Delta 22-590X Manuel utilisateur

Marque: Delta

Modèle: 22-590X

Taper: Manuel utilisateur

Ce manuel convient également à

22-590

13" PORTABLE PLANER

Raboteuse de 330 mm (13 po)

Cepilladora de 330 mm (13")

Instruction manual

Manuel d’utilisation

Manual de instrucciones

www.deltaportercable.com

Français (17)

Español (33)

INSTRUCTIVO DE OPERACIÓN, CENTROS

DE SERVICIO Y PÓLIZA DE GARANTÍA.

LÉASE ESTE INSTRUCTIVO

ANTES DE USAR EL PRODUCTO.

TABLE OF CONTENTS

IMPORTANT SAFETY INSTRUCTIONS ....................2

SAFETY GUIDELINES - DEFINITIONS .....................2

GENERAL SAFETY RULES .......................................3

ADDITIONAL SPECIFIC SAFETY RULES ................4

FUNCTIONAL DESCRIPTION ...................................6

CARTON CONTENTS ...............................................6

ASSEMBLY .................................................................7

OPERATION ...............................................................9

TROUBLESHOOTING ................................................12

MAINTENANCE .......................................................... 12

SERVICE .....................................................................14

ACCESSORIES ...........................................................16

WARRANTY ................................................................16

FRANÇAIS ..................................................................17

ESPAÑOL ....................................................................33

IMPORTANT SAFETY INSTRUCTIONS

Read all warnings and operating instructions before using any tool or equipment. When

using tools or equipment, basic safety precautions should always be followed to reduce the risk of

personal injury. Improper operation, maintenance or modification of tools or equipment could result

in serious injury and property damage. There are certain applications for which tools and equipment

are designed. DELTA Machinery strongly recommends that this product NOT be modified and/or used for any

application other than for which it was designed.

If you have any questions relative to its application DO NOT use the product until you have written DELTA Machinery

and we have advised you. Contact us online at www.deltaportercable.com or by mail at End User Services, DELTA

Machinery, 4825 Highway 45 North, Jackson, TN 38305. In Canada,125 Mural St. Suite 300, Richmond Hill, ON, L4B

1M4.

Information regarding the safe and proper operation of this tool is available from the following sources:

• Power Tool Institute, 1300 Sumner Avenue, Cleveland, OH 44115-2851or online at www.powertoolinstitute.com

• National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201

• American National Standards Institute, 25 West 43rd Street, 4 floor, New York, NY 10036 www.ansi.org - ANSI 01.1

Safety Requirements for Woodworking Machines

• U.S. Department of Labor regulations www.osha.gov

SAVE THESE INSTRUCTIONS!

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual. The information it contains relates to protecting YOUR

SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information.

indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

indicates a potentially haz ard ous situation which, if not avoided, may result in minor or mod er ate injury.

NOTICE

indicates a practice not related to personal injury which, if not avoided, may result in property

damage.

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities

contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• Lead from lead-based paints,

• Crystalline silica from bricks and cement and other masonry products, and

• Arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to

these chemicals: work in a well-ventilated area, and work with approved safety equipment, such as those dust masks

that are specially designed to filter out microscopic particles.

1. For your own safety, read the instruction manual

before operating the machine. Learning the machine’s

application, limitations, and specific hazards will greatly

minimize the possibility of accidents and injury.

2. Wear eye and hearing protection and always use

safety glasses. Everyday eyeglasses are not safety

glasses. Use certified safety equipment. Eye protection

equipment should comply with ANSI Z87.1 standards.

Hearing equipment should comply with ANSI S3.19

standards.

3. Wear proper apparel. Do not wear loose clothing,

gloves, neckties, rings, bracelets, or other jewelry which

may get caught in moving parts. Nonslip protective

footwear is recommended. Wear protective hair covering

to contain long hair.

4. Do not use the machine in a dangerous environment.

The use of power tools in damp or wet locations or in rain

can cause shock or electrocution. Keep your work area

well-lit to prevent tripping or placing arms, hands, and

fingers in danger.

5. Do not operate electric tools near flammable liquids

or in gaseous or explosive atmospheres. Motors and

switches in these tools may spark and ignite fumes.

6. Maintain all tools and machines in peak condition.

Keep tools sharp and clean for best and safest

performance. Follow instructions for lubricating and

changing accessories. Poorly maintained tools and

machines can further damage the tool or machine and/or

cause injury.

7. Check for damaged parts. Before using the machine,

check for any damaged parts. Check for alignment of

moving parts, binding of moving parts, breakage of parts,

and any other conditions that may affect its operation.

A guard or any other part that is damaged should be

properly repaired or replaced with DELTA or factory

authorized replacement parts. Damaged parts can cause

further damage to the machine and/or injury.

8. Keep the work area clean. Cluttered areas and benches

invite accidents.

9. Keep children and visitors away. Your shop is a

potentially dangerous environment. Children and visitors

can be injured.

10. Reduce the risk of unintentional starting. Make sure

that the switch is in the “OFF” position before plugging in

the power cord. In the event of a power failure, move the

switch to the “OFF” position. An accidental start-up can

cause injury. Do not touch the plug’s metal prongs when

unplugging or plugging in the cord.

11. Use the guards. Check to see that all safety devices are

in place, secured, and working correctly to prevent injury.

12. Remove adjusting keys and wrenches before starting

the machine. Tools, scrap pieces, and other debris can

be thrown at high speed, causing injury.

13. Use the right machine. Don’t force a machine or an

attachment to do a job for which it was not designed.

Damage to the machine and/or injury may result.

14. Use recommended accessories. The use of

accessories and attachments not recommended by

DELTA may cause damage to the machine or injury to the

user.

15. Use the proper extension cord. Make sure your

extension cord is in good condition. When using an

extension cord, be sure to use one heavy enough to carry

the current your product will draw. An undersized cord

will cause a drop in line voltage, resulting in loss of power

and overheating. See the Extension Cord Chart for the

correct size depending on the cord length and nameplate

ampere rating. If in doubt, use the next heavier gauge.

The smaller the gauge number, the heavier the cord.

16. Secure the workpiece. Use clamps or a vise to hold the

workpiece when practical. Loss of control of a workpiece

can cause injury.

17. Feed the workpiece against the direction of the

rotation of the blade, cutter, or abrasive surface.

Feeding it from the other direction will cause the

workpiece to be thrown out at high speed.

18. Don’t force the workpiece on the machine. Damage to

the machine and/or injury may result.

19. Don’t overreach. Loss of balance can make you fall into

a working machine, causing injury.

20. Never stand on the machine. Injury could occur if the

tool tips, or if you accidentally contact the cutting tool.

21. Never leave the machine running unattended. Turn

the power off. Don’t leave the machine until it comes to a

complete stop. A child or visitor could be injured.

22. Turn the machine “OFF”, and disconnect the machine

from the power source before installing or removing

accessories, changing cutters, adjusting or changing

set-ups. When making repairs, be sure to lock the start

switch in the “OFF” position. An accidental start-up can

cause injury.

23. Make your workshop childproof with padlocks,

master switches, or by removing starter keys. The

accidental start-up of a machine by a child or visitor

could cause injury.

24. Stay alert, watch what you are doing, and use

common sense. Do not use the machine when you

are tired or under the influence of drugs, alcohol, or

medication. A moment of inattention while operating

power tools may result in injury.

25.

Use of this tool can generate and

disperse dust or other airborne particles, including

wood dust, crystalline silica dust and asbestos dust.

Direct particles away from face and body. Always operate

tool in well ventilated area and provide for proper dust

removal. Use dust collection system wherever possible.

Exposure to the dust may cause serious and permanent

respiratory or other injury, including silicosis (a serious

lung disease), cancer, and death. Avoid breathing the

dust, and avoid prolonged contact with dust. Allowing

dust to get into your mouth or eyes, or lay on your skin

may promote absorption of harmful material. Always

use properly fitting NIOSH/OSHA approved respiratory

protection appropriate for the dust exposure, and wash

exposed areas with soap and water.

GENERAL SAFETY RULES

Failure to follow these rules may result in serious personal injury.

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.

ADDITIONAL SPECIFIC SAFETY RULES

SAVE THESE INSTRUCTIONS. Refer to them often and use them to instruct others.

1. DO NOT OPERATE THIS MACHINE until it is

completely assembled and installed according to

the instructions. A machine incorrectly assembled

can cause serious injury.

2. OBTAIN ADVICE from your supervisor, instructor,

or another qualified person if you are not thoroughly

familiar with the operation of this machine.

Knowledge is safety.

3. FOLLOW ALL WIRING CODES and recommended

electrical connections to prevent shock or

electrocution.

4. KEEP KNIVES SHARP and free from rust and

pitch. Dull or rusted knives work harder and can

cause kickback.

5. NEVER TURN THE MACHINE “ON” before clearing

the table of all objects (tools, scraps of wood, etc.).

Flying debris can cause serious injury.

6. NEVER TURN THE MACHINE “ON” with the work-

piece contacting the cutterhead. Kickback can

occur.

7. SECURE THE MACHINE TO A SUPPORTING

SURFACE to prevent the machine from sliding,

walking or tipping over.

8. PROPERLY SECURE THE KNIVES IN THE CUTTER-

HEAD before turning the power “ON”. Loose

blades may be thrown out at high speeds causing

serious injury.

9. DO NOT PLACE THE POWER CORD under the

cutterhead when moving or storing.

10. AVOID AWKWARD OPERATIONS AND HAND POSI-

TIONS. A sudden slip could cause a hand to move

into the knives.

11. KEEP ARMS, HANDS, AND FINGERS away from

the cutterhead, the chip exhaust opening, and the

feed rollers to prevent severe cuts.

12. NEVER REACH INTO THE CUTTERHEAD AREA

while the machine is running. Your hands can be

drawn into the knives.

13. DO NOT STAND IN LINE OF THE WORKPIECE.

Kickback can cause injury.

14. ALLOW THE CUTTERHEAD TO REACH FULL

SPEED before feeding a workpiece.

15. WHEN PLANING BOWED STOCK, place the concave

(cup down) side of the stock on the table and cut

with the grain to prevent kickback.

16. DO NOT FEED A WORKPIECE that is warped, contains

knots, or is embedded with foreign objects (nails,

staples, etc.). Kickback can occur.

17. DO NOT FEED A SHORT, THIN, OR NARROW

WORKPIECE INTO THE MACHINE. Your hands can

be drawn into the knives and/or the workpiece can

be thrown at high speeds. See the “OPERATION”

section of this instruction manual for details.

18. DO NOT FEED A WORKPIECE into the outfeed end of

the machine. The workpiece will be thrown out of

the opposite side at high speeds.

19. REMOVE SHAVINGS ONLY with the power “OFF” to

prevent serious injury.

20. USE FOR WOOD ONLY. Do not plane man-made

materials.

21. PROPERLY SUPPORT LONG OR WIDE WORK-

PIECES. Loss of control of the workpiece can

cause serious injury.

22. NEVER PERFORM LAYOUT, ASSEMBLY or set-up

work on the table/work area when the machine is

running. Serious injury will result.

23. TURN THE MACHINE “OFF”, DISCONNECT IT

FROM THE POWER SOURCE, and clean the table/

work area before leaving the machine. LOCK THE

SWITCH IN THE “OFF” POSITION to prevent

unauthorized use. Someone else might accidentally

start the machine and cause injury to themselves

or others.

24. ADDITIONAL INFORMATION regarding the safe

and proper operation of power tools (i.e. a safety

video) is available from the Power Tool Institute,

1300 Sumner Avenue, Cleveland, OH 44115-

2851 (www.powertoolinstitute.com). Information

is also available from the National Safety Council,

1121 Spring Lake Drive, Itasca, IL 60143-3201.

Please refer to the American National Standards

Institute ANSI 01.1 Safety Requirements for

Woodworking Machines and the U.S. Department

of Labor Regulations.

POWER CONNECTIONS

A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should

be protected with a time delay fuse. NOTE: Time delay fuses should be marked “D” in Canada and “T” in the US. If

an extension cord is used, use only 3-wire extension cords which have 3-prong grounding type plugs and matching

receptacle which will accept the machine’s plug. Before connecting the machine to the power line, make sure the switch

is in the “OFF” position and be sure that the electric current is of the same characteristics as indicated on the machine.

All line connections should make good contact. Running on low voltage will damage the machine.

Do not expose the machine to rain or operate the machine in damp locations.

MOTOR SPECIFICATIONS

Your machine is wired for 120 volt, 60 Hz alternating current. Before connecting the machine to the power source, make

sure the switch is in the “OFF” position.

GROUNDING INSTRUCTIONS

This machine must be grounded while in use to protect the operator from electric shock.

GROUNDED OUTLET BOX

CURRENT

CARRYING

PRONGS

GROUNDING BLADE

IS LONGEST OF THE 3 BLADES

GROUNDING MEANS

ADAPTER

1. All grounded, cord-connected machines:

In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to

reduce the risk of electric shock. This machine is equipped with an electric cord having an equipment-grounding

conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and

grounded in accordance with all local codes and ordinances.

Do not modify the plug provided - if it will not fit the outlet, have the proper outlet installed by a qualified electrician.

Improper connection of the equipment-grounding conductor can result in risk of electric shock. The conductor with

insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor.

If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor

to a live terminal.

Check with a qualified electrician or service personnel if the grounding instructions are not completely understood,

or if in doubt as to whether the machine is properly grounded.

Use only 3-wire extension cords that have 3-prong grounding type plugs and matching 3-conductor receptacles that

accept the machine’s plug, as shown in Fig. A.

Repair or replace damaged or worn cord immediately.

2. Grounded, cord-connected machines intended for use on a supply circuit having a nominal rating less than

150 volts:

If the machine is intended for use on a circuit that has an outlet that looks like the one illustrated in Fig. A, the

machine will have a grounding plug that looks like the plug illustrated in Fig. A. A temporary adapter, which looks like

the adapter illustrated in Fig. B may be used to connect this plug to a matching 2-conductor receptacle as shown

in Fig. B, if a properly grounded outlet is not available. The temporary adapter should be used only until a properly

grounded outlet can be installed by a qualified electrician. The green-colored rigid ear, lug, and the like, extending

from the adapter must be connected to a permanent ground such as a properly grounded outlet box. Whenever the

adapter is used, it must be held in place with a metal screw.

NOTE: In Canada, the use of a temporary adapter is not permitted by the Canadian Electric Code.

In all cases, make certain that the receptacle in question is properly grounded. If you are not sure,

have a qualified electrician check the receptacle.

EXTENSION CORDS

Use proper extension cords. Make

sure your extension cord is in good condition and

is a 3-wire extension cord which has a 3-prong

grounding type plug and matching receptacle which

will accept the machine’s plug. When using an

extension cord, be sure to use one heavy enough to

carry the current of the machine. An undersized cord

will cause a drop in line voltage, resulting in loss of

power and overheating. Fig. C shows the correct

gauge to use depending on the cord length. If in

doubt, use the next heavier gauge. The smaller the

gauge number, the heavier the cord.

MINIMUM GAUGE EXTENSION CORD

RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES

Ampere

rating Volts

Total

length of

cord in

feet

Gauge of

extension cord

0-6 120

up to

25 18 AWG

0-6 120 25-50 16 AWG

0-6 120 50-100 16 AWG

0-6 120 100-150 14 AWG

6-10 120

up to

25 18 AWG

6-10 120 25-50 16 AWG

6-10 120 50-100 14 AWG

6-10 120 100-150 12 AWG

10-12 120

up to

25 16 AWG

10-12 120 25-50 16 AWG

10-12 120 50-100 14 AWG

10-12 120 100-150 12 AWG

12-16 120

up to

25 14 AWG

12-16 120 25-50 12 AWG

12-16 120

GREATER THAN 50 FEET NOT RECOMMENDED

Fig. C

Fig. A

Fig. B

FOREWORD

The DELTA Model 22-590 is a 13" (330 mm) Portable Planer that has a cutting capacity of 13" (330mm) wide, 6" (152mm)

thick and 1/8" (3.2 mm) deep. This machine has a powerful 15 amp 120 volt motor with a three-knife cutterhead.

FUNCTIONAL DESCRIPTION

CARTON CONTENTS

NOTICE: The photo on the manual cover illustrates the current production model. All other illustrations contained in

the manual are representative only and may not depict the actual labeling or accessories included. These are intended

to illustrate technique only.

UNPACKING AND CLEANING

Carefully unpack the machine and all loose items from the shipping container. Peel protective film from the table surface.

Figures 1A and 1B illustrate the planer and all loose items supplied with your machine. Refer to the section of this

manual entitled “REPLACING KNIVES” to remove the cutterhead guard. Remove the rust-preventative oil from

unpainted surfaces using a soft cloth moistened with mineral spirits, paint thinner or denatured alcohol.

Do not use highly volatile solvents such as gasoline, naphtha, acetone or lacquer thinner for cleaning your machine.

After cleaning, cover the unpainted surfaces with a good quality household floor paste wax.

Take care when you clean the cutterhead. The knives in the cutterhead are very sharp. After cleaning the

cutterhead, replace the cutterhead guard.

1. Planer

2. Dust Collection Attachment

3. Cutterhead Adjusting Handle

4. Cutterhead Lock Handle

5. Cutterhead Wrench and Handle Combination

This machine weighs about 75 pounds. Use a helper to lift or move it.

6. M6 Star Socket Head Screw

7. M6 Star Socket Head Screw and Washer

8. 6 mm Washer

Fig. 1A

Fig. 1B

ASSEMBLY

To reduce the risk of injury, turn unit off and disconnect it from power source before installing and

removing accessories, before adjusting or when making repairs. An accidental start-up can cause injury.

HOW TO INSTALL THE DUST COLLECTION ATTACHMENT

Fig. 4Fig. 3

1. Remove the two screws (A) Fig. 1C that secure the dust deflector.

2. Remove the dust deflector (B) Fig. 2.

3. Place the dust collection attachment (C) Fig. 3 in the slots provided.

4. Attach the dust collection attachment with the four M6 star socket head screws (D) Fig. 4. Two of these screws were

removed in STEP 1. Tighten all fasteners securely.

5. Reverse the procedure for installing the dust deflector. Install the dust deflector with the label up and curved lip

pointing down.

Fig. 1C

Fig. 2

Disconnect the machine from the power source.

You have two options for dust management. The  rst is the dust de ector and the second is the dust collection attach-

ment to attach your machine to a dust collector.

HOW TO PREPARE FOR DUST MANAGEMENT

When using the dust collection attachment, do not operate the unit without a hose connected and a dust

collector in operation.

ASSEMBLY TOOLS REQUIRED

Cutterhead Wrench (Supplied)

ASSEMBLY TIME ESTIMATE

Approximately 1/2 hour

1. Attach the cutterhead adjustment handle (A) Fig. 6 to the shaft (B), with the flat on the shaft engaged with the flat in

the handle.

2. Fasten the cutterhead adjustment handle to the shaft using the M6 x 20mm star socket head screw and

lockwasher with the supplied cutterhead wrench (Fig. 7).

NOTE: The cutterhead adjustment handle is supplied with markings (C) Fig. 8 to make your cuts accurate.

Use the supplied wrench to attach the cutterhead lock

handle (A) Fig. 5 to the shaft (B) with the M6 x 20mm star

socket head screw and lockwasher.

HOW TO ATTACH THE CUTTERHEAD LOCK HANDLE

Fig. 5

HOW TO ATTACH THE CUTTERHEAD ADJUSTMENT HANDLE

Fig. 6

Fig. 7

Fig. 8

HOW TO FASTEN THE PLANER TO A SUPPORTING SURFACE

Four attachment holes are provided for mounting the

planer to a stand or work surface. These holes are

located under the infeed and outfeed tables as shown in

Fig. 9.

Before operation, secure the planer to the supporting surface. Four holes (two of which are shown at (A)

Fig. 9) are provided for this purpose.

Operate the planer on a flat, level surface.

Fig. 9

Use ONLY DELTA accessory stands.

OPERATION

OPERATIONAL CONTROLS AND ADJUSTMENTS

HOW TO START AND STOP THE PLANER

To turn the planer “ON”, lift the paddle (A) Fig. 10. To turn the tool “OFF”, push the paddle down (Fig. 11).

IMPORTANT: When the machine is not in use, the switch should be locked in the “OFF” position to prevent unauthor-

ized use. Place a padlock (B) Fig. 12 with a 1/4" (6.3 mm) diameter shackle through the hole on the left side of the switch

cover and through the hole in the switch paddle. Lock the padlock.

Ensure that the lock prevents the switch from being turned on.

Fig. 11

Fig. 12

Fig. 10

HOW TO USE THE CUTTERHEAD LOCK

The cutterhead lock (A) Fig. 13 helps to eliminate snipe

in the board that is being planed. Snipe can also be

eliminated by butting boards end to end and feeding

them through the planer. Long boards should always be

supported, when feeding them through the planer to help

eliminate snipe.

Fig. 13

The head assembly contains the cutterhead, feed

rollers, chip deflector and motor. Raising and lowering

the head assembly controls the depth of cut. To adjust

the head assembly, rotate the cutterhead lock handle

(A) Fig. 13 counterclockwise to unlock the cutterhead.

Turn the cutterhead adjusting handle clockwise to raise

or counter-clockwise to lower the cutterhead. One

revolution of handle (A) Fig. 14 will move the cutterhead

up or down 1/16" (1.6 mm).

HOW TO ADJUST THE HEAD ASSEMBLY

Fig. 14

RECOMMENDED DEPTH OF CUT

NOTE: One revolution of the cutterhead adjusting

handle will move the cutterhead up or down 1/16"

(1.6 mm).

You can make a 1/8" (3.2 mm) depth-of-cut in soft

woods up to 6" (152mm) wide and in hard woods up to

4" (102 mm) wide. (Fig. 16)

For 6" (152 mm) through 13" (330 mm) wide soft wood,

use a maximum depth-of-cut of 1/16" (1.6 mm). For 6"

(152 mm) through 13" (330 mm) wide hard wood, use a

maximum depth-of-cut of 3/64" (1.2 mm) (Fig. 16).

IMPORTANT: A shallow depth-of-cut will produce a

better finish.

To set the minimum depth to which the carriage can trav-

el with the depth stop:

1. Check to see that the carriage is set above 1-1/4"

before trying to set the depth stop.

2. Turn the dial on the front left of the planer until the

desired thickness setting aligns with the indicator line

(B) Fig. 17.

3. Lock the gauge in place by turning the wheel on the

inside of the gauge (Inset – Fig. 17).

4. Plane the workpiece at desired increments until the

correct  nal thickness is achieved.

NOTE: Do not use force to lower the carriage below the

level that the depth stop indicates. Permanent damage to

the height adjustment system on your planer will result.

1. Slide approximately 3" of the workpiece (B) Fig. 15

under the middle of the carriage.

2. Be sure that the workpiece is lying  at against the

base of the planer. If the workpiece is inserted at an

angle, the reading may be inaccurate.

3. Lower the carriage on the workpiece until the material

removal bar engages the wood. You will see the red

arrow moving up the scale to indicate the amount to

be removed with the carriage at that height.

4. Adjust the carriage height until the desired depth of

cut appears on the gauge.

5. Pull the material out from under the carriage.

6. Turn the unit on and feed your material into the cutter

head.

HOW TO USE THE MATERIAL REMOVAL GAUGE

Your planer is equipped with a material removal gauge (A) Fig. 15. It is used to indicate the amount of wood that will

be removed in one pass with the carriage set at its current height. The material removal gauge reads across the entire

width of the planer head.

HOW TO USE THE DEPTH STOP

Your planer is equipped with a depth stop (A) Fig. 17 for repetitive planing. Any thickness between 1/8" and 1-1/4" can

be selected using the scale on the depth stop. Detents are provided at 1/8", 1/4", 1/2", 3/4", 1", and 1-1/4".

NOTE: Do not exceed the recommended depth of cut for various widths of material, shown in the “RECOMMENDED

DEPTH OF CUT” section below.

Do not turn the unit “ON” with the workpiece in position.

Fig. 15

Fig. 17

1/16"

(1.6 mm)

3/32"

(2.4 mm)

1/8"

(3.2 mm)

(51 mm)

(102 mm)

SOFT WOOD

HARD WOOD

RECOMMENDED DEPTH OF CUT

(152 mm)

(178 mm)

(203 mm)

(229 mm)

10"

(254 mm)

WIDTH OF STOCK

Fig. 16

1. Measure the thickness of a planed board.

2. Set the zero position of the ring (A) Fig. 18 to align with

the arrow (B).

3. Rotate the handle to the desired depth of cut, as

indicated on the ring. Each indicator on the ring is

equivalent to 1/128" (.2 mm) for making minute cuts.

4. Plane the workpiece.

HOW TO USE THE ADJUSTABLE INDEXING RING

Follow these few steps to achieve the best results.

1. True One Face – Feed one face of the board over a jointer, making thin cuts with each pass, until the entire surface

is flat.

2. Plane to Thickness – Place the side you just surfaced in STEP 1 face down and feed the board through the planer,

plane until this side is flat. Then plane both sides of the board until you are satisfied with the thickness, making

thin cuts, alternating sides with each pass. If, during the planing operation, you notice the board twisting, warping

or bowing, repeat STEP 1 and true one face.

3. When planing long stock, provide additional support to the infeed and outfeed end of the workpiece.

4. Always engage the cutterhead lock before planing. Plane with the grain only, and keep table clean. Occasionally, wax

the table surface to reduce friction.

5. Cross-cut the workpiece to its final length.

NOTICE

Feed the wood through the planer at different places on the table to help eliminate uneven wear of the

knives.

MACHINE USE

The cutterhead adjusting handle has an adjustment ring (A) Fig. 18. To use the adjustment ring to make fine adjustments:

PROPER PLANING TECHNIQUES

1. Lower the carriage to the desired height for your  rst pass.

2. Turn the unit on and feed the material into the feed rollers.

3. Examine the  nished cut and adjust the carriage to the appropriate height for your next pass.

4. Feed workpieces through alternating areas of the planer for even blade wear – not just through the center of the

machine. One way to do this is to start with the workpiece on the left in one pass, in the middle on the next and on

the right side for third pass – and then repeat.

NOTE: Flip the board back and forth between each pass.

Do not turn the unit on with the workpiece inserted under carriage. Wait until the roller and cutterhead are

up to full speed before feeding your material into the machine.

For best results, plane both sides of the workpiece to reach desired thickness. For example, if you need to remove 1/8"

from your workpiece, remove 1/16" from each side. This not only allows the workpiece to dry with an even moisture

content, it also produces  ner cuts.

Plane only wood that is free from foreign objects, with no loose knots and as few tight knots as possible.

Do not plane wood that is severely warped, twisted, knotted or bowed.

Do not place your body between the rear of the planer and a stationary object while material is feeding.

Serious injury could result.

MINIMUM/MAXIMUM WIDTH/HEIGHT/DEPTH

NOTE: Always plane in the direction of the grain. Support the workpiece adequately at all times. Planing material less

than 3/4" wide is not recommended. If you must plane narrow material, group several pieces together and plane them as

one wide workpiece whenever possible. The maximum depth of cut your planer can take in one pass is 1/8" (on material

less than 6” wide). Never attempt to modify your planer to take a deeper cut. Follow the recommended depth/width of

cut guidelines shown in Fig. 16 for best results.

Fig. 18

SNIPE

Snipe is a depression made when an unsupported end of your material drops toward the  oor, causing the opposite

end to lift up into the cutter head.

TO AVOID SNIPE

Feed the workpiece into the planer so it is level and remains  at against the base at all times.

Keep the workpiece level throughout planing operation by receiving or “catching” it from the rear of the planer. If you are

planing material that is especially long, the use of additional material support is recommended.

TWISTED, CUPPED AND BOWED WOOD

If both sides of your material are very rough or if the material is cupped, bowed or twisted, your planer may not produce

the desired result. Ideally, you should have at least one level face/surface on your material before you plane. Your thickness

planer will work best with material that has been run through a jointer to produce one  at surface. If you do not have at

least one  at surface or a jointer, see the following recommendations.

TO PLANE TWISTED WOOD

Twisted wood may jam your planer. If a jam occurs, turn the power “OFF”, disconnect the power

supply and raise the carriage to release the workpiece from the cutter.

If your material is only slightly twisted, plane both sides alternating from one to the other until the desired thickness is

reached.

TO PLANE CUPPED WOOD

To obtain the best possible results with cupped wood, rip the material down the middle and plane it as two separate

pieces. Ripping the material reduces the severity of the cup and allows the machine to deliver better results. Understand

that you will have to remove more material on cupped wood to achieve the desired thickness than you would on a normal

board. If ripping the material is not an option, plane one side of the material until  at, then plane the opposite side until it

is also  at.

NOTE: Do not  ip the board back and forth between each pass as recommended by the general planing directions.

TO PLANE BOWED WOOD

The feed rollers and cutter head in your planer will push the bow out of the material as it feeds. However, when the mate-

rial exits the planer, the pressure of the rollers and cutterhead will release allowing the wood to spring back into a bowed

formation. To properly remove the bow, use a jointer.

TROUBLESHOOTING

For assistance with your machine, visit our website at www.deltaportercable.com for a list of service centers or

call the DELTA Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582).

MAINTENANCE

To reduce the risk of injury, turn unit off and disconnect it from power source before installing and remov-

ing accessories, before adjusting or when making repairs. An accidental start-up can cause injury.

HOW TO CHECK, ADJUST, CLEAN AND REPLACE KNIVES

Wear gloves when you remove the knives for sharpening or replacement. The knives in this planer

are very sharp.

Disconnect the machine from the power source.

The knives are sharp. Be careful when removing, handling, or installing knives.

The knives supplied with your planer are double edged and reversible so that you can turn the knives end-for-end when

one edge becomes dull or chipped. To change the knives:

1. Raise the head assembly (B) Fig. 19 to 4" (102 mm) on the “Scale and Pointer”.

2. Remove the screws (A) Fig. 19. Pull the chip deflector or dust collection attachment – whichever is installed – (B)

straight out.

3. Insert the supplied wrench (C) Fig. 20 into the hex hole. Rotate the cutterhead until the cutterhead lock engages.

4. Remove the seven screws (E) Fig. 21 and use magnetic end of the wrench to remove the hold-down bar (F).

5. Place the magnetized end of the wrench (G) Fig. 22 at the center of the knife. Lift the wrench until the knife

(H) separates from the pins. Remove the knife.

6. Repeat steps 3 through 5 to remove the other two knives. Press down the cutterhead lock release and use the

supplied wrench (C) Fig. 20 to rotate the cutterhead lock until the lock engages and the next knife is in position to

be removed.

7. IMPORTANT: After removing all knives from cutterhead, carefully set them aside. Using a cloth rag and isopropyl

alcohol, clean the cutterhead, knives and hold-down bars free of gum, tar and pitch residue. Take special care

to clean the cutterhead under the knife area and the cutterhead radius in front of the knife area. Doing this will

increase the life of your planer.

8. Take this time also to clean the rollers (I) Fig. 22A.

9. Your unit is equipped with double-edged knives. If the second edge of the knife has not been used, rotate the

knife 180 degrees and replace on the cutterhead. Replace the knives if both sides have been used.

10. Attach the hold-down bar (F) Fig. 21 that you removed in STEP 4. Tighten all fasteners securely.

11. Depress the cutterhead lock release and rotate the cutterhead to the next empty position until the cutterhead lock

engages.

12. Repeat steps 9 through 11 to replace the other knives.

13. Reattach the cutterhead guard or dust collection attachment.

Fig. 19

Fig. 20

Fig. 21

Fig. 22

HOW TO ADJUST THE INFEED AND OUTFEED TABLES

Your unit has been factory set to eliminate snipe. If your unit loses

its adjustment and causes snipe, you can adjust the infeed and

outfeed tables to minimize this condition.

1. Place a dime (A) Fig. 23A at each end of the platen (infeed and

outfeed).

2. Place a straight edge (B) across the two dimes. Extend the

straight edge past the leading edge of the infeed and trailing

edge of the outfeed tables.

3. If your tables are properly adjusted, the straight edge will touch

both of the dimes and the edges of the tables (Fig. 23C).

4. If your table needs adjustment, loosen the locknuts (A) Fig. 23B

on the table height-adjustment screws (B). Adjust the screws

up or down to achieve the desired table height.

5. Make sure that both height-adjustment screws contact the

bottom of the table after adjustment.

Fig. 23A Fig. 23B

Fig. 23C

Fig. 22A

SERVICE

The depth adjustment scale (A) Fig. 23D on your planer is

set at the factory. However, with extended use, the depth

adjustment scale could show an incorrect measurement. To

check the depth adjustment scale, plane a piece of scrap

wood, noting the measurement on the depth adjustment

scale. Measure the  nished thickness of the workpiece. If

the thickness of the workpiece does not match the reading

on the depth adjustment scale, loosen the two screws (B)

on the red indicator. Adjust the pointer up or down until its

reading matches the  nished thickness of the workpiece.

Securely re-tighten the screws.

HOW TO CALIBRATE THE DEPTH ADJUSTMENT SCALE

Keep the table clean and free from oil, grease, and pitch.

Treat the table with paste wax to help maintain its smooth

 nish.

BASE MAINTENANCE

Your planer is equipped with an 18 amp circuit breaker. If your planer becomes overloaded and stops operating, turn off

the planer, let the unit sit for 2 minutes and press the reset button (A) Fig. 24 before you resume working.

CIRCUIT BREAKER RESET BUTTON

To prevent the planer from start-

ing unexpectedly if power is interrupted by a circuit

breaker trip, make sure the switch is in the "OFF" po-

sition before restoring power.

NOTE: Circuit breaker overload is often the result of dull

knives. Change your knives on a regular basis to avoid

tripping your breaker. Check your knives before re-set-

ting the circuit breaker and continuing to plane.

BRUSH CHANGE

Your planer is equipped with brush caps (C) Fig. 23D that

are external to the motor. If your brushes need to be re-

placed, begin by acquiring a new set from a DELTA Ma-

chinery service center or a dealer authorized to service

DELTA products. Use only identical DELTA brushes.

Fig. 24

Drive belts are available at extra cost at DELTA authorized service centers. Replacement of the drive belt should be

performed by quali ed service personnel.

REPLACING THE DRIVE BELT

KEEP MACHINE CLEAN

Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth.

NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material.

Wear certified safety equipment for eye, hearing and respiratory protection while using compressed air.

FAILURE TO START

Should your machine fail to start, check to make sure the prongs on the cord plug are making good contact in the

outlet. Also, check for blown fuses or open circuit breakers in the line.

LUBRICATION

Apply household floor paste wax to the machine table, extension table or other work surface weekly. Or use a commercially

available protective product designed for this purpose. Follow the manufacturer’s instructions for use and safety.

REPLACEMENT PARTS

Use only identical replacement parts. For a parts list or to order parts, visit our website at

www.deltaportercableservicenet.com.

You can also order parts from your nearest factory-owned branch, or by calling our Customer Care Center at 1-800-223-7278 to

receive personalized support from highly-trained technicians.

Fig. 23D

FREE WARNING LABEL REPLACEMENT

If your warning labels become illegible or are missing, call

1-800-223-7278

for a free replacement.

AVERTISSMENT

TO PROLONG TOOL LIFE, DURING KNIFE CHANGE

CLEAN ANY PITCH OR WOOD BUILD UP FROM

THE CUTTERHEAD. ALWAYS REMOVE THE

KNIVES BEFORE CLEANING THE

CUTTERHEAD. SEE THE

MAINTENANCE SECTION

OF THE INSTRUCTION

MANUAL FOR

DETAILS.

PARA PROLONGAR LA VIDA ÚTIL DE LA

HERRAMIENTA, DURANTE EL CAMBIO DE

CUCHILLAS, QUITE LA RESINA O LA MADERA

ACUMULADAS EN EL CABEZAL DE CORTE.

SIEMPRE RETIRE LAS CUCHILLAS ANTES DE

LIMPIAR EL CABEZAL DE CORTE. CONSULTE

LA SECCIÓN MANTENIMIENTO DEL MANUAL

DE INSTRUCCIONES PARA OBTENER

DETALLES.

LORS DU CHANGEMENT DE COUTEAU, NETTOYER TOUTE

ACCUMULATION DE RÉSINE OU DE BOIS SUR LA TÊTE DE

COUPE AFIN DE PROLONGER LA DURÉE DE VIE DE

L’OUTIL. TOUJOURS RETIRER LES COUTEAUX

AVANT DE NETTOYER LA TÊTE DE COUPE.

POUR DE PLUS AMPLES

RENSEIGNEMENTS, CONSULTER

LA RUBRIQUE ENTRETIEN

DU MODE D’EMPLOI.

PELIGRO DE LACERACIÓN. MANTENGA LAS MANOS LEJOS DE LAS

PIEZAS EN MOVIMIENTO Y DEL TOMACORRIENTE. NUNCA REALICE

OPERACIONES DE CEPILLADO SIN LOS PROTECTORES OCUBIERTAS.

DESENCHUFE LA HERRAMIENTA ANTES DE REALIZAR REPARACIONES.

RISQUE DE LACÉRATION. ÉLOIGNER LES MAINS DES PIÈCES MOBILES

ET DE LA SORTIE. NE JAMAIS RABOTER SANS LES DISPOSITIFS

DE PROTECTION OU LES COUVERCLES EN PLACE. DÉBRANCHER

AVANT TOUT ENTRETIEN.

LACERATION HAZARD. KEEP HANDS AWAY FROM

MOVING PARTS AND OUTLET. NEVER PERFORM

PLANING OPERATIONS WITH GUARDS OR COVERS

REMOVED. UNPLUG BEFORE SERVICING.

Since accessories other than those offered by DELTA have not been tested with this product,

use of such accessories could be hazardous. For safest operation, only DELTA recommended accessories

should be used with this product.

A complete line of accessories is available from your DELTA Supplier, Porter-Cable•DELTA Factory Service Centers, and

DELTA Authorized Service Stations. Please visit our Web site www.deltaportercable.com for a catalog or for the name

of your nearest supplier.

ACCESSORIES

SERVICE AND REPAIRS

All quality tools will eventually require servicing and/or replacement of parts. For information about DELTA Machinery, its

factory-owned branches, or an Authorized Warranty Service Center, visit our website at www.deltaportercable.com or call our

Customer Care Center at 1-800-223-7278. All repairs made by our service centers are fully guaranteed against defective material

and workmanship. We cannot guarantee repairs made or attempted by others.

You can also write to us for information at DELTA Machinery, 4825 Highway 45 North, Jackson, Tennessee 38305 - Attention:

Product Service. Be sure to include all of the information shown on the nameplate of your tool (model number, type, serial number,

etc.)

Five Year Limited New Product Warranty

DELTA will repair or replace, at its expense and at its option, any new DELTA machine, machine part, or machine accessory which in normal

use has proven to be defective in workmanship or material, provided that the customer returns the product prepaid to a DELTA factory service

center or authorized service station with proof of purchase of the product within five years and provides DELTA with reasonable opportunity

to verify the alleged defect by inspection. For all refurbished DELTA product, the warranty period is 180 days. DELTA will not be responsible

for any asserted defect which has resulted from normal wear, misuse, abuse or repair or alteration made or specifically authorized by anyone

other than an authorized DELTA service facility or representative. Under no circumstances will DELTA be liable for incidental or consequential

damages resulting from defective products. Some states do not allow the exclusion or limitation of incidental or consequential damages, so

the above limitation or exclusion may not apply to you. This warranty is DELTA’s sole warranty and sets forth the customer’s exclusive remedy,

with respect to defective products; all other warranties, express or implied, whether of merchantability, fitness for purpose, or otherwise, are

expressly disclaimed by DELTA. For further detail of warranty coverage and warranty repair information, visit www.deltaportercable.com or call

(888) 848-5175. This warranty gives you specific legal rights and you may have other rights which vary in certain states or provinces.

WARRANTY

To register your tool for warranty service visit our website at www.deltaportercable.com.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold in Latin America,

see country specific warranty information contained in the packaging, call the local company or see website for warranty

information.

LES INSTRUCTIONS IMPORTANTES DE SURETE

Lire toutes instructions d'avertissements et opération avant d'utiliser n'importe

quel outil ou n'importe quel équipement. En utilisant les outils ou l'équipement, les précautions de

sûreté fondamentales toujours devraient être suivies pour réduire le risque de blessure personnelle.

L'opération déplacée, l'entretien ou la modification d'outils ou d'équipement ont pour résultat la

blessure sérieux et les dommages de propriété. Il y a de certaines applications pour lequel outils et l'équipement

sont conçus. La DELTA Machinery recommande avec force que ce produit n'ait pas modifié et/ou utilisé pour

l'application autrement que pour lequel il a été conçu.

Si vous avez n'importe quelles questions relatives à son application n'utilisent pas le produit jusqu'à ce que vous

avez écrit DELTA Machinery et nous vous avons conseillé. La forme en ligne de contact à www.deltaportercable.com

Courrier Postal: Technical Service Manager, DELTA Machinery, 4825 Highway 45 North, Jackson, TN 38305.

Dans Canada,

125 Mural St. Suite 300, Richmond Hill, ON, L4B 1M4.

Information en ce qui concerne l'opération sûre et correcte de cet outil est disponible des sources suivantes:

• Power Tool Institute, 1300 Sumner Avenue, Cleveland, OH 44115-2851 ou en ligne www.powertoolinstitute.com

• National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201

• American National Standards Institute, 25 West 43rd Street, 4 floor, New York, NY 10036 www.ansi.org - ANSI 01.1

Safety Requirements for Woodworking Machines

• U.S. Department of Labor regulations www.osha.gov

CONSERVER CES DIRECTIVES.

MESURES DE SÉCURITÉ – DÉFINITIONS

Ce guide contient des renseignements importants que vous deviez bien saisir. Cette information porte sur VOTRE

SÉCURITÉ et sur LA PRÉVENTION DE PROBLÈMES D’ÉQUIPEMENT. Afin de vous aider à identifier cette information,

nous avons utilisé les symboles ci-dessous.

indique une situation dangereuse imminente qui, si elle n’est pas évitée, causera la mort ou des

blessures graves.

indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait se solder par

un décès ou des blessures graves.

indique une situation potentiellement dangereuse qui, si elle n’est pas évitée pourrait se solder par

des blessures mineures ou modérées.

AVIS

indique une pratique ne posant aucun risque de dommages corporels mais qui par contre, si rien

n’est fait pour l’éviter, pourrait poser des risques de dommages matériels.

Les scies, meules, ponceuses, perceuses ou autres outils de construction peuvent

produire des poussières contenant des produits chimiques reconnus par l’État californien pour causer cancers,

malformations congénitales ou être nocifs au système reproducteur. Parmi ces produits chimiques, on retrouve:

• le plomb dans les peintures à base de plomb;

• la silice cristallisée dans les briques et le ciment ou autres articles de maçonnerie; et

• l’arsenic et le chrome dans le bois ayant subi un traitement chimique (ACC).

Le risque associé à de telles expositions varie selon la fréquence à laquelle on effectue ces travaux. Pour réduire toute

exposition à ces produits: travailler dans un endroit bien aéré, en utilisant du matériel de sécurité homologué tel un

masque antipoussières spécialement conçu pour filtrer les particules microscopiques.

1. Pour sa sécurité personnelle, lire la notice d’utilisation,

avant de mettre la machine. En marche, et pour aussi

apprendre l’application et les limites de la machine

ainsi que les risques qui lui sont particuliers ainsi, les

possibilités d’accident et de blessures seront beaucoup

réduites.

2. Portez des dispositifs de protection des yeux et de

l'ouïe. Utilisez toujours des lunettes de sécurité. Des

lunettes ordinaires ne constituent pas des lunettes de

sécurité. Utilisez des équipements de sûreté homologués.

Les dispositifs de protection des yeux doivent être

conformes aux normes ANSI Z87.1. Les dispositifs de

protection de l'ouïe doivent être conformes aux normes

ANSI S3.19.

3. Porter une tenue appropriée. Pas de cravates, de gants,

ni de vêtements amples. Enlever montre, bagues et autres

bijoux. Rouler les manches. Les vêtements ou les bijoux

qui se trouvent pris dans les pièces mobiles peuvent

entraîner des blessures.

4. Ne pas utiliser la machine dans un environnement

dangereux. L’utilisation d’outils électriques dans des

endroits humides ou sous la pluie peut entraîner des

décharges électriques ou une électrocution. Garder la

zone de travail bien éclairée pour éviter de trébucher ou

d’exposer les doigts, les mains ou les bras à une situation

dangereuse.

5. Ne pas utiliser d’outils électriques à proximité de

liquides inflammables ou dans une atmosphère

gazeuse ou explosive. Les moteurs et interrupteurs des

outils pourraient provoquer des étincelles et enflammer

des vapeurs.

6. Garder les outils et les machines en parfait état.

Garder les outils affûtés et propres afin d’obtenir le

meilleur et le plus sûr rendement. Suivre les instructions

pour lubrifier et changer les accessoires. Les outils et les

machines mal entretenus peuvent se dégrader davantage,

et/ou entraîner des blessures.

7. Inspecter les pièces pour déceler tout dommage.

Avant d’utiliser la machine, la vérifier pour voir s’il n’y a

pas de pièces endommagées. Vérifier l’alignement des

pièces mobiles et si ces pièces ne se coincent pas, la

rupture de pièces, ou toute autre condition pouvant en

affecter le fonctionnement. Toute pièce ou protecteur

endommagé doit être réparé ou remplacé avec le DELTA

ou les pièces de rechange autorisées par usine. Les

pièces endommagées peuvent dégrader davantage la

machine et/ou entraîner des blessures.

8. Garder l’aire de travail propre. Les zones et établis

encombrés favorisent les accidents.

9. Garder les enfants et les visiteurs à distance. L’atelier

est un lieu potentiellement dangereux. Les enfants et les

visiteurs peuvent se blesser.

10. Éviter le démarrage accidentel. S’assurer que

l’interrupteur est sur « OFF » (ARRÊT) avant de brancher

le cordon. En cas de coupure de courant, placer

l’interrupteur à la position «OFF » (ARRÊT). Un démarrage

accidentel peut entraîner des blessures.

11. Utiliser les dispositifs protecteurs. Vérifier que tous les

dispositifs protecteurs sont bien en place, bien fixés et en

bon état de marche pour éviter les blessures.

12. Enlever les clés de réglage et celles de serrage avant

de mettre la machine en marche. Les outils, les chutes

et les autres débris peuvent être projetés violemment et

blesser.

13. Utiliser la bonne machine. Ne pas forcer la machine ou

l’accessoire à faire un travail pour lequel il n’a pas été

conçu. Des dommages à la machine et/ou des blessures

pourraient s’ensuivre.

14. Utiliser les accessoires recommandés. L’utilisation

d’accessoires non recommandés par DELTA peut

RÈGLES DE SÉCURITÉ GÉNÉRALES

L’inobservation de ces règles peut conduire à des blessures graves.

endommager la machine et blesser l’utilisateur.

15. Utiliser le cordon prolongateur approprié. S’assurer

que le cordon prolongateur est en bon état. Lorsqu’un

cordon prolongateur est utilisé, s’assurer que celui-ci est

d’un calibre suffisant pour l’alimentation nécessaire à la

machine. Un cordon d’un calibre insuffisant entraînera

une perte de tension d’où une perte de puissance et

surchauffe. Voir le Tableau sur Les Cordons prolongateurs

pour obtenir le calibre approprié selon la longueur du

cordon et l’ampérage de la machine. S’il y a un doute,

utiliser un cordon d’un calibre supérieur. Plus le chiffre est

petit, plus le fil est gros.

16. Fixer la pièce. Utilisez les brides ou un étau pour tenir

l'objet si pratique. La perte de commande d'un objet peut

causer des dommages.

17. Avancer la pièce dans le sens contraire à la rotation

de la lame, de la fraise ou de la surface abrasive.

L’alimentation dans l’autre sens peut entraîner une

projection violente de la pièce.

18. Ne pas forcer la machine en avançant la pièce trop vite.

Des dommages et/ou des blessures peuvent s’ensuivre.

19. Ne pas se pencher au-dessus de la machine. Une perte

de l’équilibre peut entraîner une chute sur la machine en

marche et causer des blessures.

20. Ne jamais monter sur la machine. On peut se blesser

gravement si la machine bascule ou si l’on touche

accidentellement son outil tranchant.

21. Ne jamais laisser la machine en marche sans

surveillance. Couper le courant. Ne pas quitter la

machine tant qu’elle n’est pas complètement arrêtée. Un

enfant ou un visiteur pourrait se blesser.

22. Mettre la machine à l’arrêt « OFF » et la débrancher

avant d’installer ou d’enlever des accessoires, changer

les coupeurs, d’ajuster ou de changer des montages.

En dépannant, soyez sûr de fermer le commutateur de

début en position de « OFF ». Un démarrage accidentel

peut entraîner des blessures.

23. Mettre l’atelier à l’abri des enfants au moyen de

cadenas, d’interrupteurs principaux ou en enlevant

les boutons des dispositifs de mise en marche. Le

démarrage accidentel de la machine par un enfant ou un

visiteur peut entraîner des blessures.

24. Rester vigilant, attentif, et faire preuve de bon sens. Ne

pas utiliser la machine lorsque l’on est fatigué ou sous

l’influence de drogues, d’alcool ou de médicaments. Un

instant d’inattention lors de l’utilisation d’outils électriques

peut entraîner des blessures graves.

25.

L’utilisation de cet outil peut

produire et disperser de la poussière ou d’autres

particules en suspension dans l’air, telles que la

sciure de bois, la poussière de silicium cristallin et

la poussière d’amiante. Dirigez les particules loin du

visage et du corps. Faites toujours fonctionner l’outil

dans un espace bien ventilé et prévoyez l’évacuation

de la poussière. Utilisez un système de dépoussiérage

chaque fois que possible. L’exposition à la poussière peut

causer des problèmes de santé graves et permanents,

respiratoires ou autres, tels que la silicose (une maladie

pulmonaire grave) et le cancer, et même le décès de la

personne affectée. Évitez de respirer de la poussière et

de rester en contact prolongé avec celle-ci. En laissant

la poussière pénétrer dans vos yeux ou votre bouche,

ou en la laissant reposer sur votre peau, vous risquez

de promouvoir l’absorption de substances toxiques.

Portez toujours des dispositifs de protection respiratoire

homologués par niosh/osha, appropriés à l’exposition à

la poussière et de taille appropriée, et lavez à l’eau et au

savon les surfaces de votre corps qui ont été exposées.

1. NE PAS FAIRE FONCTIONNER CET APPAREIL avant qu’il

ne soit entièrement assemblé et installé conformément à ces

directives. Un appareil mal assemblé peut provoquer des

blessures graves.

2. DEMANDER CONSEIL à un superviseur, instructeur, ou toute

autre personne qualifiée si l’on ne maîtrise pas parfaitement

l’utilisation de cet appareil. La connaissance est synonyme de

sécurité.

3. SUIVRE TOUS LES CODES DE CÂBLAGE et les

branchements électriques recommandés afin d’éviter les

chocs électriques ou l’électrocution.

4. MAINTENIR LES COUTEAUX AIGUISÉS et exempts de

rouille et de résine. Les couteaux émoussés ou rouillés

fonctionnent moins bien et peuvent causer un effet de

rebond.

5. NE JAMAIS DÉMARRER LA MACHINE avant de débarrasser

la table de tout objet (outils, rognures de bois, etc.). La

projection de débris peut causer des blessures graves.

6. NE JAMAIS DÉMARRER LA MACHINE si la pièce est en

contact avec le couteau. Il y aurait danger d’effet de rebond.

7. FIXER LA MACHINE À UNE SURFACE D’APPUI pour

l’empêcher de glisser, de se déplacer ou de basculer.

8. BIEN FIXER LES COUTEAUX LOGÉS DANS LE PORTE-LAME

avant de mettre l’appareil en marche. Des lames desserrées

peuvent être projetées à une vitesse élevée et causer des

blessures graves.

9. Lors du rangement ou du transport de l’appareil, NE PAS

RANGER LE CORDON D’ALIMENTATION sous le porte-

lame.

10. ÉVITER LES OPÉRATIONS MALADROITES ET ÉVITER

D’AVOIR LES MAINS MAL PLACÉES. Un glissement soudain

de la pièce pourrait entraîner votre main vers les couteaux

11. TENIR LES BRAS, MAINS ET DOIGTS éloignés du porte-

lame, de l’orifice d’extraction des copeaux et des cylindres

d’entraînement pour éviter de profondes coupures.

12. SE TENIR LOIN DE LA ZONE DU PORTE-LAME lorsque la

machine fonctionne. Vos mains pourraient être entraînées dans

les couteaux.

13. NE PAS SE TENIR DANS LE MÊME AXE QUE LA PIÈCE. Un

effet de rebond peut causer des blessures.

14. LE PORTE-LAME DOIT ATTEINDRE SA VITESSE

MAXIMALE avant d’acheminer une pièce.

15. POUR LE RABOTAGE DE BOIS SPÉCIAL COURBÉ, placer

la partie concave de la pièce sur la table, et raboter dans le

sens du grain pour éviter tout effet de rebond.

16.

NE PAS ACHEMINER UNE PIÈCE qui est gauchie, qui présente

des nœuds ou qui comprend des objets étrangers (clous, agrafes,

etc.). Il y a risque d’effet de rebond.

17. NE PAS INSÉRER UNE PIÈCE DE FAIBLE LONGUEUR,

ÉPAISSEUR OU ÉTROITE DANS LA MACHINE. Vos mains

pourraient être entraînées sur les couteaux ou la pièce peut

être projetée à une vitesse élevée. Consulter la SECTION

« Utilisation » de ce mode d’emploi pour obtenir des détails.

18. NE PAS INSÉRER UNE PIÈCE par l’extrémité de sortie de la

machine. La pièce sera projetée du côté opposé à une vitesse

élevée.

19.

ENLEVER UNIQUEMENT LES FRISURES DE BOIS lorsque la

machine est éteinte pour éviter toute blessure grave.

20. UTILISATION PRÉVUE UNIQUEMENT POUR APLANIR LE

BOIS. Ne pas raboter des matières manufacturées.

21. SOUTENIR CORRECTEMENT LES PIÈCES LONGUES OU

LARGES. La perte de contrôle de la pièce peut provoquer de

graves blessures.

22. NE JAMAIS EFFECTUER D’OPÉRATION DE TRAÇAGE,

D’ASSEMBLAGE, ou de réglage sur la table/l’espace de

travail lorsque la machine est en marche. Cela risquerait

d’entraîner des blessures graves.

23. ÉTEINDRE LA MACHINE ET LA DÉBRANCHER. Nettoyer

la table/l’espace de travail avant de quitter la machine.

Afin d’éviter toute utilisation non autorisée, VERROUILLER

L’INTERRUPTEUR EN POSITION ARRÊT. Quelqu’un

pourrait par mégarde faire démarrer la machine et se blesser

ou blesser d’autres personnes.

24. DES INFORMATIONS SUPPLÉMENTAIRES (c.-à-d. une

vidéo sur la sécurité), sur la façon d’utiliser des outils électriques

correctement et en toute sécurité, sont offertes auprès du

Power Tool Institute, 1300 Sumner Avenue, Cleveland, OH

44115-2851, États-Unis (www.powertoolinstitute.com). Des

renseignements sont également offerts auprès du National

Safety Council, 1121 Spring Lake Drive, Itasca, IL, 60143-

3201 É.-U. Consulter les règles de sécurité de la norme ANSI

01,1 (American National Standards Institute) concernant les

machines à travailler le bois, ainsi que la réglementation du

département du Travail des É.-U.

RÈGLES SPÉCIFIQUES ADDITIONNELLES DE SÛRETÉ

L’inobservation de ces règles peut conduire à des blessures graves.

CONSERVER CES DIRECTIVES.

Les consulter souvent et les utiliserpour donner des directives aux autres.

RACCORDEMENTS ÉLECTRIQUES

Un circuit électrique séparé doit être utilisé pour les machines. Ce circuit doit utiliser un câble de calibre 12 au minimum et doit être protégé

par un fusible temporisé. REMARQUE : les fusibles temporisés devraient avoir l’inscription « D » au Canada et « T » aux É.-U. Si on utilise

un cordon prolongateur, ce cordon doit être à trois fils, avoir unefiche à trois broches et une prise de courant à trois cavités, mise à la terre

qui correspond à la fiche de la machine. Avant debrancher la machine, s’assurer que l’interrupteur se trouve en position « OFF » (ARRÊT)

et que le courantélectrique présente les mêmes caractéristiques que celles qui sont inscrites sur la machine. Toutes les connexions

électriquesdoivent établir un bon contact. Le fonctionnement sur une basse tension endommagera la machine.

Ne pas exposer la machine à la pluie, et ne pas l’utiliser dans des endroits humides.

INSTRUCTIONS DE MISE À LA TERRE

Cette machine doit être mise à la terre pendant son emploi, afin de protéger l’utilisateur des décharges électriques.

SPÉCIFICATIONS DU MOTEUR

Cette machine est câblée pour un fonctionnement sur un courant alternatif de 120 volts 60 Hz. Avant de brancher la machine, s’assurer que

l’interrupteur se trouve à la position « OFF » (ARRÊT).

BOÎTE À PRISES MISE À LA TERRE

BROCHES

CONDUCTRICES DE

COURANT

LA BROCHE DE MISE

À LA TERRE EST LA PLUS

LONGUE DES TROIS

OREILLE DE MISE À

LA TERRE

ADAPTATEUR

2. Machines avec cordon mis à la terre prévues pour une utilisation sur une alimentation nominale inférieure à 150 volts:

Si cette machine est prévue pour être utilisée sur un circuit qui comporte une prise semblable à celle illustrée à la figure A, la

machine devra comporter une fiche mise à la terre semblable à celle illustrée à la figure A. Un adaptateur temporaire semblable à

celui illustré à la figure B, peut être utilisé pour raccorder cette fiche à une prise à deux cavités comme celle illustrée à la figure B,

si une prise correctement mise à la terre n’est pas disponible. L’adaptateur temporaire ne doit être utilisé que jusqu’au moment

où une prise correctement mise à la terre est installée par un électricien compétent. L’oreille rigide ou autre dispositif semblable

de couleur verte, sur le dessus de l’adaptateur, doit être connecté sur une mise à la terre permanente comme, par exemple une

boîte à prises correctement mise à la terre. Quand un adaptateur est utilisé, celui-ci doit être retenu en place par une vis en

métal.

REMARQUE: Au Canada, le Code canadien de l’électriciténe permet pas l’emploi d’un adaptateur temporaire.

Dans tous les cas, s’assurer quela prise en question est bien mise à la terre. Dans le doute, demander à un

électricien compétent de vérifier la prise.

1. Toutes les machines avec cordon mis à la terre: Dans l’éventualité d’un mauvais fonctionnement ou d’une panne, la mise à

la terre fournit un trajet de moindre résistance permettant de réduire le risque de décharge électrique. Cette machine est dotée

d’un cordon électrique possédant un conducteur de mise à la terre de l’équipement ainsi que d’une fiche mise à la terre. La fiche

doit être branchée dans une prise de courant correspondante, installée de façon adéquate et mise à la terre conformément à

tous les codes et règlements locaux.

Ne pas modifier la fiche fournie – si elle ne s’adapte pas à la prise de courant, il faut faire installer une prise de courant

convenable par un électricien compétent.

Un mauvais raccordement du conducteur de mise à la terre de l’équipement peut entraîner un risque de décharge électrique. Le

conducteur possédant un isolant avec surface extérieure de couleur verte, avec ou sans rayures jaunes, est le conducteur de

mise à la terre de l’équipement. Si une réparation ou un remplacement du cordon électrique s’avère nécessaire, ne pas brancher

le conducteur de mise à la terre de l’équipement à une borne sous tension.

Consulter un électricien compétent ou le personnel de service après-vente si on ne comprend pas entièrement les instructions

de mise à la terre, ou si l’on doute que la machines oit correctement mise à la terre.

Utiliser seulement des cordons prolongateurs à trois fils dotés d’une fiche mise à la terre, à trois broches, et de prises à trois

cavités convenant à la fiche de la machine, comme l’illustre la figure A.

Réparer ou remplacer sans délai tout cordon endommagé ou usé.

Employez les cordes

appropriées de prolongation. S’assurent votre corde

de prolongation est en bon état. En utilisant une corde

de prolongation, soyez sûr d’employer un assez lourd

pour porter le courant de la machine. Une corde trop

petite causera une baisse dans la tension secteur, ayant

pour résultat la perte de puissance et de surchauffe.

Fig. C expositions la mesure correcte à employer

selon la longueur de corde. En cas de doute, utilisez

la prochaine mesure plus lourde. Plus le nombre de

mesure est petit, plus la corde est lourde.

MESUR MINIMUM DE CORDE D’EXTENSION

TAILLES RECOMMANDÉES POUR L’USAGE AVEC STATIONNAIRES ÉLECTRIQUES LES OUTILS

Estimation

ampère Volts

Longueur

totale de

corde en

pieds

Mesure de corde d’am

d’extension

0-6 120

jusqu’à

25 18 AWG

0-6 120 25-50 16 AWG

0-6 120 50-100 16 AWG

0-6 120 100-150 14 AWG

6-10 120

jusqu’à

25 18 AWG

6-10 120 25-50 16 AWG

6-10 120 50-100 14 AWG

6-10 120 100-150 12 AWG

10-12 120

jusqu’à

25 16 AWG

10-12 120 25-50 16 AWG

10-12 120 50-100 14 AWG

10-12 120 100-150 12 AWG

12-16 120

jusqu’à

25 14 AWG

12-16 120 25-50 12 AWG

12-16 120

50 PI PLUS GRANDS QUE NON RECOMMANDES

Fig. A

Fig. B

CORDON DE RALLONGE

Fig. C

La page charge ...

Delta 22-590X Manuel utilisateur

Marque: Delta

Modèle: 22-590X

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Delta 22-590X User manual
español: Delta 22-590X Manual de usuario

Delta 22-590X Manuel utilisateur

Ce manuel convient également à

Delta 22-590X Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents