Breville the Breville Sous Chef 16 Peel & Dice Manuel utilisateur

the Sous Chef

®

16 Peel & Dice

Instruction Book - BFP820

2

BREVILLE

RECOMMENDS

SAFETY FIRST

At Breville we are very safety

conscious. We design and

manufacture consumer

products with the safety of you,

our valued customer, foremost

in mind. In addition we ask

that you exercise a degree of

care when using any electrical

appliance and adhere to the

following precautions.

IMPORTANT

SAFEGUARDS

READ ALL

INSTRUCTIONS BEFORE

USE AND SAVE FOR

FUTURE REFERENCE

• Blades, cutting disc, and

dicing blade are sharp.

Handle them carefully.

• Remove and safely discard

any packaging materials

and promotional labels

before using the appliance

for the ﬁrst time.

• To eliminate a choking

hazard for young children,

remove and safely discard

the protective cover ﬁtted

to the power plug of this

appliance.

• To protect against

electrical shock, do not

immerse the power cord,

power plug or motor base

in water or any other liquid.

• Do not place the

appliance near the edge

of a countertop or table

during operation. Ensure

the surface is level, clean

2 Breville recommends safety ﬁrst

8 Components

11 Assembly

14 Functions

22 Food Processing Guide

24 Care & Cleaning

26 Troubleshooting

28 Basic Recipes

35 French

Contents

3

and free of water. Vibration

during operation may cause

the appliance to move

during use.

• Do not place the appliance

on or near a hot gas or

electric burner, or where

it could touch any other

source of heat.

• Do not use on a sink.

• Always make sure the food

processor is completely

assembled before operating.

The appliance will not

operate unless properly

assembled.

• Ensure the POWER/OFF

button has been pressed

and the power cord is

unplugged from the power

outlet before attaching any

blade, disc or lid.

• Handle the food processor

and attachments with care.

Blades and discs are razor-

sharp and should be kept

out of reach from children.

• Always secure the

processing bowl onto the

motor base before attaching

the blades or discs.

• Do not allow the power

cord to hang over the edge

of a table or counter, touch

hot surfaces or become

knotted. Unwind the power

cord fully before use.

• Keep hands as well as

spatulas and other utensils

away from moving blades

or discs while processing

food, to prevent the

possibility of severe

personal injury or damage

to the food processor.

A plastic spatula may be

used, but only when the

food processor is stopped.

• Ensure the POWER/OFF

button has been pressed

to switch the motor off

and remove the power

cord from the outlet before

removing the lid from the

processing bowl.

• Avoid contact with moving

parts. Never push food

down by hand when slicing

or shredding. Always use

pusher.

• Make sure motor has

completely stopped before

removing cover.

4

• Never store any blade or

disc on motor shaft. To

reduce the risk of injury,

never place cutting blade

or discs on the shaft

without ﬁrst putting bowl

properly in place. Store

blades and discs, as you

would sharp knives, out of

reach of children.

• Be sure cover is securely

locked in place before

operating food processor.

• Never try to override

or tamper with cover

interlock mechanism.

• Always remove the plug

from the power outlet if

the appliance is not in

use, before attempting to

move the appliance, before

cleaning, disassembling,

assembling and when

storing the appliance.

• Some stiff mixtures, such

as dough, may cause the

processing blade to rotate

more slowly than normal.

If this happens, do not

process for longer than

1 minute.

• Do not process hot or

boiling liquids – allow

liquids to cool before

placing into the processing

bowl.

• Do not move appliance

while in operation.

• Do not place any part of

the food processor in a

microwave oven.

• Do not ﬁll the processing

bowl above the 12 cup

liquid level (2.8L) or

16 cup dry level

(shredding). Always add

drier or thicker ingredients

to the processing bowl

prior to adding ﬂuids.

• Never remove the lid while

the appliance is operating.

Always use the POWER/

OFF or PAUSE buttons to

stop the machine before lid

removal.

• Care should be taken

when removing the food

from the processing

bowl by ensuring the

motor and blade/disc has

completely stopped before

disassembling.

5

Ensure the POWER/OFF

button has been pressed

to switch the motor off

and unplug the power

cord from the power outlet

before removing the lid

from the processing bowl.

The processing bowl

should then be unlocked

from the motor body and

the blade/disc should be

carefully removed before

attempting to remove the

processed food.

• Do not use harsh abrasive,

caustic cleaners or oven

cleaners when cleaning the

appliance.

• Strictly follow the care

and cleaning instructions

described in this book.

• To avoid possible

malfunction of work

bowl switch, never store

the food processor with

pusher assembly in locked

position.

• This appliance is for

household use only.

Do not use the appliance

for anything other than

its intended purpose as

described in this book.

Do not use outdoors.

Do not use in moving

vehicles or boats.

• The use of attachments

not sold or recommended

by Breville may cause ﬁre,

electric shock or injury.

• Do not leave the appliance

unattended when in use.

• Ensure the motor and

blade/disc have

completely stopped

before disassembling.

Ensure the POWER/OFF

button has been pressed

to switch the motor off

and unplug the power

cord from the power outlet

when not in use, if left

unattended and before

assembling, cleaning or

storing.

• This appliance is not

intended for use by young

children or inﬁrm persons

without supervision.

6

Young children should be

supervised to ensure that

they do not play with the

appliance.

• Regularly inspect the

power cord, power plug

and actual appliance

for any damage. Do not

operate if damaged in any

way or after the appliance

malfunctions. Immediately

cease use of the appliance

and visit www.Breville.com

or call Breville Consumer

Support for examination,

repair or adjustment.

• For any maintenance other

than cleaning, visit

www.Breville.com or

call Breville Consumer

Support.

• This appliance has a

polarized plug (one blade

is wider than the other). To

reduce the risk of electric

shock, this plug will ﬁt in a

polarized outlet only one

way. If the plug does not ﬁt

fully in the outlet, reverse

the plug. If it still does

not ﬁt, contact a qualiﬁed

electrician.

Do not modify the plug in

any way.

• If the power outlet is

a standard 2-prong

wall outlet, it is your

personal responsibility

and obligation to have it

replaced with a properly

grounded 3-prong wall

outlet.

• Do not, under any

circumstances, cut or

remove the third (ground)

prong from the power cord

or use an adapter.

• Consult a qualiﬁed

electrician if instructions

are not completely

understood, or if doubt

exists as to whether the

appliance is properly

grounded.

SHORT CORD

INSTRUCTIONS

Your Breville appliance

is ﬁtted with a short

power supply cord to

reduce personal injury or

property damage resulting

from pulling, tripping or

7

becoming entangled

with a longer cord.

If an extension cord is used,

(1) the marked electrical

rating of the cord set or

extension cord should

be at least as great as the

electrical rating of the

appliance, (2) the cord

should be arranged so

that it will not drape over

the countertop or table-

top where it can be pulled

on by children or tripped

over unintentionally and

(3) the extension cord

must include a 3-prong

grounding plug.

BREVILLE ASSIST

®

PLUG

Your Breville appliance

comes with a unique

Assist

®

Plug, conveniently

designed with a ﬁnger hole

to ease removal from the

power outlet.

For safety reasons it is

recommended you plug

your Breville appliance

directly into its own

electrical outlet on a

dedicated circuit separate

from other appliances. If the

electric circuit is overloaded

with other appliances,

your appliance may not

function properly. Use in

conjunction with a power

strip or extension cord is

not recommended.

CALIFORNIA

PROPOSITION 65:

(Applicable to California

residents only).

WARNING

This product contains

chemicals known to the

State of California to cause

cancer.

FOR HOUSEHOLD USE ONLY

SAVE THESE INSTRUCTIONS

8

P

Components

A

B

C

D

E

F

G

H

J

K

L

I

O

P

M

N

A. Small food pusher

For improved processing control of smaller

ingredients. It also doubles as a measuring

cup for adding/measuring ingredients. The

food processor will run continually whether

the small pusher is in or out.

B. Medium pusher

The food processor will run continually

whether the medium pusher is in or out.

C. Large food pusher

For pushing food down the feed chute.

The food processor will not start unless the

large pusher is correctly in place.

D. Extra wide 5.5 inch chute

For larger ingredients.

E. Feed chute safety system

Prevents the motor from operating unless

the bowl and lid are correctly locked in

position, and large feed pusher is inserted.

F. Processing lid

Locks onto the processing bowl.

G. Silicone seal

Reduces the chance of leakage while

processing large volumes of liquid

ingredients.

H. Mini bowl

For better control when processing

small quantities.

I. Processing bowl with handle

16 cup bowl for dry ingredients and

10 cups for diced and liquid (thick, wet

ingredients e.g. soups). The processing bowl

locks onto the motor base.

J. LCD display

Displays the timing function.

K. Count up & count down timer

Used to set desired time required for

processing. Can count up or down, stopping

the processor once the time is reached in

count down mode.

L. POWER|OFF button

M. START|PAUSE button

Pauses the Timer.

9

N. PULSE button

Press down and hold brieﬂy for short bursts

of power. The motor will automatically stop

after the PULSE button has been released.

O. Direct drive motor base

1200W induction motor with safety

braking system.

P. Non-skid rubber feet

For added safety and stability.

Q. Dough blade

Blunt blade designed for a softer action of

combining dough ingredients.

R. Mini processing blade

Use this blade for small quantities with

the mini bowl for chopping, mixing and

blending a variety of ingredients.

S. Micro-serrated S-Blade™

Swift action for chopping, mixing, and

blending a variety of ingredients.

T. S-Blade™ safety cover

U. Whisk/emulsifying disc

Use this attachment for whisking of eggs

and cream.

V. Adjustable slicer

Use this disc for slicing ingredients.

Able to slice from 0.3mm –8.0mm thick.

W. French fries cutter

Use this disc for cutting vegetables to make

french fries.

X. Julienne disc

Use this disc for julienning vegetables.

Y. Reversible shredder

Use one side for small/thin shredding and

the other side for coarse shredding.

Z. Disc spindle

Use with the reversible shredder, julienne,

french fry cutting disc, whisk, potato peeler

and adjustable slicing discs in position.

Q

T

S

R

U

V

W

X

Y

Z

10

AA. Peeler disc

Peels potatoes and other round,

ﬁrm produces.

AB. Dicing disc

For dicing 12mm cubes.

AC. Dicing grid

For dicing 12mm cubes.

AD. Dicing Distributor

Only use for Dicing bigger quantities

(more than 5 cups). Distributes diced

food evenly in bowl

AE. Cleaning cap

To clean the 12 mm dicing grid.

Attaches to the large food pusher.

AF. Geared spindle

Use with the dicing kit.

AG. Plastic spatula

For scraping the sides of the bowl

helping to process ingredients evenly.

AH. Cleaning brush

For cleaning the processor bowl, blades,

discs, dicer grid and cleaning cap.

AI. Storage box

For storing all accessories.

AA

AB

AC

AD

AE

AF AG AH

AI

11

Assembly

BEFORE FIRST USE

• Before using your food processor for the

ﬁrst time, remove any packaging material

and promotional labels. Ensure the POWER

button is OFF and the food processor is

unplugged.

• Be careful when handling the blades and

discs as they are extremely sharp.

• Wash the processing bowl, processing lid

and all attachments in warm soapy water

with a soft cloth. Rinse and dry thoroughly.

All attachments except the geared spindle

and large food pusher may be washed in the

dishwasher.

• When ﬁrst using your food processor, you

may notice an odor coming from the motor.

This is normal and will dissipate with use.

• Always use the food processor on a dry,

level work surface.

ASSEMBLY

Motor Base and Bowl

1. Position the processing bowl onto the motor

base with the handle in line with the ALIGN

HANDLE graphic on the motor base.

2. Turn the bowl clockwise until the handle

locks to the front. The processing bowl

should now be securely locked into position.

The food processor will not operate unless

the bowl is locked into position correctly.

12

Spindles and Discs

1. Before placing the lid onto the processing

bowl, choose your spindle and position

it over the coupling in the center of the

processing bowl. Then position your chosen

attachment over the spindle. Please note

that the S- Blade and Dough Blade do not

require a spindle for processing.

2. The disc spindle is required when using

the following discs: adjustable slicer,

reversible shredder, julienne, French fries

cutter and the peeler. IMPORTANT:

Do not use the geared spindle for those

attachments. Failing to use the disc spindle

will damage the parts, and incorrect use this

way may cause the parts to fuse together.

Julienne disc

French fries cutter

Slicing disc

Reversible Shredding disc

Peeler

Disc spindle

3. The geared spindle is required when using

the dicing kit. To dice vegetables or fruit

insert the geared spindle into the bowl ﬁrst,

followed by the dicing grid, ensuring to

align with the 4 tabs in the bowl, then insert

the dicing disc. Make sure you follow the

right order. Do not use your dicing kit with

the disc spindle. Always use the geared

spindle.

Dicing blade

Dicing grid

Geared spindle

Dicing distributor

WARNING

Do not touch the blades

of the Dicing Grid.

They are extremely sharp.

13

Mini Processing Bowl

The mini processing bowl ﬁts inside the

main bowl.

The mini processing blade gives you

maximum control for small quantities.

Do not use any spindle, or the processing discs.

Use only the mini processing blade in the mini

bowl. Please note that the mini blade cannot be

used in the main processing bowl.

Lid

Place lid onto the processing bowl so that

the ALIGN | LOCK graphics on the lid and

handle align. To LOCK the lid, hold the chute

and turn clockwise so that the handle parts

align. Locking the lid correctly will engage the

interlocking safety catch on the handle, and

allow the motor to run.

14

Functions

OPERATION

Getting started

The food processor will only operate when

the processing bowl, lid and large pusher are

correctly assembled. This engages the safety

interlock, and allows the motor to run.

The chute has a CHUTE FILL MAX graphic to

indicate the maximum volume of food that can

be placed in the chute for the pusher to activate

the safety locking catch.

Control buttons

The POWER button illuminates red when the

machine is connected to power and is ready

to run.

The START|PAUSE button allows the motor

to run continuously until pressed again. If the

lid, bowl or large pusher are removed while

the motor is running, the button will ﬂash. The

motor will resume running when the bowl, lid

and large pusher are assembled and the safety

interlock is engaged, the button light will be

solid (no longer ﬂashing).

The momentary PULSE button is ideal for

processing foods that need sudden bursts of

power. It also encourages ingredients to move

around the bowl. PULSE is also best when

processing foods that only require processing

for a short period of time.

Use a combination of the START|PAUSE and

PULSE buttons for control when

processing food.

Timer

If the timer isn’t set, the food processor

timer counts up in seconds. When using

the timer this way, the processor will stop after

10 minutes (9:59), or you can cancel

it manually.

The alternative to running in count-up mode is

to use the arrow buttons to set the timer before

starting.

The count-down timer can be used for any

recipe that speciﬁes the length of time

ingredients should be processed.

To set the count-down timer, press the up or

down arrows until the desired processing time

is displayed on the LCD screen.

When the timer has ﬁnished counting down

the food processor will automatically stop.

After Processing

After processing, wait until the blades/discs

have stopped moving before unlocking the lid.

To ensure safe handling, turn off at the POWER

button and unplug at the power outlet before

handling the blades.

When removing blades/discs, lift the part

by carefully gripping the plastic hub in

the center.

Overload Protection System

The food processor has an overload protection

system to prevent damage to the motor.

If activated, the food processor will go into

STANDBY mode, and the 'OVERLOAD' icon

on the LCD will ﬂash.

Unplug and allow to cool for 30 minutes.

Once cooled, you will be able to use the food

processor as usual again.

Note that some stiff mixtures (such as bread

dough) may cause the blade to rotate more

slowly than normal. If this happens, do not

process for more than 30 seconds.

If the blades or discs jam with food while

processing, immediately stop the machine,

then unplug from the power outlet before

clearing the wedged food. If this happens more

than once, the bowl may be overloaded.

Try processing in smaller batches.

15

DICING WITH THE DICING KIT

The dicing kit dices raw and cooked food into

cubes of the size of 12 x 12mm.

Even cut vegetables can lead to even cooking

and more consistent food results.

IMPORTANT: Always remember to place the

geared spindle, dicing grid and dicing disc into

the food processor before adding the food.

If you intend to dice larger quantities

(more than 5 cups) please insert the Dicing

Distributor after placing your geared spindle

into the bowl. The Dicing Distributor will help

to distribute diced food evenly across the bowl.

Do not dice more than 10 cups (2.4l) in your

food processor at a time. Exceeding this

capacity will lead to the produce jamming in

the disc. It will also make the cleaning process

of the dicing grid challenging.

Clean dicing grid each time after dicing

10 cups.

Place your dicing kit into Food Processor in the

following order:

Dicing

Disc

Lid

Large

Feed Chute

Medium

Feed Chute

Small

Feed Chute

Processing

Bowl

Motor

Base

Dicing

Grid

Geared

Spindle

Dicing

Distributor

16

Vegetables and fruits

The dicing kit can process raw and cooked

vegetables and also fruits. To improve dicing

results for harder vegetables like carrots and

pumpkin, par-cooking is recommended.

Only par-cook vegetables that need to be

cooked afterwards.

For best results when dicing with raw, hard

vegetables feed carrots length-ways through

the small feed chute, and feed pumpkin

through the medium feed chute. Feeding this

produce through the large feed chute may lead

to jamming of the disc.

DO NOT DICE SWEET POTATO

(Yam/Kumara).

Due to its dry, ﬁbrous texture dicing sweet

potato is not recommended with the

Dicing Kit. Sweet Potato places high load on

the Dicing Kit which causes high friction and

potential damage to the Bowl Lid.

When dicing tomato, select ﬁrmer fruit for

optimal results.

Use the START|PAUSE button for control

when dicing food.

To get remaining food out of the grid use the

dicer cleaning cap.

Straight after dicing, remove the dicing disc

from the bowl while leaving the dicing grid

inside the bowl.

Attach the cleaning cap to the bottom of the

large food pusher, align the markings on the

cleaning cap with the markings on the dicing

grid and push down to clear out the food in

the grid.

Repeat four times going around the grid until

the entire grid is cleared.

17

The best size potato

for the peeling disc is

around 2¾" x 2¾".

Choose potatoes that are

round, rather than elongated.

Peeling other produces

The peeler disc can peel potatoes very well but

it can also be used to peel other ﬁrm, round

produces. You get great results with little waste

when peeling beets.

It can also peel carrots and sweet potatoes.

Depending on the size, we recommend cutting

carrots and sweet potatoes in 2-3 pieces before

placing them into the bowl.

CHOPPING WITH THE MICRO-

SERRATED S-BLADE™

The micro-serrated S-blade chops raw and

cooked food to the consistency required,

from coarsely chopped to minced. The blades

process very efﬁciently, and may take less time

than expected to process many large tasks.

Always remember to place the spindle and

S-blade into the processing bowl before adding

the food.

Avoid over-processing by checking the

consistency frequently. For many tasks, we

recommend using the PULSE button, as it may

only take a few seconds to fully process food to

your desired consistency.

If necessary, turn the POWER off and use a

spatula to scrape down the sides of the bowl to

encourage even processing.

Raw vegetables, fruit and cooked meats

Trim and cut food into 1 inch cubes.

Process no more than 7 cups at a time using

the PULSE button at 1–2 second intervals until

chopped to desired size or consistency.

PEELING WITH THE PEELER

Potato peeling made easy

Take the hard work out of peeling potatoes.

The Breville peeler will peel potatoes in

batches of 6–7, depending on the size. Peeling

is very fast, and may ﬁnish quicker than

expected. Keep your eye on progress, and it

should be done in 25–40 seconds.

Size matters

The best size potatoes to use are around

2 ¾" x 2 ¾", which is about the size of this

illustration. Choose potatoes that are round,

rather than elongated.

Use whole potatoes, as cutting potatoes into

half or quarters creates square edges that won't

peel efﬁciently. Using rounder potatoes will

reduce the amount of waste.

Loading the potatoes

Position 6–7 potatoes evenly on top of the

peeler. Potatoes should have enough room

to freely roll and rumble. If potatoes are too

tightly packed, the peeling won't be as effective.

Keep in mind that the peeling works best with

a complete batch, and peeling just a couple

of potatoes won't be as efﬁcient. Lock lid in

place before starting, and never insert potatoes

through the chute.

How long to peel

Peeling is very quick, with most potatoes

taking 25–30 seconds. Less time in the peeler

means less waste, but you may have to remove

the eyes by hand with a paring knife. More

time in the peeler will take a thicker layer off,

including most of the eyes.

TIP

Set the Timer to 25 seconds and review the

results when the product stops. Add extra time

if required for optimum results.

18

Raw meat, chicken and ﬁsh

Trim excess fat and sinew, and cut food into

1 inch cubes. Ensure all bones are removed.

Chill well in freezer until ﬁrm as this will help

to cut through the food more easily. Process

no more than 4 cups (600g) of raw meat at

a time. At this capacity the motor should run

for no more than 30 seconds at a time. Use a

combination of the START and the PULSE

button until chopped or minced to the

desired consistency.

Garlic, chili and ginger

Peel garlic cloves and process them whole.

Leave chili whole, or remove seeds for milder

chilli. Peel and cut ginger into 1 inch cubes.

For other solid herbs like lemongrass or

galangal, peel and cut into cubes or pieces

between ½ and 1 inch in size.

Size should be made smaller for harder or more

dense herbs.

Process using the PULSE button at

1–2 second intervals until chopped to the

desired consistency.

If adding garlic, chilli or ginger to other

ingredients, drop whole pieces down the small

feed chute while the motor is running.

Leafy herbs

Wash and dry herbs thoroughly. Remove

any coarse stems. Process no more than

3 bunches of herbs (approx. 5½ cups) at a time

using the PULSE button at 1–2 second intervals

until chopped to the desired consistency.

Use leafy herbs immediately for the most

aromatic results in your recipe.

Nuts

Process no more than 5 cups of shelled nuts

at a time using the PULSE button at

1–2 second intervals until chopped to the

desired consistency.

Nut butters

Process no more than 5 cups of shelled roasted

nuts at a time using the START button until

chopped to the desired consistency.

The volume of nuts reduces after processing,

for example 2 cups of nuts will make around

1 cup of nut butter.

Natural nut butter (without using stabilisers)

will separate on standing, and needs to be

stirred before use.

For a smoother nut butter, add a little vegetable

oil. This can improve the texture of nuts with a

lower oil content, like roasted almonds.

Soft breadcrumbs

Break stale bread into chunks (fresh bread

will stick to blades). Process no more than

6–8 slices at a time with the processing bowl,

using the PULSE button at 1–2 second intervals

until crumbed to desired consistency.

Dried breadcrumbs

Tear bread into chunks and toast in oven until

golden and crisp. Do not over brown. Process

no more than 6–8 slices at a time with the

processing bowl, using the PULSE button at

1–2 second intervals.

Cookie crumbs

Break cookies into quarters, and weigh

a maximum of 17.6 oz. (2 standard packets).

Process using the PULSE button at

1–2 second intervals until chopped to the

desired consistency. Sweet or savory cookie

crumbs can be used as an alternative to pastry

for sweet or savory pies.

Do not process very hard cookies as this may

damage the blades.

Dried fruit

For dates and other larger dried fruits, remove

pits and cut into quarters before processing.

Process no more than 1 cup at a time.

Dried fruit can be sticky, and may stick

to the blades during processing.

We recommend putting dried fruit in the

freezer for about 10 minutes before processing.

19

Process no more than 2 cups (1 cup for large

fruits) at a time using the PULSE button at

1–2 second intervals until chopped to the

desired consistency.

If chopping fruit to add to cake mixture,

process the fruit before making the cake mix.

Add a little ﬂour (from the quantity of ﬂour in

the recipe) to prevent fruit from sticking to the

S-blade.

PURÉEING WITH THE MICRO-

SERRATED S-BLADE™

The S-blade purees raw and cooked food to the

consistency required, including baby food.

The blades process very efﬁciently, and cut the

time needed to puree many tasks.

Always remember to place the S-blade into the

processing bowl before adding the food.

Carefully remove the S-blade after pureeing

food and use a spatula to scrape food adhering

to the blade and bowl.

Baby food

Trim and cut vegetables and meat into 1inch

cubes. Cook vegetables and meat before

processing. Process no more than

7½ cups at a time using the START | PAUSE

button in intervals until the food is pureed to a

smooth and even consistency.

Stock, milk or gravy can be added through

the small feed chute if the mixture becomes

too thick.

Excess baby food can be frozen in ice-cube

trays, and packed in single serve freezer bags

ready for use.

MIXING WITH THE MICRO-

SERRATED S-BLADE™

The S-blade mixes ingredients for cakes,

batters, and cookie doughs.

The S-blade can also emulsify egg-based

sauces such as mayonnaise.

Always remember to place the spindle and

S-blade into the processing bowl before adding

the food.

Butter cake and cookie dough

Place ﬁrm, chopped butter and sugar into

the processing bowl. Process using the

START | PAUSE button for one minute.

With the motor running, add eggs one at a time

through the small feed chute, mixing well after

each egg is added. Take lid off and add liquid

and dry ingredients to the mixture. Process

using the PULSE button until folded evenly.

Scrape down sides of bowl as needed.

Do not over-process.

Add chocolate chips, nuts, dried fruit, etc after

the main mixture is done. Use the PULSE

button in very short bursts until the additions

are combined. Do not over-process, as these

larger ingredients will break down quickly.

Quick-mix cakes and batters

Place all ingredients in the bowl, starting

with liquids, and being careful not to

exceed the MAX LIQUID level. Process

using the PULSE button until folded evenly.

Scrape down sides of bowl as needed.

Do not over-process.

This method can also be used for melt ’n’ mix

cakes, packet cake mixes and crepe batters.

Pastry dough

Place ﬂour and chilled, cubed butter into the

processing bowl.

Do not process more than 3L cups (500g)

of ﬂour using the START | PAUSE button in

intervals until the butter is absorbed into

the ﬂour.

Steadily add liquid through the small feed

chute with the motor still running.

Process until the mixture forms a ball.

20

KNEADING WITH THE

DOUGH BLADE

Always remember to place the dough blade

into the processing bowl before adding the

food. The edges of the plastic dough blade

create a softer action for combining dough

ingredients.

The dough blade encourages the gluten

strands to be stretched rather than cut, and

should be used for all yeast doughs, and any

other doughs that require kneading.

Bread or pizza dough

Place ﬂour and dry ingredients into the

processing bowl, including instant active

dry yeast.

Do not process more than 3L cups (500g)

of ﬂour or using the START | PAUSE button in

intervals.

Steadily add liquid (including oil, if applicable)

through the small feed chute with the motor

still running. Process until the mixture forms a

soft, elastic dough ball.

Transfer dough ball to a lightly ﬂoured surface

and knead for a further 5 minutes if necessary

until soft and pliable.

If processing more than two batches of dough,

allow the motor base to cool for an extended

period (approx.30 min) before subsequent

kneading to prevent the motor from

overloading.

SLICING, GRATING AND SHREDDING

IMPORTANT

The spindle must be used with both the

adjustable slicer and the reversible shredder/

grater.

Adjustable slicer

The adjustable slicer will slice food to an even

and consistent thickness. It can be adjusted

to 24 settings, from very ﬁne (0.3mm) to thick

(8.0mm). To adjust the slicing thickness, hold

the adjustable slicing disc by the outer edge

with one hand, keeping hand away from blade,

and turn the adjustment dial on the underside

with the other hand. An arrow graphic

indicates the thickness of the slice you

have chosen.

Reversible grater and shredder

This disc has an array of small blades on both

sides of the disc. Align the disc so larger holes

face up for coarser textured results, or with the

smaller holes facing up for ﬁner results. The

discs are labelled showing which side faces up.

La page charge ...

Breville the Breville Sous Chef 16 Peel & Dice Manuel utilisateur

Breville the Breville Sous Chef 16 Peel & Dice Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents