Zanussi ZCG664GW Manuel utilisateur

Marque: Zanussi

Modèle: ZCG664GW

Catégorie: Cuisinières

Taper: Manuel utilisateur

Ce manuel convient également à

ZCG664GX

User manual 2

Notice d'utilisation 22

Cooker

Cuisinière

ZCG664G

Contents

Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2

Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ 3

Product description _ _ _ _ _ _ _ _ _ _ _ _ _ 6

Before first use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7

Hob - Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7

Hob - Helpful hints and tips _ _ _ _ _ _ _ _ _ 8

Hob - Care and cleaning _ _ _ _ _ _ _ _ _ _ _ 8

Oven - Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9

Oven - Using the accessories _ _ _ _ _ _ _ 11

Oven - Helpful hints and tips _ _ _ _ _ _ _ _ 12

Oven - Care and cleaning _ _ _ _ _ _ _ _ _ 14

What to do if… _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 16

Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 17

Environment concerns _ _ _ _ _ _ _ _ _ _ _ 21

Subject to change without notice.

Safety information

Before the installation and use of the appliance, carefully read the

supplied instructions. The manufacturer is not responsible if an in-

correct installation and use causes injuries and damages. Always

keep the instructions with the appliance for future reference.

Children and vulnerable people safety

Warning! Risk of suffocation, injury or permanent disability.

• This appliance can be used by children aged from 8 years and

above and persons with reduced physical, sensory or mental ca-

pabilities or lack of experience and knowledge if they are super-

vised by an adult or a person who is responsible for their safety.

• Do not let children play with the appliance.

• Keep all packaging away from children.

• Keep children and pets away from the appliance when it operates

or when it cools down. Accessible parts are hot.

• If the appliance has a child safety device, we recommend that you

activate it.

• Cleaning and user maintenance shall not be made by children

without supervision.

General Safety

• The appliance and its accessible parts become hot during use.

Do not touch the heating elements.

www.zanussi.com

• Do not operate the appliance by means of an external timer or

separate remote-control system.

• Unattended cooking on a hob with fat or oil can be dangerous

and may result in fire.

• Never try to extinguish a fire with water, but switch off the appli-

ance and then cover flame e.g. with a lid or a fire blanket.

• Do not store items on the cooking surfaces.

• Do not use a steam cleaner to clean the appliance.

• Metallic objects such as knives, forks, spoons and lids should not

be placed on the hob surface since they can get hot.

• Remove any spillage from the lid before opening. Let the hob sur-

face cool down before closing the lid.

• Do not use harsh abrasive cleaners or sharp metal scrapers to

clean the glass door since they can scratch the surface, which

may result in shattering of the glass.

Safety instructions

Installation

Warning! Only a qualified person must

install this appliance.

• Remove all the packaging.

• Do not install or use a damaged appliance.

• Obey the installation instruction supplied

with the appliance.

• Always be careful when you move the appli-

ance because it is heavy. Always wear safety

gloves.

• Do not pull the appliance by the handle.

• Keep the minimum distance from the other

appliances and units.

• Make sure that the appliance is installed be-

low and adjacent safe structures.

• The sides of the appliance must stay adja-

cent to appliances or to units with the same

height.

• Do not install the appliance on a platform.

• Do not install the appliance adjacent to a

door or under a window. This prevents hot

cookware to fall from the appliance when the

door or the window is opened.

Electrical connection

Warning! Risk of fire and electrical shock.

• All electrical connections should be made by

a qualified electrician.

• The appliance must be earthed.

• Make sure that the electrical information on

the rating plate agrees with the power sup-

ply. If not, contact an electrician.

• Always use a correctly installed shockproof

socket.

• Do not use multi-plug adapters and exten-

sion cables.

• Make sure not to cause damage to the mains

plug and to the mains cable. Contact the

Service or an electrician to change a dam-

aged mains cable.

www.zanussi.com

• Do not let mains cables to come in touch

with the appliance door, specially when the

door is hot.

• The shock protection of live and insulated

parts must be fastened in such a way that it

cannot be removed without tools.

• Connect the mains plug to the mains socket

only at the end of the installation. Make sure

that there is access to the mains plug after

the installation.

• If the mains socket is loose, do not connect

the mains plug.

• Do not pull the mains cable to disconnect

the appliance. Always pull the mains plug.

• Use only correct isolation devices: line pro-

tecting cut-outs, fuses (screw type fuses re-

moved from the holder), earth leakage trips

and contactors.

• The electrical installation must have an isola-

tion device which lets you disconnect the ap-

pliance from the mains at all poles. The isola-

tion device must have a contact opening

width of minimum 3 mm.

Gas connection

• All gas connections should be made by a

qualified person.

• Make sure that there is air circulation around

the appliance.

• The information about the gas supply is on

the rating plate.

• This appliance is not connected to a device,

which evacuates the products of combus-

tion. Make sure to connect the appliance ac-

cording to current installation regulations.

Pay attention to requirements regarding ade-

quate ventilation.

Use

Warning! Risk of injury, burns or electric

shock.

• Use this appliance in a household environ-

ment.

• Do not change the specification of this appli-

ance.

• Make sure that the ventilation openings are

not blocked.

• Do not let the appliance stay unattended

during operation.

• Deactivate the appliance after each use.

• Internally the appliance becomes hot when in

operation. Do not touch the heating elements

that are in the appliance. Always use oven

gloves to remove or put in oven accessories

or ovenware.

• Be careful, when you open the appliance

door while the appliance is in operation. Hot

air can release.

• Do not operate the appliance with wet hands

or when it has contact with water.

• Do not apply pressure on the open door.

• Always keep the appliance door closed when

the appliance is in operation.

• Do not put cutlery or saucepan lids on the

cooking zones. They become hot.

• Set the cooking zone to “off” after use.

• Do not use the appliance as a work surface

or as a storage surface.

• Provide good ventilation in the room where

the appliance is installed.

• Use only stable cookware with the correct

shape and diameter larger than the dimen-

sions of the burners.

• Make sure the flame does not go out when

you quickly turn the knob from the maximum

to the minimum position.

• Make sure pots are centrally positioned on

the rings and do not stick out over edges of

the cooking surface.

• Use only the accessories supplied with the

appliance.

• Do not install a flame diffuser on the burner.

Warning! Risk of fire or explosion.

• Fats and oil when heated can release flam-

mable vapours. Keep flames or heated ob-

jects away from fats and oils when you cook

with them.

• The vapours that very hot oil releases can

cause spontaneous combustion.

www.zanussi.com

• Used oil, that can contain food remnants, can

cause fire at a lower temperature than oil

used for the first time.

• Do not put flammable products or items that

are wet with flammable products in, near or

on the appliance.

• Do not let sparks or open flames to come in

contact with the appliance when you open

the door.

• Open the appliance door carefully. The use

of ingredients with alcohol can cause a mix-

ture of alcohol and air.

Warning! Risk of damage to the

appliance.

• To prevent damage or discoloration to the

enamel:

– Do not put ovenware or other objects in

the appliance directly on the bottom.

– Do not put aluminium foil directly on the

bottom of the appliance.

– do not put water directly into the hot appli-

ance.

– do not keep moist dishes and food in the

appliance after you finish the cooking.

– be careful when you remove or install the

accessories.

• Discoloration of the enamel has no effect on

the performance of the appliance. It is not a

defect in the sense of the warranty law.

• Use a deep baking tray for moist cakes. Fruit

juices cause stains that can be permanent.

• Do not keep hot cookware on the control

panel.

• Do not let cookware to boil dry.

• Be careful not to let objects or cookware fall

on the appliance. The surface can be dam-

aged.

• Do not activate the cooking zones with emp-

ty cookware or without cookware.

• Do not put aluminium foil on the appliance.

• Cookware made of cast iron, aluminium or

with a damaged bottom can cause scratches

on the glass ceramic. Always lift these ob-

jects up when you have to move them on the

cooking surface.

Lid

• Do not change the specification of the lid.

• Clean the lid regularly.

• Do not open the lid, when there are spills on

the surface.

• Before you close the lid turn all burners off.

• Do not close the lid until the hob and oven

are completely cold.

• Glass lids can shatter, when heated (if appli-

cable).

Gas Grill

Warning! Risk of fire and burns.

• Do not put the oven shelf with food on the

highest shelf level.

Care and Cleaning

Warning! Risk of injury, fire or damage to

the appliance.

• Before maintenance, deactivate the appli-

ance and disconnect the mains plug from the

mains socket.

• Make sure the appliance is cold. There is the

risk that the glass panels can break.

• Replace immediately the door glass panels

when they are damaged. Contact the Serv-

ice.

• Be careful when you remove the door from

the appliance. The door is heavy!

• Clean regularly the appliance to prevent the

deterioration of the surface material.

• Remaining fat or food in the appliance can

cause fire.

• Clean the appliance with a moist soft cloth.

Only use neutral detergents. Do not use

abrasive products, abrasive cleaning pads,

solvents or metal objects.

www.zanussi.com

• If you use an oven spray, obey the safety in-

structions on the packaging.

• Do not clean the catalytic enamel (if applica-

ble) with any kind of detergent.

• Do not clean the burners in the dishwasher.

Internal light

• The type of light bulb or halogen lamp used

for this appliance, is only for household appli-

ances. Do not use it for house lighting.

Warning! Risk of electrical shock.

• Before replacing the lamp, disconnect the

appliance from the power supply.

• Only use lamps with the same specifications.

Disposal

Warning! Risk of injury or suffocation.

• Disconnect the appliance from the mains

supply.

• Cut off the mains cable and discard it.

• Remove the door catch to prevent children

and pets to get closed in the appliance.

Service

• Contact the Service to repair the appliance.

We recommend only the use of original

spare parts.

Product description

General overview

1 32 54

Control panel

Spark generator button

Knobs for the hob

Knob for the Minute Minder

Knob for the oven functions

Button for the oven lamp and turnspit

Grill

Oven lamp

Turnspit hole

Rating plate

Shelf levels

www.zanussi.com

Cooking surface layout

Semi-rapid burner

Auxiliary burner

Rapid burner

Accessories

• Oven shelf

For cookware, cake tins, roasts.

• Flat baking tray

For cakes and biscuits.

• Flat aluminized baking tray

For cakes and biscuits.

• Turnspit

For roasting larger joints of meat and poultry.

• Grill deflector

To protect the knobs when you use the grill.

• Storage compartment

Below the oven is the storage compartment.

To use the compartment, lift the lower front

door then pull down.

Warning! The storage compartment can

become hot when the appliance operates.

Before first use

Warning! Refer to the Safety chapters.

Caution! To open the oven door, always

hold the handle in the centre.

Initial Cleaning

• Remove all parts from the appliance.

• Clean the appliance before first use.

Caution! Do not use abrasive cleaning

agents! This can damage the surface.

Refer to chapter "Care and Cleaning".

Preheating

Set an oven to maximum temperature and run

an empty oven for 45 minutes, to burn off any

residue from the cavity surface. Accessories

can become hotter than in normal use. During

this period an odour can be emitted. This is

normal. Make sure the room is well ventilated.

Hob - Daily use

Warning! Refer to the Safety chapters.

Ignition of the burner

Warning! Be very careful when you use

open fire in kitchen environment.

Manufacturers decline any responsibility in case

of misuse of the flame.

www.zanussi.com

Always light the burner before you put the

cookware on it.

To light the burner:

1. Push and hold the spark generator button

2. Turn the control knob counterclockwise to

the maximum position

. Push the knob in

and hold.

3. Release the spark generator button but

keep the control knob on this position for

approximately 10 seconds; this will let ther-

mocouple to warm up. If not, the gas sup-

ply will be interrupted.

4. Adjust the flame after it is regular.

If after some tries the burner does not

light, check if the crown and its cap are in

correct positions.

Burner cap

Burner crown

Ignition candle

Thermocouple

Warning! If the burner does not light after

10 seconds, release the control knob, turn

it into off position and try to light the burner

again after minimum 1 minute.

Important! You can light the burner without

electrical device (e.g. when there is no

electricity in the kitchen). To do so, put the

flame near the burner, turn the related knob to

the maximum gas release position and push it

down for 10 seconds.

If the burner accidentally goes out, turn the

control knob to the off position and try to

light the burner again after minimum 1 minute.

The spark generator can start automatical-

ly when you switch on the mains, after in-

stallation or a power cut. It is normal.

Turning the burner off

To put the flame out, turn the knob to the sym-

bol

Warning! Always turn the flame down or

switch it off before you remove the pans

from the burner.

Hob - Helpful hints and tips

Energy savings

• If possible, always put the lids on the pans.

• When the liquid starts to boil, turn down the

flame to barely simmer the liquid.

Warning! Use pots and pans with bottom

applicable to the dimension of burner.

Do not use cooking vessels on the hotplate that

overlap its edges.

Burner Diameters of cookware

Rapid 160 - 260 mm

Semi-rapid 140 - 240 mm

Auxiliary 120 - 180 mm

Use cookware with the bottom as thick and flat

as possible.

Hob - Care and cleaning

Warning! Refer to the Safety chapters.

www.zanussi.com

Warning! Switch the appliance off and let

it cool down before you clean it.

Warning! For safety reasons, do not clean

the appliance with steam cleaners or high-

pressure cleaners.

Warning! Do not use abrasive cleaners,

steel wool pads or acids, they can cause

damage to the appliance.

• To clean the enamelled parts, cap and

crown, wash it with warm soapy water.

• Stainless steel parts wash with water, and

then dry with a soft cloth.

• The pan supports are not dishwasher proof;

they must be washed by hand.

• Make sure you position the pan supports

correctly after cleaning.

• To make burners work correctly, make sure

that the arms of the pan supports are in the

centre of the burner.

• Be very careful when you replace the

pan supports to prevent the hob top

from damage.

After cleaning, dry the appliance with a soft

cloth.

Oven - Daily use

Warning! Refer to the Safety chapters.

Oven Functions

Oven function Application

Off position To switch off the appliance.

1 - 8

Range of tempera-

ture levels adjust-

ment

Range of temperature levels adjustment for conventional cooking. (1 - 135

°C; 2 - 150 °C; 3 - 165 °C; 4 - 180 °C; 5 - 195 °C; 6 - 210 °C; 7 - 230

°C; 8 - 250 °C)

Pizza setting To make pizza.

Grill

To grill flat food in the middle of the grill. To make toast.

Warning! Maximum temperature for this function is 210 °C.

Oven lamp

To light up the oven interior without any cooking function. To use this func-

tion, button for oven lamp and turnspit.

Turnspit

To spit roasting meat. To use this function, press the button for oven lamp

and turnspit.

Gas oven cooking

Ignition of oven gas burner:

1. Open the oven door.

2. Push and hold the spark generator button (

3. Turn the gas oven control knob counter-

clockwise to the maximum position. Push

the knob in and hold. Release the spark

generator button but keep the gas oven

control knob on this position for approxi-

mately 10 seconds. Do not release it until

the flame comes on.

4. Turn the gas oven control knob to the nec-

essary temperature setting.

www.zanussi.com

If the oven gas burner does not come on

or if it accidentally goes out:

1. Release the gas oven control knob and

turn it to the Off position

2. Open the oven door.

3. After one minute, try to light the oven gas

burner again.

Manual ignition:

If there is no power supply, temporarily.

1. Open the oven door.

2. Hold a flame near the hole in the bottom of

the oven cavity.

3. At the same time turn the gas oven control

knob counterclockwise to the maximum

temperature.

4. When the flame comes on, keep the gas

oven control knob on the maximum position

for approximately 10 seconds.

5. Turn the gas oven control knob to the nec-

essary temperature setting.

Control the flame through the holes in the

bottom of the oven.

Oven safety device:

The gas oven has a thermocouple. It stops the

gas flow, if the flame goes out.

Turning off the oven burner

To put out the flame, turn the knob to the off

position.

Using the grill

Warning! Do not leave the appliance

unattended during grilling. The accessible

parts of the appliance become hot. There is a

risk of burns.

Warning! Keep children away when the

grill operates. There is a risk of burns.

Warning! Never use the grill with closed

door. There is a risk of fire or carbon

monoxide emissions.

1. Open the appliance door.

2. Put grill deflector A into position above the

door. Make sure that the two catches en-

gage correctly in the holes in the top part

of the front frame of the oven cavity (under-

neath the control panel).

3. Push and hold the spark generator button.

4. Turn the oven control knob to the Grill po-

sition

. Push the knob in and hold.

Caution! Make sure to turn the knob as

far as it goes, avoiding the intermediary

position between Off and Grill. On intermediary

positions the spark generator can remain active.

5. Release the spark generator button.

6. Keep the oven control knob in this position

for approximately 15 seconds. Do not re-

lease it until the flame comes on.

7. Release the oven control knob.

8. Preheat the grill for 5 to 10 minutes.

9. Put the meat on the oven shelf and put it

on shelf level 3.

Warning! Do not put the meat on the

highest shelf level. There is a risk of fire.

10. Put a baking tray or roasting pan below, on

shelf level 2, to collect the juices.

Do not put the meat directly in the tray or

pan.

11. Keep the oven door slightly open.

www.zanussi.com

12. When the first side is roasted, turn the

meat over with a fork to avoid losing its

juice.

13. When the second side is also ready, re-

move the meat from the oven.

If the grill does not come on or accidental-

ly goes out:

1. Release the gas oven control knob and

turn it to the Off position.

2. Open the appliance door.

3. After one minute, try to light the grill again.

Manual ignition:

If there is no power:

1. Open the appliance door.

2. Hold a flame near the burner of the grill.

Turn the oven control knob to

. Push

the knob in and hold.

Turning off the grill burner

To put out the flame, turn the knob to the off

position.

Timer - Minute Minder

Use it to set a countdown time.

First turn the knob for the timer (refer to "Prod-

uct description") clockwise as far as it goes.

Then turn it counterclockwise to the necessary

time period value. A signal sounds after the

time period ends.

This function has no effect on the opera-

tion of the oven.

Oven - Using the accessories

Warning! Refer to the Safety chapters.

Inserting the baking tray

Put the tray in the centre of the oven cavity, be-

tween the front and rear wall. This ensures that

the heat can circulate in front of and behind the

baking tray. Make sure that the tray is posi-

tioned like in the picture, with the angled slope

in the rear.

Warning! Do not push the baking tray all

the way to the rear wall of the oven cavity.

This prevents the heat from circulating around

the tray. The food may be burnt, especially in

the rear part of the tray.

Turnspit

Warning! Be careful when you use the

turnspit. The forks and the spit are sharp.

There is a risk of injury.

Warning! Use oven gloves when you

remove the turnspit. The turnspit and the

grill are hot. There is a risk of burns.

1. Open the oven door.

2. Put the support hook in the indentation in

the top of the front frame of the oven.

3. Install the first fork on the spit, then put the

meat on the turnspit and install the second

fork. Make sure that the meat is in the mid-

dle of the spit.

4. Tighten the forks.

5. Put the tip of the spit in the turnspit hole.

Refer to "Product description".

www.zanussi.com

6. Put the front part of the spit on the support

hook.

7. Remove the turnspit handle.

8. Put the roasting pan on the lowest shelf

level.

9. Light the grill burner. Refer to "Using the

grill".

10.

Press the Turnspit button

. Make sure

that the turnspit rotates.

11. After the meat is roasted, turn the knob to

the Off position.

12. Install the turnspit handle.

13. Carefully remove the turnspit and the

roasting pan from the oven.

The maximum weight permitted on the

turnspit is 4-5 kg.

Oven - Helpful hints and tips

Caution! Use a deep baking tray for very

moist cakes. Fruit juices can cause

permanent stains on the enamel.

• The appliance has four shelf levels. Count

the shelf levels from the bottom of the appli-

ance floor.

• Moisture can condense in the appliance or

on the glass doors. This is normal. Always

stand back form the appliance when you

open the appliance door while cooking. To

decrease the condensation, run the appli-

ance for 10 minutes before cooking.

• Wipe away moisture after every use of the

appliance.

• Do not put the objects directly on the appli-

ance floor and do not cover the components

with aluminium foil when you cook. This can

change the baking results and damage the

enamel coating.

Baking cakes

• Preheat the oven for approximately 10 mi-

nutes before baking.

• Do not open the oven door before 3/4 of the

set cooking time is up.

Cooking meat and fish

• Do not cook meat with weight below 1 kg.

Cooking too small quantities makes the meat

too dry.

• Use a dripping pan for very fatty food to pre-

vent the oven from stains that can be perma-

nent.

• Leave the meat for approximately 15 minutes

before carving so that the juice does not

seep out.

• To prevent too much smoke in the oven dur-

ing roasting, add some water into the drip-

ping pan. To prevent the smoke condensa-

tion, add water each time after it dries up.

Cooking times

Cooking times depend on the type of food, its

consistency, and volume.

Initially, monitor the performance when you

cook. Find the best settings (heat setting, cook-

ing time, etc.) for your cookware, recipes and

quantities when you use this appliance.

www.zanussi.com

Cooking table

Food Tray type and shelf level

Preheating

time (mi-

nutes)

Ther-

mostat

posi-

tion

Cooking /

baking time

(minutes)

Pastry stripes (250 g) aluminized tray at level 3 10 2 25 - 30

Pastry stripes (250 g) enamelled tray at level 3 10 2 20 - 25

Flat cake (1000 g) aluminized / enamelled tray at

level 3

10 2 - 3 35 - 40

Yeast cake with apples (2000

aluminized tray at level 3 10 5 50 - 60

Apple pie (1200 + 1200 g) 2 round aluminized trays (di-

ameter: 20 cm) at level 3

10 6 55 - 65

Small cakes (500 g) aluminized tray at level 3 10 2 - 3 25- 30

Fatless sponge cake (350 g) 1 round tray (diameter: 26

cm) at level 3

10 3 30 - 35

Drip pan cake (1500 g) aluminized / enamelled tray at

level 3

- 2 - 3

45 - 55

Chicken, whole (1400 g)

oven shelf at level 3

- 8 50 - 60

Flan bread ( 800 g) aluminized / enamelled tray at

level 3

20 7 15 - 20

Stuffed yeast cake (1200 g) aluminized / enamelled tray at

level 3

15 4 - 5 40 - 50

Pizza (1000 g) aluminized / enamelled tray at

level 3

10 5 - 6 25 - 35

Cheese cake (2600 g) aluminized / enamelled tray at

level 3

- 2 70 - 90

Swiss apple flan (1900 g) aluminized / enamelled tray at

level 3

15 6 - 7 40 - 60

Christmas cake (2400 g) aluminized / enamelled tray at

level 3

3 - 4

Quiche Lorraine (1000 g) 1 round tray (diameter: 26

cm) at level 3

15 5 - 6 50 - 60

Peasant bread (750 + 750 g) 2 round aluminized trays (di-

ameter: 20 cm) at level 3

4 - 5 50 - 60

Romanian sponge cake (600 +

600 g)

2 round aluminized trays (di-

ameter: 25 cm) at level 3

10 2 - 3 50 - 60

Romanian sponge cake - tradi-

tional (600 + 600 g)

2 round aluminized trays (di-

ameter: 25 cm) at level 3

10 2 - 3 40 - 50

Swiss roll (500 g) aluminized / enamelled tray at

level 3

10 2 - 3 20 - 30

Meringue (400 g) aluminized / enamelled tray at

level 3

- 1 - 2 40 - 50

www.zanussi.com

Food Tray type and shelf level

Preheating

time (mi-

nutes)

Ther-

mostat

posi-

tion

Cooking /

baking time

(minutes)

Petit Choux (500 g) aluminized / enamelled tray at

level 3

10 3 - 4 30 - 40

Crumble cake (1500 g) aluminized / enamelled tray at

level 3

15 5 - 6 30 - 40

Sponge cake (600 g) aluminized / enamelled tray at

level 3

10 2 35 - 40

Buttered cake (600 g) aluminized / enamelled tray at

level 3

15 3 20 - 30

1) After you switch off the appliance, leave the cake in the oven for 5 - 7 minutes.

2) Put a baking tray under the oven shelf, on shelf level 2.

3) Thermostat at position: 8

4) After you switch off the appliance, leave the cake in the oven for 5 - 10 minutes.

When you cook pizza, for best results turn

the knob for the oven functions to the Piz-

za position.

Grill with turnspit

Food Shelf level Cooking / baking time (minutes)

Chicken, whole (1000 g)

Oven shelf at level 3

1) Put a baking tray under the oven shelf, on shelf level 1.

Oven - Care and cleaning

Warning! Refer to the Safety chapters.

• Clean the front of the appliance with a soft

cloth with warm water and cleaning agent.

• To clean metal surfaces use a usual cleaning

agent

• Clean the oven interior after each use. Thus

you can remove dirt more easily and it does

not burn on.

• Clean stubborn dirt with a special oven

cleaner.

• Clean all oven accessories (with a soft cloth

with warm water and cleaning agent) after

each use and let them dry.

• If you have nonstick accessories, do not

clean them using an aggressive agents,

sharp edged objects or dishwasher. It can

destroy nonstick coating!

Cleaning the oven door

The oven door has two panels of glass installed

one behind the other. To make the cleaning

easier remove the oven door.

Warning! The oven door can close if you

try to remove the internal panel of glass

when the door is still assembled.

Warning! Make sure that the glass panels

are cool, before you clean the door. There

is the risk that the glass breaks.

www.zanussi.com

Warning! When the door glass panels are

damaged or have scratches, the glass

becomes weak and can break. To prevent this

you must replace them. For more instructions,

contact your local Service Centre.

Removing the oven door and the glass

panel

Open the door

fully and hold the two

door hinges.

Lift and turn the

levers on the two

hinges.

Close the oven

door to the first open-

ing position (halfway).

Then pull forward and

remove it from its

seat.

Place the door on

a stable surface pro-

tected by a soft cloth.

Use a screwdriver to

remove 2 screws

from the bottom edge

of the door.

Important! Do not

lose the screws.

Use a spatula

made of wood or

plastic or equivalent

to open the inner

door.

Hold the outer door,

and push the inner

door against the top

edge of the door.

Lift the inner door.

Clean inner side

of the door.

Clean the glass panel

with water and soap.

Dry it carefully.

Warning! Only clean the glass panel with

water and a soap. Abrasive cleaning

agents, stain removers and sharp objects (e.g.

knives or scrapers) can cause damage to the

glass.

Inserting the door and the glass panel

When the cleaning procedure is completed, in-

sert the oven door. To do so, do the steps in

opposite way.

Oven lamp

Warning! Be careful when you change

the oven lamp. Always switch off the

appliance before you start to replace the lamp.

There is a risk of electric shock.

www.zanussi.com

Warning! Bulb lamps used in this

appliance are special lamps for use only in

household appliances. Do not use them to

illuminate household rooms or parts of rooms. If

you need to replace a lamp, the replacement

lamp must have the same power and be for use

only in household appliances.

Before you change the oven lamp:

• Deactivate the appliance.

• Remove the fuses in the fuse box or deacti-

vate the circuit breaker.

• Put a cloth on the bottom of the oven. This

prevents from damage to the oven light and

glass cover.

Replacing the oven lamp:

1. Find the lamp glass cover at the back of

the cavity.

Turn the lamp glass cover counterclock-

wise to remove it.

2. Clean the glass cover.

3. Replace the oven lamp with an applicable

300 °C heat-resistant oven lamp.

Use only the same oven lamp type as the

replacement lamp. It must have the same

power and be for use only in household

appliances.

4. Install the glass cover.

What to do if…

Problem Possible cause Remedy

There is no spark when light-

ing the gas

There is no electrical supply Make sure that the unit is connected and the

electrical supply is switched on.

There is no spark when light-

ing the gas

There is no electrical supply Examine the house electrical installation

fuse.

There is no spark when light-

ing the gas

Burner cap and crown are

placed uneven

Make sure that the burner cap and crown

are in correct positions.

The flame is blow out immedi-

ately after ignition

Thermocouple is not heated

sufficient

After lightning the flame, keep the knob

pushed for approximately 5 seconds.

The gas ring burns unevenly Burner crown is blocked with

food residues

Make sure that the injector is not blocked

and the burner crown is clear of food parti-

cles.

The appliance does not oper-

ate

The fuse in the fuse box is

released

Control the fuse. If the fuse is released more

than one time, refer to a qualified electrician.

The oven does not heat up The oven is not switched on Switch on the oven.

The oven does not heat up The necessary settings are

not set

Control the settings.

The oven lamp does not op-

erate

The oven lamp is defective Replace the oven lamp.

Steam and condensation set-

tle on the food and in the

oven cavity

You left the dish in the oven

for too long

Do not leave the dishes in the oven for lon-

ger than 15 - 20 minutes after the cooking

process ends.

If you cannot find a solution to the problem

yourself, contact your dealer or the service cen-

tre.

The necessary data for the service centre is on

the rating plate. The rating plate is on the front

frame of the oven cavity.

We recommend that you write the data here:

www.zanussi.com

Model (MOD.) .........................................

Product number (PNC) .........................................

Serial number (S.N.) .........................................

Installation

Warning! Refer to the Safety chapters.

Location of the appliance

Minimal distances

Dimension mm

A 690

B 150

C 20

Technical Data

Dimensions

Height 855 mm

Width 600 mm

Depth 600 mm

Total electricity power 20,6 W

Voltage 230 V

Frequency 50 Hz

Gas Category II2H3B/P

Gas Supply G20 (2H) 13 mbar

G20 (2H) 20 mbar

G30/31 (3B/P) - 30/30

mbar

By-pass diameters

Burner Ø By-pass in 1/100

mm.

Auxiliary 29

Semi-rapid 32

Rapid 42

Oven 44

Gas burners

Burner Normal

power

Reduced

power

Type of gas Pressure Injector di-

ameter

Usage

kW kW mbar mm g/h

Auxiliary

burner

1,00 0,40 Natural Gas G20 13 0,82 -

1,00 0,35 Natural Gas G20 20 0,70 -

1,00 0,35 Butane G30 28 - 30 0,50 72,71

0,85 0,31 Propane G31 28 - 30 0,50 60,70

www.zanussi.com

Burner Normal

power

Reduced

power

Type of gas Pressure Injector di-

ameter

Usage

kW kW mbar mm g/h

Semi-rapid

burner

2,00 0,50 Natural Gas G20 13 1,11 -

2,00 0,43 Natural Gas G20 20 0,96 -

2,00 0,43 Butane G30 28 - 30 0,71 145,43

1,70 0,38 Propane G31 28 - 30 0,71 121,40

Rapid burn-

3,00 0,78 Natural Gas G20 13 1,32 -

3,00 0,72 Natural Gas G20 20 1,19 -

3,00 0,72 Butane G30 28 - 30 0,88 218,14

2,60 0,63 Propane G31 28 - 30 0,88 185,68

Oven 2,70 0,90 Natural Gas G20 13 1,30 -

2,70 0,90 Natural Gas G20 20 1,20 -

2,70 0,90 Butane G30 28 - 30 0,80 196,33

2,35 0,78 Propane G31 28 - 30 0,80 167,82

Grill 1,90 - Natural Gas G20 13 1,15 -

1,90 - Natural Gas G20 20 1,08 -

1,90 - Butane G30 28 - 30 0,71 138,16

1,65 - Propane G31 28 - 30 0,71 117,83

Gas Connection

Choose fixed connections or use a flexible pipe

in stainless steel in compliance with the regula-

tion in force. If you use flexible metallic pipes,

be careful they do not come in touch with mo-

bile parts or they are not squeezed.

Flexible nonmetal pipes connection

If it is possible to easily and fully control the gas

connection, you can use a flexible pipe. You

must tightly attach the flexible pipe by clamps.

To install, use a pipe holder. Make sure that you

tightly attach the pipe holder to the gasket, and

then continue with the gas connection. The

flexible pipe is correct when:

– It cannot become hotter than room tempera-

ture or higher than 30 °C.

– It is no longer than 1500 mm.

– It does not compress.

– It is not subject to traction or torsion.

– It does not make contact with sharp edges or

corners.

– You can easily examine it in order to check

its condition.

To preserve the flexible pipe, you must regularly

check if:

– It does not show cracks, cuts or burn marks

on the two ends and its length.

– The material is correctly elastic and not hard-

ened.

– The fastening clamps are not rusted.

– It is not expired.

If you can see one or more defects, do not re-

pair the pipe, but replace it.

Important! After installation is complete, use a

soapy solution and never a flame to see if you

sealed all the pipe fittings perfectly.

The gas supply ramp is on the rear side of the

control panel.

www.zanussi.com

Warning! Before gas connection

disconnect the mains plug from the

mains socket or switch off the fuse in the

fuse box. Close the primary valve of the

gas supply.

ABC

A) Gas connection point (only one point is ap-

plicable for appliance)

B) Gasket

C) Adjustable connection

D) LPG pipe holder

E) Natural Gas pipe holder

The appliance is set to default gas, to

change the setting choose pipe holder

from the list. Always use the gasket sealing.

Adjustment to different types of gas

Warning! Let only an authorized person

do the adjustment to different types of gas.

This appliance is for operation with natural

gas.

With the correct injectors, you can also operate

it with liquid gas.

Warning! Before replacing the injectors,

make sure that the gas knobs are in the

Off position and disconnect the appliance from

the electrical supply. Let the appliance cool off

fully. There is a risk of injury.

Injectors replacement

Replace the nozzles when changing the gas

type.

1. Remove the pan supports.

2. Remove the caps and crowns of the burn-

er.

3. With a socket spanner 7 remove the injec-

tors and replace them with the ones which

are necessary for the type of gas you use.

4. To assemble the parts, do the same steps

in reverse.

5. Replace the rating label (it is near the gas

supply pipe) with the one for the new type

of gas supply. You can find this label in the

package supplied with the appliance.

If the supply gas pressure is changeable or dif-

ferent from the necessary pressure, you must fit

an applicable pressure adjuster on the gas sup-

ply pipe.

Adjustment of minimum level

To adjust the minimum level of the burners:

1. Light the burner.

2. Turn the knob on the minimum position.

3. Remove the knob.

4. With a thin screwdriver, adjust the by-pass

screw position (A).

• If you change from natural gas to liquid gas,

fully tighten the adjustment screw in.

• If you change from liquid gas to natural gas,

undo the by-pass screw approximately 1/4 of

a turn.

Warning! Make sure the flame does not

go out when you quickly turn the knob

from the maximum position to the minimum

position.

www.zanussi.com

Oven injector replacement

1. Remove the bottom plate of the oven cavity

(A) to get access to the oven burner (B).

2. Release the screw (C), which keep the

burner in position.

3. Carefully move the burner off the injector

support (D).

Slowly move it to the left side. Make sure

that the burner bush stays on the burner

mouthpiece. Do not apply force to the wire

of the spark plug connector (E) and to the

thermocouple conductor (F), if applicable.

4. Release the burner injector (D) with a 7

mm socket spanner and remove it. Replace

it with the necessary one.

5. Assemble the burner in the opposite se-

quence.

6. Replace the gas type sticker near the gas

supply ramp with the one related to the

new gas type.

Replacing the grill burner injector:

1. Release the screw which keep the grill

burner in position.

2. Release the burner injector with a 7 mm

socket spanner and remove it. Replace it

with the necessary one.

3. Assemble the burner in opposite se-

quence. Before you fix the screw, make

sure that the burner is pushed correctly to

the back panel.

Minimum level adjustment of the oven

burner:

1. Disconnect the mains plug from the mains

socket.

2. Remove the knob for the oven functions.

3. Adjust the adjustment screw (A) with a

thin-bladed screwdriver.

Change of the type

of gas

Adjustment of the

adjustment screw

From natural gas to

liquid gas

Fully tighten the ad-

justment screw in.

From liquid gas to

natural gas

Release the adjust-

ment screw approxi-

mately 3/4 of a turn.

4. Attach the knob for the oven functions.

5. Put the mains plug into the mains socket.

Warning! Only put the mains plug into the

mains socket when all parts are back into

their initial position. There is a risk of injury.

6. Light the gas oven burner. Refer to section

"Gas oven cooking: Ignition of the gas

oven burner".

7. Set the knob for the oven functions to max-

imum and let the oven heat for at least 10

minutes.

www.zanussi.com

La page est en cours de chargement...

Zanussi ZCG664GW Manuel utilisateur

Marque: Zanussi

Modèle: ZCG664GW

Catégorie: Cuisinières

Taper: Manuel utilisateur

Ce manuel convient également à

ZCG664GX

Télécharger le PDF

rapport

dans d''autres langues

English: Zanussi ZCG664GW User manual

Zanussi ZCG664GW Manuel utilisateur

Ce manuel convient également à

Zanussi ZCG664GW Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents