Power Fist 8870685 Le manuel du propriétaire

V4.0 8870685

Please read and understand all instructions before use. Retain this manual for future

reference.

User Manual

HVLP Gravity Paint Gun

8870685 HVLP Gravity Paint Gun V4.0

2 For technical questions call 1-800-665-8685

SPECIFICATIONS

Air Inlet 1.4 in. – 8 NPS

Operating Pressure 20 to 70 PSI

Air Consumption at 40 PSI 6 CFM

Fluid Delivery Type Gravity Feed

Nozzle Size 1.4 mm

Cup Capacity 20 oz.

Material Aluminum, plastic cup

Finish Powder coat

INTRODUCTION

The 1.4 mm HVLP Gravity Paint Gun is ideal for apply paint gently and

evenly over a surface.

SAFETY

WARNING! Read and understand all instructions before using this tool.

The operator must follow basic precautions to reduce the risk of

personal injury and/or damage to the equipment.

Keep this manual for safety warnings, precautions, operating or inspection

and maintenance instructions.

HAZARD DEFINITIONS

Please familiarize yourself with the hazard notices found in this manual. A

notice is an alert that there is a possibility of property damage, injury or

death if certain instructions are not followed.

DANGER! This notice indicates an immediate and specific hazard that will

result in severe personal injury or death if the proper

precautions are not taken.

WARNING! This notice indicates a specific hazard or unsafe practice that

could result in severe personal injury or death if the proper

precautions are not taken.

V4.0 HVLP Gravity Paint Gun 8870685

Visit www.princessauto. com for more information 3

CAUTION! This notice indicates a potentially hazardous situation that may

result in minor or moderate injury if proper practices are not taken.

NOTICE! This notice indicates that a specific hazard or unsafe practice will

result in equipment or property damage, but not personal injury.

WORK AREA

1. Operate in a safe work environment. Keep your work area clean, well-lit

and free of distractions. Place lights so you are not working in a

shadow.

2. Keep anyone not wearing the appropriate safety equipment away from

the work area.

3. Store unused tools properly in a safe and dry location to prevent rust or

damage. Lock tools away and keep out of the reach of children.

4. Do not install or use in the presence of flammable gases, dust or

liquids.

PERSONAL SAFETY

WARNING! Wear personal protective equipment approved by the Canadian

Standards Association (CSA) or American National Standards Institute (ANSI).

PERSONAL PROTECTIVE EQUIPMENT

1. Always wear impact safety goggles that provide front and side

protection for the eyes. Eye protection equipment should comply with

CSA Z94.3-07 or ANSI Z87.1 standards based on the type of work

performed.

2. Wear gloves that provide protection based on the work materials or to

reduce the effects of tool vibration.

3. Wear protective clothing designed for the work environment and tool.

4. Non-skid footwear is recommended to maintain footing and balance in

the work environment.

5. Wear the appropriate rated dust mask or respirator.

6. The air source used with this tool may cause hearing damage. Wear

hearing protection gear with an appropriate Noise Reduction Rating to

withstand the decibel levels.

8870685 HVLP Gravity Paint Gun V4.0

4 For technical questions call 1-800-665-8685

7. The tool may contain high pressure. Use safety glasses and gloves for

protection during operation. Keep hands clear of the exposed rubber

portions of the hose.

PERSONAL PRECAUTIONS

Control the tool, personal movement and the work environment to avoid

personal injury or damage to tool.

1. Do not operate any tool when tired or under the influence of drugs,

alcohol or medications.

2. Avoid wearing clothes or jewelry that can become entangled with the

moving parts of a tool. Keep long hair covered or bound.

3. Do not overreach when operating a tool. Proper footing and balance

enables better control in unexpected situations.

4. Keep your fingers away from the trigger/switch while carrying the tool,

attaching an air hose or an accessory. Lock the trigger/switch safety if

available.

5. Avoid unintentional starts. Be sure that the regulator/throttle switch is

in the neutral or OFF position when not in use and before connecting it

to any air source.

6. Never point the air stream or tool at any point of your body, other people or

animals. Debris and dust ejected at high speed can cause an injury.

7. Serious injury or death may occur from inhaling compressed air. The air

stream may contain carbon monoxide, toxic vapors or solid particles.

Never inhale compressed air directly from the pump or air tool.

SPECIFIC SAFETY PRECAUTIONS

WARNING! DO NOT let comfort or familiarity with product (gained from

repeated use) replace strict adherence to the tool safety rules. If you use

this tool unsafely or incorrectly, you can suffer serious personal injury.

WARNING! Do not use a paint or a solvent containing halogenated

hydrocarbons (HHC) such as methylene chloride or tichloroethane.

Inhaled or ingested HHC can cause serious lung or internal injury.

1. Use the correct tool for the job. This tool was designed for a specific

function. Do not modify or alter this tool or use it for an unintended purpose.

a. Only use a nozzle tip specified for this tool.

V4.0 HVLP Gravity Paint Gun 8870685

Visit www.princessauto. com for more information 5

2. Do not use the tool if any parts are damage broken or misplaced. Repair

or replace the parts.

3. Verify that all connections are secure before operating the paint spray gun.

4. Know how to stop the compressor and bleed the pressure quickly in

case of an emergency. Be thoroughly familiar with the compressor

controls.

5. Always make sure that the area is well ventilated when using indoors.

6. Do not allow the spray to strike you and do not spray toward people or

animals. Do not spray the tool itself or any electrical sources.

7. Tightly recap all containers immediately after mixing and store away

from the spray areas to minimize vapours in the spray area and

eliminate the potential for spills.

8. When spraying, ensure that there are no sources of ignition such as

open fire, cigarettes, sparks, live wires or hot surfaces in the area.

9. Paint or solvent flowing through the equipment is able to produce static

electricity. Static electricity creates a risk of fire or explosion in the presence

of paint or solvent fumes. All parts of the spray system, including the pump,

spray gun and any objects in and around the spray area shall be properly

grounded to protect against static discharge and sparks.

10. Know the contents of the paints and solvents being sprayed. Read all

Safety Data Sheets (SDS) and container labels provided with the paints

and solvents.

a. Do not use homogenate hydrocarbon solvent, as it can react with

aluminum and zinc parts. It can also react with chemicals that are

made for aluminum and zinc parts.

11. Do not leave the spray gun under pressure while unattended. Turn the

compressor off and relieve the pressure in the paint spray gun.

12. Have a working fire extinguisher present while operating the spray paint gun.

13. This paint spray gun is intended for household use only.

AIR TOOL PRECAUTIONS

1. Use only clean and dry compressed air as a power source. Contaminated

or moist air will gradually damage the tool.

8870685 HVLP Gravity Paint Gun V4.0

6 For technical questions call 1-800-665-8685

2. Install an in-line shutoff valve or regulator to allow immediate control

over the air supply in an emergency, even if a hose is ruptured.

3. Discontinue tool use if it does not work properly or air is leaking. Tag or

mark the tool as ‘defective’ or ‘out of service’ until repaired.

4. Check the manufacturer’s maximum pressure rating for air tools and

accessories. Compressor outlet pressure must be regulated to never

exceed the maximum pressure rating of the tool (see Specifications).

Exceeding the maximum PSI rating can create a bursting hazard,

causing injury and property damage.

5. Attach all accessories properly to the tool before connecting the air

supply. A loose accessory may detach or break during operation.

6. Never use oxygen, combustible gas or any other bottled gas as a power

source. Any power source other than an air compressor could cause an

explosion and serious personal injury.

7. Turn OFF the valve and discharge any remaining air pressure after each

use or before adjusting the tool.

8. Do not leave the air tool unattended with its compressed air supply on.

Turn off the compressed air supply and bleed the air tool of any

remaining compressed air before leaving the air tool unattended.

9. Serious injury may occur from loose debris being propelled at high speeds

from the compressed air stream. Always wear OSHA approved safety

glasses to protect the eyes during operation of the air compressor.

10. Always turn off the air compressor and drain tank pressure completely

before attempting maintenance or attaching air tools. Release pressure

slowly from the system.

11. Serious injury or death may occur from inhaling compressed air. The air

stream may contain carbon monoxide, toxic vapors or solid particles.

Never inhale compressed air directly from the pump or air tool.

AIR HOSE PRECAUTIONS

1. Inspect the tool's air hose for cracks, fraying or other faults before each

use. Discontinue use if the air hose is damaged or hissing is heard from

the air hose or couplers. Replace the defective air hose.

V4.0 HVLP Gravity Paint Gun 8870685

Visit www.princessauto. com for more information 7

2. Do not allow people, mobile equipment or vehicles to pass over the

unprotected air hose. Position the air hose away from high traffic

areas, in a reinforced conduit or place planks on both sides of the air

hose to create a protective trench.

3. Prevent damage to the air hose by observing the following:

a. Never carry the tool by the air hose.

b. Keep the air hose behind the tool and out of the tool's work path.

c. Keep the air hose away from heat, oil, sharp edges or moving parts.

d. Do not wrap the air hose around the tool as sharp edges may pierce

or crack the air hose. Gently coil the hose and either hang on a hook

or fasten with a device to keep hose together when storing.

4. A damaged or disconnected air hose under pressure may whip around and

inflict personal injury or damage the work area. Secure the compressor's

air hose to a fixed or permanent structure with clamps or cable ties.

UNPACKING

WARNING! Do not operate the tool if any part is missing. Replace the

missing part before operating. Failure to do so could result in a

malfunction and personal injury.

Remove the parts and accessories from the packaging and inspect for damage.

Make sure that all items in the contents are included.

Contents: • Paint Gun • Filter • Brush • Paint Cup • Cup Lid

ASSEMBLY & INSTALLATION

Numbered references in parenthesis (#1) refer to the included Parts List.

INSTALL AIR COUPLER PLUG

Prepare a standard 1/4 in. NPT coupler plug (sold separately) for use with

your tool.

1. Wrap the external threads of the coupler plug with sealant tape.

a. Wrap tape in a clockwise direction so it will not unravel.

b. Do not tape all the threads. Leave several leading threads

unwrapped for easier alignment.

8870685 HVLP Gravity Paint Gun V4.0

8 For technical questions call 1-800-665-8685

2. Screw the coupler plug into the tool's air inlet and tighten with a

wrench until snug.

3. Run the compressor at a low volume and check the connection for air

leaks. Do not use the tool until all air leaks are repaired or the faulty

component is replaced.

IMPORTANT! Vibration may cause failure if a quick coupler is connected

directly to the air tool. To overcome this, connect a leader hose to the

tool. A quick coupler may then be used to connect the leader hose to the

air line hose.

OPERATION

Proper handling of the spray gun will achieve the desired paint coating. The

recommended paint viscosity will vary according to the paint’s properties

and the painting conditions like the temperature or humidity. Read the paint

instructions before spraying.

HOW TO ADJUST THE PAINT GUN

CAUTION! While under pressure, never remove the fluid control knob lock nut.

1. The amount of fluid applied to a surface is adjusted by tightening or

loosening the fluid adjustment knob (#18). Tighten the knob clockwise

to reduce fluid flow. Loosen the knob counterclockwise to allow more

fluid to flow into the airstream.

2. The pattern adjustment valve knob (#15) will change the pattern from a

circle to an oval. Turn the pattern adjustment valve set counterclockwise

until seated. The spray pattern will be a solid circle. As the knob is

loosened counterclockwise, the circle will change to an oval that

gradually narrows as the knob is loosened.

3. A pressure regulator gauge is required to control the air flow.

PREPARING TO PAINT

1. Screw the fluid adjustment knob and pressure regulator knob in fully in

prevent air and paint flow.

2. Attach the air hose to the air inlet or tool’s pressure regulator.

V4.0 HVLP Gravity Paint Gun 8870685

Visit www.princessauto. com for more information 9

3. Set the air compressor to slightly higher than the recommended

operating pressure, but do not exceed the maximum air pressure (see

Specifications). Air pressure may drop when using a long air hose.

4. Fill the paint cup.

5. Adjust the tool’s pressure regulator to the recommended operating

pressure by either tightening or loosening the air adjusting knob.

a. The ideal pressure will vary depending on viscosity and type of

paint. Make adjustments as needed or thin the paint if too thick.

6. Unscrew the fluid adjusting screw to allow the fluid to flow.

7. Spray against the cardboard backdrop to test the paint coverage. Adjust

the pattern adjustment valve to obtain the desired paint pattern. Adjust

the air and paint flow until the desired coverage is reached.

HOW TO PAINT WITH THE SPRAY GUN

1. Ensure that the gun is between 6 and 8 in. from the workpiece. The needed

distance will vary depending on the atomization pressure and work demand.

a. If the spray gun is too close or too far, the finish will not be even.

As a rule of thumb, the distance from the work surface should

equal the longest dimension of the spray pattern coverage.

2. Grip the gun firmly and keep it perpendicular (90°) to the surface of the

workpiece at all times.

3. Move the gun in a straight horizontal line. Press the trigger after

starting the movement and release before ending the movement. This

ensures an even coating (Fig. 1).

Fig. 1

8870685 HVLP Gravity Paint Gun V4.0

10 For technical questions call 1-800-665-8685

TROUBLESHOOTING

Visit a Princess Auto Ltd. location for a solution if the tool does not function

properly or parts are missing. If unable to do so, have a qualified technician

service the tool.

Problem(s)

Possible

Cause(s)

Suggested Solution(s)

The spray pattern is

intermittent.

1. Presence of air in the

paint circuit.

2. Scratched or plugged

nozzle.

1. Tighten the nozzle using the

wrench provided.

a. Check the amount of fluid in

the container.

b. Ensure that none of the

connector holes are obstructed.

c. Tighten all fittings around the

paint circuit.

2. Clean nozzle or replace if

damaged/scratched.

The center

of the

pattern is

too

narrow.

1. The atomization of the

air pressure is too high.

2. The working material is

too thin.

1. Reduce the quantity of air and

increase the flow of paint.

2. Increase the paint viscosity.

The spray pattern is

uneven.

1. Material has built up on

the outside of the fluid

nozzle tip or center hole

or partially clogged the

nozzle orifice.

2. The fluid nozzle is loose.

1. Clean the head and the nozzle.

a. Ensure that the centering

between the head and nozzle

is precise.

b. Check that the tip of the pin is

not ruined.

2. Replace the head and nozzle if

necessary.

The spray pattern is

arched.

1. Material residue in the

holes is obstructing the

passage of material

2. The nozzle is dirty or

malfunctioning.

3. The atomization cap is

dirty or damaged.

1. Submerge the head in solvent.

2 & 3. Clean and open all closed

holes with a jet of compressed air

or a toothpick.

Do not use pointed metal objects for

this purpose, as you may deform

the hole at the end of the head.

V4.0 HVLP Gravity Paint Gun 8870685

Visit www.princessauto. com for more information 11

There is poor

atomization

with the

spray

concentrated

in the center.

1. The flow of paint is

greater than the

pressure and quantity of

air supplied.

2. Paint viscosity too high.

1. Clean the head and the nozzle.

2. Ensure that the paint is not too

dense and dilute if necessary.

There is little to no

paint output.

1. The fluid passage is

clogged with dirt or the

air holes in the cover are

blocked.

2. Fluid needle stroke is

too small.

1. Remove any obstructions.

2. Adjust fluid needle stroke.

CARE & MAINTENANCE

1. Maintain the tool with care. A tool in good condition is efficient, easier

to control and will have fewer problems.

2. Inspect the tool components periodically. Repair or replace damaged or

worn components. Only use identical replacement parts when servicing.

3. Follow instructions for lubricating and changing accessories.

4. Only use accessories intended for use with this tool.

5. Keep the tool clean, dry and free from oil/grease at all times.

6. Maintain the tool’s labels and name plates. These carry important

information. If unreadable or missing, contact Princess Auto Ltd. for

replacements.

WARNING! Only qualified service personnel should repair the tool. An

improperly repaired tool may present a hazard to the user and/or others.

CLEANING

WARNING! Paint thinner and other solvents may cause health hazards. It

may also combust if exposed to an ignition source. Follow all

instructions that accompany the thinner or solvent for personal

protective equipment, safe handling and first aid. Consult the product’s

Safety Data Sheet (SDS) before use.

8870685 HVLP Gravity Paint Gun V4.0

12 For technical questions call 1-800-665-8685

NOTICE! Remove any o-rings from the spray gun before applying solvent.

Some solvents can interact with the o-ring material and render it

unusable as a seal.

Clean the paint spray gun immediately after you are finished. The paint may

dry and become more difficult to remove. Any paint debris left in the spray

gun may affect the effectiveness and quality of the paint job.

Cleaning the paint spray gun will involve disassembling and reassembling it.

Have solvent, rags, a paint spray gun cleaning kit, toothpicks, a tray to hold

the parts, a paint container and a container to hold the waste solvent. The

solvent used will depend on the type of paint sprayed.

Pour the solvent into a spray bottle for easier application to the paint spray gun.

1. Put safety equipment such as gloves, goggles and a mask to protect

from fumes before cleaning the spray gun.

2. Discharge any air pressure left, then disconnect the paint spray gun

from the air hose.

3. Disconnect the pressure regulator on the tool and set aside.

4. Remove the paint cup lid (#29) and pour any remaining paint either into the

original paint can or a paint can set aside for waste paint.

a. Some paints will solidify and others will remain liquid after disposal. A

separate can should be kept for each type of waste. Contact your local

municipality for instructions on the proper waste disposal of paint.

5. Unscrew the paint cup (#28) and set the paint spray gun aside.

6. Clean the excess paint from the cup and lid with a rag or paper towel.

Dispose of rag/towel as appropriate.

7. Spray solvent into the cup. Use the bottle brush (#32) from the paint spray

gun cleaning kit to remove the paint on the interior of the cup and lid.

Spray with additional solvent as needed. Wipe clean with a rag/towel and

set aside on another clean rag/towel to dry.

8. Remove the needle assembly (#16A and B) from the gun’s body. Remove

the pattern adjustment valve set (#13 to 13H). Wipe down the needle

assembly parts and pattern adjustment valve, except the gasket (#13E),

with solvent. Set aside to dry.

V4.0 HVLP Gravity Paint Gun 8870685

Visit www.princessauto. com for more information 13

9. Hold the paint spray gun body (#12) over the waste solvent container with

the air cap in a downward position. Spray solvent into the fluid connector

and let the waste solvent drain out of the gun body. Spray more solvent

into the fluid connector while holding the gun body in place and let drain.

a. A water-based solvent may corrode the paint spray gun’s internal

mechanism. Use a fast drying solvent such as acetone to flush out the

mechanism immediately after using a water-based solvent.

10. Remove the air cap and spray with solvent. Scrub with a wire brush to

remove paint. Use a bottle brush to clean out the air cap opening. Rinse

with solvent.

11. Remove the nozzle (#1) with a wrench, taking care not to scratch or

damage the nozzle. Use a wire brush and solvent to remove paint from the

exterior. Take care not to damage the nozzle holes.

12. Clean paint residue in the nozzle holes with a wooden toothpick to avoid

damaging the nozzle. Use plenty of solvent to soften or remove the paint

residue and poke a wooden toothpick into the holes to clear them. Rinse

and set aside to dry.

a. Paint residue that cannot be removed with a wooden toothpick can be

removed with a metal pick. Take extreme care as the metal picks may

scratch the nozzle hole. A scratch can ruin a nozzle.

13. Spray solvent onto the gun body and scrub with a wire brush and the bottle

brushes to remove paint. Rinse with solvent and set aside until dry.

REASSEMBLY

14. Screw the nozzle into place and carefully tighten with a wrench.

15. Place the air cap back into place and tighten the air cap ring (#3).

16. Apply petroleum jelly to main body of the needle set (#16) before

sliding it back into the gun. Do not apply the jelly to the needle point.

Insert the spring and gasket into the gun body, then screw the fluid

adjustment knob into place. Squeeze the trigger several times to spread

the petroleum jelly. Tighten the screw (#18A) completely to prevent

paint from flowing the next time the cup is filled.

17. Screw the pattern adjustment valve set (#14 to 15A) back into place.

18. Reattach the paint cup and lid, then the pressure regulator.

8870685 HVLP Gravity Paint Gun V4.0

14 For technical questions call 1-800-665-8685

19. Store the tool in a dry location.

20. Dispose of waste solvent and paint in accordance with your local

municipal by-laws.

LUBRICATION

NOTICE! Do not use this tool on an air hose that includes an automatic in-

line lubricator. Air tool oil introduced in the gun could mix with the paint,

clog the gun and damage the tool. It will also affect the quality of the

paint.

NOTICE! Never use a penetrating oil to lubricate an air tool. Penetrating

oil acts as a solvent that will dissolve the tool’s grease packing and may

damage the o-rings, causing the tool to seize or malfunction.

1. All air tools have an internal coating of grease to prevent corrosion

during shipping and storage. Remove this grease by adding a generous

amount of air tool oil in the air inlet and then run the tool under no load

until the exhaust is clear.

2. Turn the gun upside down and squeeze the trigger. Apply a few drops of

air tool oil to the fluid needle’s front bushing. Release the trigger and

apply air tool oil to the fluid needle’s rear bushing. Squeeze the trigger

several times to spread the lubricant.

a. An alternative is to coat the fluid needle near the trigger area with

petroleum jelly during the cleaning process. Avoid coating the fluid

needle’s point.

3. Clean the gun of excess oil. Excess oil can clog the tool and

compromise the tool’s effectiveness at a task.

DISPOSAL

Recycle a tool damaged beyond repair at the appropriate facility.

TROUBLESHOOTING

Visit a Princess Auto Ltd. location for a solution if the tool does not function

properly or parts are missing. If unable to do so, have a qualified technician

service the tool.

V4.0 HVLP Gravity Paint Gun 8870685

Visit www.princessauto. com for more information 15

Problem(s)

Possible Cause(s)

Power Fist 8870685 Le manuel du propriétaire

Power Fist 8870685 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents