Seca 777 Manuel utilisateur

Marque: Seca

Modèle: 777

Taper: Manuel utilisateur

seca 777

Instructions for use and warranty . . . . . . . . . . . . . . . . . . . . 3

Mode d'emploi et garantie . . . . . . . . . . . . . . . . . . . . . . . . . 32

Instrucciones de uso y garantía . . . . . . . . . . . . . . . . . . . . 61

Contents • 3

English

17-10-07-651-100a/07-2019S

English

CONTENTS

1. Description of device . . . . . . . . . . . . . . . . . . . . . . . . 4

1.1 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.2 Description of function . . . . . . . . . . . . . . . . . . . . 4

Measuring station . . . . . . . . . . . . . . . . . . . . . . 4

USB interface . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.3 User qualification . . . . . . . . . . . . . . . . . . . . . . . . 4

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2. Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2.1 Safety precautions in these instructions for

use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2.2 Basic safety precautions . . . . . . . . . . . . . . . . . . . 5

Handling the device . . . . . . . . . . . . . . . . . . . . . 5

Preventing electric shock . . . . . . . . . . . . . . . . . 6

Preventing injuries and infections . . . . . . . . . . . 6

Preventing damage to device . . . . . . . . . . . . . . 7

Handling measuring results . . . . . . . . . . . . . . . 7

Handling packaging material . . . . . . . . . . . . . . 8

Handling batteries and rechargeable

batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.1 View of device . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.2 Display unit controls . . . . . . . . . . . . . . . . . . . . . 10

3.3 Symbols in the display . . . . . . . . . . . . . . . . . . . 11

3.4 Markings on the device and on the type

plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.5 Markings on the packaging . . . . . . . . . . . . . . . . 12

4. Starting up device . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.1 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . 13

4.2 Assembling the device . . . . . . . . . . . . . . . . . . . 13

Tools required . . . . . . . . . . . . . . . . . . . . . . . . 14

Fitting the measuring rod . . . . . . . . . . . . . . . . 14

Fitting the column . . . . . . . . . . . . . . . . . . . . . 15

Fitting the display head . . . . . . . . . . . . . . . . . 16

Switching the positions of the display unit

and the battery compartment . . . . . . . . . . . . 17

Setting up the device . . . . . . . . . . . . . . . . . . . 19

Disinfecting the device . . . . . . . . . . . . . . . . . . 19

4.3 Transporting the device . . . . . . . . . . . . . . . . . . 19

4.4 Establishing the power supply . . . . . . . . . . . . . . 20

Inserting batteries . . . . . . . . . . . . . . . . . . . . . 20

Connecting the plug-in power supply unit

(optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

5. Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

5.1 Switching the device on and off . . . . . . . . . . . . 21

Switching on the device . . . . . . . . . . . . . . . . . 21

Switching off the device . . . . . . . . . . . . . . . . . 21

5.2 Switching units of measurement (variant-

dependent) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

5.3 Measuring weight . . . . . . . . . . . . . . . . . . . . . . . 22

Weighing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Taring off additional weight (Tare) . . . . . . . . . . 22

Displaying weight permanently (Hold) . . . . . . . 23

5.4 Measuring height . . . . . . . . . . . . . . . . . . . . . . . 23

Measuring heights < 1.22 m . . . . . . . . . . . . . 23

Measuring heights > 1.22 m . . . . . . . . . . . . . 24

5.5 Calculating and displaying body mass index

(BMI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

6. Hygiene treatment . . . . . . . . . . . . . . . . . . . . . . . . . . 26

6.1 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

6.2 Disinfecting . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

6.3 Sterilizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

7. Function check . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

8. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

9. Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

10. Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

10.1 General technical data . . . . . . . . . . . . . . . . . . .29

10.2 Weighing data . . . . . . . . . . . . . . . . . . . . . . . . . 29

11. Optional accessories . . . . . . . . . . . . . . . . . . . . . . . 30

12. Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

12.1 Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

12.2 Batteries and rechargeable batteries . . . . . . . . 30

13. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

14. Declarations of conformity . . . . . . . . . . . . . . . . . . 31

14.1 For Europe . . . . . . . . . . . . . . . . . . . . . . . . . . .31

14.2 For USA and Canada . . . . . . . . . . . . . . . . . . . .31

4 •

17-10-07-651-100a/07-2019S

1. DESCRIPTION OF DEVICE

1.1 Intended use

The seca 777 measuring station is used in accordance with national regula-

tions primarily in hospitals, medical practices and in-patient care facilities.

The

seca 777 measuring station is for conventional determination of weight

and height and for determining the general state of nutrition; it supports the

attending physician in making a diagnosis or deciding on a course of treat-

ment.

To make an accurate diagnosis, however, the physician needs to commission

other specific examinations and take their results into account, in addition to

determining weight and height.

1.2 Description of function

Measuring station On the seca 777 measuring station, weight is recorded by four load cells.

Height is recorded with the integrated measuring rod.

Body mass index (BMI) can be calculated automatically from the measuring

results.

USB interface The USB interface allows the seca 777 measuring station to be connected to

a PC by means of a suitable USB cable (USB 2.0, mini USB type B, max.

cable length: 1.80 m). This makes it possible to process the weight values

displayed using the customer’s own software solution.

1.3 User qualification

Assembly Devices that are shipped partially assembled may only be mounted by suffi-

ciently qualified persons such as specialist dealers, hospital technicians or

seca Service technicians.

Operation The device may only be operated by healthcare professionals.

2. SAFETY INFORMATION

2.1 Safety precautions in these instructions for use

DANGER!

Used to identify an extremely hazardous situation. If you fail to take

note of this information, serious irreversible or fatal injuries will occur.

WARNING!

Used to identify an extremely hazardous situation. If you fail to take

note of this information, serious irreversible or fatal injuries may result.

CAUTION!

Used to identify a hazardous situation. If you fail to take note of this

information, minor to moderate injuries may result.

Safety information • 5

English

17-10-07-651-100a/07-2019S

NOTICE!

Used to identify possible incorrect usage of the device. If you fail to

take note of this information, you may damage the device, or the

measured results may be incorrect.

NOTE

Includes additional information about use of the device.

2.2 Basic safety precautions

Handling the device ► Please take note of the information in these instructions for use.

► Keep the instructions for use in a safe place. The instructions for use are a

component of the device and must be available at all times.

DANGER!

Risk of explosion

Do not use the device in an environment in which one of the following

gases has accumulated:

– oxygen

– flammable anesthetics

– other flammable substances/air mixtures

CAUTION!

Patient hazard, damage to device

► Additional devices which are connected to electrical medical

devices must provide evidence of compliance with the relevant IEC

or ISO standards (e.g. IEC 60950 for data-processing devices).

Furthermore, all configurations must comply with the requirements

of standards for medical systems (see IEC 60601-1-1 or Section 16

of edition 3.1 of IEC 60601-1 respectively). Anyone connecting

additional devices to electrical medical devices is considered a

system configurer and is therefore responsible for ensuring that the

system complies with the requirements of standards for systems.

This also applies to additional devices recommended by seca. Your

attention is drawn to the fact that local laws take precedence over

the above-mentioned requirements of standards. In the event of any

queries, please contact your local specialist dealer or Technical

Service.

► Have servicing carried out regularly as described in the relevant

section of this document.

► Technical modifications may not be made to the device. The device

does not contain any parts for servicing by the user. Only have

servicing and repairs performed by an authorized seca Service

partner. You can find service partners in your area at

www.seca.com or by sending an e-mail to [email protected].

► Only use original seca accessories and spare parts, otherwise seca

will not grant any warranty.

CAUTION!

Patient hazard, malfunction

► Keep other electrical medical devices, e.g. high-frequency surgical

devices, a minimum distance of approx. 1 meter away to prevent

incorrect measurements or wireless transmission interference.

► Keep HF devices such as cell phones a minimum distance of

approx. 1 meter away to prevent incorrect measurements or

wireless transmission interference.

► The actual transmission output of HF equipment may require

minimum distances of more than 1 meter. Details can be found at

www.seca.com.

6 •

17-10-07-651-100a/07-2019S

Preventing electric shock WARNING!

Electric shock

► Set up the device so that the power supply socket is easy to reach

and the device can be disconnected from the power supply quickly.

► Ensure that your local power supply matches the information on the

power supply unit.

► Do not touch the power supply unit with wet hands.

► Do not use extension cables or power strips.

► Make sure that cables are not pinched or damaged by sharp edges.

► Make sure that cables do not come into contact with hot objects.

► Do not operate the device at an altitude of more than 3000 m above

sea level.

Preventing injuries and infections WARNING!

Injury from falls

► Ensure that the device is positioned firmly and level.

► Route connecting cables (if present) in such a way that neither user

nor patient can trip over them.

► The device is not designed as a standing aid. Assist people with

limited motor skills when they are getting up, e.g. from a wheelchair.

► Make sure that the patient does not step onto and off the weighing

platform right at the edges.

► Make sure that the patient steps onto and off the weighing platform

slowly and safely.

WARNING!

Danger of slipping

► Ensure that the weighing platform is dry before the patient steps

onto it.

► Ensure that the patients feet are dry before he or she steps onto the

weighing platform.

► Make sure that the patient steps onto and off the weighing platform

slowly and safely.

WARNING!

Risk of infection

► Before and after every measurement, wash your hands to reduce

the risk of cross-contamination and nosocomial infections.

► Hygienically reprocess the device regularly as described in the

respective section in this document.

► Make sure that the patient has no infectious diseases.

► Make sure that the patient has no open wounds or infectious skin

alterations, which may come into contact with the device.

Safety information • 7

English

17-10-07-651-100a/07-2019S

Preventing damage to device NOTICE!

Damage to device

► Ensure that no liquids enter the device. They can damage the

electronics.

► Switch off the device before disconnecting the power supply unit

from the mains socket.

► For devices with power supply operation: Disconnect the power

supply unit from the mains socket if you intend to not use the device

for a longer period of time. Only this way it can be ensured that the

device is de-energized.

► For devices with battery or rechargeable battery operation: If you do

not use the device for an extended period of time, remove batteries

or rechargeable batteries. Only this way it can be ensured that the

device is de-energized.

► Make sure not to drop the device.

► Do not expose the device to any impacts or vibrations.

► Perform function controls regularly as described in the relevant

section in this document. Do not operate the device if it is damaged

or not working properly.

► Ensure that there is no heat source in the immediate vicinity. Do not

expose to direct sunlight. The excessive temperature could damage

the electronics.

► Avoid rapid temperature fluctuations. When the device is

transported so that a temperature difference of more than 20 °C

occurs, it must stay turned off for at least 2 hours before it can be

turned on again. Otherwise, condensation water will form which can

damage the electronics.

► Use the device only in the intended ambient conditions.

► Store the device only in the intended storage conditions.

► Do not use aggressive or abrasive cleaning agents.

► Do not use organic solvents (e.g. white spirit or petroleum spirit).

Handling measuring results CAUTION!

Patient hazard

In order to avoid misinterpretations, measuring results for medical use

must be displayed and used in SI units (weight: kilogrammes, length:

metres) only. Some devices offer the ability to display measuring

results in other units. This is only an additional function.

► Use the results exclusively in SI units.

► The use of measuring results in non-SI units is the sole responsibility

of the user.

NOTICE!

Inconsistent measuring results

► Before you electronically save measured values determined using

this device and use them further (e.g. in seca PC software or in an

EMR system), make sure that the measured values are plausible.

► If measured values are transmitted to seca PC software or an EMR

system, make sure prior to further use that the measured values are

plausible and are assigned to the correct patient.

8 •

17-10-07-651-100a/07-2019S

Handling packaging material WARNING!

Risk of suffocation

Packaging material made of plastic foil (bags) is a choking hazard.

► Keep packaging material out of reach of children.

► In the event that the original packing material may not be available

anymore, only use plastic bags with security holes in order to reduce

the risk of suffocation. Use recyclable materials if possible.

NOTE

Keep the original packing material for future use (e.g. returning for ser-

vicing).

Handling batteries and

rechargeable batteries

WARNING!

Personal injury as a result of improper handling

Batteries and rechargeable batteries contain harmful substances

which may explode if not handled properly.

► Do not try to recharge batteries.

► Do not expose (rechargeable) batteries to heat.

► Do not burn (rechargeable) batteries.

► If acid is leaking out, avoid contact with the skin, eyes and mucous

membranes. Rinse affected areas with plenty of clean water and

seek medical help at once.

NOTICE!

Damage to device and malfunctions with improper handling

► Only use the type of (rechargeable) battery specified in this

document.

► When replacing (rechargeable) batteries, always replace a complete

set at a time.

► Do not short-circuit (rechargeable) batteries.

► If you do not use the device for a long period of time, remove the

batteries (incl. rechargeable batteries). This prevents acid from leak-

ing into the device.

► If acid leaked into the device, discontinue use. Have the device

checked by an authorised seca Service partner and repaired if

necessary.

Overview • 9

English

17-10-07-651-100a/07-2019S

3. OVERVIEW

3.1 View of device

Rear view

Item Device component Function

Display head

For supporting the display unit and housing the cables and batteries

Display unit

Serves as the central operating and display element

Column

For supporting the display head and the measuring rod

Column holder

For supporting the column

Power supply

connection socket

For connecting a seca plug-in power supply unit

Weighing platform

For weighing patients

Battery compartment

To take type AA batteries, 1.5 V

Measuring rod

For measuring height

Head slide

For sliding the measuring flap onto the lower telescopic element

Read-off edge 1

For reading off measuring results in measuring range 1

Read-off edge 2

For reading off measuring results in measuring range 2

Lower telescopic

element

For measuring height in measuring range 1: Up to 1.22 m

Upper telescopic

element

For measuring height in measuring range 2: From 1.22 m

Measuring flap

Serves as a head stop for measuring height

Latch

For releasing and latching the head slide

10 •

17-10-07-651-100a/07-2019S

3.2 Display unit controls

Cover panel

For covering the cables

Recessed handle

For transporting the measuring station

USB interface

For transmitting the weight values displayed to the customer’s own software

solution (if you have any questions, contact seca Service)

Battery cable socket

For connecting the battery cable

Connecting cable

socket

For connecting the connecting cable

Item Device component Function

Item Control Function

On/off key

- Switch the device on and off

BMI kg/lbs key

• During the measurement procedure:

- Activate BMI mode (press key briefly)

- Switch between the units kilograms and pounds (press and hold key) (function

depends on variant)

• In BMI mode:

- Confirm height value and display BMI (press key briefly)

- Exit BMI mode (press key briefly again)

Tare  key

• During the measurement procedure:

- Activate/deactivate

Tare function

• In BMI mode:

- Reduce height value

Hold  key

• During the measurement procedure:

- Activate/deactivate

Hold function

• In BMI mode:

- Increase height value

Overview • 11

English

17-10-07-651-100a/07-2019S

3.3 Symbols in the display

3.4 Markings on the device and on the type plate

EFGH

Item Symbol Meaning

Batteries are low

Weight value in kilograms

lbs

Weight value in pounds

Height in centimeters

BMI

Body mass index

NET

Additional weight tared off (Tare)

HOLD Weight value is displayed permanently (Hold)

Non-verifiable function active

Operation with power supply unit

Text/symbol Meaning

Name and address of manufacturer, date of manufacture

Model number

Serial number, consecutive

ProdID

Product identification number, consecutive

Approval Type

Type designation of design approval

Follow instructions for use

Medical electrical device, Type B

Value in mass units (non-verified models)

States the difference between two consecutive display values

12 •

17-10-07-651-100a/07-2019S

3.5 Markings on the packaging

Device complies with EU directives

FCC symbol (USA)

FCC ID

For USA: Device license number from the Federal Communications Commission (FCC)

For Canada: Device license number from Industry Canada

Type plate on the power supply connection socket

• xx V: Supply voltage required

• max xx A: Maximum current consumption

• : Note polarity of connector plug

• : Operate device with direct current

Do not dispose of device with household waste

Text/symbol Meaning

0123

use compatible

seca adapter only

x-y V

max. xx A

Protect from moisture

Arrows indicate top of product

Transport and store in an upright position

Fragile

Do not throw or drop

Permitted min. and max. temperature for transport and

storage

Permitted min. and max. humidity for transport and

storage

Open packaging here

Packaging material can be disposed of through recycling

programs

Starting up device • 13

English

17-10-07-651-100a/07-2019S

4. STARTING UP DEVICE

4.1 Scope of delivery

4.2 Assembling the device

NOTE

• Use an assistant to perform the assembly.

• We recommend placing the components on the floor and only set-

ting the device in an upright position once you have fitted the mea-

suring rod and the column.

Item Component Pcs.

Weighing platform with column holder

Display head with display unit and connecting cable

Measuring rod

Column (with four pre-fitted screws)

Spacer sleeves

Slot-head screws

Cross-head screws

Lock washers

T20 hex key

Batteries (Type AA, 1.5 V)

Instructions for use

Instructions for Use

seca

Measuring Device

14 •

17-10-07-651-100a/07-2019S

Tools required In addition to the scope of delivery, you require the following tools:

Fitting the measuring rod Proceed as follows to fit the measuring rod to the column.

1. Lie the column down on the floor.

2. Place the spacer sleeves on the bores in the column.

3. Extend the upper telescopic element far enough to expose the lower

assembly bore in the lower telescopic element.

4. Position the measuring rod on the spacer sleeves as shown in the

diagram.

5. Place a slot-head screw in the lower assembly bore and the spacer sleeve

underneath it.

6. Tighten the slot-head screw.

7. Extend the upper telescopic element far enough to expose the upper

assembly bore in the lower telescopic element.

Tool Size

Slot-head screwdriver 1x5.5 mm

Cross-head screwdriver PH 2

Starting up device • 15

English

17-10-07-651-100a/07-2019S

8. Place a slot-head screw in the upper assembly bore and the spacer

sleeve underneath it.

9. Tighten the slot-head screw.

10. Push the upper telescopic element into its lowest position.

Fitting the column Proceed as follows to fit the column to the weighing platform.

1. Lie the column on the floor and position the weighing platform as shown

in the diagram.

2. Hold the weighing platform steady.

3. Push the column and measuring rod into the openings in the column

holder of the weighing platform.

The screws on the column protrude from the underside of the weighing

platform.

4. Place one lock washer in each of the bores for the screws.

16 •

17-10-07-651-100a/07-2019S

5. Tighten the screws using the T20 hex key supplied (recommended tight-

ening torque: 3 Nm).

6. Set the measuring station in an upright position.

Fitting the display head Proceed as follows to fit the display head to the column.

1. Extend the upper telescopic element of the measuring rod approx.

10 cm.

2. Guide the connecting cable of the display head through the center

channel of the column as far as the lower part of the device.

3. Put the display head on the column.

4. Push the upper telescopic element into its lowest position.

5. Place one cross-head screw in each of the two side bores of the column.

6. Tighten the cross-head screws.

7. Place the measuring station on the floor with the display unit facing

upward.

Starting up device • 17

English

17-10-07-651-100a/07-2019S

NOTICE!

Damage due to assembly faults

If the cables are bent at too sharp an angle, they may be damaged

and thus cause a functional failure.

► Route all cables to prevent sharp bends and kinked connectors.

8. Connect the connecting cable:

a) Draw the connecting cable out of the column

b) Route the connecting cable past the cable clip and insert in the

socket on the weighing platform

c) Fix the connecting cable in position with the cable clip

9. Set the measuring station in an upright position.

Switching the positions of the

display unit and the battery

compartment

At the factory, the display unit is fitted to the right-hand operating side of the

display head. The battery compartment is on the left-hand operating side.

Proceed as follows to switch the positions of the display unit and the battery

compartment.

1. Remove the cover panel:

a) Unscrew two cross-head screws

b) Remove the cover panel

2. Remove the battery compartment lid:

a) Hold the battery compartment lid steady

b) Remove the cross-head screw behind the battery compartment lid

c) Remove the battery compartment lid

Right-hand

operating side

Left-hand

operating side

18 •

17-10-07-651-100a/07-2019S

3. Remove the display unit:

a) Undo the cross-head screw behind the display unit

b) Remove cable tie on the cable hook, if present

c) Draw cables out of the cable hook

d) Lift off display unit

4. Switch the positions of the display unit and the battery holder:

a) Put the battery holder in its new position

b) Carefully put the display unit in its new position

5. Route the cables so that they do not dangle out of the display head.

NOTE

When fitting on the right-hand operating side: You can gather all the

cables into the cable hook and secure them with a cable tie if neces-

sary.

6. Fit the display unit:

a) Hold the display unit steady

b) Tighten the cross-head screw behind the display unit

7. Fit the battery compartment lid:

a) Insert the battery compartment lid and hold it steady

b) Tighten the cross-head screw behind the battery compartment lid

Starting up device • 19

English

17-10-07-651-100a/07-2019S

8. Fit the cover panel:

a) Insert cover panel

b) Place and tighten two cross-head screws

Setting up the device 1. Place the device on a firm, level surface.

CAUTION!

Incorrect measurement as a result of incorrect setup location and

incorrect ambient conditions

Soft floors such as wooden hallways, for example, give under the

patient's weight and falsify the measuring result. Incorrect ambient

conditions lead to measuring faults.

► Select a setup location with a level, stable floor in order to achieve

precise measuring results.

► Use the device only in the intended ambient conditions

(➔ “Technical data”, page 29).

2. Remove the protective film from the display.

Disinfecting the device ► Disinfect the following components before initial commissioning

(➔ “Disinfecting”, page 26):

– Column and recessed handle

– Display head and display unit

– Measuring rod, head slide with measuring flap

– Weighing platform

4.3 Transporting the device

The device is equipped with two casters to facilitate transport over short

distances.

1. If necessary, remove the plug-in power supply unit from the power socket

and from the device.

2. Fold down the measuring flap and push the upper telescopic element of

the measuring rod into its lowest position.

3. Take hold of the recessed handle of the device.

4. Tilt the device until it can be moved freely on the casters.

5. Move the device slowly and carefully over door sills.

CAUTION!

Incorrect measurement as a result of incorrect setup location and

incorrect ambient conditions

Soft floors such as wooden hallways, for example, give under the

patient's weight and falsify the measuring result. Incorrect ambient

conditions lead to measurement errors.

► Select a setup location with a level, stable floor in order to achieve

precise measuring results.

► Use the device only in the intended ambient conditions

(➔ “Technical data”, page 29).

6. Transport the device to its new setup location.

7. Set the device in an upright position.

20 •

17-10-07-651-100a/07-2019S

8. If necessary, plug the plug-in power supply unit into the device and into

the power socket (➔ “Connecting the plug-in power supply unit

(optional)”, page 20).

4.4 Establishing the power supply

Inserting batteries You need six AA-type batteries, 1.5 V. To establish the power supply,

proceed as follows:

1. Open the battery compartment:

a) Hold the battery compartment lid steady

b) Remove the cross-head screw behind the battery compartment lid

c) Remove the battery compartment lid

2. Put the new batteries into the battery holder in the battery compartment.

NOTE

• If replacing batteries: Dispose of the old batteries (➔ “Batteries and

rechargeable batteries”, page 30).

• Ensure the correct polarity of the batteries (markings on the battery

holder). If

bAtt appears in the display, you have inserted one of the

batteries the wrong way round or the batteries have discharged. If

batteries are inserted the wrong way round, they must be removed

again immediately.

3. Close the battery compartment:

a) Insert the battery compartment lid

b) Tighten the cross-head screw behind the battery compartment lid

Connecting the plug-in power

supply unit (optional)

The seca plug-in power supply unit is available as an optional accessory.

WARNING!

Personal injury or damage to the device as a result of incorrect power

supply units

Conventional power supply units may deliver a higher voltage than is

indicated on them. The measuring station may overheat, catch fire,

melt or short-circuit.

► Use only original seca plug-in power supply units with controlled

12 V output voltage.

The connection for the plug-in power supply unit is located on the side of

column holder. To establish the power supply, proceed as follows:

La page charge ...

Seca 777 Manuel utilisateur

Marque: Seca

Modèle: 777

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Seca 777 User manual
español: Seca 777 Manual de usuario

Seca 777 Manuel utilisateur

Seca 777 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents