Mi-T-M Air Compressor-Generator Combination Le manuel du propriétaire

Taper
Le manuel du propriétaire
Operator’s Manual 1
AIR COMPRESSOR/GENERATOR
OPERATOR’S MANUAL
CAUTION
RISK OF INJURY! READ ENTIRE MANUAL BEFORE OPERATING!
THIS MANUAL IS AN IMPORTANT PART OF THE AIR COMPRESSOR/GENERATOR
AND MUST REMAIN WITH THIS UNIT!
©Copyright 2005, Mi-T-M Corporation® 37-0945-E/F/S-080618
2 Operator’s Manual
Introduction
THANK YOU for purchasing a Mi-T-M product.
READ THIS MANUAL carefully to learn how to operate
and service your machine correctly. Failure to do so could
result in personal injury or equipment damage. This manual
and safety signs on your machine may also be available
in other languages. (See your dealer to order.)
THIS MANUAL SHOULD BE CONSIDERED a permanent
part of your machine and should remain with the machine
when you sell it.
MEASUREMENTS in this manual are given in both
metric and customary U.S. unit equivalents. Use only
correct replacement parts and fasteners. Metric and inch
fasteners may require a specic metric or inch wrench.
RIGHT HAND AND LEFT HAND sides are determined by
facing the motor end of the machine.
The SERIAL NUMBER is located in the Specication or
Identication Numbers section. Accurately record all the
numbers to help in tracing the machine should it be stolen.
Your dealer also needs these numbers when you order
parts. File the identication numbers in a secure place
off the machine.
WARRANTY is provided from your dealer for customers
who operate and maintain their equipment as described
in this manual. The warranty is explained on the warranty
certicate shown in this manual.
This warranty provides you the assurance that your
dealer will back products where defects appear within
the warranty period. Should the equipment be abused,
or modied to change its performance beyond the original
factory specications, the warranty will become void.
WARNING: This product can expose you to
chemicals including carbon monoxide, which is
known to the State of California to cause birth
defects or other reproductive harm. For more
information go to www.P65Warnings.ca.gov
WARNING
WARNING: This product can expose you to
chemicals including Lead, which is known to
the State of California to cause cancer and birth
defects or other reproductive harm. For more
information go to www.P65Warnings.ca.gov
WARNING
Operator’s Manual 3
Contents
Page
Safety ........................................................................ 5
Safety Signs ........................................................... 14
Controls ................................................................. 15
Installation .............................................................. 16
Operation ................................................................ 20
Troubleshooting ..................................................... 23
Maintenance ........................................................... 25
Storage .................................................................... 29
Specications ......................................................... 30
Warranty .................................................................. 31
All information, illustrations and specications in this manual are based
on the latest information available at the time of publication. The right is
reserved to make changes at any time without notice.
4 Operator’s Manual
Contents
Operator’s Manual 5
W
A
R
N
I
N
G
W
A
R
N
I
N
G
S
I
N
TH
E
M
A
N
U
A
L
S
.
W
A
R
N
I
N
G
S
I
N
TH
E
M
A
N
U
A
L
S
.
C
A
U
T
I
O
N
O
CAU
T
I
O
N
S
I
N
O
T
H
E
M
A
N
U
A
L
S
O
CAU
T
I
O
N
S
I
N
O
T
H
E
M
A
N
U
A
L
S
O
CAU
T
I
O
N
S
I
N
O
T
H
E
M
A
N
U
A
L
S
O
CAU
T
I
O
N
S
I
N
O
T
H
E
M
A
N
U
A
L
S
Safety
RECOGNIZE SAFETY INFORMATION
This is the safety alert symbol. When you see this symbol
on your machine or in this manual, be alert to the potential
for personal injury.
Follow recommended precautions and safe operating
practices.
UNDERSTAND SIGNAL WORDS
A signal word--DANGER, WARNING or CAUTION--is used
with the safety-alert symbol. DANGER identies the most
serious hazards.
DANGER or WARNING safety signs are located near
specific hazards. General precautions are listed on
CAUTION safety signs. CAUTION also calls attention to
safety messages in this manual.
FOLLOW SAFETY INSTRUCTIONS
Carefully read all safety messages in this manual and
safety signs on your machine. Keep safety signs in good
condition. Replace missing or damaged safety signs. Be
sure new equipment components and repair parts include
the current safety signs. Replacement safety signs are
available from your dealer.
Learn how to operate the machine and how to use controls
properly. Do not let anyone operate without instruction.
Keep your machine in proper working condition.
Unauthorized modications to the machine may impair the
function and/or safety and affect machine life.
If you do not understand any part of this manual and need
assistance, contact your dealer.
6 Operator’s Manual
CARBON MONOXIDE - POISONOUS GAS
Use unit outdoors, away from open windows, vents, or
doors.
Unit exhaust contains carbon monoxide - a poisonous gas that
can kill you. You CAN NOT smell or see this gas.
Never use the unit in enclosed or partially-enclosed spaces. The
unit can produce high levels of carbon monoxide very quickly. When
you use this unit, remember that you cannot smell or see carbon
monoxide. Even if you can’t smell exhaust fumes, you may still be
exposed to carbon monoxide.
If you start to feel sick, dizzy, or weak while using the unit, get to
fresh air RIGHT AWAY. DO NOT DELAY. The carbon monoxide from
the unit can rapidly lead to full incapacitation and death.
If you experience serious symptoms, get medical attention
immediately. Inform medical staff that carbon monoxide poisoning
is suspected. If you experienced symptoms while indoors, have
someone call the re department to determine when it is safe to
re-enter the building.
NEVER operate the unit in an explosive atmosphere, near
combustible materials or where ventilation is not sufcient to carry
away exhaust fumes. Exhaust fumes can cause serious injury
or death.
NEVER use the unit indoors, including in homes, garages,
basements, crawl spaces, and other enclosed or partially-enclosed
areas, even with ventilation. Opening doors and windows or using
fans will not prevent carbon monoxide build-up in the home.
Follow the instructions that come with your unit. Locate the unit
outdoors and away from doors, windows, and vents that could allow
the carbon monoxide gas to come indoors.
ONLY run unit outdoors and away from air intakes.
NEVER run unit inside homes, garages, sheds, or other semi-
enclosed spaces. These spaces can trap poisonous gases EVEN
IF you run a fan or open doors and windows.
If you start to feel sick, dizzy, or weak while using the unit, shut if
off and get fresh air RIGHT AWAY. See a doctor. You may have
carbon monoxide poisoning.
Install battery-operated carbon monoxide alarms or plug-in carbon
monoxide alarms with battery back-up in your home, according to
the manufacturer’s installation instructions. The carbon monoxide
alarms should be certied to the requirements of the latest safety
standards for carbon monoxide alarms. (UL 2034, IAS 6-96, or
CSA 6.19.01).
Test your carbon monoxide alarm frequently and replace dead
batteries.
Operator’s Manual 7
SAFETY WARNING WHEN REFUELING
Injury or death may occur as a result of improper fueling. Do not smoke
while lling engine fuel tank.
Always refuel slowly to avoid the possibility of spilled fuel which may
cause a risk of re.
Gasoline is extremely ammable and its vapors can explode if ignited.
Observe all safety regulations for the safe handling of fuel. Handle
fuel in safety containers. If the container does not have a spout, use a
funnel.
Do not overll the fuel tank, leave room for the fuel to expand.
Fill the tank only on an area of bare ground. While fueling the tank,
keep heat, sparks and open ame away. Carefully clean up any spilled
fuel before starting engine.
Always ll fuel tank in an area with plenty of ventilation to avoid
inhaling dangerous fumes.
NEVER store fuel for your unit in the home. Gasoline, propane, kerosene,
and other ammable liquids should be stored outside of living areas in
properly-labeled, non-glass safety containers. Do not store them near a
fuel-burning appliance, such as a natural gas water heater in a garage. If
the fuel is spilled or the container is not sealed properly, invisible vapors
from the fuel can travel along the ground and can be ignited by the
appliance’s pilot light or by arcs from electric switches in the appliance.
8 Operator’s Manual
ELECTRICAL HAZARDS
This product must be grounded. If it should malfunction or breakdown,
grounding provides a path of least resistance for electric current to
reduce the risk of electric shock.
DANGER - IMPROPER CONNECTION OF THE EQUIPMENT-
GROUNDING CONDUCTOR CAN RESULT IN A RISK OF
ELECTROCUTION. CHECK WITH A QUALIFIED
ELECTRICIAN OR SERVICE PERSON IF YOU ARE IN
DOUBT AS TO WHETHER THE UNIT IS PROPERLY
GROUNDED.
This unit is equipped with a grounding terminal for your protection.
Always complete the ground path from the unit to an external ground
source as instructed in the section labeled “Grounding Instructions” in
the Preparation section of this manual.
The unit is a potential source of electrical shock if not kept dry. Keep
the unit dry and do not use in rain or wet conditions. To protect from
moisture, operate it on a dry surface under an open, canopy-like
structure. Dry your hands if wet before touching the unit.
Plug appliances directly into the unit. Or, use a heavy duty, outdoor-
rated extension cord that is rated (in watts or amps) at least equal to
the sum of the connected appliance loads. Check that the entire cord
is free of cuts or tears and that the plug has all three prongs, especially
a grounding pin.
NEVER try to power the house wiring by plugging the unit into a
wall outlet, a practice known as “back feeding”. This is an extremely
dangerous practice that presents an electrocution risk to utility workers
and neighbors served by the same utility transformer. It also bypasses
some of the built-in household circuit protection devices.
If you must connect the unit to the house wiring to power appliances,
have a qualified electrician install the appropriate equipment in
accordance with local electrical codes. Or, check with your utility
company to see if it can install an appropriate power transfer switch.
For power outages, permanently installed stationary units are better
suited for providing backup power to the home. Even a properly
connected portable unit can become overloaded. This may result in
overheating or stressing the unit components, possibly leading to a
unit failure.
Operator’s Manual 9
RISK OF BURSTING
Serious injury or death may occur from an air tank explosion if air tanks
are not properly maintained. Drain air tank daily or after each use to
prevent moisture buildup in the air tank.
If air tank develops a leak, replace the air tank immediately. Never repair,
weld or make modications to the air tank or its attachments. Use only
genuine manufacturer repair parts for your unit. NEVER make adjustments
to the factory set pressures.
Serious injury may occur from the unit malfunction or exploding accessories
if incorrect system components, attachments or accessories are used.
Never exceed manufacturers maximum allowable pressure rating of
attachments.
Because of extreme heat, do not use plastic pipe or lead tin soldered
joints for a discharge line.
Never use the unit to inate small, low pressure objects such as toys.
RISK OF FIRE OR EXPLOSION
Serious injury or death may occur from normal sparks in the engine
ignition system or engine exhaust/mufer. Always operate the unit in a
well ventilated area free of ammable vapors, combustible dust, gases
or other combustible materials.
DO NOT SMOKE if spraying ammable material. Locate the unit at
least 20 feet away from the spray area. (An additional hose may be
required.)
Never ll the engine fuel tank while the engine is running or hot. Allow
the engine to cool two minutes before refueling. Do not refuel indoors or
in a poorly ventilated area.
Do not operate the unit if gasoline is spilled. Wipe the unit clean and
move it away from the spill. Avoid creating any ignition until the gasoline
has evaporated.
Do not store the unit near an open ame or any equipment such as a
stove, furnace, water heater, etc. which utilizes a pilot light or sparking
device.
A spark arrester must be added to the mufer of this engine if it is to be
used on any forest covered, brush covered or grass covered unimproved
land. The arrester must be maintained in effective working order by the
operator.
Serious injury may occur if any of the unit's ventilation openings are
restricted, causing the unit to overheat and start a re. Never place objects
against or on top of the unit. Operate the unit at least 12 inches away
from any wall or obstruction that would restrict proper ventilation.
10 Operator’s Manual
RISK OF BREATHING
Serious injury or death could occur from inhaling compressed air. The air
stream may contain carbon monoxide, toxic vapors or solid particles. Never
inhale air from the unit either directly or from a breathing device connected
to the unit.
Serious injury or death may occur from inhaling engine exhaust. This unit
was designed for outdoor use. Never operate this unit in an enclosed
area. Always make certain there is adequate ventilation (fresh outside air)
for breathing and combustion. This will prevent the buildup of dangerous
carbon monoxide gases. Beware of poorly ventilated areas, or areas with
inadequate exhaust fans.
Sprayed materials such as paint, solvents, paint remover, insecticides,
weed killers, etc. contain harmful vapors and poisons. Operate the unit
only in a well ventilated area. Follow all safety instructions provided with
the materials you are spraying. Use of a respirator may be required when
working with some materials.
RISK OF BURNS
Serious injury could occur from touching exposed metal parts. These areas
can remain hot for some time after the unit is shutdown. Never allow any
part of your body or other materials to make contact with any exposed metal
parts on the unit.
Never allow any part of your body to contact the engine mufer, compressor
head or adjacent areas.
Operator’s Manual 11
RISK OF FLYING OBJECTS
Soft tissue damage can occur from the compressed air stream. Always wear
safety glasses to shield the eyes from ying debris.
Never point the air stream at any part of your body, anyone else or
animals.
Never leave pressurized air in the unit. Shut off the unit and relieve pressure
when storing or attempting maintenance.
Serious injury can occur from loose debris being propelled at a high speed
from the compressed air stream. Always maintain a safe distance from
people and animals while operating the unit.
Do not move the unit while air tank is under pressure. Do not attempt to
move the unit by pulling on the hose.
RISK FROM MOVING PARTS
Risk of bodily injury from moving parts. Before performing maintenance,
always turn off the unit. Bleed pressure from the air hose and disconnect
spark plug wire (for gasoline engines), or remove the negative wire
from the battery post (for Diesel engines) to prevent engine from starting
unexpectedly. All repairs to the unit should be made by an Authorized
Service person.
Do not operate without protective covers/guards. Always turn off the unit
before removing any guard. Replace damaged covers/guards before using
the unit.
12 Operator’s Manual
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of injury, read this operator’s manual
completely before using. When using this product, the following
basic precautions should always be followed:
1. Risk from Negligence: Risk of injury from negligent use. Never
allow children or adolescents to operate this unit! Stay alert-
watch what you are doing. Do not operate the unit when fatigued
or under the inuence of alcohol or drugs. Know how to stop the
unit. Be thoroughly familiar with controls.
2. Risk of Unit Damage: Risk of major repair. Do not operate the
unit without an air lter. Do not operate the unit in a corrosive
environment. Always operate the unit in a stable, secure
position to prevent the unit from falling. Follow all maintenance
instructions listed in this manual.
3. When starting the unit, using recoil starter grip, be sure that
nothing is in a position to be hit by the operator’s hand or arm.
Be sure the switch on electric power tools is in the “OFF” position
before plugging them into the unit.
4. Do not operate the unit or any electrical tool in any area where
water or similar materials constitute an electrical hazard to the
operator. Do not operate on wet surfaces, in rain or in snow.
5. Always be sure that the unit is on secure footing so that it cannot
slide or shift around, endangering workers.
6. Avoid contacting the hot exhaust manifold, muffler or
cylinder(s).
7. Keep clear of all rotating parts.
8. Unless the tool or appliance is double insulated, it must be
grounded through a properly grounded receptacle. Tools and
appliances which have 3 prong plugs must be plugged into
extension cords and electrical receptacles with 3 holes. Before
operating any electrical item, be sure it is in good repair.
9. Beware of using this equipment in conned spaces. Conned
spaces, without sufcient fresh air ventilation, can contain
dangerous gases. Running gasoline engines in such environments
can lead to deadly explosions and/or asphyxiation.
10. Use extreme caution when lifting this unit. This unit is heavy
so proper lifting techniques should be used.
SAVE THESE INSTRUCTIONS
W
A
R
N
I
N
G
W
A
R
N
I
N
G
S
I
N
TH
E
M
A
N
U
A
L
S
.
W
A
R
N
I
N
G
S
I
N
TH
E
M
A
N
U
A
L
S
.
C
A
U
T
I
O
N
O
CAU
T
I
O
N
S
I
N
O
T
H
E
M
A
N
U
A
L
S
O
CAU
T
I
O
N
S
I
N
O
T
H
E
M
A
N
U
A
L
S
O
CAU
T
I
O
N
S
I
N
O
T
H
E
M
A
N
U
A
L
S
O
CAU
T
I
O
N
S
I
N
O
T
H
E
M
A
N
U
A
L
S
Operator’s Manual 13
WEAR PROTECTIVE CLOTHING
Wear close fitting clothing and safety equipment
appropriate to the job.
Wear a suitable hearing protective device such as
earmuffs or earplugs to protect against objectionable or
uncomfortable loud noises.
Operating equipment safely requires the full attention of
the operator. Do not wear radio or music headphones while
operating machine.
INSPECT UNIT
Be sure all covers, guards and shields are tight and in
place.
Locate all operating controls and safety labels.
Inspect power cord for damage before using. There is a
hazard of electrical shock from crushing, cutting or heat
damage.
PREPARE FOR EMERGENCIES
Keep a rst aid kit and re extinguisher handy.
Keep emergency numbers for doctors, ambulance service,
hospital and re department near your telephone.
Be prepared if a re starts.
SERVICE UNIT SAFELY
Before servicing the unit, disconnect all equipment and
battery (if equipped) and allow unit to cool down.
Service unit in a clean dry at area.
14 Operator’s Manual
SAFETY SIGNS
34-1284
Location: Baseplate
34-0826
Location: Beltguard
34-0599
Location: Engine
34-1616
Location: Generator
CAUTION/PRECAUCIÓN
Do not add fuel when
product is operating. Allow
engine to cool for two (2)
minutes before refueling.
34-0599/07262012
RISK OF FIRE
RIESGO DE FUEGE
No ponga combustible cuando el
producto este en operacion.
Permita que el motor se enfrie
por 2 minutos antes de
reablastecer de combustible.
WARNING/ADVERTENCIA
RISK OF BURNS
Muffler and adjacent
areas may exceed
150°F.
RIESGO DE QUEMAR
El amortiguador y las areas
adyacentes pueden Tener
temperaturas por arriba de 65°C.
34-0598/07262012
34-0598
Location: Engine
Beware of Hot Surfaces.
Allow unit to cool
before servicing.
RISK OF BURNS
RIESGO DE QUEMADURA
Tenga ud cuidado de los
superficies calientes. Permita
que la unidad se enfrie antes
de mantener.
34-1284/091012
WARNING/ADVERTENCIA
34-1616/091012
RISK OF ELECTRICAL SHOCK OR ELECTROCUTION! A generator is a
potential shock hazard which can result in serious injury or death.
• Generator must be kept dry.
• Do NOT operate unit with wet hands.
• Generator MUST be grounded before use. See operators manual for specific
instructions.
• Do not use around water or expose to rain. Store indoors.
RIESGO DE CALAMBRE ELECTRICO O ELECTROCUCION! Un generador es un potencial
riesgo de descarga que puede resultar en lesiones graves o muerte.
• Generadores tienen que mantener secos.
• No opere esta unidad con manos mojados.
• Generador TIENE que sea conectado a tierra antes de uso. Vea manual de operador para
instrcciones especificos.
• No use cerca aqua ni tenga la unidad en la lluvia. Débe almecenaria dentor.
WARNING / ADVERTENCIA
WARNING/ADVERTENCIA
34-0826/07262012
No opere la unidad sin todas
la cubierta correa en su sitio.
Do not operate unit
without beltguard
in place.
34-0826/07262012
No opere la unidad sin todas
la cubierta correa en su sitio.
Do not operate unit
without beltguard
in place.
RISK OF FIRE OR EXPLOSION!
• Do not spray flammable liquid in a confined area. Spray area must be well ventilated. Do not smoke
while spraying or spray where spark or flame is present. Keep compressors as far from spraying area as
possible.
• When a combustible liquid is sprayed there may be danger of fire or explosion, especially in a closed area.
• Arcing parts. Keep the unit at least 6m away from explosive vapors.
• Engine creates sparks. Do not operate in flammable environment. Follow all instructions and warnings
supplied with material to be sprayed.
• Do not smoke while filling engine fuel tank. Follow all fueling instructions in operator's manual.
• Air tanks may explode if not properly maintained. To prevent weakening of tanks caused by corrosion,
drain tanks after each use.
• This equipment incorporates parts, such as snap switches, receptacles, produce arcs or sparks and,
therefore, when located in a garage, it should be in a room or enclosure provided for the purpose, or
should be 18 inches (457mm) or more above the floor.
RISK OF ASPHYXIATION!
• Never use compressed air for breathing or respiration!
• Gasoline engines produce carbon monoxide; a poisonous, odorless gas which may cause death! Do not
start or operate compressor in an enclosed area. Area must be well ventilated.
RISK OF SEVERE INJURY!
• Before servicing gasoline unit, disconnect spark plug wire to prevent unit from starting unexpectedly.
• Wear safety glasses/face shields at all times.
• Never operate with beltguard removed. If guard becomes damaged, repair or replace before operating.
• Do not remove any air line or tank connections before relieving air pressure in the tank(s).
• Loose debris can be propelled at high speeds. Never direct air stream towards yourself or others.
RISK OF BURNS!
• Do not touch compressor head, discharge lines or engine components. Cool before servicing.
RISK OF DAMAGING COMPRESSOR AND CAUSING INJURY!
• Do not operate at pressure or speed in excess of manufacturer's recommendations.
• Do not operate with components rated less than the pressure marked on the nameplate.
Follow required maintenance procedures and intervals listed in the operator's manual. Service
should be performed only by qualified personnel. Compressor requires good ventilation to operate
properly. Use only factory replacement parts.
RIESGO DE INCENDIO O EXPLOSION!
• No rocie el líquido inflamable en una áred confinada la área para rociar tiene que ser bien ventilado. No fume cuando está
rociando ni vocie donde hay incendio o centella. Ponga los compresores lejos de la area de vociar si es posible.
• Cuando un liquido inflamable está rociado hay posible peligro de incendio o explosión, especialmente en un lugar cerrado.
• Partes de arco. Ponga la unidad menos de 6m lejos de los vapores explosívos.
• El motor se causan las centellas. No use en un lugar inflamable. Siga usted las instrucciones y advertencias con el
material para rociar.
• No fume cuando está llenando el tanque de combustible siga todas las instrucciones de combustible en el manual del
operador.
• Los tanques del aire puede explotar si no se mantenga bien. Para evitar la debilitación de los tanques del corrosión, drene
los tanques cada uso.
• Este equipo tiene los partes com interruptor de resortes, receptaculos, se producen o centellas y por eso, cuándo está en
un garaje, lebe estar en un cuarto o un encerramiento por este, o debe estar 18 pulgadas o (457 mm) o encima del suelo.
RIESGO DE LESIONES GRAVES!
• Antes de mantenerse la unidad gasolina, desconecte el hilo de la telegrafista para evitar la unidad a arrancar
inesperadamente.
RIESGO DE QUEMADURAS!
• No toque la cabeza del compresor, lineas del descargo o partes del motor. Permita que se enfrie antes del servicio.
RIESGO DE ASFIXIA!
• Nunca se use el aire del compresor para respirar o respiración!
• El motor produce carbón monóxido un vapor tóxico un olor que se puede causar morir. No use o arranca un lugar
encerrado. El área debe ser bien ventilado.
REISGO DE LESIONES!
• Lleve gafas de seguridad o blindaje todo el tiempo.
• Nunca opere sin cinturon de protección. Si el cinturon está dañado repare o reemplace antes de usarlo.
• Nunca saque cualquier linea del aire o conexione del tanque antes de eliminando del sion aire en los tanques.
• No dirija el rociado de alta presión hacia ninguna persona ni hacia usted mismo. Escombros se vuelan rapído.
RIESGO DE DAÑO DEL COMPRESOR O LESIONES!
• No opera a un presión o una velocidad más que se recomienda en el manual.
• No opera con partes clasifican menos de la presión que ha escrito en el plato de nombre.
Siga los procedimientos de mantenimiento y intervalos que se dicen en el manual de operador.
Servicio debe hacer solemento por las personas calificados. Para funcionar correctamente, necesita un lugar bien
ventilado. Use solamente partes para reemplacer de la fábrica.
READ ENTIRE INSTRUCTION MANUAL BEFORE OPERATING AIR COMPRESSOR!
LEA USTED EL MANUAL DE INSTRUCCIONES ANTES DE USAR EL COMPRESOR DEL AIRE!
SI NO SIGA USTED ESTAS ADVERTENCIAS PUEDE CAUSAR LESIONES.
NO SAQUE LA ETIQUETA!
FAILURE TO COMPLY WITH THESE WARNINGS WILL RESULT IN PERSONAL
INJURY. DO NOT REMOVE THIS LABEL!
34-1615/091012
WARNING ADVERTENCIA
34-1615
Location: Baseplate
WARNING: Cancer and Reproductive Harm — www.P65warnings.ca.gov/
1. Flip the toggle on top of the pilot valve to the upright position. This provides a loadless start.
The compressor will unload and allow the engine to start easier.
2. Start the engine. (Refer to Engine Manual accompanying this unit.)
3. When engine has run for 1-2 minutes, flip toggle back to original position.
4. Stop the engine. (Refer to Engine Manual accompany this unit.)
5. Drain air from the tanks by releasing air with an attached air tool or by pulling on the safety
relief valve rings.
6. Once pressure in the tanks register under 10 pounds, open the drain valve under each thank
to drain any moisture.
ADVERTENCIA: Peligro de cáncer y daño reproductivo — www.P65warnings.ca.gov/
1. Eche la palanca acodada encima de la válvula pilota a la posición vertical. Con este hay un arranque
sin carga. El compresor va a descargar y permitir el motor a arrancar facilmente.
2. Arranque el motor. (Lea el manual del motor que está acompañado está unidad)
3. Cuanda la unidad funciona para 1-2 minutos, mueva la planaca acodada a la posicion original.
4. Cierre el motor. (Lea el manual que está acompañado está unidad)
5. Drene los tanques del aire con un instrumento acompañado del aire o tire los anillos de la válvula
segura.
6. Cuando la presión en los tanques es menos de diez libras, abre la válvula debayo de cada tanque
para des aguar cualquier humedad.
34-1286/071318
34-1286
Location: Beltguard
LEA LAS INSTRUCCIONES PARA INSTRUCCIONES
PARTICULARES.
LEA USTED EL MANUAL DEL MOTOR PARA EL
MANTENIMIENTO RECOMENDADO DEL MOTOR.
Si la unidad está usado en un lugar bien sucio o de polvo, haga la frecuencia de
los examenes más.
Cada día: •Inspecciòne para el nivel de aceite y vias de aceite.
•Inspecciòne el filtro de aire (si hay).
•Drene la humidad de los tanques cada día o despúes de usar.
•Asegúrese que las guardas de seguridad son acompañados
seguridademente y correctamente.
Cada semana: •Limpie las superficies enfries del compresor.
•Inspeccióne el filtro del aire.
•Inspeccióne las válvulas con tirando los anillos.
Cada mes: •Inspeccióne la sistema para vías.
•Inspeccióne la tensión de la correa.
Cada dos •Cambie el aceite de la bomba.
cientos horas: •Reemplace filto del aire.
REFER TO INSTRUCTION MANUAL FOR
DETAILED INSTRUCTIONS.
REFER TO ENGINE MANUAL FOR RECOMMENDED
ENGINE MAINTENANCE.
If unit is operated in an excessively dirty or dusty area, increase
the frequency of all checks.
Daily: •Check for proper oil level(s) and oil leaks.
•Check engine air filter. (if applicable)
•Drain moisture from tank(s) daily or after each use.
•Ensure all safety guards are correctly & securely
attached.
Weekly: •Clean the cooling surfaces of the compressor.
•Inspect air intake filter.
•Check safety valves by pulling on rings.
Monthly: •Check system for air leaks.
•Check belt tension.
Every •Change pump oil.
200 hours: •Replace air filter.
34-1285/091012
MAINTENANCE INSTRUCTIONS INSTRUCCIONES DE MANTENIMIENTO
34-1285
Location: Baseplate
DANGER DANGER PELIGRO
34-1916/083012
Using a generator indoors CAN KILL YOU IN MINUTES.
Generator exhaust contains carbon monoxide. This is a
poison you cannot see or smell.
NEVER use inside a home
or garage, EVEN IF doors
and windows are open.
Only use OUTSIDE and far
away from windows, doors,
and vents.
Utilizando un generador adentro
PUEDE MATARLE EN MINUTOS.
El escape de generador contiene
monóxido de carbono. Este es un
gas tóxico que usted no puede ver ni
puede oler.
Nunca utilice dentro de un hogar ni el
garaje, INCLUSO SI puertas y
ventanas estén abiertas.
Solo utilice AFUERAS y lejos de
ventanas abiertas, las puertas, y
descargas.
L'utilisation d'un groupe électrogène à
l'intérieur PEUT VOUS TUER EN
QUELQUES MINUTES.
Le gaz d'échappement du groupe
électrogène contient de l'oxyde de
carbone. C'est un gaz toxique que l'on
ne peut pas voir ou sentir.
Ne JAMAIS utiliser à l'intérieur d'une
maison ou d'un garage, MÊME SI les
portes et fenêtres s'ont ouvertes.
N'utiliser qu'à l'EXTÉRIEUR et bien éloigné
des fenêtres, portes, et conduits d'aération.
34-1916
Operator’s Manual 15
CONTROLS (8 GALLON)
Controls
A -- Generator
B -- Pump
C -- Oil Sight Glass
D -- Handle
E -- Fuel Tank
F -- Engine
G -- Beltguard
H -- Tank Drain Valve
I -- Pressure Gauge
A
F
B
D
G
E
C
H
I
16 Operator’s Manual
CONTROLS (30 GALLON)
Controls
A -- Generator
B -- Pump
C -- Oil Sight Glass
D -- Handle
E -- Fuel Tank
F -- Engine
G -- Beltguard
H -- Tank Drain Valve
I -- Pressure Gauge
A
F
B
G
E
C
H
I
Operator’s Manual 17
INSTALLATION
Read safety warnings before setting-up the unit.
Ensure the oil level in the unit's pump is adequate. If low, add
SAE-30W non-detergent oil.
LOCATION:
In order to avoid damaging the unit, do not incline the unit transversely
or longitudinally more than 10°.
WARNING: RISK OF ASPHYXIATION! DO NOT
OPERATE IN AN ENCLOSED AREA. USE THIS
PRODUCT ONLY IN WELL VENTILATED AREAS!
THE EXHAUST FROM THE ENGINE CONTAINS
CARBON MONOXIDE, A POISONOUS, ODORLESS
AND INVISIBLE GAS. BREATHING THE GAS CAN
CAUSE SERIOUS INJURY, ILLNESS AND
POSSIBLE DEATH.
WARNING: RISK OF EXPLOSION OR FIRE
CAUSING SERIOUS INJURY OR DEATH! DO NOT
ALLOW THE ENGINE OR MUFFLER TO COME IN
CONTACT WITH FLAMMABLE VAPORS,
COMBUSTIBLE DUST, GASES OR OTHER
COMBUSTIBLE MATERIALS. A SPARK MAY
CAUSE A FIRE.
WHEN USING THE UNIT FOR SPRAY PAINTING,
PLACE THE UNIT AS FAR AWAY FROM THE WORK
AREA AS POSSIBLE, USING EXTRA AIR HOSES
IF NEEDED.
Place unit at least 12 inches away from obstacles that may prevent
proper ventilation. Do not place unit in an area:
- where there is evidence of oil or gas leaks.
- where ammable gas vapors or materials may be
present.
- where air temperatures fall below 32°F or exceed 104°F.
- where extremely dirty air or water could be drawn into the unit.
SERVICE TRUCK INSTALLATION:
Installations may vary. Mounting should be done to a rigid frame
member. Installer is responsible for securing the equipment in a
safe manner.
8 Gallon Units:
Recommended Hardware: 854-0093 (Dome Isolators)
30 Gallon Units:
Optional Hardware: 854-0093 (Dome Isolators)
Installation
Installation
18 Operator’s Manual
GROUNDING INSTRUCTIONS
This product must be grounded. If it should malfunction or breakdown,
grounding provides a path of least resistance for electric current to
reduce the risk of electric shock.
DANGER: IMPROPER CONNECTION OF THE EQUIPMENT -
GROUNDING CONDUCTOR CAN RESULT IN
A RISK OF ELECTROCUTION. CHECK WITH
A QUALIFIED ELECTRICIAN OR SERVICE PERSON
IF YOU ARE IN DOUBT AS TO WHETHER THE UNIT
IS PROPERLY GROUNDED.
The screw and ground terminal on the frame must always be used
to connect the unit to a suitable ground source. The ground path
should be made with #8 size wire. Connect the terminal of the
ground wire between the star washers and screw then tighten the
screw fully. Connect the other end of the wire securely to a suitable
ground source.
The National Electric Code contains several practical ways in which to
establish a good ground source. Examples given below illustrate a few
of the ways in which a good ground source may be established.
A metal underground water pipe in direct contact with the earth
for at least 10 feet can be used as a grounding source. If a pipe
is unavailable, an 8 foot length of pipe or rod may be used as the
ground source. The pipe should be 3/4 inch trade size or larger and
the outer surface must be noncorrosive. If a steel or iron rod is used
it should be at least 5/8 inch diameter and if a nonferrous rod is used
it should be at least 1/2 inch diameter and be listed as material for
grounding. Drive the rod or pipe to a depth of 8 feet. If a rock bottom
is encountered less than 4 feet down, bury the rod or pipe in a trench.
All electrical tools and appliances operated from this unit, must be
properly grounded by use of a third wire or be “Double Insulated”.
It is recommended to:
1. Use electrical devices with 3 prong power cords.
2. Use an extension cord with a 3 hole receptacle and a 3 prong
plug at the opposite ends to ensure continuity of the ground
protection from the unit to appliance.
Mi-T-M strongly recommend that all applicable federal, state and
local regulations relating to grounding specications be checked
and followed.
LINE TRANSFER SWITCH:
If this unit is used for standby service, it must have a transfer switch
between the utility power service and the unit. The transfer switch
not only prevents the utility power from feeding into the unit, but also
prevents the unit from feeding out into the utility company’s lines.
This is intended to protect the serviceman who may be working on
a damaged line.
THIS INSTALLATION MUST BE DONE BY A LICENSED
ELECTRICIAN AND ALL LOCAL CODES MUST BE
FOLLOWED.
Installation
Operator’s Manual 19
ENGINE
Review "Risk of Fire or Explosion" before fueling. Read the
engine manual accompanying this unit for correct engine start-up
maintenance procedures. Read and understand the safety labels
located on the unit.
WARNING: RISK OF EXPLOSION OR FIRE CAUSING
SERIOUS INJURY OR DEATH! DO NOT SMOKE
WHILE FUELING!
DO NOT FILL FUEL TANK WHILE THE UNIT IS
RUNNING OR HOT. ALLOW THE UNIT AND
ENGINE TO COOL DOWN FOR TWO MINUTES
BEFORE REFUELING.
DO NOT FILL FUEL TANK TO POINT OF
OVERFLOWING. ALLOW APPROXIMATELY
1/4" OF TANK SPACE FOR FUEL EXPANSION.
DO NOT PLACE UNIT IN AN AREA WHERE
FLAMMABLE GAS VAPORS MAY BE PRESENT.
A SPARK COULD CAUSE AN EXPLOSION OR
FIRE.
ALWAYS STORE FUEL AWAY FROM THE
UNIT WHILE IT IS RUNNING OR HOT.
WARNING: RISK OF EXPLOSION OR FIRE CAUSING
SERIOUS INJURY OR DEATH DO NOT ALLOW
THE ENGINE OR MUFFLER TO COME IN
CONTACT WITH FLAMMABLE VAPORS,
COMBUSTIBLE DUST, GASES OR OTHER
COMBUSTIBLE MATERIALS. A SPARK MAY
CAUSE A FIRE.
WHEN USING THE UNIT FOR SPRAY PAINTING,
PLACE THE UNIT AS FAR AWAY FROM THE
WORK AREA AS POSSIBLE, USING EXTRA AIR
HOSES IF NEEDED.
A minimum of 86 octane fuel is recommended for use with this air
compressor. Do not mix oil with gasoline.
Use of clean, fresh, lead free gasoline is recommended. Leaded
gasoline may be used if lead free is not available. Do not use
gasoline containing methanol or alcohol.
For Diesel units use low or ultra-low sulfer fuels only. Read engine
manual for recommended fuels.
Refer to the engine manual for all necessary maintenance and
adjustments.
Installation
20 Operator’s Manual
HIGH ALTITUDE
At high altitude, the standard carburetor air/fuel mixture will
be too rich. Performance will decrease, and fuel consumption
will increase. A very rich mixture will also foul the spark plug
on gasoline engines and cause hard starting. Operation at an
altitude that differs from that at which this engine was certied,
for extended periods of time, may increase emissions.
High altitude performance can be improved by specific
modications to the carburetor. If you always operate your
unit at altitudes above 5,000 feet (1,500 meters), have your
dealer perform this carburetor modication. This engine, when
operated at high altitude with the carburetor modications
for high altitude use, will meet each emission standard
throughout its useful life.
Even with carburetor modification, engine horsepower
will decrease about 3.5% for each 1,000-foot (300-meter)
increase in altitude. The effect of altitude on horsepower will
be greater than this if no carburetor modication is made.
NOTE: When the carburetor has been modied for high
altitude operation, the air/fuel mixture will be too lean
for low altitude use. Operation at altitudes below 5,000
feet (1,500 meters) with a modied carburetor may
cause the engine to overheat and result in serious
engine damage.
For use at low altitudes, have your servicing
dealer return the carburetor to original factory
specications.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92

Mi-T-M Air Compressor-Generator Combination Le manuel du propriétaire

Taper
Le manuel du propriétaire