NAPOLEON EPI-1101M Manuel utilisateur

Marque: NAPOLEON

Modèle: EPI-1101M

Catégorie: Poêles

Taper: Manuel utilisateur

Ce manuel convient également à

EPI-1402M

W415-1469 / C / 08.20.18

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

NEVER LEAVE CHILDREN OR OTHER AT RISK INDIVIDUALS ALONE WITH THE APPLIANCE.

This wood appliance needs periodic inspection and repair for proper operation. It is against United States federal

regulation to operate this wood appliance in a manner inconsistent with operating instructions in this manual.

INSTALLATION AND

OPERATING INSTRUCTIONS

1.27D

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /

103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone (705)721-1212 • Fax (705)720-9081 • www.napoleonﬁ replaces.com • hearth@napoleonproducts.com

SAFETY INFORMATION

WARNING

If the information in these instructions is not followed exactly, a

ﬁ re or explosion may result causing property damage, personal

injury or death. Improper installation, adjustment, alteration,

service or maintenance can cause injury or property damage,

bodily injury or even death. Please read entire manual before

you install and use your appliance.

This appliance has not been tested with an unvented gas log

set. To reduce risk of ﬁ re or injury, do not install an unvented

gas log set into the appliance.

- This appliance can be very hot when burning.

- Combustible materials such as ﬁ rewood, wet clothing, etc. placed too close

can catch ﬁ re.

Children and pets must be kept from touching the appliance when it is hot.

The chimney must be sound and free of cracks. Before installing this unit,

contact the local building or ﬁ

re authority and follow their guidelines.

- Operate only with the door tightly closed.

Burn wood behind the log r

etainer directly on the ﬁ rebricks.

Do not use an elevated grate or otherwise raise the ﬁ

re.

At least 14 square inches (90.3 square centimeters) of outside air must be

admitted to the room or dir

ectly to the unit through a 4” (101.6mm) diameter

pipe.

- This appliance is designed to burn natural wood only. Higher efﬁ ciencies and

lower emissions generally result when burning air dried seasoned hardwoods,

as compared to softwoods or to green or freshly cut hardwoods.

Do not start a ﬁ

re with chemicals or ﬂ uids such as gasoline, engine oil, etc.

- Do not burn trash or garbage, lawn clippings / waste, rubber, waste petroleum

products, paints or paint thinners / solvents, plastic, materials containing

asbestos, construction debris, railroad ties or treated wood, manure or animal

remains, salt water driftwood or salted materials, unseasoned wood, coal,

charcoal, coloured paper, cardboard, plywood or particleboard.

- Do not let the appliance become hot enough for any part to glow red.

- KEEP THE STOVE TOP TEMPERATURE BELOW 700°F (371°C). Attempts to

achieve heat output rates that exceed design speciﬁ cations can result in steel

distortion and damage.

$10.00

LA VITRE CHAUDE CAUSERA

DES BRÛLURES.

NE PAS TOUCHER LA VITRE

AVANT QU’ELLE AIT REFROIDI.

NE JAMAIS LAISSER LES

ENFANTS TOUCHER LA VITRE.

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

WARNING

AVERTISSEMENT

MODEL 1101 & 1402 MEET THE 2015 U.S ENVIRONMENTAL PROTECTION AGENCY (E.P.A.) CRIB WOOD EMISSION LIMITS FOR WOOD STOVES SOLD AFTER MAY

15, 2015, 40 C.F. R. PART 60. THESE STOVES HAVE BEEN TESTED AND LISTED BY INTERTEK TESTING SERVICES TO STANDARDS:

ULC S628, UL 1482.

EPI 1101 & 1402

WOOD INSERT

1402 Illustrated

W415-1469 / C / 08.20.18

NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.

TABLE OF CONTENTS

1.0 INSTALLATION OVERVIEW 3

2.0 INTRODUCTION 4

2.1 DIMENSIONS 5

2.1.1 1101 DIMENSIONS (COMPLETE WITH FLASHING) 5

2.1.2 1402 DIMENSIONS (COMPLETE WITH FLASHING) 5

2.2 SPECIFICATIONS 5

2.3 GENERAL INSTRUCTIONS 6

2.4 GENERAL INFORMATION 6

2.5 RATING PLATE INFORMATION 8

3.0 INSTALLATION PLANNING 9

3.1 MINIMUM CLEARANCE TO COMBUSTIBLES 9

4.0 INSTALLATION 10

4.1 TYPICAL EXISTING MASONRY 11

4.2 FACTORY BUILT FIREPLACE 12

4.3 LOW CLEARANCE FLUE CONNECTOR (1402) 12

5.0 FINISHING 13

5.1 BRICKS AND BAFFLES INSTALLATION 13

5.2 DOOR REMOVAL / INSTALLATION 14

5.3 DOOR HANDLE INSTALLATION 14

5.4 FLASHING INSTALLATION 15

6.0 OPERATION 16

6.1 OPTIMUM BURN METHOD 17

6.2 BLOWER 18

6.3 AIR CONTROL 18

6.4 FIRE EXTINGUISHERS / SMOKE & CARBON MONOXIDE DETECTORS 18

6.5 FUEL 19

6.6 LIGHTING A FIRE 20

6.6.1 FLASH FIRE 20

6.6.2 EXTENDED FIRE 20

6.7 SMOKING 20

7.0 MAINTENANCE 21

7.1 ASH REMOVAL PROCEDURES 21

7.2 CREOSOTE FORMATION AND REMOVAL 21

7.3 RUNAWAY OR CHIMNEY FIRE 22

7.4 CHIMNEY CLEANING 22

7.5 GLASS REPLACEMENT 23

7.6 GASKET REPLACEMENT 23

7.7 SECONDARY AIR MANIFOLD REPLACEMENT 24

7.8 CARE OF GLASS 25

7.9 CARE OF PLATED PARTS 25

7.10 BLOWER SERVICE OR REPLACEMENT (1402) 26

7.11 BLOWER SERVICE OR REPLACEMENT (1101) 27

8.0 REPLACEMENTS 27

8.1 EPI-1402 OVERVIEW 28

8.2 EPI-1101 OVERVIEW 29

9.0 ACCESSORIES 30

10.0 TROUBLESHOOTING 31

11.0 WARRANTY 32

12.0 SERVICE HISTORY 33

W415-1469 / C / 08.20.18

Rating plate, see

“RATING PLATE

INFORMATION”

section.

Blower, see “BLOWER INSTALLATION”

section.

Door, see “DOOR AND

HANDLE INSTALLATION”

section.

Flashing, see “FLASHING

INSTALLATION” section.

Draft, see “AIR CONTROL” section.

Brick and Baffles, see

“BRICK AND BAFFLES

INSTALLATION” section.

1.0 INSTALLATION OVERVIEW

1402 Illustrated

W415-1469 / C / 08.20.18

2.0 INTRODUCTION

3.17G

WARNING

• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF CONTACTED.

• ANY CHANGES OR ALTERATIONS TO THIS APPLIANCE OR ITS CONTROLS CAN BE DANGEROUS AND

IS PROHIBITED.

• Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance

according to operating instructions could cause ﬁ re or injury.

• Before installing this appliance, contact the local building or ﬁ re authority and follow their guidelines.

• This appliance must be installed by a qualiﬁ ed installer.

• Risk of burns. The appliance should be turned off and cooled before servicing.

• Do not operate without fully assembling all components.

• Do not let the appliance become hot enough for any part to glow red.

• Do not install damaged, incomplete or substitute components.

• Risk of cuts and abrasions. Wear protective gloves and safety glasses during installation. Sheet metal edges may

be sharp.

• Children and adults should be alerted to the hazards of high surface temperature and should stay away to avoid

burns or clothing ignition.

• Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young

children and others may be susceptible to accidental contact burns. A physical barrier is recommended if there

are at risk individuals in the house. To restrict access to an appliance or stove, install an adjustable safety gate to

keep toddlers, young children and other at risk individuals out of the room and away from hot surfaces.

• Clothing or other ﬂ ammable material should not be placed on or near the appliance. Objects placed in front of the

appliance must be kept a minimum of 4 feet (1.2m) away from the front face of the appliance.

• Due to high temperatures, the appliance should be located out of trafﬁ c and away from furniture and draperies.

• Ensure you have incorporated adequate safety measures to protect infants/toddlers from touching hot surfaces.

• Even after the appliance is out, the glass and / or screen will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children from hot

surfaces. These screens and guards must be fastened to the ﬂ oor.

• Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.

• Under no circumstances should this appliance be modiﬁ ed.

• This appliance must not be connected to a chimney ﬂ ue pipe servicing a separate solid fuel burning appliance.

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass should

be done by a licensed or qualiﬁ ed service person.

• Do not strike or slam shut the appliance glass door.

• Only doors / optional fronts certiﬁ ed with the appliance are to be installed on the appliance.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with all

plastic bags, these are not toys and should be kept away from children and infants.

• If the appliance is not properly installed, a house ﬁ re may result. Do not expose the appliance to the elements (ex.

rain, etc.) and keep the appliance dry at all times. Wet insulation will produce an odour when the appliance is used.

• The chimney must be sound and free of cracks. Clean your chimney a minimum of twice a year and as required.

• Do not start a ﬁ re with chemicals or ﬂ uids such as gasoline, engine oil, etc.

• Your appliance requires periodic maintenance and cleaning. Failure to maintain your appliance may lead to smoke

spillage in your home.

• Lower emissions generally result when burning air dried seasoned hardwoods, as compared to softwoods or too

green or freshly cut hardwoods. Burning wet unseasoned wood can cause excessive creosote accumulation.

When this is ignited it can cause a chimney ﬁ re that may result in a serious house ﬁ re.

• This appliance is designed to burn natural wood only. Do not burn trash or garbage, lawn clippings / waste,

rubber, waste petroleum products, paints or paint thinners / solvents, plastic, materials containing asbestos,

construction debris, railroad ties or treated wood, manure or animal remains, salt water driftwood or salted

materials, unseasoned wood, coal, charcoal, coloured paper, gift wrapping, cardboard, plywood or particleboard.

Burning these materials may result in release of toxic fumes or render the appliance ineffective and cause smoke.

• Burn wood directly on the ﬁ rebricks. Do not elevate grate or otherwise raise the ﬁ re.

• Do not store wood within appliance installation clearances or within the space required for re-fueling and ash removal.

• Ashes must be disposed in a metal container with a tight lid and placed on a non-combustible surface well away

from the home or structure until completely cool.

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance.

Elevated temperatures on the wall or in the air above the appliance can cause melting, discolouration or damage to

decorations, a T.V. or other electronic components.

• If equipped, the catalyst must be installed and in good working order. It is recommended that the catalyst is

inspected at least 3 times per heating season.

W415-1469 / C / 08.20.18

* As tested using test method 28

** Figures will vary considerably with individual conditions.

***Wolf Steel Ltd. estimated realistic BTU/hr with hardwood logs and regular refueling.

Speciﬁcations 1101 1402

CHAMBER (D.W.H) 13 1/2x18x12" (343mmx-

457mmx305mm)

18x18x12" (457mmx457mmx-

305mm)

CAPACITY 1.7 ft

2.25 ft

APPROX. AREA HEATED** 600-1600 ft

800-2000 ft

MAXIMUM HEAT OUTPUT*** 55,000 BTU/Hr 70,000 BTU/Hr

HEAT OUTPUT* 11,700 - 42,200 BTU/Hr 11,400 - 41,300 BTU/Hr

DURATION LOW FIRE** 7 Hours 9 Hours

WEIGHT W/O BRICKS 185 lbs (84kg) 250 lbs (113kg)

WEIGHT OF BRICKS 110 lbs (50kg) 145 lbs (66kg)

IDEAL FUEL SIZE 12" (305mm) 16" (406mm)

MINIMUM DEPTH 16 1/2" (419mm) 14" (356mm)

MAXIMUM DEPTH 21" (533mm) 14" (356mm)

2.1 DIMENSIONS

2.1.1 1101 DIMENSIONS (COMPLETE WITH FLASHING)

2.1.2 1402 DIMENSIONS (COMPLETE WITH FLASHING)

44 1/2"

1130mm

19 3/4"

502mm

31 3/4"

806mm

21 1/2"

546mm

20 3/4"

527mm

14"

356mm

9 1/16"

231mm

24 1/2"

622mm

25 1/2"

648mm

5 1/2"

139mm

25 1/2"

648mm

21 11/16"

551mm

20 1/2"

521mm

31 3/4"

806mm

44 1/2"

1130mm

21 1/4"

540mm

16 1/2"

419mm

21"

533mm

28"

711mm

24"

610mm

11"

279mm

25 1/2"

648mm

21 11/16"

551mm

20 1/2"

521mm

2.2 SPECIFICATIONS

W415-1469 / C / 08.20.18

2.3 GENERAL INSTRUCTIONS

• Before beginning your installation, consult with your local building code agency or ﬁre ofﬁcials and insur-

ance representative to ensure compliance.

• Non-toxic smoke will be emitted during the paint curing process, to help dissipate the smoke open a

window near the appliance.

• Remove any dust or debris off the top of the appliance before ﬁring the appliance as the paint will become

soft as the appliance heats up and will harden as the appliance cures. To cure the paint on your appliance

burn your appliance moderately hot during the ﬁrst few ﬁres.

• To keep the gasket from sticking to the appliance as the paint is curing, periodically open the door every

5-10 minutes.

• For the ﬁrst two weeks, use generous amounts of fuel and burn the appliance with the damper wide open

for an hour as the appliance goes through a process of eliminating moisture in the steel and ﬁrebricks.

The initial heat output will be reduced while the moisture is bring drawn from the appliance and it will

be necessary to build several hot ﬁres to remove this moisture. DURING THIS PROCESS DO NOT

OVERFIRE THE APPLIANCE. REDUCE THE AMOUNT OF AIR COMING INTO THE APPLIANCE IF

THE APPLIANCE OR CHIMNEY BECOMES RED.

4.7

ALL WIRING SHOULD BE DONE BY A QUALIFIED ELECTRICIAN AND SHALL BE IN COMPLIANCE WITH

LOCAL CODES. IN THE ABSENCE OF LOCAL CODES, USE THE CURRENT CSA22.1 CANADIAN

ELECTRIC CODE IN CANADA OR THE CURRENT NATIONAL ELECTRIC CODE ANSI/NFPA NO. 70 IN

THE UNITED STATES.

THIS APPLIANCE HAS NOT BEEN TESTED WITH ANY VENTED OR UNVENTED GAS LOG SET. TO

REDUCE RISK OF FIRE OR PREVENT INJURY, DO NOT INSTALL A VENTED OR UNVENTED GAS LOG

SET INTO THE APPLIANCE.

BURNING YOUR UNIT WITH THE ASH DUMP DOOR OPEN OR AJAR CREATES A FIRE HAZARD THAT

MAY RESULT IN DISCOLOURATION TO THE GOLD PLATED DOOR, INTERNAL DAMAGE TO THE

APPLIANCE OR A HOUSE CHIMNEY FIRE.

DO NOT CONNECT THIS APPLIANCE TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

THIS APPLIANCE AND IT’S COMPONENTS ARE DESIGNED TO BE INSTALLED AND OPERATED AS A

SYSTEM. ANY ALTERATION TO OR SUBSTITUTION FOR ITEMS IN THIS SYSTEM, UNLESS ALLOWED

BY THESE INSTALLATION INSTRUCTIONS, WILL VOID THE LISTING AND MAY VOID THE PRODUCT

WARRANTY. IT MAY ALSO CREATE A HAZARDOUS INSTALLATION. READ THROUGH THESE

INSTRUCTIONS THOROUGHLY BEFORE STARTING YOUR INSTALLATION AND FOLLOW THEM

CAREFULLY THROUGHOUT YOUR PROJECT.

WARNING

Your appliance was speciﬁcally designed to meet the 1990 U.S.A. EPA particulate emission standards and has

been extensively tested in Canadian and American laboratories. This system is the most efﬁcient, simple and

trouble free we know and works as follows:

Your appliance is the exact duplication of the clean-burning technology found in all Napoleon EPA certiﬁed freestanding

stoves and in particular that of the EPA 1100 and 1400. External modiﬁcations have been made to allow its installation as a

“functional insert” with a heat circulating blower system and a means of enclosing the solid fuel burning ﬁreplace cavity for

greater heating efﬁciency.

2.4 GENERAL INFORMATION

W415-1469 / C / 08.20.18

The 1101 insert must be installed into a solid fuel burning ﬁreplace that is at least 16 1/2” (419mm) deep, 28 1/2" (724mm)

wide and 22" (559mm) high with an approved lined chimney at least 15' (4.6m) high and a hearth of 16” (406mm).

Your 1402 insert must be installed only into a solid fuel burning ﬁreplace that is at least 14" (356mm) deep, 26" (660mm)

wide and 22" (559mm) high with an approved lined chimney at least 15' (4.6m) high and a hearth of 16” (406mm). This

minimum recess can only be achieved if the opening height is sufﬁcient enough to allow the connector to ﬁt under the

non-combustible facing. The appliance and chimney must be constructed in accordance with all national and local building

code standards.

The chimney vent system used on your wood burning appliance should be designed with the least amount of restriction

possible to enable the exhaust products to easily ﬂow through it. Chimney vent systems that are too short or too long

can also have an adverse affect on the ﬂow of exhaust through it. The wood burning appliance and chimney vent

system also require a sufﬁcient supply of combustion air not only to support the combustion in the combustion chamber

but to replace the exhaust leaving it so it can ﬂow freely up through the vent system and out into the atmosphere. It is

the correct balance of combustion air and the chimney vent system that will ensure the appliance provides you with its

optimum performance.

Combustion air enters through two holes in the bottom covered by a single draft control. Air from the front hole

goes up on either side of the door into a preheating

airwash located across the top and then down the

window to feed the ﬁre and also to ensure that the glass

remains clean. Air from this hole also feeds directly into

the combustion chamber at hearth level. Secondary air

from the rear hole travels up the back in the secondary air

housing to the manifold located at the top and shoots out

laterally to oxidize the gases below the smoke exit.

The combustion chamber is lined with high temperature

ﬁrebrick on 2 sides, the back and across the bottom,

with a layer of ﬁbre bafﬂes at the top to maintain a high

temperature in the combustion chamber so that gases

mixing with the preheated air from the secondary air

manifold tube are easily ignited and burned. The appliance

sides and back are shielded to direct the heat upwards

and forwards into the room.

Be sure to provide sufﬁcient combustion air. There are

many other appliances in your home competing for air

such as: a kitchen range hood, forced air heating devices

or a bathroom exhaust fan.

Expansion / contraction noises during heating up and cooling down cycles are normal and to be expected.

After extended periods of non-operation such as following a vacation or a warm weather season, the appliance

may emit a slight odour for a few hours. This is

caused by dust particles on the ﬁrebox burning off.

Open a window to sufficiently ventilate the room.

If you experience smoking problems, you may

need to open a door, a window or otherwise

provide some method of supplying combustion air to the appliance.

HINT FOR INSTALLING PORCELAIN ENAMEL INSERTS:

Ensure the base of the porcelain side panels are protected from rubbing against the hearth when sliding your

insert into the masonry ﬁreplace.

HOT SECONDARY AIR

FIBRE BRICKS

REFRACTORY

2 SIDES, BACK

& BOTTOM

SECONDARY AIR

PRIMARY AIR

FLUE GLASS

CERAMIC

GLASS

AIR CONTROL

COMBUSTION AIR

INTAKE

OPEN

CLOSED

We suggest that our woodburning hearth products

be installed and serviced by professionals who are

certified in the U.S. by the National Fireplace

Institute® (NFI) as NFI Woodburning Specialists or

who are certified in Canada by

Wood Energy Technical

Training (WETT).

W415-1469 / C / 08.20.18

2.5 RATING PLATE INFORMATION

WOLF STEEL LTD

TITLE: RATING PLATE LABEL EPA1400

REVISION: B

DRAWN BY: J.K.

CHECKED BY: 11.08.16_C.L.

MATERIAL:

CLASS III A-2 PERMANENT LABEL

MM/DD/YY: 11.08.16

MODEL: S4, 1400, 1400L, 1402, 1450, 1400C

DRAWING: W385-2031

FINISH:

MM/DD/YY: 03.18.16

SHEET 1 0F 1

MAXIMUM SIZE: 6" x 11.250"

SILVER ON BLACK BACKGROUND

SPECIFICATIONS: WATERPROOF, NONWATER SOLUBLE ADHESIVE CAPABLE OF WITHSTANDING A MAXIMUM

TEMPERATURE OF 175°F (79°C).

SERIAL NUMBER TO BE ASCENDING FROM EPA1400

117839

CAUTION MINIMUM LETTER SIZE (18 POINT TYPE) AND 0.12" (8.64 POINT TYPE) FOR THE REMAINDER OF

THAT WARNING WITH VERTICAL SPACING BETWEEN LINES OF 0.046" (3.312 POINT TYPE).

LOG / FIRE WARNING SYMBOL TO BE RED

LISTED SOLID FUEL BURNING FIREPLACE INSERT /

ENCASTRÉ À COMBUSTIBLE SOLIDE HOMOLOGUÉ

TESTED TO / TESTÉ SELON :

ULC S628 / UL 1482

FROM HEATER / DU POÊLE

RESIDENTIAL / RÉSIDENTIEL

16IN/PO (406 mm)

12IN/PO (305 mm)

6IN/PO (152 mm)

USING DOUBLE WALL CONNECTOR /

UTILISATION D’UN CONDUIT DE

RACCORDEMENT À DOUBLE PAROI

MAISON / MOBILE HOME

1400

16IN/PO (406 mm)

10IN/PO (254 mm)

6IN/PO (152 mm)

4IN/PO (102 mm)

EPI 1402

INSTALL AND USE ONLY IN

ACCORDANCE WITH THE

MANUFACTURER’S

INSTRUCTIONS AND LOCAL

BUILDING CODES.

MINIMUM CEILING HEIGHT:

7FT (2.13m)

HEARTH EXTENSION /

COMBUSTIBLE FLOOR

PROTECTION: IF INSTALLED

ON A COMBUSTIBLE FLOOR,

APPLIANCE MUST BE PLACED

ON A NON-COMBUSTIBLE

FLOOR PROTECTOR

EXTENDING 18” (455mm) IN

FRONT AND 8” (205mm) TO

THE SIDES AND BACK.

CHIMNEY TYPE: MINIMUM 6”

(152mm) DIAMETER

APPROVED RESIDENTIAL

TYPE FOR MOBILE HOME USE

A CHIMNEY LISTED TO ULC

S629 IN CANADA OR UL 103HT

IN THE USA.

CHIMNEY CONNECTOR: 6”

(152mm) DIAMETER MINIMUM

24 GAUGE STEEL MINIMUM

CLEARANCE FROM

HORIZONTAL CONNECTOR

AND CEILING 18” (455mm).

DO NOT OBSTRUCT SPACE

UNDER APPLIANCE.

SPECIAL METHODS ARE

REQUIRED WHEN PASSING A

CHIMNEY THROUGH A WALL

OR CEILING. SEE INSTRUC-

TIONS AND BUILDING CODES.

DO NOT CONNECT THIS

APPLIANCE TO A CHIMNEY

FLUE SERVING ANOTHER

APPLIANCE.

FUEL: FOR USE WITH WOOD

ONLY. DO NOT USE GRATE OR

ELEVATE FIRE. BUILD WOOD

FIRE DIRECTLY ON HEARTH.

WARNING: RISK OF SMOKE

SPILLAGE. OPERATE ONLY

WITH DOOR FULLY CLOSED.

REPLACE GLASS ONLY WITH

CERAMIC GLASS.

DO NOT OVERFIRE. IF

APPLIANCE OR CHIMNEY

CONNECTORS GLOW, YOU

ARE OVERFIRING. INSPECT

AND CLEAN CHIMNEY

FREQUENTLY. UNDER

CERTAIN CONDITIONS OF

USE CREOSOTE BUILD-UP

MAY OCCUR RAPIDLY.

OPTIONAL BLOWER KIT:

EP-62, 115V, 60HZ, 0.82AMP.

ROUTE CORD AWAY FROM

APPLIANCE.

DANGER: RISK OF

ELECTRICAL SHOCK.

DISCONNECT POWER

BEFORE SERVICING

APPLIANCE.

INSERT: INSTALL AND USE

ONLY IN SOLID FUEL

BURNING FIREPLACES. DO

NOT REMOVE BRICKS OR

MORTAR FROM SOLID FUEL

BURNING FIREPLACE.

INSTALL WITH A POSITIVE

FLUE CONNECTOR AND

FACEPLATE.

POUR INSTALLATION ET

UTILISATION CONFORM

ÉMENT AUX

INSTRUCTIONS DU FABRICANT ET

AUX CODES LOCAUX DU BÂTIMENT.

HAUTEUR DE PLAFOND MINIMAL

7PI (2,13m).

PROLONGEMENT

D’ÂTRE/PROTECTION DU

PLANCHER COMBUSTIBLE: SI

INSTALLÉ SUR UN PLANCHER

COMBUSTIBLE, L’APPAREIL DOIT

ÊTRE PLACÉ SUR UNE PLAQUE

PROTECTRICE INCOMBUSTIBLE

S’ÉTENDANT SUR 18” (455mm)

L’AVANT ET 8” (205mm) À L’ARRIÈRE

ET SUR LES CÔTÉS.

TYPE DE CHIMNÉE: DIAMÈTRE

MINIMAL DE 6” (152mm)

APPROUVÉE POUR USAGE

RÉSIDENTIEL. MAISON MOBILE

EMPLOYEZ UNE CHEMINÉE

HOMOLOGUÉE ULC S629 AU

CANADA OU UL 103HT AUX

ÉTATS-UNIS.

RACCORD DE CHEMINÉE:

DIAMÈTRE DE 6” (152mm) D’ACIER

DE CALIBRE 24 MINIMUM. 18”

(455mm) DE DÉGAGEMENT MINIMAL

ENTRE LE RACCORD HORIZONTAL

ET LE PLAFOND.

NE RIEN ENTREPOSER SOUS

L’APPAREIL.

DES MÉTHODES SPÉCIALES SONT

REQUISES LORSQU’UNE CHEMINÉE

TRAVERSE UN MUR OU UN

PLAFOND. VOIR LES INSTRUC-

TIONS ET LES CODES DU

BÂTIMENT.

NE PAS RACCORDER À LA

CHEMINÉE D’UN AUTRE APPAREIL.

COMBUSTIBLE: POUR USAGE AVEC

LE BOIS SEULEMENT. N’UTILISEZ

PAS DE CHENET OU NE

SURÉLEVEZ PAS LE BOIS.

PRÉPAREZ LE FEU DIRECTEMENT

SUR L’ÂTRE.

AVERTISSEMENT: RISQUE

D’ÉCHAPPEMENT DE FUMÉE. TENIR

LA PORTE FERMÉE LORSQUE LE

POÊLE FONCTIONNE. REMPLACEZ

LA VITRE PAR UNE VITRE EN

CÉRAMIQUE SEULEMENT.

NE SURCHAUFFEZ PAS L’APPAREIL.

SI L’APPAREIL OU LES RACCORDS

ROUGEOIENT, L’APPAREIL

SURCHAUFEE. INSPECTEZ ET

NETTOYEZ LA CHEMINÉE

FRÉQUEMMENT. DANS CERTAINES

CONDITIONS, DES DÉPÔTS DE

CRÉOSOTE PEUVENT SE FORMER

RAPIDEMENT.

SOUFFLERIE OPTIONNELLE: EP-62,

115V, 60HZ, 0,82A. TENEZ LE

CORDON ÉLECTRIQUE LOIN DE

L’APPAREIL.

DANGER: RISQUE DE SECOUSSE

ÉLECTRIQUE. DÉBRANCHEZ AVANT

DE PROCÉDER À L’ENTRETIEN.

ENCASTRÉ: INSTALLEZ ET UTILISEZ

SEULEMENT DANS UN FOYER À

COMBUSTIBLE SOLIDE. NE RETIREZ

PAS DE MORTIER, NI BRIQUES DU

FOYER À COMBUSTIBLE SOLIDE.

INSTALLEZ AVEC UNE GAINE

CONFORME ET UNE PLAQUE DE

RECOUVREMENT.

CONTACT LOCAL BUILDING FIRE OFFICIALS ABOUT RESTRICTIONS AND

INSTALLATION INSPECTION IN YOUR AREA. MODEL 1400 IS SUITABLE FOR USE

IN MOBILE HOMES WHEN USED WITH OUTSIDE AIR INSTALLATION KIT (111KT).

A MINIMUM CLEARANCE OF 18” (457mm) TO THE CHIMNEY CONNECTOR MAY

BE REQUIRED BY THE AUTHORITY HAVING JURISDICTION.

RENSEIGNEZ-VOUS AUPR

ÈS DES AUTORITÉS LOCALES DU BÂTIMENT ET DU

SERVICE DES INCENDIES AU SUJET DES RESTRICTIONS ET DES INSPECTIONS

D’INSTALLATION DANS VOTRE RÉGION. LES MODÈLES 1400 PEUVENT ÊTRE

INSTALLÉS DANS UNE MAISON MOBILE SI INSTALLÉS CONJOINTEMENTAVEC UNE

PRISE D’AIR EXTÉRIEUR (111KT). UN DÉGAGEMENT MINIMAL DE 18” (457mm)

JUSQU’AU RACCORD DE LA CHEMINÉE PEUT ÊTRE EXIGÉ PAR L’AUTORITÉ AYANT

JURIDICTION.

18"

ALCOVE

BACK WALL (M/A)

45°

SIDE WALL (M/L)

BACK WALL (M/A)

SIDE WALL (M/L)

IF THE STOVE IS TO BE INSTALLED ON A COMBUSTIBLE FLOOR, IT MUST BE

PLACED ON AN APPROVED NON-COMBUSTIBLE HEARTH PAD, THAT

EXTENDS 8” (200mm) BEYOND THE STOVE SIDES AND BACK, AND 18”

(455mm) TO THE FRONT.

SI LE PO

LE EST INSTALL

É SUR UN PLANCHER COMBUSTIBLE, IL DOIT ÊTRE PLACÉ

SUR UNE BASE DE PROTECTION INCOMBUSTIBLE CERTIFÉE QUI DOIT DÉPASSER

LES CÔTÉS ET L’AMÉRE DU

LE DE 8” (200mm) ET SE PROLONGER DE 18”

(455mm) SUR LE DEVANT.

MINIMUM CLEARANCE TO COMBUSTIBLE MATERIAL WITH SINGLE WALL

CHIMNEY CONNECTOR / D

ÉGAGEMENTS MINIMAUX AUX MATÉRIAUX

COMBUSTIBLES AVEC RACCORD DE CHEMINÉE À PAROI SIMPLE:

ONLY MODELS 1400 AND S4 MAYBE INSTALLED INTO A MOBILE HOME OR

COMBUSTIBLE ALCOVE USING LISTED DOUBLE WALL CONNECTOR. MODELS

1400 AND S4 MAY BE INSTALLED INTO A MOBILE HOME IN THE UNITED

STATES ONLY.

LE MODÈLES 1400 ET S4 NE PEUT ÊTRE INSTALLÉ QUE DANS UNE MAISON

MOBILE AUX ÉTATS-UNIS SEULEMENT.

HOT WHILE IN OPERATION. DO NOT TOUCH. KEEP CHILDREN,

CLOTHING AND FURNITURE AWAY. CONTACT MAY CAUSE

SKIN BURNS.

QUAND L’APPAREIL FONCTIONNE, LA SURFACE DEVIENT

CHAUDE. NE PAS TOUCHER. TENIR LES ENFANTS, LES

VÊTEMENTS ET LES MEUBLES À L’ÉCART. LE CONTACT PEUT

CAUSER DES BRÛLURES À LA PEAU.

CAUTION:

ATTENTION:

W385-2031 / B

EPA1400

1400 1400L 1402

1450

WOLF STEEL LTD.

24 NAPOLEON ROAD, BARRIE, ON, L4M 0G8 CANADA

1400C

9700539 (WSL)

4001657 (NGZ)

4001658 (NAC)

4001659 (WUSA)

LISTED SOLID FUEL BURNING SPACE HEATER / POÊLE À COMBUSTIBLE SOLIDE

HOMOLOGUÉ TESTED TO: / TESTÉ SELON : UL1482 / ULC S627

MODEL / MODÈLE - EPA 1400

U.S. ENVIRONMENTAL PROTECTION AGENCY

Certified to comply with 2015 particulate emissions standards. Not approved for sale

after May 15, 2020. Certifié conforme à la norme d’ émanation de particles de 2020. Non approuvé pour la vente après le 15 mai, 2020.

40 CFR Part 60,Subpart AAA.

1400

12IN/PO (305 mm) A

12IN/PO (305 mm)

6IN/PO (152 mm)

1400

10IN/PO (254 mm)

6IN/PO (152 mm)

4IN/PO (102 mm)

16IN/PO (406 mm)

6IN/PO (152 mm)

4IN/PO (102mm)

CEILING / PLAFOND

FLOOR / PLANCHER

CLEARANCES TO COMBUSTIBLE CONSTRUCTION /

ÉGAGEMENTS AUX MATÉRIAUX COMBUSTIBLES:

(MEASURED TO UNIT / À PARTIR DE L’APPAREIL)

A SIDE FACING / CÔTÉ 1 IN/PO (25mm)

B TOP FACING / DESSUS 28 IN/PO (710mm)

C MANTEL / TABLETTE 28 IN/PO (710mm)

D SIDE WALL / MUR LATÉRAL 17 IN/PO (430mm)

CLEARANCE TO EDGE OF FLASHING / DÉGAGEMENT AU

BORD DE LA FAÇADE

3.5 Grams Per Hour / 2015 Crib Wood / 3.5 Grammes par heure / Crib Wood 2015

MANUFACTURE DATE: / DATE DE FABRICATION:

YEAR:

2016

2017

2018

MONTH:

2019

2020

2 43 65 87 109 1211

THIS WOOD APPLIANCE NEEDS PERIODIC INSPECTION AND REPAIR FOR

PROPER OPERATION. CONSULT THE OWNER'S MANUAL FOR FURTHER

INFORMATION. IT IS AGAINST UNITED STATES FEDERAL REGULATIONS TO

OPERATE THIS WOOD APPLIANCE IN A MANNER INCONSISTENT WITH THE

OPERATING INSTRUCTIONS IN THE OWNER'S MANUAL.

CET APPAREIL AU BOIS DOIT FAIRE L'OBJECT D'UNE INSPECTION ET D'UN

ENTRETIEN PÉRIODIQUES POUR UN FONCTIONNEMENT ADÉQUAT. CONSULTEZ

LE MANUEL D'INSTRUCTIONS POUR PLUS D'INFORMATION. LES RÈGLEMENTS

FÉDÉRAUX DE L'ÉTATS-UNIS INTERDISENT D'UTILISER CET APPAREIL DE

CHAUFFAGE D'UNE MANIÈRE ALLANT À L'ENCONTRE DES INSTRUCTIONS DE

FONCTIONNEMENT CONTENUES DANS CE MANUEL.

CORRECTED ADHESIVE TEMPERATURE LIMIT

1400 SERIES RATING PLATE ILLUSTRATED

For rating plate location, see

“INSTALLATION OVERVIEW” section.

This illustration is for reference

only. Refer to the rating plate on the

appliance for accurate information.

NOTE: The rating plate must remain

with the appliance at all times. It

must not be removed.

SAMPLE

W415-1469 / C / 08.20.18

3.0 INSTALLATION PLANNING

Clean all ashes out of the inside of the existing ﬁreplace opening. Make sure that the chimney and ﬁreplace are free

of cracks, loose mortar, creosote deposits, blockage or other signs of deterioration. If necessary, have any repair

work done by a qualiﬁed professional before installing the insert.

Do NOT remove bricks or mortar from the ﬁreplace. In case of an outside air inlet or ash dump, ﬁll with ﬁberglass

insulation. Adhere to minimum clearances as illustrated.

Do NOT place any combustible materials (furniture, ﬁrewood, etc.) within 48"(121.9cm) in front of 36" (91.4cm) at the

sides of the insert.

Combustible material must not protrude more than 1" (25mm) to the side of the insert or between the mantel and

the top of the insert.

SIDEWALL

COMBUSTIBLE MANTEL

NON-COMBUSTIBLE

FACING

NON-COMBUSTIBLE

HEARTH AND THERMAL

FLOOR PROTECTOR

NON-COMBUSTIBLE

FACING

COMBUSTIBLE MANTEL

NON-COMBUSTIBLE

HEARTH AND THERMAL

FLOOR PROTECTOR

MINIMUM CLEARANCES

1101 1402

Sidewall

17" (43.2cm) 17" (43.2cm)

Mantel

28" (71.1cm) 28" (71.1cm)

Top facing

28" (711mm) 28" (71.1cm)

Side facing

1" (25mm) 1" (25mm)

Hearth (front) Canada 18"

(45.5cm)

US 16" (40.6cm)

Canada 18"

(45.5cm)

US 16"(40.6cm)

Hearth (side)

8" (203mm) 8" (203mm)

Objects in

front of insert

48" (121.9cm) 48" (121.9cm)

MINIMUM FIREPLACE SIZE

Width (rear)

24" (61cm) 25" (63.5cm)

Width (front)

28.5" (72.4cm) 26" (66cm)

Height (front)

22" (55.8cm) 22" (55.8cm)

Height (rear)

22" (55.8cm) 22" (55.8cm)

Depth 16 1/2" (41.9cm) to

21" (53.3cm)

14 1/2" (36.8cm)

Hearth width

39" (99cm) 39" (99cm)

Facing width

46 1/2" (118.1cm) 46 1/2" (118.1cm)

Facing height

48 1/2" (123.2cm) 47 3/4" (121.3cm)

Mantel

48 1/2" (123.2cm) 47 3/4" (121.3cm)

3.1 MINIMUM CLEARANCE TO COMBUSTIBLES

HEARTH EXTENSION / FLOOR PROTECTION:

Must be non-combustible and extend in front of

the insert and 8" (203mm) on both sides with a

minimum thickness of 1/2" (13mm) and a thermal

conductivity factor (K) 0.84.

W415-1469 / C / 08.20.18

4.0 INSTALLATION

68.3C

WARNING

WEAR GLOVES AND SAFETY GLASSES FOR PROTECTION.

CAREFULLY FOLLOW THE INSTRUCTIONS FOR ASSEMBLY OF THE PIPE AND OTHER PARTS

NEEDED TO INSTALL THE APPLIANCE. FAILURE TO DO SO MAY RESULT IN A FIRE, ESPECIALLY IF

COMBUSTIBLES ARE TOO CLOSE TO THE APPLIANCE OR CHIMNEY AND AIR SPACES ARE

BLOCKED, PREVENTING THE FREE MOVEMENT OF COOLING AIR.

DO NOT DRAW OUTSIDE AIR FROM GARAGE SPACES. EXHAUST PRODUCTS OF GASOLINE ENGINES

ARE HAZARDOUS. DO NOT INSTALL OUTSIDE AIR DUCTS SUCH THAT THE AIR MAY BE DRAWN

FROM ATTIC SPACES, BASEMENTS OR ABOVE THE ROOFING WHERE OTHER HEATING APPLIANCES

OR FANS AND CHIMNEYS EXHAUST OR UTILIZE AIR. THESE PRECAUTIONS WILL REDUCE THE

POSSIBILITY OF APPLIANCE SMOKING OR AIR FLOW REVERSAL. THE OUTSIDE AIR INLET MUST

REMAIN CLEAR OF LEAVES, DEBRIS ICE AND/OR SNOW. IT MUST BE UNRESTRICTED WHILE

APPLIANCE IS IN USE TO PREVENT ROOM AIR STARVATION WHICH CAN CAUSE SMOKE SPILLAGE

AND AN INABILITY TO MAINTAIN A FIRE. SMOKE SPILLAGE CAN ALSO SET OFF SMOKE ALARMS.

NEGATIVE PRESSURE WITHIN YOUR HOME MAY INADVERTENTLY AFFECT YOUR APPLIANCE.

TO PREVENT CONTACT WITH SAGGING OR LOOSE INSULATION, THE APPLIANCE MUST NOT BE

INSTALLED AGAINST VAPOUR BARRIERS OR EXPOSED INSULATION. LOCALIZED OVERHEATING

COULD OCCUR AND A FIRE COULD RESULT.

DO NOT USE MAKESHIFT COMPROMISES DURING INSTALLATION. DO NOT BLOCK OR RESTRICT

AIR, GRILLE OR LOUVRE OPENINGS. DO NOT ADD A HOOD.

TO PREVENT PERSONAL INJURY KEEP HAND TOOLS IN GOOD CONDITION, SHARPEN CUTTING

EDGES AND MAKE SURE TOOL HANDLES ARE SECURE.

ALWAYS MAINTAIN THE MINIMUM AIR SPACE REQUIRED TO THE ENCLOSURE TO PREVENT FIRES.

Chimney and liner must be in good condition and kept clean.

W415-1469 / C / 08.20.18

You can install your appliance using your existing masonry chimney. To do

so, follow the guidelines below. If you are using a masonry chimney, it

is important that it be built in compliance with the speciﬁ cations of the

Building Code in your region. It must normally be lined with ﬁ re clay

bricks, metal or clay tiles sealed together with ﬁ re cement. (Round

ﬂ ues are the most efﬁ cient).

62.2

FOLLOW MANUFACTURER’S

INSTRUCTIONS FOR

MAXIMUM LINER EXTENSION

ABOVE CHIMNEY

FLOOR

PROTECTOR

DAMPER PLATE

REMOVED OR

FASTENED IN OPEN

POSITION

SEAL WITH NON-

COMBUSTIBLE

MATERIAL

MASONRY

CHIMNEY MUST

HAVE

STRUCTURAL

INTEGRITY

LISTED

CHIMNEY

LINER

A. Remove the ﬁreplace damper or fasten it permanently open.

* We recommend the following method of sealing off the damper area around the liner.

B. * Measure the throat of the ﬁreplace and mark this shape on a piece of 24 gauge sheet metal (ﬂue cover);

cut a six-inch (6 3/4" / 171mm) hole to lie directly below the ﬁreplace ﬂue opening. Allow two inches of

material for a ﬂange on all sides and cut to these measurements. Bend down the ﬂanges. If you have never

done this before, it might be a good idea to make a cardboard pattern and test it ﬁrst. Fasten this ﬂue cover

in position as high as possible with two masonry screws per side through the ﬂanges into the ﬁreplace.

In Canada: Install a listed 6" (152mm) diameter ﬂexible stainless steel liner from the top of the chimney to the insert

ﬂue collar. Attach a stainless steel liner connector or elbow to the liner and insert onto the ﬂue collar. Fasten with

three screws. Secure the top of the liner to the chimney cap using a liner support and chimney ﬂashing. Cap the top

of the chimney liner assembly using an approved rain cap.

In the United States: While it is not required, it is recommended that a chimney liner be installed that is continuous

from the insert to the top of the chimney, particularly when the insert is installed in a basement. For this type of con-

nection, use the “In Canada” installation instructions above.

If a continuous liner is not installed, a “direct ﬂue connection” must be made. The direct ﬂue connection requires a

non-combustible connector that extends from the insert into the chimney ﬂue liner and also that the installed ﬂue

cover be sealed below the entry point of the connector to prevent dilution of combustion products in the chimney

ﬂue with air from inside the house. Cap the top of the chimney using an approved rain cap.

DO NOT CONNECT THIS APPLIANCE TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE. DO

NOT CONNECT TO ANY AIR DISTRIBUTION DUCT OR SYSTEM.

WARNING

4.1 TYPICAL EXISTING MASONRY

W415-1469 / C / 08.20.18

An optional low clearance ﬂue connector is available to facilitate hook up into a tight ﬁtting ﬁreplace. Consult your lo-

cal dealer for details.

NOTE: This kit should be used in conjunction with a dripless connector between the ﬂue collar and ﬂex

liner.

A. Having ensured that the chimney is thoroughly

clean, install the ﬂex liner. Insert a dripless connec-

tor into the ﬂue collar. Attach the ﬂex liner to other

end of the adapter. Secure using 6 - #8 screws.

B. Coil the rope gasket around the insert ﬂue collar

sealing the gap between the collar and the insert

top. Using 4 - #8 screws, attach the collar ﬂange,

squeezing the gasket tightly into place.

C. Move the insert into place in the ﬁreplace. Maneu-

ver the insert clips into the two slots located on

the insert top by reaching through the insert ﬂue

collar from inside the insert.

D. Thread the #10 - 24 screw through the slot lo-

cated on the insert top and into the threaded hole on the ﬂue connector, allowing the ﬂue connector to be

drawn forward into place.

NOTE: Check for a good seal between the insert top and the ﬂue connector (by holding a ﬂashlight up

through the insert collar, etc.).

The following installation requirements must be observed when installing solid fuel burning inserts into factory

built ﬁ replaces.

A. The factory built ﬁ replace must be listed per UL 127 or ULC S610.

B. Clearances to any combustible material surrounding this insert as identiﬁ ed must be followed. These

clearance requirements supersede any pre-existing facing material clearances listed for the factory

built ﬁ replace.

C. Installation must include a full height listed chimney liner meeting HT requirements (2100°F/1149°C)

as required in UL 1777 (U.S.) or ULC S635 (Canada). The liner must be securely attached to the insert

ﬂ ue collar and the chimney top.

D. Means must be provided to prevent room air passage to the chimney cavity of the ﬁ replace. This may

be accomplished by sealing the damper area around the chimney liner, or sealing the appliance front.

E. The air ﬂ ow within and around the appliance shall not be altered by the installation of the insert (i.e.

no louvres or cooling air inlet or outlet ports are blocked), unless speciﬁ cally tested as such for each

factory built ﬁ replace manufacturer and model line. NOTE: Using a louvered face plate (surround)

complies with this requirement.

F. Alteration of the appliance in any manner is not permitted with the following exceptions;

A. External trim pieces which do not affect the operation of the appliance may be removed providing

they can be stored on or within the ﬁ replace for reassembly if the insert is removed.

B. The chimney damper may be removed to install the chimney liner.

G. Circulating air chambers (i.e. in a steel ﬁ replace liner or metal heat circulator) shall not be blocked.

H. Means must be provided for removal of the insert to clean the chimney ﬂ ue.

I. Inserts that project in front of the ﬁ replace must be supplied with appropriate support means.

J. A permanent metal warning label must be attached to the back of the ﬁ replace stating that the ﬁ replace

must be restored to its original condition for safe use without the insert.

80.2B

4.2 FACTORY BUILT FIREPLACE

4.3 LOW CLEARANCE FLUE CONNECTOR (1402)

W415-1469 / C / 08.20.18

5.0 FINISHING

A. Install (1101) four (A) bricks and one (C) brick or (1402) six (A) bricks along both sides of the appliance.

Before installing the back bricks, loosen the screw holding the retainer and ensure that it has been moved

forward. Install the four (A) bricks and two (D) bricks along the back wall by pivoting the bricks up under

the brick retainer. Retighten the screw. NOTE: Center (D) bricks have been notched.

B. Carefully pivot ﬁbre bafﬂe (G) and (H) up onto the top of the side brick. Slide it over onto the ﬂange of the

manifold. Ensure that the top bafﬂes are pushed all the way to the rear of the ﬁrebox, leaving a minimum

of a 1" (25mm) gap along the front. This will allow the ﬂue gases to escape the ﬁrebox.

C. Install the bottom (1101) four (A) bricks and two (B) bricks or (1402) six (A) bricks and two (B) bricks,

working from the back of the appliance forward.

D. Install the two (B) bricks, one (E) brick and one (F) brick along the front as illustrated.

NOTE: Do not operate if bafﬂe and manifold shield are not in position.

5.1 BRICKS AND BAFFLES INSTALLATION

WARNING

OPERATION OF THE APPLIANCE WITHOUT THE BAFFLES CAN RESULT IN EXCESSIVE

TEMPERATURES THAT COULD DAMAGE THE APPLIANCE, CHIMNEY AND THE SURROUNDING

ENCLOSURE.

1101 1402

(

Déﬂecteur en Fibre

)

W018-0078 X2

RETENUE

DU BRIQUE

NOTE: BRICKS

E & F ARE

NOTCHED AT

REAR.

(Fibre Bafﬂes)

W018-0078 X2

BRICK

RETAINERS

NOTE: BRIQUES

E & F SONT ENTAILLÉ

À L’ARRIÈRE

NOTE: BRICKS

E & F ARE

NOTCHED AT

REAR.

(Fibre Bafﬂes)

W018-0077 X2

BRICK

RETAINERS

RETENUE

DU BRIQUE

NOTE:

BRIQUES E & F

SONT ENTAILLÉ

À ARRIÈRE

(Déﬂecteurs

en Fibre)

W018-0077 X2

FIREBRICK

DIMENSIONS

PART #

FIREBRICK

DIMENSIONS

PART #

1101 1402 1101 1402

4 1/2” x 9”

(114mm x 229mm)

W090-0001

X15

W090-0001

X21

4 1/2” x 9”

(Notched)

(114mm x 229mm)

W090-0208

3” x 9” (Molded)

(6mm x 229mm)

W090-0002

2 1/4” x 9”

(57mm x 229mm)

W090-0018

4 1/2” x 4 1/2”

(114mm x 144mm)

W090-0003

N/A

2 1/4” x 6 1/8”

(64mm x 121mm)

W090-0019

3” x 9”

(76mm x 229mm)

W090-0166

2 1/2” x 4 1/2”

(64mm x 114mm)

W090-0016

4 1/2” x 9”

(Notched)

(114mm x 229mm)

W090-0207

1 1/2” x 4 1/2”

(38mm x 114mm)

W090-0017

All Firebricks are 1 1/4” (32mm) Thick

W415-1469 / C / 08.20.18

5.2 DOOR REMOVAL / INSTALLATION

Hang the door using the hinge pins supplied.

Twist the large wire handle over the end of the handle rod. Twist the smaller wire handle over the end of the air damper rod

below the door.

1402

ILLUSTRATED

5.3 DOOR HANDLE INSTALLATION

WARNING

BURNING YOUR APPLIANCE WITH THE DOORS OPEN OR AJAR CREATES A FIREE HAZARD THAT

MAY RESULT IN A HOUSE AND/OR CHIMNEY FIRE.

DO NOT STRIKE OR SLAM DOOR.

NEVER REMOVE THE DOOR WHEN THE APPLIANCE IS HOT.

DOOR

HANDLE

DOOR HANDLE

LATCH

LOCK

NUT

DOOR

SPACER

FRONT VIEW

NOTE: Position of

door handle latch.

98.1

NOTE: DOOR MAY NOT BE AS

ILLUSTRATED

SPRING

WASHER

W415-1469 / C / 08.20.18

5.4 FLASHING INSTALLATION

The top ﬂashing has been shipped ﬂat. To install the ﬂashing, rest the bottom against the top of the appliance and

secure using the tabs as illustrated below.

Slide the trim over the ﬂashing.

1402 illustrated. For 1101 ﬂashing instructions, please refer to the leaﬂet provided within the ﬂashing kit.

W415-1469 / C / 08.20.18

6.0 OPERATION

Your Napoleon EPA listed product is designed with the most advanced technology. The appliance is extremely

airtight. It has an exclusive direct outside air supply (optional kit), a safety feature designed to prevent spillage, and

to keep your house free of carbon monoxide, in case of a down drafting chimney or an internal negative pressure.

The ﬁrst ﬁre(s) in your appliance will be difﬁcult to get going and keep going with little amount of heat being

generated. This is a result of the moisture being driven out of the ﬁre brick. During the break-in period (the ﬁrst 2 or

3 ﬁres) create only small, ﬁres using kindling; this will allow the ﬁrebrick to cure. Do not be alarmed if small hairline

cracks develop in the ﬁrebrick. This is a normal occurrence and does not pose a safety hazard. The paint may also

smell a little for the ﬁrst few ﬁres as it cures and you may wish to open a door or window to alleviate the smell.

To start, a brisk ﬁre is required. Place loosely crumpled paper on the ﬂoor of the appliance and cover with dry

kindling. Open the draft control fully by pulling the lever forward. Light the paper and leave the door slightly ajar

(one inch) until all kindling is burning. To maintain a brisk ﬁre, a hot coal bed must be established and maintained.

Slowly add larger wood (2x4 size pieces). Lay the pieces lengthwise from side to side in the hot coal bed with a

shallow trench between, so that the primary air can ﬂow directly into this trench and ignite the fuel above. When

the ﬁre seems to be at its peak, medium sized logs may be added. Once these logs have caught ﬁre, carefully

close the door. (Closing the door too quickly after refuelling will reduce the ﬁrebox temperature and result in an

unsatisfactory burn.) Remember it is more efﬁcient to burn medium sized wood, briskly, and refuel frequently than

to load the appliance with large logs that result in a smouldering, inefﬁcient ﬁre and dirty glass.

As soon as the door is closed, you will observe a change in the ﬂame pattern. The ﬂames will get smaller and

lazier because less oxygen is getting into the combustion chamber. The ﬂames, however, are more efﬁcient. The

ﬂames will remain lazy but become larger again as soon as the ﬁrebricks have been heated thoroughly and the

chimney becomes heated and provides a good draft. At this point, the roaring ﬁre that you see when the door is

opened is wastefully drawing heated room air up the chimney -- certainly not desirable. Always operate with the

door fully closed once the medium sized logs have caught ﬁre.

WARNING

ALWAYS OPERATE THIS APPLIANCE WITH THE DOOR CLOSED AND LATCHED EXCEPT DURING

START UP AND RE-FUELING. ALWAYS WEAR GLOVES TO PREVENT INJURY. DO NOT LEAVE THE

FIRE UNATTENDED WHEN THE DOOR IS UNLATCHED AS UNSTABLE WOOD COULD FALL OUT OF

THE FIRE CHAMBER CREATING A FIRE HAZARD TO YOUR HOME.

NEVER LEAVE CHILDREN UNATTENDED WHEN THERE IS A FIRE BURNING IN THE APPLIANCE.

NEVER USE GASOLINE, GASOLINE-TYPE LANTERN FUEL, KEROSENE, CHARCOAL LIGHTER FLUID,

OR SIMILAR LIQUIDS TO START OR ‘FRESHEN UP’ A FIRE IN THIS APPLIANCE. KEEP ALL SUCH

LIQUIDS WELL AWAY FROM THE APPLIANCE WHILE IT IS IN USE.

OBJECTS PLACED IN FRONT OF THE APPLIANCE SHOULD BE KEPT A MINIMUM OF 48”

FROM THE FRONT FACE.

ANY MODIFICATION OF THE APPLIANCE THAT HAS NOT BEEN APPROVED IN WRITING BY THE

TESTING AUTHORITY IS CONSIDERED BREACHING CSA B365 (CANADA) AND ANSI NFPA 211 (USA).

OPEN AIR CONTROL (AND DAMPER WHEN FITTED) BEFORE OPENING FIRING DOOR.

HOT WHILE IN OPERATION, KEEP CHILDREN, CLOTHING AND FURNITURE AWAY. CONTACT MAY

CAUSE SKIN BURNS. WEAR GLOVES TO OPERATE YOUR APPLIANCE.

BURNING YOUR APPLIANCE WITH THE DOORS OPEN OR AJAR CREATES A FIRE HAZARD

THAT MAY RESULT IN A HOUSE AND OR CHIMNEY FIRE.

THIS WOOD APPLIANCE HAS A MANUFACTURER-SET MINIMUM LOW BURN RATE THAT MUST

NOT BE ALTERED. IT IS AGAINST FEDERAL REGULATIONS IN THE UNITED STATES TO ALTER THIS

SETTING OR OTHERWISE OPERATE THIS WOOD APPLIANCE IN A MANNER INCONSISTENT WITH

OPERATING INSTRUCTIONS IN THIS MANUAL.

W415-1469 / C / 08.20.18

You can now add larger pieces of wood and operate the appliance normally. Once the appliance is entirely hot,

it will burn very efﬁciently with little smoke from the chimney. There will be a bed of orange coals in the ﬁrebox

and secondary ﬂames ﬂickering just below the top ﬁrebrick. You can safely ﬁll the ﬁrebox with wood to the top of

the door and will get best burns if you keep the appliance pipe temperatures between 250°F (120°C ) and 450°F

(270°C ). A surface thermometer placed on the front top will help regulate this.

Without an appliance thermometer, you are working blindly and have no idea of how the appliance is operating! An

appliance thermometer offers a guide to performance.

Can’t get the ﬁre going?

Use more kindling and paper. Assuming the chimney and vent are sized correctly and there is sufﬁcient

combustion air, the lack of sufﬁciently dry quantities of small kindling is the problem. Thumb size is a good gauge

for small kindling diameter.

Can’t get heat out of the appliance?

One of two things may have happened. The appliance door may have been closed prematurely and the appliance

itself has not reached optimum temperature. Reopen the door and/or draft control to re-establish a brisk ﬁre. The

other problem may have been wet wood. The typical symptom is sizzling wood and moisture being driven from

the wood.

For optimal emissions performance and efﬁciency follow these simple guidelines when using your appliance:

A. Maintain a 2" (51mm) deep, hot, glowing red coal bed.

B. Burn dry seasoned wood with less than 20% moisture content and burn so that the glass door remains

clean.

C. A stove thermometer should indicate 350°F (176°C) as an average temperature.

D. Maintain a minimal trace of smoke coming from the chimney when the appliance is burning as intended.

E. Inspect and replace all necessary components such as gaskets, manifolds, glass and other components

which may affect the overall appliance performance.

F. Ensure an adequate draft to control burn rate and temperature.

Refer to “OPERATION” and “MAINTENANCE” sections for detailed information.

6.1 OPTIMUM BURN METHOD

W415-1469 / C / 08.20.18

THIS WOOD APPLIANCE HAS A MANUFACTURER-SET MINIMUM LOW BURN RATE THAT MUST

NOT BE ALTERED. IT IS AGAINST FEDERAL REGULATIONS IN THE UNITED STATES TO ALTER THIS

SETTING OR OTHERWISE OPERATE THIS WOOD APPLIANCE IN A MANNER INCONSISTENT WITH

OPERATING INSTRUCTIONS IN THIS MANUAL.

Draft is the force which moves air from the ﬁrebox up through the

chimney. The amount of draft in your chimney depends on the length

and diameter of chimney, local geography, nearby obstructions and

other factors including the amount of heat generated by the ﬁre

which can be measured by an appliance thermometer.

Adjusting the air control regulates the temperature. The draft can be

adjusted from a low burn rate with the handle in fully, to a fast burn

rate with the handle fully out.

Inadequate draft may cause back-pufﬁng into the room through the

appliance and chimney connector points and may cause plugging of

the chimney. Too much draft may cause an excessive temperature in the appliance, glowing red appliance parts

or chimney connectors or an uncontrollable burn which can lead to a chimney ﬁre or permanent damage to the

appliance.

Do not operate your appliance for longer than 30 minutes with the draft control on “HIGH” (fully open).

ASH LIP

91.1A

All homes with a solid fuel burning appliance should have at least one ﬁ re extinguisher in a central location,

known to all and at least one smoke detector and carbon monoxide (CO) detector in the room containing the

appliance. If the smoke detector sounds an alarm, correct the cause but do not de-activate or relocate the

smoke detector. If the carbon monoxide detector sounds an alarm, immediately vent the area, evacuate and

call your local ﬁ re department.

NOTE: Always check your smoke and CO detectors are working properly.

WARNING

Drywall dust will penetrate into the blower bearings, causing irreparable damage. Care must be taken to prevent

drywall dust from coming into contact with the blower or its compartment. Any damage resulting from this

condition is not covered by the warranty policy. Use of the blower increases the output of heat.

The 1402 inserts comes equipped with two blowers, while the 1101 has one blower. These blowers are thermally

activated and will not operate until the thermal switch reaches temperature (approximately 15-30 minutes

depending on the intensity of the ﬁre). The thermal switch for the 1402 is located on the right hand side of the unit

and the 1101 has a thermal switch located at the back on the blower access door. When ﬁrst starting the ﬁre,

the switch may be impeded by a large log or an unevenly burning ﬁre, causing the blowers to cycle on and off. To

control this, either build your ﬁre up evenly or turn down the blowers until the right side of the ﬁrebox is hot.

RISK OF FIRE AND ELECTRICAL SHOCK.

TURN OFF THE ELECTRICAL POWER BEFORE SERVICING THIS APPLIANCE.

USE ONLY WOLF STEEL APPROVED OPTIONAL ACCESSORIES AND REPLACEMENT PARTS WITH

THIS APPLIANCE. USING NON-LISTED ACCESSORIES (BLOWERS, DOORS, LOUVRES, TRIMS, ETC.)

COULD RESULT IN A SAFETY HAZARD AND WILL VOID THE WARRANTY AND CERTIFICATION.

ENSURE THAT THE BLOWER’S POWER CORD IS NOT IN CONTACT WITH ANY SURFACE OF THE

APPLIANCE TO PREVENT ELECTRICAL SHOCK OR FIRE DAMAGE. DO NOT RUN THE POWER

CORD BENEATH THE APPLIANCE.

6.2 BLOWER

6.3 AIR CONTROL

6.4 FIRE EXTINGUISHERS / SMOKE & CARBON MONOXIDE DETECTORS

W415-1469 / C / 08.20.18

6.5 FUEL

87.1E

When loading the appliance, ensure that the upper ﬁ bre bafﬂ e is situated properly. For maximum efﬁ ciency, when the appliance

is thoroughly hot, load it fully to the top of the door opening and burn at a medium low setting. The whiteness of the bricks

and the cleanliness of the glass are good indicators of your operating efﬁ ciency. Not enough heat is produced when only a few

pieces of wood are burned and/or the wood may not burn completely.

NOTE: When loading the appliance, ensure to keep fuel back from the glass. If coals are to accumulate on the front lip,

there is a chance they will fall out when the door is opened.

TYPES OF WOOD

Both hardwood and softwood burn equally well in this appliance but hardwood is denser, will weigh more per cord and burn a

little slower and longer.

Manufactured ﬁ relogs made by compressing 100% natural wood ﬁ bre can be safely used as fuel. Do not use manufactured

ﬁ relogs if they contain additives such as parafﬁ n, wax, binders etc. Never burn more than two manufactured ﬁ relogs at a

time.

MOISTURE CONTENT

Burn only dry, clean unpainted wood that has been seasoned. It produces more heat and less soot or creosote. Freshly cut

wood contains about 50% moisture while after proper seasoning only about 20% of the water remains. As wood is burned,

this water boils off consuming energy that should be used in heating. The wetter the wood, the less heat is given off and the

more creosote is produced. Dry ﬁ rewood has cracks in the end of the grain.

STORING WOOD

Firewood should be split and stacked in a manner

that allows for full air circulation and covered in early

spring to be ready for burning that fall. Dry ﬁ rewood

has cracks in the end grain.

Cut the wood so that it will ﬁ t horizontally, front

to back, making for easier loading and less of a

likelihood that the wood will roll onto the glass.

Fuel for the appliance must not be stored closer

than the required clearances to combustibles (heat

sensitive material). NEVER STORE WOOD IN THE

ASH PAN COMPARTMENT (if applicable).

WARNING

THIS APPLIANCE IS DESIGNED TO BURN NATURAL WOOD ONLY. DO NOT BURN TREATED

WOOD, COAL, CHARCOAL, COLOURED PAPER, CARDBOARD, SOLVENTS OR GARBAGE. THIS

APPLIANCE HAS NOT BEEN TESTED WITH AN UNVENTED GAS LOG SET. TO REDUCE RISK OF FIRE OR INJURY, DO NOT

INSTALL AN UNVENTED GAS LOG SET INTO THE APPLIANCE.

HIGHER EFFICIENCIES AND LOWER EMISSIONS GENERALLY RESULT WHEN BURNING AIR DRIED SEASONED HARDWOODS,

AS COMPARED TO SOFTWOODS OR TOO GREEN OR FRESHLY CUT HARDWOODS.

BURNING WET UNSEASONED WOOD CAN CAUSE EXCESSIVE CREOSOTE ACCUMULATION. WHEN IGNITED IT CAN CAUSE A

CHIMNEY FIRE THAT MAY RESULT IN A SERIOUS HOUSE FIRE.

DO NOT STORE FUEL WITHIN THE CLEARANCE TO COMBUSTIBLES, OR IN THE SPACE REQUIRED FOR RE-FUELING AND

ASH REMOVAL.

W415-1469 / C / 08.20.18

93.1

A ﬂ ash ﬁ re is a small ﬁ re burned quickly when you don't need much

heat. After your kindling has "caught", load at least 3 pieces of wood,

stacked loosely. Burn with the draft control fully open or closed only

slightly.

82.1

Load your larger pieces of wood so they are tightly packed, close enough to prevent the ﬂ ames from

penetrating it completely. After approximately 30 minutes, depending on the size of the load, close the draft

control completely making sure that the ﬁ re is not extinguished.

DO NOT OVERFIRE THE

APPLIANCE!

Overﬁ ring can occur by:

Burning large amounts of smaller wood pieces such as furniture scraps, skids or treated wood;

B. Vigorously burning large loads of wood with the draft control on “HIGH” (fully open) for long periods of

time (one or two hours).

Operating the appliance with the ash dump door blocked open or a poor gasket seal on the main door.

• Has a direct ﬂue connection been used rather than a chimney liner continuous from cap to appliance ﬂue

collar?

83.1A

A properly installed appliance should not smoke. If yours does, check the following:

•

Has the chimney had time to get hot?

•

Is the smoke passage blocked anywhere in the appliance, chimney connector or chimney?

•

Is the room too airtight and the air intake not connected to the outside? Try with a window partly open.

•

Is the smoke ﬂ ow impeded by too long a horizontal pipe or too many bends?

• Is it a weak draft perhaps caused by a leaky chimney, a cold outside chimney, too large a diameter of a

chimney, too short a chimney, or a chimney too close to trees or a higher roof?

•

Is the moisture content of the wood greater than 20%?

• If equipped, has the catalyst bypass been closed or closed prematurely?

6.6 LIGHTING A FIRE

6.6.1 FLASH FIRE

6.6.2 EXTENDED FIRE

6.7 SMOKING

La page charge ...

NAPOLEON EPI-1101M Manuel utilisateur

Marque: NAPOLEON

Modèle: EPI-1101M

Catégorie: Poêles

Taper: Manuel utilisateur

Ce manuel convient également à

EPI-1402M

Télécharger le PDF

rapport

dans d''autres langues

English: NAPOLEON EPI-1101M User manual

NAPOLEON EPI-1101M Manuel utilisateur

Ce manuel convient également à

NAPOLEON EPI-1101M Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents