TEAC DR-H338i Manuel utilisateur

Z

DR-H338i

DVD Receiver

OWNER’S MANUAL

MODE D’EMPLOI

MANUAL DEL USUARIO

ENGLISH FRANÇAIS

ESPAÑOL

41008765

2

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold with

the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to

avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused

for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way, such

as power-supply cord or plug is damaged, liquid has been spilled

or objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has

been dropped.

15) Grounding or Polarization – This product may be equipped with

a polarized alternating-current line plug (a plug having one blade

wider than the other). This plug will fit into the power outlet only

one way. This is a safety feature. If you are unable to insert the

plug fully into the outlet, try reversing the plug. If the plug should

still fail to fit, contact your electrician to replace your obsolete

outlet. Do not defeat the safety purpose of the polarized plug.

Alternate Warnings – This product is equipped with a three-wire

grounding-type plug, a plug having a third (grounding) pin. This

plug will only fit into a grounding-type power outlet. This is a

safety feature. If you are unable to insert the plug into the outlet,

contact your electrician to replace your obsolete outlet. Do not

defeat the safety purpose of the grounding-type plug.

16) Ventilation – Slots and openings in the cabinet are provided for

ventilation and to ensure reliable operation of the product and

to protect it from overheating, and these openings must not be

blocked or covered. The openings should never be blocked by

placing the product on a bed, sofa, rug, or other similar surface.

This product should not be placed in a built-in installation such

as a bookcase or rack unless proper ventilation is provided or the

manufacturer’s instructions have been adhered to.

17) The MAINS plug or an appliance coupler is used as the disconnect

device, the disconnect device shall remain readily operable.

18) Battery pack or battery installed shall not be exposed to excessive

heat such as sunshine, fire or the like.

19) Manufacture date is located on bottom of product.

20)

: CLASS II apparatus with double insulation, and no protective

earth provided.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the

literature accompanying the appliance.

IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with

the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are provided

for your safety. If the provided plug does not fit into your outlet,

consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

< Do not expose this apparatus to drips or splashes.

< Do not place any objects filled with liquids, such as vases, on the

apparatus.

< Do not install this apparatus in a confined space such as a book

case or similar unit.

< The apparatus draws nominal non-operating power from the

AC outlet with its POWER or STANDBY/ON switch not in the ON

position.

< The apparatus should be located close enough to the AC outlet so

that you can easily grasp the power cord plug at any time.

< The appliance coupler is used as the disconnect device,the

disconnect device shall remain readily operable.

CAUTION

< DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO EXPOSE

THE ELECTRONICS. NO USER SERVICEABLE PARTS ARE WITHIN.

< IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,

CONTACT TEAC FOR A SERVICE REFERRAL. DO NOT USE THE

PRODUCT UNTIL IT HAS BEEN REPAIRED.

< USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT

IN HAZARDOUS RADIATION EXPOSURE.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

3

ENGLISH

is a trademark of DVD Format/Logo Licensing Corporation.

This product incorporates copyright protection technology that is

protected by U.S. patents and other intellectual property rights.

Use of this copyright protection technology must be authorized by

Macrovision, and is intended for home and other limited viewing uses

only unless otherwise authorized by Macrovision. Reverse engineering

or disassembly is prohibited.

Manufactured under license from Dolby Laboratories. Dolby, Pro Logic

and the double-D symbol are trademarks of Dolby Laboratories.

HDMI, the HDMI logo and High-Definition Multimedia Interface are

trademarks or registered trademarks of HDMI Licensing LLC in the

United States and other countries.

DivX and the associated DivX logos are registered trademarks of DivX,

Inc.

MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS

and Thomson.

This product is licensed under the MPEG-4 Visual patent portfolio

license for the personal and non-commercial use of a consumer for

(i) encoding video in compliance with the MPEG-4 Visual Standard

("MPEG-4 Video") and/or (ii) decoding MPEG-4 Video that was

encoded by a consumer engaged in a personal and non-commercial

activity and/or was obtained from a video provider licensed by MPEG

LA to provide MPEG-4 Video. No license is granted or shall be implied

for any other use. Additional information including that relating to

promotional, internal and commercial uses and licensing may be

obtained from MPEG LA, LLC. See http://www.mpegla.com.

This product is protected by certain intellectual property rights of

Microsoft.

Use or distribution of such technology outside of this product is

prohibited without a license from Microsoft.

Windows Media is either a registered trademark or trademark of

Microsoft Corporation in the United States and/or other countries.

iPod is a trademark of Apple Inc., registered in the U.S. and other

countries.

“Made for iPod” means that an electronic accessory has been

designed to connect specifically to iPod and has been certified by the

developer to meet Apple performance standards.

Apple is not responsible for the operation of this device or its

compliance with safety and regulatory standards.

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the equipment and/or the receiving

antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

CAUTION

Changes or modifications to this equipment not expressly

approved by TEAC CORPORATION for compliance will void the

user’s warranty.

For U.S.A.

This product has been designed and manufactured according to

FDA regulations “title 21, CFR, chapter 1, subchapter J, based on the

Radiation Control for Health and Safety Act of 1968“, and is classified

as class 1 laser product. There is not hazardous invisible laser radiation

during operation because invisible laser radiation emitted inside of

this product is completely confined in the protective housings.

The label required in this regulation is as follows:

For U.S.A.

Bottom of the unit

Optical pickup

Type : KHS-313A

Manufacturer : Sony Electronics Inc.

Laser output : 7 mW (CD)

5 mW (DVD)

Wavelength : 655 +5, -10 nm / 790+10, -20 nm

< If the product uses batteries (including a battery pack or installed

batteries), they should not be exposed to sunshine, fire or excessive

heat.

< CAUTION for products that use replaceable lithium batteries: there

is danger of explosion if a battery is replaced with an incorrect type

of battery. Replace only with the same or equivalent type.

< Caution should be taken when using earphones or headphones

with the product because excessive sound pressure (volume) from

earphones or headphones can cause hearing loss.

4

Contents

Thank you for choosing TEAC. Read this manual carefully to get the best performance from this unit.

Before Use ....................................................5

Discs .........................................................6

USB memory device compatibility .............................8

Connecting Antennas (AM) ....................................8

Connecting Antennas (FM) ....................................9

Speaker Connection .........................................10

Connection to Audio Equipments etc. ........................11

Connection to a TV ..........................................12

Identifying the Parts (Main Unit) ..............................14

Identifying the Parts (Remote Control Unit) ...................16

Remote Control Unit .........................................18

Setting the Clock ............................................19

Basic Operation ..............................................20

Getting Started with an iPod .................................22

Listening to an iPod ..........................................23

Listening to a Disc ...........................................25

Listening to an USB Memory Device ..........................26

On-screen Menu .............................................26

Pausing Playback (Freezing a Picture) .........................28

Stopping Playback (Resume Mode) ...........................28

Skipping Playback ............................................29

Searching for a Part of a Chapter or Track .....................29

Selecting a Chapter or Track ..................................29

Selecting Audio ..............................................29

Selecting Subtitles ...........................................30

Changing Camera Angle .....................................30

Picture Zoom ................................................30

Slow Motion .................................................30

Repeat and Shuffle Playback .................................31

A-B Repeat Playback .........................................32

Changing the Display Mode ..................................32

Time Search (VCD/CD) .......................................33

Time Search (MP3/WMA) .....................................33

Chapter Search/Time Search (DVD) ...........................34

Chapter Search/Time Search (DivX) ...........................34

Programmed Playback (DVD, VCD, CD) ........................35

Programmed Playback (MP3, WMA, DIVX) .....................36

Settings (Introduction) .......................................37

Settings (GENERAL SETUP) ....................................38

Settings (AUDIO SETUP) ......................................39

Settings (VIDEO SETUP) ......................................40

Settings (PREFERENCE) .......................................41

Settings (PASSWORD SETUP) .................................42

Listening to the Radio (FM/AM) ...............................43

Preset Tuning (FM/AM) .......................................44

Listening to an External Source ...............................45

Sleep Timer ..................................................46

Wake Up Timer ..............................................46

Troubleshooting .............................................48

Specifications ................................................50

Conventions about this manual

< The types of functions and operations that can be used for a

particular disc vary depending on the features of that disc. In

some cases, these functions and operations may differ from

the descriptions given in this manual. In this event, follow the

instructions given on the screen. This manual only covers basic

disc operations.

< For some operations, the PROHIBIT icon “A” may appear on

the screen. This indicates that the operation described in this

manual is not permitted for the current disc.

5

ENGLISH

Before Use

What’s in the box

Confirm the supplied standard accessories.

AM antenna x 1

FM antenna x 1

Remote control unit (RC-1240) x 1

Batteries (AAA, R03, UM-4) for remote control unit x 2

AC power cord x 1

iPod dock x 1

Dock adapter x 2

RCA AV cable x 1

Owner’s manual (this document) x 1

< Keep this manual in a safe place for future reference.

Warranty card x 1

Beware of condensation

When the unit is moved from a cold to a warm place, or used after a

sudden temperature change, there is a danger of condensation; vapor

in the air could condense on the internal mechanism, making correct

operation impossible. To prevent this, or if this occurs, leave the unit

turned on for one or two hours. Then the unit will stabilize at the

temperature of its surroundings.

Placement of the unit

< Choose the installation location of your unit carefully. Avoid placing

it in direct sunlight or close to a source of heat. Also avoid locations

subject to vibrations and excessive dust, heat, cold or moisture.

< As the unit may become warm during operation, always leave

sufficient space around the unit for ventilation.

Make sure there is at least 8” (20 cm) of space above and at least 2”

(5 cm) of space on each side of the unit. Do not place anything on

top of the unit.

< Do not place the unit on an amplifier or receiver or any other

device that generates heat.

< When the unit is turned on, switching on the TV may cause lines

to appear on the TV screen, depending on the condition of the

electric waves of the TV broadcast. This is not malfunction in the

unit or the TV. If you see such lines, keep this unit well away from

the TV set.

CAUTION

< Do not move the unit during disc playback.

During playback, the disc rotates at high speed. Do not lift or

move the unit during playback. Doing so may damage the disc

or the unit.

< The voltage supplied to the unit should match the voltage as

printed on the rear panel. If you are in any doubt regarding this

matter, consult an electrician.

< Do not open the cabinet as this might result in damage to the

circuitry or electrical shock. If a foreign object should get into the

unit, contact your dealer or service company.

< When removing the power plug from the wall outlet, always pull

directly on the plug, never yank on the cord.

< To keep the laser pickup clean, do not touch it and always close

the disc tray.

< Always remove the disc before relocating or moving this unit.

Moving the unit with a disc inside it could cause malfunction.

Maintenance

If the surface of the unit gets dirty, wipe it with a soft cloth or

use diluted mild liquid soap. Allow the surface of the unit to dry

completely before using.

For safety, disconnect the power cord from the socket before

cleaning.

< Never spray liquid directly on this unit.

< Do not use thinner, benzene or alcohol as they could damage the

surface of the unit.

6

Type of discs that can be played on this unit

This player can playback discs bearing any of the following logos:

DVD Video

M Single-sided or double-sided discs

M Single layer or dual layer discs

M Dolby Digital, MPEG or Linear PCM digital audio

M MPEG-2 digital video

M This unit can play DVD-R discs recorded in DVD

video format.

M This unit can play DVD-RW discs recorded in

DVD video format or DVD video recording

format.

Discs are generally divided into one or more titles.

Titles may be further subdivided into chapters.

Audio CD

M 12cm or 8cm discs

M Linear PCM digital audio

Audio CDs are divided into tracks.

Video CD

M 12cm or 8cm discs

M MPEG-1 digital audio

M MPEG-1 digital video

Video CDs are divided into tracks.

SVCD

M 12 cm or 8 cm discs

M MPEG-1 Audio Layer2

M MPEG-2 digital video

Region Number of DVD Video discs

DVD players and discs are designed with region numbers that dictate

the regions in which a disc can be played. If the region number on

the disc you want to play does not match the region number of your

DVD player, you will not be able to play the disc. In that case, an error

message will appear on the screen.

The region number is printed on the rear panel of this unit.

U.S.A./Canada

model

Europe

model

Asia

model

About DVD-RW

< DVD-RW discs that were recorded with copy-once only permission

cannot be played.

< When playing a DVD-RW disc that was edited on a DVD recorder,

the screen may momentarily black out at the edited point.

< When playing a DVD-RW disc that was edited on a DVD recorder,

you may see scenes from just before the edited point.

About CD-R/CD-RW

CD-R/CD-RW discs recorded in Audio CD format and finalized

correctly are playable. But depending on the quality of the disc and/

or the condition of the recording, some CD-R/CD-RW discs may not

be playable.

CAUTION

< If you record a disc using a personal computer, even if it is recorded

in a compatible format, there are cases in which it may not play

because of the settings of the application software used to create

the disc. (Check with the software publisher for more detailed

information.)

< Unfinalized CD-R/CD-RW/DVD-R/RW discs cannot be played.

Discs cannot be played with this unit

< DVD-Audio, Super Audio CD, CD-G, Data part of CD-EXTRA, and

PHOTO CD discs

< discs recorded in a color system other than PAL or NTSC

< illegally produced discs

< scratched or damaged discs

< discs that are dusty, soiled or marked with fingerprints

CAUTION

If you attempt to play back such discs, there is a risk that sudden loud

noise can blast over the speakers at full volume and cause damage to

the speakers and your hearing.

Copy-protected discs, DualDiscs and other discs that do not conform

to the CD standard may not play back correctly in this player. If you

use such discs in this unit, TEAC Corporation and its subsidiaries

cannot be responsible for any consequences or guarantee the quality

of reproduction. If you experience problems with such non-standard

discs, you should contact the producers of the disc.

Discs

7

ENGLISH

Playable file format

This unit can play following files recorded on a CD-R, CD-RW, DVD-R,

DVD-RW or USB memory device:

M MP3 files

M Windows Media-formatted audio files

M JPEG files

M DivX video files

(DivX 5, DivX 4, DivX 3 and DivX VOD video content)

< File names should be alphanumeric characters. This unit cannot

display symbols and full-size or double-byte characters (such

as Japanese, Chinese, etc.) correctly. Also, be sure to use the file

extension. (‘.mp3’ for MP3 files, ‘.wma’ for WMA files, ‘.avi’ or ‘.divx’

for DivX video files, ‘.jpg or ‘.jpeg’ for JPEG files.)

< Files are played in alphabetical order.

< MP3 files must be monaural or stereo MPEG-1 Audio Layer 3

format. This unit can play MP3 files with sampling frequency

44.1 kHz or 48 kHz, bit-rate 320 kbps or less.

< This unit can play WMA files with sampling frequency 44.1 kHz, bit-

rate 192 kbps or less.

< This unit cannot display the bit-rate of VBR (variable bit rate) files

correctly.

< The disc must be finalized in order to play.

< This player is NOT compatible with multi-session discs.

< The CD-ROM must be ISO 9660 compatible.

< It may take time to display a progressive JPEG picture.

< Depending on the file size and compression rate, some JPEG

pictures cannot be displayed correctly.

Example of Icons used on DVD discs

Number of audio tracks recorded on the disc

Number of subtitles recorded on the disc

Screen aspect ratio

Disc recorded with multiple camera angles

Region code

CAUTION

< Do not play any disc that is warped, deformed or damaged. Playing

such discs may cause irreparable harm to the playing mechanisms.

< Printable discs are not recommended, as the label side might be

sticky and damage the unit.

< Do not stick papers or protective sheets on the discs and do not

use any protective coating spray.

< Never use a stabilizer. Using commercially available CD stabilizers

with this unit will damage the mechanisms and cause them to

malfunction.

< Do not use irregular shape discs (octagonal, heart shaped, business

card size, etc.). Discs of this sort can damage the unit:

Handling precautions

< Always place the disc on the disc tray with the label side up.

Compact discs can be played or recorded only on one side.

< To remove a disc from its storage case, press down on the center of

the case and lift the disc out, holding it carefully by the edges.

How to remove the disc How to hold the disc

Storage precautions

< Discs should be returned to their cases after use to avoid dust and

scratches that could cause the laser pickup to “skip.”

< Do not expose discs to direct sunlight or high humidity and

temperature for extended periods. Long exposure to high

temperatures will warp the disc.

< CD-R and CD-RW discs are more sensitive to the effects of heat

and ultraviolet rays than ordinary CDs. It is important that they are

not stored in a location where direct sunlight will fall on them, and

away from sources of heat such as radiators or heat-generating

electrical devices.

Maintenance

< Should the disc become dirty, wipe the surface radially (from the

center hole outward towards the outer edge) with a soft, dry cloth.

< Never use such chemicals as record sprays, antistatic sprays or

fluid, benzine or thinner to clean the discs. Such chemicals will do

irreparable damage to the disc’s plastic surface.

If you are in any doubt as to the care and handling of a disc, read the

precautions supplied with the disc, or contact the disc manufacturer.

8

Connecting Antennas (AM)

AM indoor loop antenna

The supplied high-performance AM loop antenna provided with

this unit is sufficient for good reception in most areas.

To stand the loop antenna on a surface, fix the claw to the slot in

the antenna base.

Connect the loop antenna‘s wires to the AM antenna terminals.

Press the lever, insert the end of the cord, then release the lever.

Make sure it is fastened securely by pulling the cord lightly. Make

sure only the bare, stripped wire is inserted in the jack and that no

plastic insulation is preventing contact between the antenna wire

and terminal.

Place the antenna on a shelf or hang it on a window frame, etc.,

in the direction which gives the best reception. Keep all other

wires such as power cords, speaker wires or interconnect wires as

far away as possible from the antenna.

< Only USB flash memory can be used. Do NOT use a high-capacity

USB hard disc with this unit.

< Some flash memory players that charge from an USB terminal

cannot be played back.

< Hard disk drives, CD/DVD drives, and other devices than flash

memory connected via USB cannot be used.

< The DR-H338i cannot copy, move, or delete files.

< Playable format: FAT12, FAT16, FAT32

< NTFS, HFS, HFS+ cannot be used.

< Max. number of playable folders: 300

< Max. number of playable files: 650

USB memory device compatibility

9

ENGLISH

AM outdoor antenna

If the AM loop antenna provided does not deliver sufficient

reception (often due to being too far from the transmitter or in a

concrete building, etc.), it may be necessary to use an outdoor AM

antenna.

Use either a high quality commercially available AM antenna or,

if not available, an insulated wire more than 16 ft (5 m) long, strip

one end, and connect this to the terminal as shown above.

The antenna wire should be strung outdoors or indoors near a

window. For better reception, connect the GND terminal to a

reliable ground.

< Even when using an outdoor AM antenna, do not disconnect the

AM loop antenna.

FM indoor antenna

Connect the supplied lead-type FM antenna to the FM 75Ω

socket and extend the lead.

Adjust the antenna in a suitable location like a window frame or

wall which gives the best reception and then fix the antenna in

that position with thumb tacks or the like.

FM outdoor antenna

In an area where FM signals are weak, it will be necessary to use a

75 Ω unbalanced-type outdoor FM antenna. Generally, a 3-element

antenna will be sufficient; if you live in an area where the FM signals

are particularly weak, it may be necessary to use one with 5 or more

elements.

< Disconnect the FM indoor antenna when using an FM outdoor

antenna.

Connecting Antennas (FM)

10

Speaker Connection

Before connection

Check the impedance of your speakers. Connect speaker with an

impedance of 4 Ω or more.

The black speaker terminals are “_” (negative).

Generally, the “+” side of the speaker cable is marked to make

it distinguishable from the “_” side of the cable. Connect this

marked side to the “+” terminal and the unmarked side to the

black “_” terminal.

Prepare the speaker cables for connection by stripping off

approximately 3/8” (10 mm) or less of the outer insulation.

Twist the strands of the stripped wires tightly together:

 CAUTION

The metal portions of the two separate wires should not touch or

an electrical short can occur. Removing too much insulation may

lead to a short circuit if the bared wired should come in contact

with each other. Shorted wires can create a fire hazard or induce a

failure in your equipment.

How to connect

1. Turn the terminal cap counterclockwise to loosen it. The speaker

terminal caps cannot be fully removed from the base.

2. Insert the wire into the terminal fully and turn the terminal cap

clockwise to securely connect it:

Make sure none of the wire insulation is under the terminal, only

the bare, stripped wire.

3. Make sure it is fastened firmly by pulling the cable lightly.

Subwoofer

Connect a subwoofer using a commercially-available RCA cable.

Use a subwoofer with built-in amplifier referred to as a “powered

subwoofer”.

Subwoofer

After all connections are complete, connect the power cord’s plug to the AC wall socket.

< Read the instructions of each component you intend to use with this unit.

< Be sure to connect each plug securely. To prevent hum and noise, do not bundle the connection cords.

11

ENGLISH

After all connections are complete, connect the power cord’s plug to the AC wall socket.

< Read the instructions of each component you intend to use with this unit.

< Be sure to connect each plug securely. To prevent hum and noise, do not bundle the connection cords.

A

Power cord receptacle

After all other connections have been made, insert the supplied

AC power cord into this receptacle, then connect the other

end of the power cord into the wall socket. Ensure that your AC

voltage corresponds to the voltage marked on the rear panel of

the unit. Consult a qualified electrician if you are in doubt.

In order to avoid the risk of electric shock, fire, and so on, only

use the supplied power cord.

< If you are not going to use the unit for some time, disconnect the

power cord from the wall socket.

B

AUX 1/LINE OUT jacks

Analog 2-channel audio signal is input or output from these

jacks. Connect a cassette tape deck etc. to these jacks using

commercially-available RCA cables.

Make sure to connect:

White plug

e White jack (L: left channel)

Red plug

e Red jack (R: right channel)

Connection to Audio Equipments etc.

C

D

B

A

RCA cable

Optical digital cable

Cassette tape deck etc.

Wall socket

Digital audio device

(CD recorder, MD deck, etc.)

C

iPod port

Connect the iPod dock to this port.

D

Digital audio output terminal

Digital audio from DVD-Video, CD and video CD is output from

this terminal.

Connect an amplifiers including a decoder, or digital audio

devices such as CD recorders, etc. to this jack using commercially-

available optical digital audio cable (TOS).

< Select “ALL” or “PCM only” in the DIGITAL AUDIO SETUP (page 39).

12

Connection to a TV

G

E

F

VIDEO

IN

TV (Monitor)

HDMI

IN

COMPONENT

VIDEO IN

C

BYCR

Connect one of

these cables.

Component video cable

RCA video cable

HDMI cable

13

ENGLISH

G

HDMI video/audio output terminal

Use a commercially available HDMI cable to connect the unit to a

HDMI compatible TV or monitor.

< If the TV or monitor is equipped only with a DVI terminal, a

suitable adaptor cable or adaptors should be used. Note that the

TV connected in this way must be HDCP compatible.

Also note that this connection outputs no sound.

< Make sure that you read and understand the documentation

provided with the HDMI component.

HDMI video output formats

< 480p (NTSC) or 576p (PAL)

< 720p

< 1080i

< 1080p

< See page 41 for further details on HDMI video output formats.

To output audio from the HDMI terminal

If the connected HDMI component is capable of inputting HDMI

audio, digital audio can be output from the HDMI terminal.

< Select “ALL” or “PCM only” in the DIGITAL AUDIO SETUP (page 39).

< To enjoy the digital surround audio from DVD-Video discs,

connect the HDMI terminal to a surround amplifier and set the

DIGITAL AUDIO SETUP to “ALL” (page 39).

< Adjust the video aspect ratio to match that of the TV (page 38).

< This unit adopts analog copy protection features. If the unit is

connected to a TV through a VCR (video cassette recorder), the

resulting playback may be affected. Connect the unit directly to

the TV.

< In all cases, use the highest quality cables for the best possible

picture.

< Select proper setting in the VIDEO OUTPUT setup (page 40).

E

Component video output terminals

Use commercially available component video cables to connect

the unit to the component video inputs of a suitably equipped

TV or monitor to enjoy a high-quality picture.

Use these terminals in preference to composite video

connections.

< If the component video terminals are connected to a TV with

progressive scan capabilities, the output can be set to match this

(page 40).

< Note that these terminals cannot be connected to high definition

component terminals.

F

Composite video output terminal

Use a commercially available RCA (pin) video cable to connect

the unit to the composite video connector of a TV or monitor.

Use this connection only if no other video connection method is

available.

14

Identifying the Parts (Main Unit)

A

P

N

DC

B

E

G

F

H

I

J

K

L

M

O

15

ENGLISH

A

SOURCE

Use this button to select a source.

B

Search (

m

/

,

)/PRESET

In FM or AM mode, use these buttons to select a preset channel.

In DISC, USB or iPod mode, use these buttons to search for a part

of a track/file/song.

C

Skip (

.

/

)/TUNING

In FM or AM mode, use these buttons to tune in a station.

In DISC, USB or iPod mode, use these buttons to skip tracks/files/

songs.

D

Play/Pause (

G

/

J

)/FM MODE

In FM mode, use this button to select stereo or monaural.

In DISC, USB or iPod mode, use this button to start or pause

playback.

E

Stop (

H

)/SCAN

In FM or AM mode, use this button to preset stations

automatically.

In DISC or USB mode, use this button to stop playback.

F

Open/Close (

L

)

Use this button to open and close the disc tray.

When the tray is opened during playback, it may take a few

seconds before the disc is “unloaded” and the tray opens.

G

VOLUME

Turn this knob to adjust the volume level.

H

PROGRAM/MEMORY

In FM or AM mode, use this button to preset stations.

In DISC or USB mode, use this button to programme tracks.

I

PHONES

To listen with headphones, first lower the volume level to the

minimum. Then, connect the headphones plug into the PHONES

jack, and adjust the volume by turning the VOLUME knob.

The speakers will make no sound when headphones are plugged

in.

CAUTION

Do not connect headphones with the PHONES jack while

wearing them. Moreover, do not disconnect headphones or turn

the unit on or off while wearing them. Very loud sound could be

output from the headphones.

AVOID DAMAGING YOUR HEARING

-

Do not put on headphones

until after plugging them in.

J

REPEAT

In DISC, USB or iPod mode, use this button for repeat playback.

K

AUX 2 IN

You can connect a portable audio player to this jack.

L

Remote control sensor

Receives signals from the remote control unit. Point the remote

control unit at this sensor when operating the remote control

unit.

M

USB connector

You can connect an USB memory device to this connector.

N

Display

O

Disc tray

P

STANDBY/ON

Use this button to turn the unit on and standby.

The indicator lights blue when the unit is turned on.

The indicator lights orange when the unit is in the standby mode.

16

Identifying the Parts (Remote Control Unit)

A

C

P

S

G

J

F

X

Y

D

B

I

E

K

M

L

N

O

H

Q

R

T

V

a

b

c

d

U

W

Z

A

STANDBY/ON

Use this button to turn the unit on and standby.

B

Number buttons

Use these buttons to enter track numbers, passwords, etc.

C

Source

Use these buttons to select a source.

D

SETUP

Use this button to enter the setup menu where you can set up

the parameters of the unit.

E

ANGLE

Use this button to select camera angles during DVD playback.

F

Search (

m

/

,

)/PRESET (+/–)

In FM or AM mode, use these buttons to select a preset channel.

In DISC, USB or iPod mode, use these buttons to search for a part

of a track/file/song.

G

REPEAT/INFO/RDS

In DISC, USB or iPod mode, use this button for repeat playback.

H

A-B (Repeat)

In DISC or USB mode, use this button to specify a section and

play it repeatedly.

I

DIMMER

Use this button to change the brightness of the front panel

display.

J

VOL (+/–) (Volume)

Use these buttons to adjust the volume level.

K

SLOW

In DISC mode, use this button for slow motion video playback.

L

ZOOM

In DISC or USB mode, use this button to enlarge the image.

17

ENGLISH

M

TONE

Use this button to adjust bass and treble together with the

VOLUME buttons.

N

DVS (Dolby Virtual Speaker)

In DISC or USB mode, use this button to select the listening

mode.

O

LOUDNESS

Use this button to compensate for the loss of bass at low

volumes.

P

Open/Close (

L

)

Use this button to open and close the disc tray.

When the tray is opened during playback, it may take a few

seconds before the disc is “unloaded” and the tray opens.

Q

SLEEP/TIMER

When the unit is on, use this button to set the sleep timer.

In the standby mode, use this button to set the wake up timer.

R

CLOCK

In the standby mode, use this button to adjust clock.

S

PROG/MEM (Program/Memory)

In FM or AM mode, use this button to preset stations.

In DISC or USB mode, use this button to programme tracks.

T

OSD (On Screen Displays)

Use this button to display information about the currently playing

disc.

U

TIME

Use this button to start time search.

V

SUBTITLE

Use this button to select the displayed subtitles during DVD

playback.

W

AUDIO

Use this button to select the audio for playback.

X

Skip (

.

/

)/TUNING (+/–)

In FM or AM mode, use these buttons to tune in a station.

In DISC, USB or iPod mode, use these buttons to skip tracks/files/

songs.

Y

Stop (

H

)/SCAN

In FM or AM mode, use this button to preset stations

automatically.

In DISC or USB mode, use this button to stop playback.

Z

Play/Pause (

G

/

J

)/SELECT/FM MODE

In FM mode, use this button to select stereo or monaural.

In DISC, USB or iPod mode, use this button to start or pause

playback.

a

MUTING

Use this button to mute the sound.

b

TITLE

During PBC playback, use this button to display a menu.

c

Cursor buttons (

5

/

b

/

t

/

g

) and Enter ( )

Use these Cursor buttons for navigation of on-screen menus and

the Enter button to confirm selections.

d

MENU

In DISC mode, use this button with menu-enabled DVD discs to

bring up the DVD menu.

During playback of MP3/WMA/JPEG files, use this button to

switch between the folder list and the file list.

In iPod mode, use this button to go back to previous menu of

iPod. This button is equivalent to the MENU button on your iPod.

When a video CD (version 2.0) is loaded, use this button to turn

the PBC function on or off.

Note:

To simplify explanations, instructions in this manual might refer to the

main unit or remote control only. In such cases, the same controls on

the remote control and main unit will operate similarly.

18

The provided Remote Control Unit allows the unit to be operated

from a distance.

When operating the remote control unit, point it towards the remote

sensor on the front panel of the unit.

< Even if the remote control unit is operated within the effective

range (16 ft/5 m), remote control operation may be impossible if

there are any obstacles between the unit and the remote control.

< If the remote control unit is operated near other products which

generate infrared rays, or if other remote control devices using

infrared rays are used near the unit, it may operate incorrectly.

Conversely, the other products may operate incorrectly.

Battery installation

1. Remove the battery compartment cover.

2. Insert two “AAA” (R03 or UM-4) dry batteries. Make sure that the

batteries are inserted with their positive “+” and negative “_”

poles positioned correctly.

3. Close the cover.

Remote Control Unit

Battery replacement

If the distance required between the remote control unit and main

unit decreases, the batteries are exhausted. In this case replace the

batteries with new ones.

For more information about collection of batteries, please contact

your local municipality, your waste disposal service or the point of sale

where you purchased the items.

Precautions concerning batteries

Misuse of batteries could cause them to rupture or leak leading to fire,

injury or the staining of nearby things. Please read and observe the

following precautions carefully.

< Be sure to insert the batteries with correct positive (+) and

negative (_) orientations.

< Use batteries of the same type. Never use different types of

batteries together.

< Both rechargeable and non-rechargeable batteries can be used.

Refer to the precautions on their labels.

< If the remote control will not be used for a long time (more than a

month), remove the batteries to prevent them from leaking.

< If the batteries leak, wipe away the leakage inside the battery

compartment and replace the batteries with new ones.

< Do not use batteries of types other than those specified. Do not

mix new batteries with old ones or use different types of batteries

together.

< Do not heat or disassemble batteries. Never throw batteries into

fire or water.

< Do not carry or store batteries with other metallic objects. The

batteries could short circuit, leak or explode.

< Never recharge a battery unless it is confirmed to be a

rechargeable type.

19

ENGLISH

Setting the Clock

When you connect the power cord into the wall socket and turn on

the unit for the first time, set the clock.

1

If the unit is on, press the STANDBY/ON button to turn it

standby.

2

Press the CLOCK button.

< If “- -:- -” blinks on the display, press the CLOCK button again.

“Clock Set” appears on the display, and the “hour” value starts

blinking.

< When no button is pressed for 30 seconds, the time setting

mode will be cancelled.

3

Press the Volume buttons (+ or –) to set the current hour.

4

Press the CLOCK button.

The “minute” value starts blinking.

5

Press the Volume buttons (+ or –) to set the current

minute.

6

Press the CLOCK button.

The clock starts.

After the clock is set, also set the settings of the unit using the

SETUP menu (page 37).

20

< You can also select FM or AM by pressing the TUNER button on

the remote control unit once or twice.

< You can also select iPod or USB by pressing the iPod/USB button

on the remote control unit once or twice.

< To listen to an external source connected to the AUX IN jack,

select AUX1 or AUX2.

< You can also select AUX1 or AUX2 by pressing the AUX button

on the remote control unit once or twice.

3

Play the source, and adjust the volume using the VOLUME

knob.

The volume is adjustable from MIN to MAX. You can hold down

the VOLUME – or + buttons on the remote control unit to reduce

or bring up the volume continuously.

< Press the STANDBY/ON button to put the unit in the standby

mode when it is not being used.

< If you press the STANDBY/ON button to put the unit in the

standby mode when SOURCE is set for AUX1 or AUX2, first, the

speaker sound stops and then after about 2 seconds the output

to the sub woofer stops.

This chapter describes the basic operation which is available in every

mode.

When you use the unit for the first time, set the clock and the setting

of the unit. (see previous page for “Setting the Clock”, page 37 for

“Settings”).

1

Press the STANDBY/ON button to turn the unit on.

< The unit turns on with the source that was last selected.

< You can also use the SOURCE button (or the TUNER, DISC, iPod/

USB or AUX button on the remote control unit) to turn the unit

on.

2

Press the SOURCE button to select a source.

Each time the SOURCE button is pressed, the source changes as

follows:

FM Radio

AM Radio

AUX1 Source

AUX2 Source

iPod

DISC Source

USB Source

The selected source is shown on the front panel’s display.

Basic Operation (1)

La page charge ...

TEAC DR-H338i Manuel utilisateur

Ce manuel convient également à

TEAC DR-H338i Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents