power off your computer or press the floppy disk drive eject button while the
MP indicator ( ) is on.
Doing so may damage the data on the floppy disk and render the disk useless.
Use care when handling floppy disks.
To protect the data on your floppy disks or to prevent a floppy disk from becoming stuck in
your computer, avoid the following:
• Sliding the shutter on the floppy disk manually.
• Exposing the disk to a magnetic field.
• Storing the disk in locations prone to high temperatures, low pitched noise, dampness, or dust.
• Applying more than one label on the disk.
Confirm the contents of a floppy disk before formatting it.
Confirm that no important data is on the disk, because all data on the disk will be erased.
Use the write-protect tab.
This is a must for preserving im-
portant data. This prevents your
data from being erased or overwrit-
ten.
Read Me First
Do not expose your computer to shock.
Please use care when handling your computer, shock may damage your hard disk or make
your software applications and data unusable.
Do not power off your computer while software applications are running or HDD indi-
cator ( ) is on.
Properly shut Windows* down to avoid problems ([Start] - [Shut Down] ).
Save all valuable data to floppy disks.
Backing up data to floppy disks will limit damage should trouble occur to your computer or
should you inadvertently change or erase data.
Use the security function for all important data. ( "Security Measures")
Saving Data on the Hard Disk
* This computer uses Microsoft
®
Windows
®
95 Operating System.
Write Enable Write Disable
Write-protect Tab
Saving Data on Floppy Disks
Users are advised to purchase the latest versions of virus protection software and use
them regularly.
Computer Viruses
We recommend you run the software:
• When booting your computer.
• After receiving data.
We recommend that you check data received on floppy disks or from external sources, such
as data downloaded from the Internet, e-mail, etc. (For compressed files, please uncompress
them before running a check).
6
Getting Started
First-time Operation
Please read the steps below to help you learn what parts are included, and to gain an understand-
ing of some basic computer-related operations.
1
Confirm the inclusion of all parts
Make sure the parts shown in the figure have been supplied. If any of these items are
missing or is not working properly, please contact Panasonic Technical Support.
CAUTION
CF-AA1639
Have 2HD floppy disks prepared to create disks that will allow you to reinstall
the operating system should a problem occur. Be sure that these disks are not
write-protected. (It is not necessary for these disks to be preformatted.)
Windows
®
95 Book
CD-ROM
Registration Card
Windows 95 System Pack .... 1
Operating Instructions .........1
Battery Pack ..........................1
FIRSTAID CD......................... 1
AC Adapter............................ 1 AC Cord .................................1
CF-VZSU04
8
Getting Started
First-time Operation
5
Input the Product Number written on the “Certificate of Authenticity” located in
the Windows
®
95 book that comes with this computer then press [Next].
Press [Finish].
6
4
After reading the agreement, select [I accept the agreement] or [I don't accept the
agreement], then press [Next].
If [I accept the agreement] is selected, the [Certificate of Authenticity] will
appear. If [I don't accept the agreement] is selected, the Windows setup will be
aborted.
NOTE
Setup Windows 95
3 Enter your name and your company’s name, then press [Next].
(It is possible to omit the company name item.)
The License Agreement will be displayed.
Select settings for your region, then press [Next].
Select your keyboard layout, then press [Next].
(for U.S.A.: United States 101)
2
1
Moving the cursor ( ) or clicking buttons can be performed with the touch
pad. ( page 12)
NOTE
6
5
Turn your computer on
Slide the power switch toward the rear of the computer and hold it for approximately
one second until the power indicator ( ) turns on before releasing it.
CAUTION
After confirming that the power indicator has turned on, do not touch the power
switch until Windows setup has started.
Once the computer is powered off, you must wait at least ten seconds before
powering it on again.
The power saving function is factory set, so if there is no input from a key, the touch
pad, or the external mouse for two minutes, the power to the LCD is cut (ECO
mode "Computing on the Road" )*.
The LCD will resume operation when the touch pad is used or a key is pressed.
The computer may enter the ECO mode while Windows is setting up or even when
an application software is being installed. In this case, because it is conceivable
that a selection dialog box will be shown, for resuming from the ECO mode, do not
press Enter which may trigger a selection, but instead, press a key unrelated to
the direct triggering of a selection, like .
NOTE
Ctrl
Power Switch
* Except the devices connected to the USB port such as a USB mouse.
4
Read the LIMITED USE LICENSE AGREEMENT ( page 23)
Before removing the seal covering the power switch, please read the LIMITED USE LI-
CENSE AGREEMENT. Removal of this seal indicates agreement to the terms specified.
After you have agreed to the terms, you may turn your computer on.
9
Getting Started
7
Please store the floppy disks in a safe place. They will enable you to return your
computer to close to the condition at the time of purchase should any problems
occur.
When creating floppy disks, do not run any other application program.
When creating floppy disks and the message [Insufficient files to copy] is dis-
played, click [OK] and then contact Panasonic Technical Support.
While the MP indicator ( ) is on, do not remove the floppy disk, power down
your computer or use the suspend or hibernation function ( "Suspend/
Hibernation Functions").
CAUTION
Prepare 2HD floppy disks and make sure they are not in the write-protected state, then
select [Start] - [Programs] - [Panasonic] - [Create FIRSTAID FD] and follow the on-
screen instructions. Place a label identifying the contents on each disk.
Create floppy disks
Press [Next] to install Internet Explorer. Simply follow the on-screen instruc-
tions.
9
Input the correct date, time and time zone and press [Close].
You can also complete these settings at a later time.
7
Simply follow the on-screen instructions. You can also complete these settings
at a later time.
If you wish to complete the printer settings, press [Next]. If not, press [Cancel].8
NOTE
Name of created backup disk
FIRSTAID FD
(When the display for creating the BACKUP DISK is shown, create the disk by following the
on-screen instructions.)
Eject Button
8
Install the Acrobat
®
Reader 3.0
2
3
1 In [Start] - [Run], input [c:\util\avapp\reader\setup.exe], then press [OK].
After reading the "Software License Agreement", select [Yes] if you agree to the
terms.
Press [Next].
4
Press [Finish].
Read the [Readme] file as necessary. To close the file, click in the top right
corner of the window.
5
Press [Next] and set up the Acrobat
®
Reader 3.0.
This concludes the first-time use operation guidelines.
Press [OK].6
Acrobat
®
Reader is necessary to view the Reference Manual, which explains
detailed operational procedures concerning your computer.
NOTE
Label-side up
Insert the shutter-side
headfirst.
10
Operation
Lift up the latch with another finger.
1
Open the display
Starting Up/Shutting Down
Starting Up
2
Turn your computer on
Pull the carry handle forward.
Slide the power switch toward the rear of the computer and hold it for approximately
one second until the power indicator turns on before releasing it.
3
2
If security indicator ( ) is displayed,
you must first enter your password. ( "Security Measures")
* If you are starting from the suspend mode (
"Suspend/Hiber-
nation Functions"), if after three attempts the correct password is not in-
put, or if no password is entered for about a minute, the computer returns
to the suspend mode.
Over three incorrect attempts,
If the correct password is input,
Will Start
Will Not Start*
(Power off)
Upon entering your
password and press-
ing Enter .
When an application or file that was previously displayed ap-
pears on your screen,
the suspend or hibernation function has been set. (
"Suspend/Hibernation
Functions")
4
1
2
3
Lift open the display.
Power Switch
Latch
CAUTION
The computer will not power on when the display is closed (except when con-
necting an external display).
After confirming that the power indicator has turned on, avoid the following
until Windows has completed loading.
• Touching the power switch.
• Performing any keyboard or touch pad (or external mouse) operations.
• Closing the display.
If the display is closed while Windows is starting up, it is possible that color, etc.,
will not be displayed properly. Run the [MS-DOS Prompt] ([Start] - [Programs]
- [MS-DOS Prompt]), and use full screen display mode by pressing Alt +
Enter .
After returning from the full screen mode Alt + Enter again, the display
will be shown correctly.
Once the computer is powered off, you must wait at least ten seconds before
powering it on again.
When the CPU temperature rises, the computer may not power on to prevent the
CPU from overheating. Should this happen, allow the computer to cool down
then switch the power on again.
If the computer still does not power on, please contact Panasonic Technical
Support.
Slide the latch toward the rear of the computer and hold it with one finger.
4
1
11
Operation
Wheel mode operations (almost identical to
the case of using the Microsoft
®
IntelliMouse
TM
for scroll, zoom, etc., operations) are possible
for Microsoft
®
wheel function-compatible ap-
plications.
Microsoft
®
IntelliMouse
TM
is a mouse-type de-
vice that, in addition to the two conventional
buttons, incorporates a wheel able to rotate
forwards/backwards.
3
Select your application
You are able to start working on your computer.
Using the Touch Pad
Use the touch pad to move the cursor on the display and perform normal computer operations.
For instructions on how to handle the touch pad, refer to page 14.
The touch pad has the following two modes of operation.
Scrolling Area
Microsoft
®
IntelliMouse
TM
Wheel Mode
(Setting at the time of purchase)
Only scroll operation is possible for appli-
cations not compatible with the Microsoft
®
wheel function.
Even for applications compatible with the
Microsoft
®
wheel function, there are cases
where only vertical scrolling or only hori-
zontal scrolling is possible in this mode.
Scrolling side-to-side
Possible when a check mark
is added for [Horizontal].
Scrolling up/down
: Typical mouse operations use this area.
When no check mark is added for [IntelliMouse Wheel mode], [Horizontal] and [Verti-
cal] of [Scroll Configuration], the entire surface can be used for typical mouse opera-
tions.
Scrolling Area
Scrolling up/down
Possible when a check mark
is added for [Vertical].
For the Pan and Auto Scroll functions, the entire
work surface of the touch pad can be used for scroll-
ing.
Changing the mode of the touch pad
1
Select from the taskbar and then select [Motion] or select [Motion] in [Start] - [Set-
tings] - [Control Panel] - [Mouse].
2
To set the Microsoft
®
IntelliMouse
TM
Wheel mode
Add the check mark for [IntelliMouse Wheel mode] of [Scroll Configuration].
To set the original mode
Delete the check mark for [IntelliMouse Wheel mode] of [Scroll Configuration] and
add the check mark for [Horizontal] and/or [Vertical] .
3
Press [OK].
NOTE
When you are not sure whether an application is compatible with the Microsoft
®
wheel
function or not, try using both modes. Furthermore, depending on the application, there are
cases where scrolling may not be possible with either mode.
Original Mode
Left Button
Right Button
Work Surface
The power saving function is factory set, so if there is no input from a key, the
touch pad, or the external mouse for two minutes, the power to the LCD is cut
(ECO mode).
The LCD will resume operation when the touch pad is used or a key is pressed.
[System Devices] in [Start] - [Settings] - [Control Panel] - [System] - [Device
Manager] may contain a device or devices bearing an exclamation mark or ques-
tion mark. This does not indicate a malfunction. Such a mark (exclamation or
question mark) will not be displayed if the operating environment of the device
showing the mark is corrected, by for instance installing the driver of the device.
NOTE
12
Operation
Starting Up/Shutting Down
Operate after pressing the two buttons simultaneously.
1 2
or
Two quick taps, but on
the second tap leaving
your finger down (apply-
ing pressure) and moving
it on the work surface.
While holding down the
button, moving your fin-
ger on the work surface.
* In [Start] - [Settings] - [Control Panel] - [Mouse] - [Tap and Buttons]
or
Basic Operation
Function
Touch Pad Operation
Moving the Cursor
Tapping/Clicking
Double-Tapping/
Double-Clicking
Dragging
Scroll*
Scroll a document
(rotate the wheel)
Auto Scroll*
Automatically scroll a document
(move the mouse after clicking the
wheel)
or
Move the tip of your finger
lightly over the surface.
Wheel
Indicates an operation applicable to the Microsoft
®
IntelliMouse
TM
Wheel mode.
Indicates an operation applicable to the original mode.
Original
When a check mark is added for [use Drag
Lock] *
After the drag operation (above : left side), it is
necessary to determine the destination (i.e., loca-
tion of drop) by one tap. Under the condition no
destination is selected, do not use the suspend or
hibernation function. Nothing is shown on the dis-
play, even after resuming from the suspend or hi-
bernation mode.
In this case, the display will return after a tap or
click is made.
Wheel
Original
tapping
clicking
double-tapping
double-clicking
Wheel
Original
Wheel
Original
Wheel
Original
When releasing the auto scroll function:
One tap on the work surface.
Wheel
Wheel
Original
Wheel
Original
13
Operation
Operate while holding down the two buttons.
Ctrl +
Magnify
Reduce
Pan*
Scroll in various directions of a
document
(move the mouse slightly while
holding down the wheel)
Zoom*
Magnify/reduce the display of a
document.
(rotate the wheel while holding
down Ctrl )
Data Zoom*
Display or hide a document, or
perform operations to return to or
proceed with Internet Explorer.
(rotate the wheel while holding
down Shift )
Function
Touch Pad Operation
Wheel
Wheel
Shift +
Within the parentheses () are operations to follow when using an external Microsoft
®
IntelliMouse
TM
.
* Indicates that the movements will differ depending on the application.
Wheel
CAUTION
When an external mouse or trackball with additional functions (e.g., wheel function) is
connected, a part or all of the additional functions may not function. To use these addi-
tional functions, install the driver or application software of the external device by fol-
lowing the procedure below. However, once the driver or application software is in-
stalled, it is possible that a part of the functions of the touch pad (e.g., auto scroll) will no
longer operate even when the touch pad is enabled again (see the procedure for “When
you want to re-enable the touch pad.”).
1
Select [Mouse] in [Start] - [Settings] - [Control Panel].
2
Select [General] in [Mouse Properties], and then select [Change].
3
Select [Show all devices].
4
Select [(Standard mouse types)] for [Manufacturers:], select [Standard PS/2 Port
Mouse] for [Models:], then select [OK].
5
Select [Close]. At the message asking whether to restart the computer, select [No].
6
Power off your computer ( page 14) and connect the external mouse or trackball
device to the computer.
7
Turn the power on and run the Setup Utility ( "Setup Utility"). In [System
Setup], set [Touch Pad] to [Disable] and close the Setup Utility.
8
Following the operating instructions for the connected external mouse, install the
necessary driver.
After the installation, be sure to [Disable] setting for [Touch Pad] of the Setup Utility.
When you want to re-enable the touch pad;
1
Perform steps
1
to
5
of the procedure shown above.
2
Power off your computer ( page 14) and remove the external mouse or trackball
device.
3
Turn the power on and run the Setup Utility ( "Setup Utility"). In [System
Setup], set [Touch Pad] to [Enable] and close the Setup Utility.
4
Perform steps
1
to
3
of the procedure shown above, select [Matsushita] for [Manufac-
turers:] and [Touch Pad] for [Models:], then select [OK].
5
Select [Close]. At the message asking whether to restart the computer, select [Yes].
14
Operation
Starting Up/Shutting Down
1
NOTE
Shutting Down (power off your computer)
From the keyboard,
You may choose to press down on , then select the menu with or .
2
Restarting your computer (without shutting down)
Select [OK] after selecting [Restart].
Confirm shut down
Select [Shut down].
Your computer will power off automatically.
(In the OFF state, if you are not recharging your battery pack or if the pack is fully charged, your computer
consumes approximately 1.5 W.)
Display the shut down screen
After saving important data and closing each application, select [Shut Down] from the
[Start] menu.
This procedure is shutting down without using the suspend or hibernation function.
(
"Suspend/Hibernation Functions"
)
To quickly resume computer operation after shutting down,
The suspend or hibernation function is available. (
"Suspend/Hi-
bernation Functions"
)
NOTE
Handling the Touch Pad
When using a key combination such as Fn + F5 , do not touch the touch pad. If a key
combination is used while the pad is being touched, the function of the key combination
will not work. In addition, it is possible that control of the cursor will be lost and the cursor
will not show proper movements. In such cases, the computer has to be restarted by using
the keyboard (e.g., ).
Do not place any object on the work surface or press down forcefully with sharp-pointed
objects (i.e. nails), hard objects or objects leave marks (i.e. pencils and ball point pen).
Do not allow things that could dirty the touch pad, such as oil. The cursor may not work
properly in such cases.
When the touch pad becomes dirty:
Wipe to remove dirty areas by using a dry soft cloth such as gauze or a soft cloth first
applied with detergent diluted with water and then thoroughly wrung.
Do not use benzene or thinner, or disinfectant-type alcohol.
The double-tapping speed of the touch pad cannot be changed, even if the setting for [Double-
click Speed] in [Start] - [Settings] - [Control Panel] - [Mouse] - [Tap and Buttons] is changed.
NOTE
15
Operation
Run the Reference Manual
1
Turn your computer on
2
Select [Reference Manual] in [Start] - [Programs] - [Panasonic]
About the Reference Manual
(The display may be changed without notification.)
CAUTION
When you read the Reference Manual, it is necessary to install the Acrobat
®
Reader 3.0.
( page 9)
Zoom-in
CAUTION
The Reference Manual can be accessed on your computer. When a printer is connected, it is
also possible to print.
This manual explains functions for you to make greater use of the computer, such as how to add
peripheral devices, how the Setup Utility works and other useful information.
Hand tool
To move around
the current page.
Display the page
Go forward or back a
page, or to the beginning
or end of a document.
Cancel or correct an operation
Change the display size
Perform a “find” operation
Display of
the manual
Table of Content (Items)
By clicking an item, the corre-
sponding page will be displayed at
100%.
Movable splitter bar
This bar can be dragged, for ex-
ample, to the right to enlarge the
display of the Table of Contents.
Change the display size
You can choose to magnify/de-magnify the
display.
Page indicator
A desired page can be displayed by inputting
the page number after clicking here.
Illustrations may be difficult to view depending on the magnification. If this is the case,
we recommend that the display be magnified.
When the taskbar is hidden at the bottom portion of Acrobat
®
Reader, set the maximum
display window size.
If a printer is connected, we recommend printing pages. The illustrations and display
samples may not print with a high quality.
Exit
17
Troubleshooting
List of Error Codes
0200 Failure Fixed Disk
0210 Stuck key
0211 Keyboard error
*0212 Keyboard Controller Failed
0213 Keyboard locked - Unlock key switch
0220 Monitor type does not match CMOS - Run SETUP
*0230 Shadow RAM Failed at offset :
nnnn
*0231 System RAM Failed at offset :
nnnn
*0232 Extended RAM Failed at offset :
nnnn
0250 System battery is dead - Replace and run SETUP
0251 System CMOS checksum bad - Default configuration used
*0260 System timer error
*0270 Real time clock error
0280 Previous boot incomplete - Default configuration used
0281 Memory Size found by POST differed from CMOS
02B0 Diskette drive A error
02B1 Diskette drive B error
02B2 Incorrect Drive A type - run SETUP
02B3 Incorrect Drive B type - run SETUP
02D0 System cache error - Cache disabled
02F0: CPU ID:
*02F4: EISA CMOS not writable
*02F5: DMA Test Failed
*02F6: Software NMI Failed
*02F7: Fail - Safe Timer NMI Failed
device
address Conflict
Allocation Error for:
device
CD ROM Drive
Entering SETUP ...
Failing Bits :
nnnn
Fixed Disk
n
Invalid System Configuration Data
I/O device IRQ conflict
PS/2 Mouse Boot Summary Screen:
nnnn
kB Extended RAM Passed
nnnn
Cache SRAM Passed
nnnn
kB Shadow RAM Passed
nnnn
kB System RAM Passed
Operating system not found
*Parity Check 1
nnnn
*Parity Check 2
nnnn
Press <F1> to resume, <F2> to Setup, <F3> for previous
Press <F2> to enter Setup
PS/2 Mouse:
System BIOS shadowed
UMB upper limit segment address :
nnnn
Video BIOS shadowed
The following is a list of the messages that BIOS can display. Most of them occur during POST.
Some of them display information about a hardware device, e.g., the amount of memory in-
stalled. Others may indicate a problem with a device, such as the way it has been configured.
If your system displays one of the messages marked below with an asterisk (*), write down the
message and contact Panasonic Technical Support. If your system fails after you make changes
in the Setup menus, reset the computer, enter Setup and install Setup defaults or correct the
error. ( "List of Error Codes")
18
Troubleshooting
Dealing With Problems
When a problem occurs, please refer to this page. The Reference Manual also contains detailed information. If you still cannot
troubleshoot the problem, please contact Panasonic Technical Support.
Starting Up
The power indicator or bat-
tery indicator is not lit
or is displayed
[POST Startup Error(s)] is
displayed
The pre-memory count,
Windows startup, or an op-
eration is extremely slow
The date and time are
incorrect
When the previous item is
not the cause
Check the cable connection for the AC adapter.
Check to see if a fully charged battery is properly installed.
Remove the battery pack and disconnect the AC adapter, then connect them again.
Please input your password. If you have forgotten it, contact Panasonic Technical Support.
page 17
Press F9 in the Setup Utility ( "Setup Utility"). This will restore the Setup
Utility's settings to their default values (except the password settings). Then, the Setup Utility
must be run once again for you to input the appropriate operating environment settings. (The
processing speed depends on the application software used, so this operation may not cause the
processing speed to increase.)
You can set the date and time through [Date/Time] in [Start] - [Settings] - [Control Panel].
If you continue to experience problems, the internal battery maintaining the clock may need to
be replaced. Please contact Panasonic Technical Support.
Press F9 in the Setup Utility (
19
Troubleshooting
Cannot read/write to a
floppy disk
Unable to write to a floppy
disk
How to format a floppy
disk is unclear
Unable to read/write to the
hard disk
When the previous item is
not the cause
Disk Operations
Has the floppy disk been correctly inserted?
Has the floppy disk been correctly formatted?
Has the Setup Utility been used to set [Floppy Operation] to [Enable]? (
"Setup
Utility")
Your floppy disk content may be corrupted.
Is the floppy disk write-protected?
Select [Format] in [My Computer] - [3 1/2 Floppy (A:)] - [File]. After confirming the disk
volume and format type, start formatting.
Your drive or file may not have been properly set.
Check to see if the hard disk is full. If it is full, delete unnecessary files.
Your hard disk content may be corrupted. Contact Panasonic Technical Support.
Try testing another drive or media.
No display after powering
on
The power has not been cut,
but after a certain period of
time, there is no display
The resolution of the display
cannot be changed
An afterimage appears
The motion of the mouse
cursor is not smooth
The cursor does not move in
scrolling area of the touch
pad
The cursor cannot be con-
trolled
At the time of purchase, the display setting is preset for an external display. If you connect an
external display, the screen is displayed on the external display.
When there is no display to an external display,
• Check your cable connection to the external display.
• Confirm your display is powered on.
• Check the settings for your external display.
Try changing the display by pressing Fn + F3 .
When displaying only through an external display, if the computer is shut down by using
the suspend or hibernation function, there will be no display on the LCD unless the external
display is connected when operations are resumed. In this case, connect the external dis-
play.
Has the computer been set to the power-saving mode?
To resume operation of your computer from ECO mode, press any key.
To save power, your computer may have automatically entered the suspend or hibernation
mode. (
"Computing On the Road")
Set [None] for [Wallpaper] in [Start] - [Settings] - [Control Panel] - [Display] - [Background],
and then press [OK]. Then, once again try changing the resolution. After the change, be sure
to restart the computer.
If an image is displayed for a prolonged period of time, an afterimage may appear. This is not
a malfunction. The afterimage will disappear when a different screen is displayed.
Select [Start] - [Settings] - [Control Panel] - [Mouse] - [Motion] and add the check mark
for [Show trails].
When the Microsoft
®
IntelliMouse
TM
Wheel mode or the original mode is set for the touch
pad, only scroll operations are possible for the right part or bottom part of the touch pad. In
this case, cursor operations are possible by using the work surface excluding the right part or
bottom part. When no mode is set, the entire surface of the touch pad can be used for cursor
operations. ( page 11)
Was the touch pad touched while a key combination (such as Fn + F5 ) was being used?
In this case, restart the computer by using the keyboard (e.g., ).
Display
20
Troubleshooting
Reinstalling Software
Microsoft Windows 95 Startup Menu
1. Boot
2. Initialize the HDD for the Hibernation function
3. Restore the HDD to factory default
Enter a choice: 1
Select [2.Initialize the HDD for the Hibernation
function].
At the confirmation message, press .
When the message [Press any key to continue...]
is displayed, confirm that the FIRSTAID FD has
been set in the floppy drive, and then press a key.
The computer will reboot.
Before Reinstallation
Preparing
Reinstalling
CAUTION
1
Insert the FIRSTAID FD, and turn the computer on; this
screen should appear.
If data on your hard disk is compressed, the data should
be uncompressed.
Important
Save all important data. If reinstallation is carried out, all data existing prior to the installation will be lost. The reinstalla-
tion will return the computer to close to the conditions at time of purchase.
Before the reinstallation procedure, remove all peripherals (except for the CD-ROM drive and FDD cable).
Be sure the AC adapter is connected until the reinstallation procedure is completed.
You will need the FIRSTAID CD, CD-ROM included in the Windows 95 System Pack and the FIRSTAID FD you made
earlier.
If you have not created the FIRSTAID FD, you can create by selecting [Create FIRSTAID FD] in [Start] - [Programs]
- [Panasonic]. If you can not create this disk, please contact Panasonic Technical Support.
NOTE
Windows 95 (HDD format)
The CD-ROM pack (CF-VCD271) and FDD cable (CF-VCF271) are required for the following reinstallation procedure.
Mount the CD-ROM pack in the multimedia pocket and connect the FDD cable to the floppy disk drive. (Refer to the
operating instructions of the CD-ROM pack and FDD cable for details.)
2
3
1
1
Start Windows and insert the FIRSTAID FD.
2
Select [Start] - [Programs] - [Accessories] - [NotePad] and open [a:\config.sys].
3
Rewrite the following line and save.
REM ***************************************
Device=A:\UP\WINDOWS\COMMAND\ATAPICD.SYS /D:MSCD000
4
Copy the CD-ROM driver file (i.e., the driver file rewritten in step
3
) of the CD-ROM drive below
[a:\up\windows\command] of the FIRSTAID FD.
5
Set the floppy to the write-protect state.
Rewrite this driver for the driver of your CD-ROM drive. Please refer to
the operation manual that accompanies the CD-ROM drive.
If you connect a CD-ROM drive through a PC card, the driver for the PC
Card will be necessary. Refer to the operation manual that accompanies
the CD-ROM drive.
Y
When using a CD-ROM drive other than CF-VCD271 (e.g., by connecting it through a PC Card);
For the CD-ROM drive to be properly recognized
It is necessary to copy the CD-ROM driver to the FIRSTAID FD with the method below. However, after hard
disk is formatted, the operation below is not possible.
Before performing the operation below, we recommend creating a duplicate of the FIRSTAID FD with the DISKCOPY
command.
NOTE
When using a CD-ROM drive not supported by Windows 95
After reinstalling Windows 95 (after step
11
on page 21), there is a need to install the proper driver software. Refer
to the operation manual that accompanies the CD-ROM drive.
There are cases the reinstallation procedure will slightly differ.
2
To use the hibernation function, follow this procedure
and be sure to create the hibernation partition.
If you decide not to create the hibernation partition, go
on to step 4 after restarting the computer by pressing
Alt + Ctrl + Del .
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
Panasonic CF-27 Series Manuel utilisateur
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: Panasonic CF-27 Series User manual
Documents connexes
-
Panasonic CF-47 Series Manuel utilisateur
-
-
-
-
-
-
-
-
-