Smooth Fitness 9.65LC Manuel utilisateur

REV 11011 USER’S MANUAL

9.65LC MOTORIZED TREADMILL

USER WEIGHT LIMITATION: 400lbs(180kgs).

SERIAL NUMBER (found on frame):

2 9.65 LC TREADMILL

PRECAUTIONS

For future service or related questions:

Please staple your receipt and/or write in the name and phone number of the retail store where you purchased your treadmill.

Name: ______________________________ Phone Number: ___________________ Receipt: ______________________

Precautions:

WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons, read the following important precautions

and information before operating the treadmill. It is the responsibility of the owner to ensure that all users of this treadmill are

adequately informed of all warnings and precautions.

• Use the treadmill only as described in this manual.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use

of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play

with this machinery

• Place on a level surface, with 6 feet (2 m) of clearance behind it. Do not place the treadmill on any surface that blocks air

openings. To protect the floor or carpet from damage, place a mat under the treadmill.

• When choosing a location for the treadmill be sure that the location and position permit access to a plug.

• Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a garage or covered patio, or near

water.

• Do not operate the treadmill where aerosol products are used or where oxygen is being administered.

• Keep children under the age of 12 and pets away from the treadmill at all times.

• The treadmill should not be used by persons weighing more than 400LBS (180 Kgs).

• Never allow more than one person on the treadmill at a time. Wear appropriate exercise clothing when using the treadmill.

Do not wear loose clothing that could become caught in the treadmill. Athletic support clothes are recommended for both

men and women. Always wear athletic shoes. Never use the treadmill with bare feet, wearing only stockings, or in

sandals.

• When connecting the power cord, plug the power cord into a grounded circuit. No other appliance should be on the same

circuit.

• Always straddle the belt and allow it to start moving before stepping onto the belt.

• Always examine your treadmill before using to ensure all parts are in working order.

• Allow the belt to fully stop before dismounting.

• Never insert any object or body parts into any opening.

• Follow the safety information in regards to plugging in your treadmill.

• Keep the power cord away from the incline wheels and do not run the power cord underneath your treadmill. Do not

operate the treadmill with a damaged or frayed power cord.

• Always unplug the treadmill before cleaning and/or servicing. Service to your treadmill should only be performed by an

authorized service representative, unless authorized and/or instructed by the manufacturer. Failure to follow these

instructions will void the treadmill warranty.

• Never leave the treadmill unattended while it is running.

• Use “safety key” when operating the treadmill and make sure the “safety key” is clipped to the users clothing.

• Remove the “safety key” and store it in a safe place when the treadmill is not in use. Keep the “safety key” away from

children.

www.smoothfitness.com

3

PRECAUTIONS

Pour réparations futures ou questions connexes :

Please staple your receipt and/or write in the name and phone number of the retail store where you purchased your treadmill.

Name: ______________________________ Phone Number: ___________________ Receipt: ______________________

Précautions:

AVERTISSEMENT : Pour réduire les risques de brûlures, d’incendie, de choc électrique ou de blessures aux personnes, lire les

précautions importantes et l’information suivantes avant de se servir du tapis roulant. Il revient au propriétaire de s’assurer que tous

les utilisateurs de ce tapis ont bien été informés de tous les avertissements et précautions.

• Utiliser le tapis seulement comme il est décrit dans ce manuel.

• Cet appareil n'est pas destiné à être utilisé par des personnes (enfants compris) dont les capacités physiques,

sensorielles ou mentales, ou le manque d'expérience et de connaissances, à moins qu'elles n'aient été formées et

encadrées instructions concernant l'utilisation de l'appareil par une personne responsable de leur sécurité . Les enfants

doivent être surveillés pour s'assurer qu'ils ne jouent pas avec cette machine

• Le placer sur une surface plane, en laissant 2 m (6 pi) d’espace libre en arrière. Ne pas placer le tapis roulant sur une

surface qui bloque les ouvertures d’air.

• Pour protéger le plancher ou un tapis de dommages, placer un petit tapis sous le tapis roulant.

• Choisir pour le tapis roulant un emplacement et une position qui permettent d’avoir accès à une prise murale.

• Garder le tapis roulant à l’intérieur, à un endroit sans humidité ni poussière. Ne pas mettre le tapis roulant dans un garage,

sur une terrasse couverte ou près de l’eau.

• Ne pas faire fonctionner le tapis roulant pendant la vaporisation de produits aérosol ou l’administration d’oxygène.

• Ne pas laisser les enfants de moins de 12 ans et les animaux s’approcher du tapis roulant.

• Le tapis roulant ne doit pas être utilisé par des personnes pesant plus de 400 lbs (180 kg).

• Il ne doit jamais y avoir plus d’une personne sur le tapis à la fois. Porter des vêtements d’exercice appropriés pour utiliser

le tapis roulant. Ne pas porter de vêtements lâches qui pourraient être pris dans le tapis roulant. Les vêtements de soutien

athlétiques sont recommandés tant pour les hommes que pour les femmes. Porter toujours des chaussures d’athlétisme.

Ne pas être pieds nus, ou porter seulement des chaussettes ou des sandales lors de l’utilisation du tapis roulant.

• Brancher le cordon d’alimentation dans un circuit avec mise à la terre. Aucun autre appareil ne doit être sur le même

circuit.

• Toujours enjamber le tapis et le laisser commencer à rouler avant de monter dessus.

• Toujours examiner votre tapis roulant avant de l’utiliser pour s’assurer que toutes les pièces fonctionnent correctement.

• Laisser le tapis s’arrêter complètement avant de descendre.

•

Ne jamais insérer d’objets ou de parties du corps dans une ouverture.

• Suivre les directives de sécurité en ce qui concerne le branchement de votre tapis roulant.

• Garder le cordon d’alimentation éloigné des roues inclinées et ne pas faire passer le cordon d’alimentation sous votre

tapis roulant. Ne pas faire fonctionner le tapis roulant si le cordon d’alimentation est endommagé ou effiloché.

• Débrancher toujours le tapis roulant avant de le nettoyer ou de le réparer.

• Toute réparation au tapis doit être effectuée par un réparateur agréé, à moins d’autorisation ou de directives contraires du

fabricant. Le non-respect de ces instructions annulera la garantie du tapis roulant.

• Ne jamais laisser le tapis roulant sans surveillance lorsque la clé de sécurité est insérée.

• Utiliser la « clé de sécurité » pour faire fonctionner le tapis roulant et s’assurer qu’elle est accrochée aux vêtements des

utilisateurs

• Retirer la « clé de sécurité » et la ranger dans un endroit sûr lorsque le tapis roulant n’est pas en fonction. Garder la « clé

de sécurité » hors de la portée des enfants

4 9.65 LC TREADMILL

POWER REQUIREMENTS

Power Requirements:

IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESULT IN THE RISK OF AN ELECTRIC

SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE MAN IF YOU ARE IN DOUBT AS TO WHETHER THE

PRODUCT IS PROPERLY GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE PRODUCT, IF IT WILL NOT FIT

THE OUTLET; HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN.

This treadmill can be seriously damaged by sudden voltage changes in your home’s electrical power. Voltage spikes, surges and

noise interference can result from weather conditions or from other appliances being turned on or off. To reduce the possibility of

treadmill damage, always use a surge protector (not included) with your treadmill.

Surge protectors can be purchased at most hardware stores. The manufacturer recommends a single outlet surge protector with a

UL 1449 rating as a Transient Voltage Surge Suppressor (TVSS) with a UL suppressed voltage rating of 400V or less and an

electrical rating 110VAC, 15 amps.

This treadmill must be grounded to reduce the risk of electrical shock. Grounding provides a path of least resistance for electric

current, should the treadmill malfunction. This treadmill is equipped with an electrical cord that has an equipment-grounding

conductor and a grounding plug. Always plug the power cord into a surge protector, and plug the surge protector into an

appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

This product is for use on a nominal 110-volt circuit, and has a grounding plug that looks like the plug illustrated in the drawing

below.

GFCI outlets and GFCI Circuit Breakers are NOT recommended for use on this product. GFCI outlets and GFCI Circuit Breakers

may cause this equipment to function improperly.

www.smoothfitness.com

5

POWER REQUIREMENTS

Alimentation :

UN MAUVAIS BRANCHEMENT DU CONNECTEUR DE MISE À LA TERRE DE L’ÉQUIPEMENT POURRAIT PROVOQUER UN

CHOC ÉLECTRIQUE. EN CAS DE DOUTE, CONSULTER UN ÉLECTRICIEN OU UN RÉPARATEUR QUALIFIÉ POUR SAVOIR

SI LE PRODUIT EST CORRECTEMENT MIS À LA TERRE. NE PAS MODIFIER LA FICHE FOURNIE AVEC LE PRODUIT. SI

ELLE N’ENTRE PAS DANS LA PRISE, FAIRE INSTALLER UNE PRISE APPROPRIÉE PAR UN ÉLECTRICIEN

PROFESSIONNEL.

Ce tapis roulant pourrait être gravement endommagé en cas de changement soudain de tension dans votre alimentation électrique.

Les conditions météorologiques ou la mise sous tension ou hors tension d’autres appareils électriques peuvent provoquer des

pointes de tension, des surtensions ou un brouillage. Pour réduire la possibilité que le tapis soit endommagé, toujours utiliser un

limiteur de surtension (non inclus) avec votre tapis roulant.

Il est possible d’acheter des limiteurs de surtension dans la plupart des quincailleries. Le fabricant recommande un limiteur de

surtension UL 1449 à prise unique comme suppresseur de tension transitoire (TVSS) ayant un taux de suppression de tension de

400 V ou moins et une tension électrique de 110 V C.A., 15 A.

Ce tapis roulant doit être mis à la terre pour réduire le risque de choc électrique. La mise à la terre fournit une voie de moindre

résistance au courant électrique en cas de mauvais fonctionnement du tapis roulant. Ce tapis roulant est équipé d’un cordon

électrique avec un conducteur de mise à la terre et une fiche de mise à la terre. Brancher toujours le cordon électrique dans un

limiteur de surtension et brancher le limiteur de surtension dans une prise appropriée, correctement installée et mise à la terre

conformément à tous les codes locaux et ordonnances.

Ce produit doit être utilisé avec un circuit nominal de 110 volts et à une fiche de mise à la terre qui ressemble à celle illustrée ci-

dessous.

Les prises avec disjoncteur de fuite de terre et les disjoncteurs de fuite de terre ne sont PAS recommandés pour ce produit. Les

prises avec disjoncteur de fuite de terre et les disjoncteurs de fuite de terre pourraient provoquer un mauvais fonctionnement de cet

équipement.

6 9.65 LC TREADMILL

BEFORE YOU BEGIN

Open the boxes:

Open the boxes of your new equipment. Inventory all parts included in the boxes, and Supplied Hardware lists

on page 7 for a full count of the parts included. If you are missing any parts or have any questions contact us

directly at 888-800-1167

Gather your tools:

Before you begin, make sure that you have gathered all the necessary tools you may require to assemble the unit

properly. Having all of the necessary equipment at hand will save time and make the assembly quick and hassle-free.

Clear your work area:

Make sure that you have cleared away a large enough space to properly assemble the unit. Make sure the space is

free from anything that may cause injury during assembly. After the unit is fully assembled, make sure there is a

comfortable amount of free area around the unit for unobstructed operation.

Invite a friend:

Some of the assembly steps may require heavy lifting. It is recommended that you obtain the assistance of another

person when assembling this product.

User Weight Limitation:

Please note that there is a weight limitation for this product. If you weigh more than 400LBS (Approx. 180 Kgs). It is

not recommended that you use this product. Serious injury may occur if the user’s weight exceeds the limit shown

here. This product is not intended to support users whose weight exceeds this limit.

Care and maintenance:

The safety level can be maintained only if it is examined for damage and wear.

Replace any defective components immediately and stop all use of the equipment until repaired.

Always take care when mounting the equipment. Straddle the equipment by placing your feet on the straddle rails.

Dismount from the equipment only after all parts have stopped.

Always check the wear and tear components like pulley, belts, etc.…To prevent injury.

There is an emergency stop, in the form of a SAFETY KEY, to prevent injury; you can stop the treadmill immediately

by actuating the emergency stop for emergency dismount.

www.smoothfitness.com

7

SUPPLIED COMPONENTS / SUPPLIED HARDWARE

This list identifies the major components you will use to assemble this product.

MAIN BODY

CONSOLE MAST

Bottle Holder

CONSOLE

GPIB

HARDWARE KIT

M10x15 HEX HEAD BOLT20pcs

washer 20pcs

M4x15 Cross self-tapping

screws 8pcs

lubricant for running deck

SAFETY KEY

Allen wrench 1 pcs

Millimeters

Console crossbar

8 9.65 LC TREADMILL

COMPLETE PARTS LIST

ITEM DESCRIPTION QTY ITEM DESCRIPTION QTY

1 main frame 1 45 Incline motor 1

2 transformer 1 46 hexagon m10*50mm 1

3 filter 1 47 washer 4

4 Control pcb 1 48 Nut 10 4

5 screw M4*10mm 9 49 bolt M10*115mm 1

6 Nut 4 8 50 washer 4

7 screw M4*14mm 2 51 incline frame 1

8 fixing bracket of motor 1 52 bushing 2

9 motor 1 53 Moving wheel 2

10 hex socket head bolt M8*12mm 2 54 bolt M10*75mm 2

11 bolt M8*35mm 8 55 washer 2

12 washer 4 56 Nut M12 2

13 Spring washer 6 57 bolt M12*60mm 2

14 Nut M8 4 58 Connect wire set 1

15 hexagon m8*110mm 2 59 right console mast 1

16 fixing board of power 1 60 left console mast 1

17 on/off switch 1 61 bolt M10*20mm 16

18 Socket 1 62 washer 16

19 fuse 1 63 Console frame 1

20 screw M3*10mm 10 64 console lower cover 1

21 screw M4*15mm 53 65 heart rate panel 1

22 Screw4*8 25 6 co sole upper cover 1

23 Screw3*30 4 67 console cover 1

24 MOTOR RON COVER 1 68 Console PCB 1

25 screw M6*10MM 4 69 Steel shim 1

2 driving belt 1 70 safety key 1

27 front roller 1 71 magnet 1

28 rear roller 1 72 Power wire 1

29 running belt 1 73 speaker 2

30 hex socket head bolt M8*35mm 1 74 Speaker cover 2

31 hex socket head bolt M8*65mm 1 75 Fixing board of speaker 2

32 hex socket head bolt M8*90mm 2 76 MP3 interface 1

33 washer 4 77 Keystroke panel 1

34 running deck 1 78 Handle keystroke panel 1

35 bolt M8*35mm 10 79 Amplifier PCB 1

36 rubber cushion 8 80 handle up cover 2

37 motor sensor wire 2 81 handle lower cover 2

38 Console wire 1 82 Handle keystroke panel 1

39 rubber pad 10 83 handle pulse set 2

40 motor cover 1 84 Console crossbar 1

41 side rein 2 85 Bottle Holder 1

42 Left end cover 1 86 Right rubber ring 1

43 right end cover 1 87 Left rubber ring 1

44 Control-console wire 1

www.smoothfitness.com

9

COMPLETE DIAGRAM

Console

Motor cover

Running belt

Handle

Handle pulse

rear roller cover

Moving wheel

Rear roller

Console mast

Bottle holder

10 9.65 LC TREADMILL

COMPLETE PARTS DIAGRAM 2

www.smoothfitness.com

11

ASSEMBLY

–

PLEASE READ ALL STEPS BEFORE BEGINNING YOUR WORK.

STEP1: Assemble Console Mast to Base Frame.

NOTE: Make sure all wires are recessed into the frame. DO NOT trap or

pinch. DO NOT tighten bolts until STEP2.

When attaching the Right upright (59) first feed the Lower Console Wire through

the upright.

1). Attach Left and Right Uprights into base frame, and secure using the 8

M10x20mm Bolts (61) 8 M10 Washers (62).

61 X8

62 X2

Bolts should be hand tight only

12 9.65 LC TREADMILL

ASSEMBLY

STEP2: Attach Console to Left and Right Uprights

1). Connect the Upper Console Wire (38) from the console set to Lower Console

Wire (44) in the right upright, Then place the excess wire and the connectors into

right upright.

2). Place the entire console set onto the uprights, and secure the left side using 4

x M10x20mm Bolt (61) with 4 x M10 Washer (62)

3). Repeat the above process for the Right side

4). Hand tighten bolts olny

61 X8

62 X8

Caution Pinch point! Do not pinch wires between frame.

Ensure the pins are straight when connecting

Bolts should be hand tight only

www.smoothfitness.com

13

ASSEMBLY

STEP3: Fasten protective cover on the upright

1) Attach the crossbar (84) between the left and right upright then secure using

4 x M8x20mm Bolts () and 4 x M8 washers ().

2) Tighten all bolts and fasteners now

X4

Console crossbar

Tighten all bolts and fasteners now

14 9.65 LC TREADMILL

ASSEMBLY

STEP4: Assembly of the bottle holde

r

to the cross ba

r

Attach the Bottle holder to the crossbar, and secure using 8 x M4x15mm screws

().

X8

Tighten all bolts and fasteners now

204

www.smoothfitness.com

15

ASSEMBLY

STEP 5:

1) Turn power switch on

2) Insert the Safety Key (70) into the Bottom Center of Console prior to

operation.

Note:Your treadmill will not Function without the safety key.

70 X1

Power Switch

16 9.65 LC TREADMILL

COMPUTER OPERATION

Computer Display

Time 00:00-99:59 Min

Speed 0.5-12.5 mile/h

incline 0-15%

Distance 0.00-99.9 mile

Calories 0-999 KCAL

Pulse 70-200 / Min

Goal 0-100%

Age 15-80 years

Weight 88-400 lbs

Level L1-L10

Mode P1-P14

Height 4.0-7.2ft

Sex Male ,female

Target HR 50-190

www.smoothfitness.com

17

COMPUTER OPERATION

START (Quick Start):

Press the “START “to begin your exercise

PAUSE:

Press the “STOP＂ button to pause the

training.

RESET:

Press the “ STOP ＂ button for a few

seconds to reset the computer to its

default values.

SELECT:

Press select to confirm set values for time,

distance, calories, weight, height, program

settings and to scroll between the

computer readout during your workout.

SPEED + / - KEYS:

Use the speed + / - to scroll through the

programs, program levels, to enter the

time, distance, calories, height, weight,

age and heart rate. The keys will also

increase and decrease your speed during

the workout.

18 9.65 LC TREADMILL

COMPUTER OPERATION

▲ / ▼ KEYS:

Use to adjust the incline level up or down

during the workout

QUICK SPEED KEY:

Use the quick speed keys to achieve the

predetermined speed with the push of one

button.

QUICK INCLINE KEY:

Use the quick incline keys to achieve the

predetermined incline with the push of one

button.

SPEAKER PORT:

When you use speaker, please insert the

audio signal into input interface.

HANDRAIL KEY：

Use the keys on right handrail to increase

or decrease the speed.

Use the keys on left handrail to increase or

decrease the incline

www.smoothfitness.com

19

COMPUTER OPERATION

12.0

8

KPH

MPH

SPEED

WEIGHT

AGE

MODE

RUNNING

INTERVAL

WEIGHT-LOSSFATBUN

CARDIO

LEVEL

KM

%

GOAL

PLUSE

SPEED

8.0

INCLINE

CALORIES

9:00

DISTANCE

28:52

TIME

A

TIME

Displays minutes and seconds of the elapsed or remaining time.

B

DISTANCE

Displays the completed or remaining distance in miles.

C

CALORIES:

Displays estimated use of calories at the time of display

INCLINE:

Displays the current running incline.

D

Pulse

Displays the current heart rate

Goal:

Displays the percentage of the program completed.

SPEED:

Displays the program setup speed.

SPEED SEGMENT NUMBER.

Display the segment number during the creation of a custom course.

INCLINE SEGMENT NUMBER.

Display the segment number during the creation of a custom course.

E

SPEED GRAPH / INCLINE GRAPH

Displays boththe speed and incline profile. Press select to toggle between both profiles.

GENDER SETTING DISPLAY

display the diagram of male and female

BFR/BMI/BMR

Displays BFR/BMI/BMR.

F

PROGRAM

Displays the selected training program number.

SPEED

Displays the current running speed.

AGE

Displays the age during program setup.

WEIGHT

Displays the weight during program setup.

HEIGHT

Displays the height during program setup..

TEST RESULT OF “BFR/BMI/BMR”

Displays the number value of BFR/BMI/BMR.

A

D

A

C

B

E

F

20 9.65 LC TREADMILL

COMPUTER OPERATION

G

PROGRAM

Displays program discription

ERROR PROMPTING

Displays the computer error codes

G

La page charge ...

Smooth Fitness 9.65LC Manuel utilisateur

Ce manuel convient également à

Smooth Fitness 9.65LC Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents