Ozone buzz Le manuel du propriétaire

Marque: Ozone

Modèle: buzz

Taper: Le manuel du propriétaire

Thank You ...........................................................................

Warning ..............................................................................

Team Ozone ........................................................................

Your Buzz ............................................................................

Bag ....................................................................................

Brake Lines .........................................................................

Risers .................................................................................

Accelerator System ...............................................................

Harness ..............................................................................

Total weight in flight .............................................................

Basic Flight Techniques..........................................................

Pre Flight Check List..............................................................

Practice Flights.....................................................................

Take-off Check List................................................................

Launching............................................................................

Ground Handling...................................................................

In Flight Characteristics..........................................................

Normal Flight........................................................................

Active Flying.........................................................................

Turning ...............................................................................

Landing ..............................................................................

Packing ...............................................................................

Advanced Flight Techniques ...................................................

Descent Techniques ..............................................................

Big Ears ..............................................................................

Big Ears and Accelerator ........................................................

Big Ears and Spiral Dive ........................................................

Wingovers ...........................................................................

B-Line Stall .........................................................................

Spiral Dives .........................................................................

Incidents ............................................................................

Deep Stall / Parachutal Stall ...................................................

Deflations ...........................................................................

Cravats ...............................................................................

Acrobatic Flying ...................................................................

Towing................................................................................

Paramotoring .......................................................................

Matrials ..............................................................................

Caring for Your Buzz .............................................................

Storage ..............................................................................

Cleaning .............................................................................

Repairs ...............................................................................

Maintenance Checks .............................................................

Modifications .......................................................................

Ozone Quality and Service ....................................................

Summary ............................................................................

Riser Arrangement ...............................................................

Service Card

CONTENTS

THANKYOU!

Thank you for choosing to fly an Ozone Buzz.

As a team of free flying enthusiasts and adventurers, Ozone's mission

is to build sweet handling, agile paragliders that produce 'cutting

edge' performance, whilst still keeping you safe in rough air.

All our research and development is concentrated on creating the

best handling characteristics possible with optimum security.

Confidence and belief in your paraglider is a far greater asset than

any small gains in performance - ask any of the Ozone pilots on your

local hills, or those who have taken our gliders on ground-breaking

adventures and stood on podiums around the world.

Our development team is based in the south of France. This area,

which includes the sites of Gourdon, Monaco and Lachens guarantees

us more than 300 flyable days per year; this is a great asset in the

development of the Ozone range.

As pilots we fully understand just how big an investment a new

paraglider is. We know that quality and value for money are essential

considerations when choosing your new paraglider; so to keep costs

low, and quality high we now build all our wings in our own

production plant. This way we can guarantee that all our paragliders

meet the same high standards that we expect ourselves.

This manual will help you get the most out of your BUZZ. It details

information about the BUZZ's design, tips and advice on how best to

use it and how to care for it to ensure it has a long life and retains a

high resale value. Along with this manual you will also have received

a service card giving the technical specifications of your glider, line

layout diagram, line length check table and a service record sheet,

please make sure this is completed when you get your glider

sercveiced and keep the card with the glider in case you need to

replace a line.

If you need any further information about Ozone, the BUZZ, or any

of our products then please check www.flyozone.com or contact your

local dealer, school or any of us here at Ozone.

It is essential that you read this manual before flying your

BUZZ for the first time.

Please ensure that this manual is passed on to the new owner

if you ever resell this paraglider.

Ozone's web site, www.flyozone.com or

www.flyozone.com//pgframe.asp?pge=gliders-buzz.htm

carries up-to-date information, including any safety issues or

issues specific to your Buzz. Please check it regularly.

Safe Flying

All the team @ Ozone

WARNING

Paragliding is a potentially dangerous sport that can cause serious

injury including bodily harm, paralysis and death.

Flying an Ozone paraglider is undertaken with the full knowledge that

paragliding involves risks.

As the owner of an Ozone paraglider you take exclusive responsibility

for all risks associated with its use. Inappropriate use and or abuse

of your equipment will increase these risks.

Ozone paragliders are only suitable for qualified pilots or those under

instruction.

Any liability claims resulting from use of this product towards the

manufacturer, distributor or dealers is excluded.

Make sure you seek professional tuition and learn with a reputable

school.

Be prepared to practise as much as you can especially ground

handling as this is a critical aspect of paragliding; poor control whilst

on the ground is one of the most common causes of accidents.

Be ready to continue your learning by attending advanced courses to

follow the evolution of our sport, techniques and materials keep

improving.

Use only certified paragliders, harnesses with protector and reserve

parachutes that are free from modification, and use them only within

their certified weight ranges. Please remember that flying a glider

outside its certified configuration may jeopordise any insurance (e.g.

liability, life etc) you have. It is your responsibility as the pilot to

verify your insurance cover.

Make sure you complete a thorough daily and pre-flight inspection of

all of your equipment. Never attempt flying with unsuitable or

damaged equipment.

Always wear a helmet, gloves and boots.

All pilots should have the appropriate level of license for their

respective country and third party insurance.

Make sure that you are physically and mentally healthy before flying.

Choose the correct wing, harness and conditions for your level of

experience.

Pay special attention to the terrain you will be flying and the weather

conditions before you launch. If you are unsure then don't fly, and

always add a large safety margin to all your decisions.

Avoid flying your glider in rain, snow, strong wind, and turbulent

weather conditions or clouds.

If you use good, safe judgement you will enjoy many years of

paragliding.

Remember, PLEASURE is the reason for our sport.

YOURBUZZ

The Buzz is suitable for low airtime pilots who are learning and

discovering this wonderful sport as well as more experienced pilots

who want maximum safety, performance and fun. The Buzz has

everything you need to help your flying progress to higher levels. It

will take you all the way to cloudbase and beyond with confidence,

fuelling your addiction for aerial adventures.

Our aim whilst designing the Buzz, was to produce a 'low end' DHV

1-2 which has Ozone's trademark handling, safety and performance.

It has been certified at DHV 1-2 with nearly all of the tests passing

DHV1. Dav and the team have worked hard to create a forgiving

wing whilst maintaining the handling and feedback a pilot needs to

learn and progress.

On the ground the Buzz is superb. Alpine and reverse launches are

simple, inflation is smooth and progressive with a positive pressure

through the risers; this makes it easy to feel exactly where the glider

is. Launches are easy to control as the wing has very little tendency

to over fly the pilot.

In the air the Buzz is a joy to fly, brake pressure is perfect, building

continuously as more brake is applied and becoming progressively

harder as the stall / spin point is reached. The Buzz offers just the

right amount of feedback through the risers and brakes, helping you

feel and learn about the thermals and rough air without overloading

your senses with too much unnecessary information.

The wing is well damped in pitch, this helps it cut through turbulence

efficiently, making it very resistant to deflations and improving its re-

inflation characteristics.

Handling is amazing, changes in direction are no problem as it bites

into thermals and carves into turns. Roll rate is good and can be

easily controlled with a little outside brake while soaring or

thermalling. Smooth and flat or banked up - cranking it round, either

way you'll love it!

Sink rate and glide performance are excellent for a wing with such

safety, making your route to cloudbase and XC's that much easier.

TEAMOZONE

Everyone at Ozone continues to be driven by our passion for flying,

our love of adventure and our quest to see Ozone's paraglider

development create better, safer and more versatile paragliders.

Paragliding design is led by the ever thoughtful Dav Dagault and Rob

Whittall who just don't ever stop; they are pilots with a wealth of

experience both in competition and adventure flying, as well as PG

design. Also on the design team are test pilots Jerome Canaud, a

true acro spirit who has instructed paragliding and Russell Ogden, top

competition pilot and paragliding instructor - they can usually be

found putting Dav's latest creation through a series of acro

manoeuvres.

Back in the office Mike 'Da Boss' Cavanagh and Sam Lowe generally

keep control of the mayhem. Making sure that your glider gets from

our factory to you as quickly as possible is Claire Drury, Meanwhile

hidden in a corner, trying to avoid looking at the flyable conditions

outside are Marcus King and Manu Prissette who look after all our

adverts, videos and communication, as well as trying to keep the

computers running. New member Ivan Bellia is in charge of

designing our new range of accessories. Downstairs Karine Marconi

makes sure we don't spend too much money whilst if you phone us

you are likely to hear the dulcet tones of Nicky Watts.

Our manufacturing facility in Vietnam is headed up by Dr Dave

Pilkington, who works relentlessly manufacturing gliders and

producing prototypes as well as researching materials and

manufacturing processes for our future products. He is backed up by

Ngan and 170 production staff.

The Buzz has a large useable speed range to help you out on the

sinky glides or when you need to push into a headwind. At full speed

the leading edge remains solid, even in turbulence.

The Buzz is a perfect choice for new pilots or for those seeking

unparalleled security and performance. It will take you as far as you

want to go whilst inspiring you with confidence and putting a smile

on your face. We love to hear feedback on our wings, good or bad,

so let us know about your adventures with your Buzz.

Bag

The bag has been designed to be comfortable and useful (padded hip

belt, ergonomic and adjustable shoulder straps). Its large volume will

allow you to store all your kit whilst still being comfortable for hiking.

We've also added some pockets on the side and on the top, handy for

all those easily lost accessories.

Brake Lines

The brake line lengths have been set carefully during testing. We feel

it is better to have slightly long brake lines and to fly with a wrap

(one turn of line around the hand). However, if you do choose to

adjust them, please bear in mind the following:

• Ensure both main brake lines are of equal length.

• If a brake handle has been removed, check that its line is still

routed through the pulley when it is replaced.

• When the brake handles are released in flight, the brake lines

should be slack. There must be a substantial "bow" in them to

guarantee no deformation of the trailing edge.

• There must be a minimum of 10cm of free play before the brakes

begin to deform the trailing edge. This prevents the trailing edge

from being deformed when using the speed system.

IMPORTANT : In the unlikely event of a brake line snapping in

flight, or a handle becoming detached, the glider can be flown

by gently pulling the rear risers (C-risers) for directional

control.

Risers

To make the glider simple to fly, we've designed the BUZZ with only

3 risers. Each riser is covered with coloured webbing, which makes

them easy to identify.

The A's are RED. You will notice that the A's are split in two parts.

The small riser on the back, holding only one line, is the "Baby A"; it

has been designed to make applying "Big Ears" simple.

The B's are BLUE

The C's are BLACK.

Accelerator System

To set up an accelerator on the ground, ask a friend to pull your risers

into their in-flight position whilst you sit in your harness. Now adjust

the length of the line so that the main bar sits just beneath your seat.

You should now be able to hook your heel in to the secondary (lower)

loop of the accelerator.

The accelerator must be slack enough to ensure that the front risers

are not pulled down in normal flight, but not so long that it is

impossible to use the full speed range of the BUZZ.

Extending the secondary (lower) loop of the accelerator fully will take

the BUZZ through approximately half its accelerated speed range.

This is as much speed as you will normally need in general flight.

Should you need even more speed you should hook your feet on to

the upper bar, which you can then extend until the pulleys on the

risers touch.

Once set up test the full range of the accelerator in calm flying

conditions; ensure that both risers are pulled evenly during

operation. Fine-tuning can be completed when you are back on the

ground.

IMPORTANT : For better penetration in headwinds you can fly

faster by using the accelerator system. Using the accelerator

decreases the angle of attack and can make the glider more

likely to collapse, therefore using the accelerator near the

ground should be avoided.

We would advise you not to use the accelerator when flying in

turbulence. Inexperienced pilots are recommended not to use

the accelerator system until they are fully accustomed to the

glider. Although all gliders are designed and tested with an

accelerator system, most experienced pilots hardly ever use

the full speed range, especially in turbulent conditions.

Harness

It will be in your harness that you will enjoy flying... Therefore, we

recommend you spend the time necessary to adjust your harness's

different settings, which will make flying more pleasurable, because

you are comfortable.

The shoulder's straps and the hip's strap are the ones to set (make

sure you do not have your shoulder's strap too tight, or you might

find it difficult to get seated after launching). Your ideal position in

your harness should be sat, with your back leaning slightly

backwards.

The chest strap should be set at 42, 44, 46cm (between the centres

of the risers) for sizes S, M, L respectively.

Total weight in flight

Each BUZZ has been certified for a defined weight range. We

recommend that you respect these weight ranges. If you are

between sizes the following information may help you make a

decision as to which size to buy:

If you want better speed, precise handling, if you generally fly in

mountains and/or in strong conditions, you should chose to fly in the

top part of the weight range.

If you want a better sink rate, if you generally fly in flat lands and/or

in weak conditions, you should chose to fly in the bottom part of the

range.

BASIC FLIGHT TECHNIQUES

To familiarise yourself with the glider it is a good idea to perform

practice inflations and small flights on a training hill. This will enable

you to set up your equipment correctly. If in any doubt please get

advice and help from your local dealer or instructor.

Preparation

Lay out the BUZZ on its top surface in a pronounced arc, with the

centre of the wing higher than the tips. Lay out the lines one side at

a time. Hold up the risers and starting with the brake lines, pull all

lines clear. Repeat with the C, B and A lines, laying the checked lines

on top of the previous set, and making sure no lines are tangled,

knotted or snagged. Mirror the process on the other side.

Take-off check list:

1. Check reserve parachute - pin in and handle secure

2. Helmet on and fastened

3. All harness buckles closed - check leg-loops again

4. Karabiners and maillons tight

5. Holding the A's and your brake handles

6. Leading edge open

7. Aligned directly into wind

8. Airspace and visibility clear

Launching

Your BUZZ will launch with either the forward or reverse techniques.

Whilst inflating your wing, you should hold both of the A risers (main

A and babyA) on each side. Once clipped in, and you have gone

through the take-off check list (above), stand central to the wing to

ensure an even and progressive inflation.

Forward Launch - Nil to Light winds

When the wind is right, move forward, your lines should become tight

within one or two steps. The BUZZ will immediately start to inflate.

You should maintain a constant pressure on the risers until the wing

is overhead.

Don't pull down or push the risers forward excessively, or the leading

edge will deform and make taking-off difficult.

Move smoothly throughout the entire launch, there is no need to rush

or snatch at it. You should have plenty of time to look up and check

your canopy before committing yourself.

Once you are happy that the BUZZ is inflated correctly, accelerate

smoothly off the launch.

Reverse Launch -Light to Strong Winds

Lay out your BUZZ as you would for the forward launch. However,

this time turn to face the wing, passing one entire set of risers over

your head as you turn. Now you can pull the BUZZ by it's A-risers.

Once the wing is overhead, brake it gently, turn and launch.

In stronger winds, be prepared to take a few steps towards the glider

as it inflates. This will take some of the energy out of the glider and

it will be less likely to over fly you. This reverse-launch technique can

be used in surprisingly light winds too.

IMPORTANT: Never take off with a glider that is not fully

inflated or if you are not in control of the pitch/roll of your

wing.

Practice ground handling a lot! It's great fun, and will give you a

much better feel for your BUZZ's flight characteristics. It will also

improve your overall enjoyment of flying by making your launches

easier.

In Flight Characteristics

The Buzz shows no unusual flying characteristics, consequently it is

suitable for a very wide range of pilot. In turns, the BUZZ is smooth

and co-ordinated, on glides it remains solid and well pressured, even

through the accelerated speed range. It has a very high resistance to

both collapses and stalls. However, to get the most out of your BUZZ

we advise you to consider the following information.

Normal Flight

Flying at 'trim speed' (hands-up), your glider will achieve its 'best

glide' speed. Apply the brakes approximately 30cm to reach the

minimum-sink rate. To increase your speed for headwind glides, use

the accelerator bar which will give you an increase in speed of up to

10km/h.

Active Flying

To minimise the likelihood of suffering collapses in turbulent

conditions, it is essential to use active flying.

All good pilots react to the feedback the gliders send them, and are

constantly adjusting their speed and pitch to match the movements

of the air. The key elements of active flying, are pitch control and

pressure control:

As the glider pitches in front of you, use the brakes to slow it down.

Equally, as the glider drops behind you, release the brakes to allow it

to speed up.

Flying with a bit of brake applied (approx 20cms) will give you feed

back from the wing. In turbulent conditions the internal pressure of

the wing can change and you can feel this through the brakes. The

aim is to maintain a constant pressure through the brakes. If you feel

a loss in pressure apply the brakes until normal pressure is resumed

then raise hands back to original position (this must be done quickly).

Avoid flying with continuous amounts of brake in rough air as you

could inadvertently stall the wing. Always consider your airspeed.

These movements can be symmetric or asymmetric; you may have

to apply both brakes or just one. These subtle adjustments will keep

the glider flying smoothly and directly above you and dramatically

reduce the chances of a collapse. These are skills are best learnt by

playing with the glider on the ground!

IMPORTANT: No pilot and no glider are immune to collapses

however active flying will virtually eliminate any tendency to

collapse. When the conditions are turbulent, be more active

and anticipate the movements of your wing. Always be aware

of your altitude and do not over-react. We advice you to keep

hold of your brakes. Do not fly in turbulent conditions.

Turning

To familiarise yourself with the BUZZ your first turns should be

gradual and progressive.

To make efficient and co-ordinated turns with the BUZZ first look in

the direction you want to go, then lean into it. Your first input for

directional change should be weight-shift, followed by the smooth

application of the brake until the desired bank angle is achieved. To

regulate the speed and radius of the turn, use the outer brake.

IMPORTANT : never initiate a turn at minimum speed (i.e.

with full brakes on) as you could risk entering a spin.

Landing

The BUZZ shows no unusual landing characteristics but as a

reminder, here are some tips.

• Always set up your landing early, give yourself plenty of options

and a safe margin for error.

• Once below 30 metres avoid turning tightly as the glider will have

to dive to accelerate back to normal flight. If you are at low

altitude, or if you hit sink, this could mean you hit the ground

harder than necessary.

• Instead, allow the glider to fly at glide at full speed for your final

descent until you are around 1 metre above the ground. Apply

the brakes slowly and progressively to slow the glider down until

the glider stalls and you are able to step on to the ground.

• Be careful not to flare too hard at full speed as the glider might

climb again before stalling. If the glider does begin to climb, ease

off the brakes until it stops climbing, then flare again, but slower

this time. If this does happen, don't put your hands up! You

should keep the brakes at mid speed, stand up, be ready to run

and make sure you brake fully as you arrive on the ground.

• Lean forward out of your harness before the actual landing

(especially if it's turbulent), with your weight leaning forward

against the chest strap, and make sure your legs are ready for

the landing and a possible PLF.

• Choose the appropriate approach style in function of the landing

area and the conditions.

• Always land heading into wind!

• In light winds you need a strong, long and progressive flare to

bleed off all your excess ground speed. In strong winds your

forward speed is already low so you are flaring to soften the

impact as you touch down.

• In strong winds you need to turn towards the glider the second

your feet touch the ground. Once facing the wing pull smoothly

and symmetrically down on the brakes to stall the wing. If the

glider pulls you, then run towards it.

• If the wind is very strong, and you feel you might be dragged,

stall the glider with the C risers. This stalls the Buzz in a very

quick and controllable way and will drag you less then if you use

the brakes.

Packing

• Spread the glider flat on its top surface, then lay the lines on top.

The risers should be laid on the ground, at the centre of glider,

near the trailing edge.

• Take a wing tip and fold it in to the centre of the wing. Repeat

this until the glider is folded up and approx. 60 cm's wide.

• Do the same to the other side of the glider. Always make sure

that the leading edge is kept in one straight line, as it is

important not to badly crease the reinforcing fabrics in the

leading edge.

• Don't fold the glider along the same lines every time; any type of

folding reduces the strength of the fabric over time.

• Push out any remaining air by flattening the folded wing from the

trailing edge to the leading edge.

• Fold the glider so that the bundle is approximately the size and

shape of the OZONE rucksack. Never roll the wing up as this

introduces unnecessary stresses into the fabric.

• Always pack your Buzz as loosely as you can, as every fold

weakens the cloth on any paraglider.

• Finally, wrap the glider tie around the bundle and put it in the

stuff sack.

• Packing your glider using the concertina method, keeping the

mylar stiffners flat may prolong the life your glider.

ADVANCEDFLIGHTTECHNIQUES

Rapid Descent Techniques

Ozone would like to remind you that these manoeuvres should be

learnt under the supervision of a qualified instructor and always used

with caution. Never forget that properly analysing the conditions

before launch will help avoid the need to use these techniques.

Big Ears

Folding in the wingtips of the BUZZ increases its sink rate. This is

useful for staying out of cloud or descending quickly. To pull big ears

on the BUZZ, keep holding your brake handles and take the

outermost A-line (Baby A) on each side, then pull it down until the

tips of the wing fold under.

Do not use the brakes other than for re-inflation. For directional

control while using the Big Ears, you should use weight shift steering.

To reopen your ears, release the babyA : the glider should reopen

automatically. You can still help the reinflation by braking gently, one

side at a time to minimise the chance of inducing a stall.

IMPORTANT : You can land with the ears (you should release

the ears before final flare). But Ozone don't advise you to do

this when it's turbulent or windy due to the risk of a possible

stall and lack of precision in steering.

Big ears and accelerator

Once the big ears are in you can further increase the sink rate by

pushing on the accelerator bar.

NEVER try to pull the Big Ears in with the speed bar on. This can lead

to a major asymmetric deflation.

Big ears and spiral dive

Whilst it is possible to enter a spiral dive whilst holding in Big Ears,

the high forces applied to the lower lines could exceed the breaking

strain of the lines leading to equipment failure!

Ozone do not recommend the use of this manoeuvre!

Wingovers

The OZONE Buzz is not designed for aerobatic flying. The limit is

tightly banked S-turns, commonly known as wingovers. These must

not exceed 90 degrees of bank. Warning: uncoordinated wingovers

can lead to large asymmetric collapses and therefore should never be

executed near the ground.

B-Line Stall

B-stall is for fast descents in emergency situations only. B-stall is

performed by symmetrically pulling down on the B-risers.

To initiate the B-stall place your fingers between the lines above the

maillons on the B risers. Do not release the brake handles. As you

pull the B-lines down the airflow over the wing is broken and the

glider loses its forward speed but remains open and you will descend

at around 6 m/s.

If you pull too much B-line the glider will horseshoe and move around

a lot.

To exit the B-stall the B-risers should be released symmetrically and

in one smooth, progressive motion. The glider will resume normal

forward flight without further input. Check you have forward flight

again before using the brakes.

IMPORTANT : The pitching movement on exiting the B stall is

small but necessary. We recommend you do not brake the

glider until you are sure that the glider is flying again.

The load applied on the B lines during this manoeuvre is not

very good for your glider, only use it in emergency situations.

Spiral Dives

If you turn your Buzz in a series of tightening 360's it will enter a

spiral dive. This will result in rapid height loss. To initiate a spiral,

look and lean in to the direction you want to go, then smoothly pull

down on the inside brake. The Rush will first turn almost 360 degrees

before it drops in to the spiral. Once in the spiral you must apply a

little outside brake to keep the outer wing tip pressured and inflated.

Safe descent rates of 8 metres per second (500 ft/min approx.) are

possible in a spiral dive, but at these rates the associated high speeds

and G-forces can be disorientating, so pay particular attention to

your altitude.

To exit the spiral dive, return your weight shift to a central position

and then slowly release the inside brake. As the Rush decelerates

allow it to continue to turn until enough energy is lost for it to return

to level flight without an excessive climb and surge. The Rush shows

no indication of remaining neutral in the spiral dive, however some

parameters could interfere with its behaviour such as; wrong settings

of the chest strap (too wide), total weight in flight outside of the

certified weight range, or being in a very deep spiral at a very high

sink rate. You should always be prepared to pilot the wing out of such

a spiral dive. To do so smoothly use opposite weight shift and apply

a small amount of outside brake and the glider will start to resume

normal flight. Never attempt to recover from a spiral with hard or

quick opposite inputs as this will result in an aggressive climb and

surge.

IMPORTANT : Spiral dives with sink rates over 8 m/s are

possible, but should be avoided. They are dangerous and put

unnecessary strain on the glider. Spiral dives cause

disorientation and need time and height to recover. Do not

perform this manoeuvre near the ground.

Incidents

Deep Stall / Parachutal stall

It is possible for gliders to resume their normal shape on a very slow

release of the B-lines, but carry on descending vertically and without

full forward motion. This situation is called 'deep stall' or 'parachutal

stall'.

It is highly unlikely to happen on any OZONE glider, but should it

happen, your first reaction should be to fully raise both brakes and

the glider should return to normal flight. If nothing happens after a

few seconds, reach up and push the A-risers forwards or apply the

speeds bar to regain normal flight.

Ensure the glider has returned to normal flight (check your airspeed)

before you use the brakes again.

IMPORTANT : only a few cms of input from your brakes can

maintain your wing in the stall. Always release your wraps if

you have taken them!

Deflations

Due to the flexible form of a paraglider, turbulence may cause a

portion of the wing suddenly to collapse. This can be anything from

a small 30% (asymmetric) collapse to a complete (symmetric)

collapse

other option. This shouldn't be done unless you have been taught

how to do it and can only be done with a large amount of altitude.

Remember if the rotation is accelerating and you are unable to

control it, you should use your reserve whilst you still have enough

altitude.

IMPORTANT : A bad preparation on launch, aerobatic flying,

flying a wing of too high a level or in conditions too strong for

your ability, are the main causes of cravats.

ACROBATICFLYING

A specific standard of certification for aerobatic flying has not been

set up yet. Ozone wings although designed to the highest

specifications are, therefore, not certified for this type of flying. As

Aerobatic manoeuvres are very difficult and incorrectly performed

manouvers can put abnormal stresses on the glider and lead to loss

of pilot control, Ozone strongly recommend you not undertake this

style of flying.

TOWING

The BUZZ may be tow-launched. It is the pilot's responsibility to use

suitable harness attachments and release mechanisms and to ensure

that they are correctly trained on the equipment and system

employed. All tow pilots should be qualified to tow, use a qualified

tow operator with proper, certified equipment, and make sure all

towing regulations are observed.

When towing you must be certain that the paraglider is completely

over your head before you start. In each case the maximum tow

force needs to correspond to the body weight of the pilot.

PARAMOTRING

The BUZZ has been certified for paramotoring, see the website for

details. Its easy launch characteristics and its high stability at speed

make it a very good wing for this activity. OZONE provides as optional

risers especially designed for paramotoring: they are shorter than

normal and are equipped with trimmers.

We recommend you undertake qualified training before flying your

wing with a paramotor.

If you have a collapse, the first thing to do is to control your

direction: You should fly away from the ground or obstacles and other

pilots, or at least not to fly into them... Asymmetrical collapses can

be controlled by weight shifting away from the collapse and applying

a small amount of brake to control your direction. This act will most

of the time be enough for a full recovery of the wing.

Once a glider is deflated it is effectively a smaller wing, so the wing

loading and stall speed are higher. This means the glider will spin or

stall with less brake input than normal. In your efforts to stop the

glider turning towards the collapsed side of the wing you must be

very careful not to stall the side of the wing that is still flying. If you

are unable to stop the glider turning without exceeding the stall point

then allow the glider to turn whilst you reinflate the collapse.

If you do have a deflation which does not spontaneously reinflate,

make a long smooth progressive pump on the deflated side. This

pumping action should take about 2 seconds per pump. Pumping too

short and fast will not reinflate the wing and pumping too slow might

take the glider too close, or beyond, the stall point.

Symmetrical collapses reinflate without pilot input, however 15 to

20cm of brake applied symmetrically will speed the process. If you

simulate a symmetrical collapse during an SIV course it is important

to use both the A and Baby A risers and to pull evenly to induce a

symmetrical collapse. Use of just A risers or uneven pulling may lead

to the glider collapsing only in the centre section with the tips flying

forward to meet in the middle, leading to an increased risk of a cravat

occurring.

If your Rush collapses in accelerated flight, immediately release the

accelerator to slow down to trim speed and after a 90 deg turn the

canopy will reinflate and return to normal flight.

Cravats

When the tip of your wing gets stuck in the lines, this is called a

'cravat'. This can make your glider go into a rotation which is difficult

to control. The first solution to get out of this situation is to pull down

the stabilo line (red line on the B riser), while controlling your

direction, you must be careful with any brake inputs not to stall the

opposite wing.

If this doesn't work, a full stall (symetrical or asymetrical) is the only

Risers and hardware

Shackles - High quality micro maillons from Maillon Rapide.

Riser webbing - 20mm zero stretch polyester webbing.

Pulleys - Austri Alpin aluminium mini pulleys with brass roller.

All these components have been selected for their renowned quality

and durability.

CARINGFORYOURBUZZ

Many paragliders are damaged by careless ground handling. Here are

some things to avoid in order to prolong the life of your aircraft :

• DO NOT drag your wing along the ground to another take-off

position - this damages the sailcloth. Lift it up and carry it.

• DO NOT try to open your wing in strong winds without untangling

the lines first - this puts unnecessary strain on the lines.

• DO NOT walk on the wing or lines.

• DO NOT repeatedly inflate the glider and then allow it to crash

back down. Try to keep this movement as smooth as possible by

moving towards the glider as it comes down.

• DO NOT slam your Buzz down on the ground leading edge first!

This impact puts great strain on the wing and stitching and can

even explode cells.

• FLYING in salty air, in areas with abrasive surfaces (sand, rocks

etc.) and ground handling in strong winds will accelerate the

aging process.

It is recommended that you regularly CHECK your BUZZ, especially

after a heavy period of use, after an incident or after a long period of

storage.

Storage

Always store all your flying equipment in a dry room, protected from

the direct heat.

Your wing should be dry before being packed away. Heat and

humidity are the worst factors in damaging your glider. (Storing a

damp glider in your car under the sun would be terrible for example).

Dry your wing preferably out of the sun, in the wind. Never use a hair

dryer, etc.

MATERIALS

All OZONE gliders are made from the highest quality materials

available. Your Ozone BUZZ is constructed from:

Upper-surface

Gelvenor

Double silicone-coated and polyurethane-coated Ripstop Nylon

Selected for its durability and resistance to both UV damage and

general wear and tear. In the air and on the ground the top surface

of your glider takes more abuse than any other part, hence we

choose Gelvenor for the top surface of all our wings.

Lower-surface

Porcher-Marine 37 g/m2 Polyurethane coated Ripstop Nylon

Probably the most commonly used fabric in paraglider construction.

Porcher Marine has been tried, tested and proven to be the most

effective all round fabric.

Internal Ribs

Porcher-Marine 45 g/m2 and 37 g/m2 High tenacity Skytex+ Ripstop

Nylon.

Selected for stability and resistance to stretch - vital if a glider is to

keep its safe-flying characteristics for a long time.

Leading-edge reinforcement

Double-laminated Mylar.

Selected for long-term durability. Keeping the leading edge shaping

precise ensures that your glider's characteristics remain consistently

good season after season.

Lines

Lower cascades - Edelrid Aramid, 6843 series - 200 kg's breaking

strength - 1.8 mm

This line is the reference for its high strength and its low stretch in

the time.

Middle cascades - Liros DSL - 140 kg's breaking strength - 1.1 mm

Upper cascades - Liros DSL - 70 kg's breaking strength - 0.95 mm

Special heat treated dyneema in a ultra finely woven sheath creates

a line material that is, not only highly resistant to damage through

wear and tear, but also incredibly light weight too.

www.aerorosport.de if you are from Germany or Austria).

Caring Tips

• Your Ozone wing has got an opening closed using velcro on the

trailing edge of the tip called 'butt hole'. This has been designed

to easily empty all the things which have been accumulating in

your wing (sand, leaves, rocks, mobile phones etc).

• If you fly with a wrap, you should regularly undo the twisting that

appears on the main brake lines. By twisting the line become

shorter and you can end up with a constant tension on the

trailing edge (which can lead to problem on launch, stalling,

glider not flying symmetrically, ...)

• Change your main brake lines ifthey are damaged.

MAINTENANCE CHECKS

Your wing, like a car, should be technically checked to ensure proper

airworthiness.

If you ever sell your BUZZ, you should give to the buyer the actual

revision certificat.

Your wing should be checked by a qualified professional for the first

time after 30 months, and thereafter every 24 months.

However, if you are a frequent flyer (more than 80 hrs per year), then

we recommend, that you get your glider checked after every flying

season.

If your glider is used professionally for training purposes or for

professional tandem flying then a complete maintenance check must

be carried out every 12 month.

The checker should inform you about the condition of your glider and

if some parts will need to be checked or changed before the next

normal service check period.

The sail and the lines don't age in the same way : it is possible that

you'll have to change part or all of the lines during your wings life.

This is why it is also important to do a regularly check up to know the

condition of all the components of your glider.

We recommend that the check up is carried out by a qualified

If you land in the salt water, you must clean it with fresh water first

and then dry it.

Take care that no insects get packed away with the wing they may

eat the cloth and make some holes in a bid to escape, they can also

leave acidic deposits if they die and decompose.

Cleaning

Any kind of wiping/scratching can damage the coating of the cloth.

We recommend for cleaning your BUZZ, you use a soft cloth

dampened only with water and to use gentle movements little by

little across the surface.

Never use any detergent or chemical cleaners

Wing Repairs

Amateur repairs can do more harm than good. Always let a

registered dealer or the manufacturer carry out major glider repairs.

If you damage the sail:

If the rip is small, you can fix it yourself. You'll find all the materials

in the repair kit you need.

On the Gelvenor fabric, because of the silicon coating, the sticky

ripstop will not stick. You will have to use a very thin coat of silicone

glue, available from DIY shops, to stick a piece of Gelvenor cloth on

the tear.

The Porcher Marine fabric can be simply mended with the sticky rip

stop / spinnaker tape.

When cutting out the patch remember to allow ample overlap around

the tear and round the corners of the patch.

You can find more information about repairing your wing on the

Ozone website, including step by step instructions with pictures.

If you damage a line:

Any line that is damaged should be replaced. It is important that the

replacement line is from the same material, has got the same

strength and the same length. You can check its length against its

counterpart on the other side of the wing, to make sure that it is

symmetrical. Once the line has been replaced, inflate and check the

glider before flying. If you do not have access to an Ozone dealer

you can order individual lines at www.flyozone.com(or

components of the wing (stitching, ribs, diagonals, lines, tabs, ...)

should be checked.

Finally, if in doubt, a flight test that confirms that the wing behaves

normally can be done by the professional..

IMPORTANT : Take care of your glider and make sure you have it

checked according to the above schedule: This will ensure you hours

of safe flying.

MODIFICATIONS

Your Ozone Buzz was designed and trimmed to give the optimum

balance of performance, handling and safety. Any modification means

the glider loses its certification and will also probably be more difficult

to fly. For these reasons, we strongly recommend that you do not

modify your Buzz in any way.

OZONEQUALITY&SERVICE

At Ozone we take the quality of our products very seriously, all our

gliders are made to the highest standards in our own manufacturing

facility. Every glider manufactured goes through a stringent series of

quality control procedures and all the components used to build your

glider are traceable. We always welcome customer feedback and are

committed to customer service. We will always undertake to fix

problems not caused by general wear and tear or inappropriate use.

If you have a problem with your glider please contact your

dealer/distributor who will be able to decide upon the most

appropriate action. If you are unable to contact your dealer then you

can contact us directly at info@flyozone.com

professional.

You are responsible for your flying kit and your safety depends on it.

Take care of it and have regularly a inspect all of its components.

Changes in a wings flying behaviour, are also indicators of the gliders

aging, if you notice any changes you should have the wing checked

before flying again.

These are the basic elements of the check up (full details and

permissable figures can be found on our website):

Porosity is measured with an porosity meter, the time taken by a

certain volume of air to go through a certain surface of the cloth. The

time in seconds is the result. A measurement is done in a several

places on the top surface along the span of the glider behind the

leading edge.

The tearing resistance of the cloth - A non-destructive test following

the TS-108 standard which specifies minimum tear strength for sky

diving canopies is executed. .

Strength of the line - The centre lines are tested: The uppers, the

middles, the lowers on the A, B, Cs are all measured. The reason for

this is because these are the lines which bear most of the loads.

Each line is tested on a testing table where they are pulled until they

break. The breaking value is recorded. The minimum value is 8 G for

all lower A+B lines and 6 G for all lower remaining lines, calculated

from the maximum certified flying weight of the glider. The added

minimum strength for middle lines and top lines is the same.

If the breaking strength is too close to the minimum value calculated,

the professional will give a period after which you'll have to test the

strength of the lines again.

Lengths of the lines - The overall length (riser lines + mid lines +

upper lines) has to be checked under 5DaN of tension.

The difference between the measured length and the original length

should not exceed +/- 10mm.

The changes that could appear are a slight shrink on the C and a

slight stretch on the A, B. The consequences of these changes can

include a slower trim speed, difficult inflation etc.

Full check - A full visual check should be carried out: All the

SUMMARY

Safety is paramount in our sport. To be safe, we must be trained,

practised and alert to the dangers around us. To achieve this we must

fly as regularly as we can, ground handle as much as possible and

take a continuous interest in the weather. If you are lacking in any of

those areas you will be exposing yourself to more danger than is

necessary.

Flying is an immense subject which takes years to learn, so let your

experience build slowly, don't put pressure on yourself, you have

plenty of time to learn as many people fly well into old age. If

conditions aren't good now then pack up and go home, there is

always tomorrow.

Don't overestimate your abilities, be honest with yourself. As the wise

saying goes, 'it is better to be on the ground wishing you were in the

air, than to be in the air wishing you were on the ground'.

Every year many pilots get hurt launching; don't be one of them.

Launching is the time that you are most exposed to danger so

practice it lots. Some launch sites are small and difficult and

conditions aren't always perfect. If you're good at ground handling

you'll be able to confidently and safely launch whilst others struggle.

You'll be less likely to get hurt and more likely to have a great day's

flying.

Ground handling is also a form of flying. It teaches you to be

sensitive to your glider and to understand the feedback it sends you,

so practice as much as you can.

Finally, RESPECT the weather, it has more power than you can ever

imagine. Understand what conditions are right for your level of flying

and stay within that window.

Happy flying & enjoy your Buzz.

Team Ozone

SOMMAIRE

Ozone Vous Remercie ............................................................

Action!!! .............................................................................

L'Euipe Ozone ....................................................................

Votre Buzz ..........................................................................

Le Sac De Portage Ozone .......................................................

Les Freins ...........................................................................

Les Élévateurs .....................................................................

L'Accélérateur ......................................................................

La Sellette ...........................................................................

Le PTV ................................................................................

Vols De Prise En Main ............................................................

Préparation .........................................................................

Check List Avant Décollage ....................................................

Décollage ............................................................................

Caractéristiques De Vol .........................................................

Vol Normal ..........................................................................

Pilotage Actif........................................................................

Virage ................................................................................

Atterrissage .........................................................................

Pliage .................................................................................

Vols Avancés .......................................................................

Techniques De Descente Rapide ..............................................

Les Oreilles .........................................................................

Oreilles Et Accélérateur .........................................................

Oreilles Et 360 .....................................................................

Wing Over ...........................................................................

Descendre Aux B ..................................................................

360 Engagés .......................................................................

Incidents De Vol Et Recommandations .....................................

Parachutal ...........................................................................

Fermetures .........................................................................

Cravates .............................................................................

La Voltige ............................................................................

Treuil ..................................................................................

Paramoteur .........................................................................

Matériaux De Fabrication .......................................................

Précautions Générales ...........................................................

Rangement .........................................................................

Nettoyage ...........................................................................

Réparation ..........................................................................

Astuces ...............................................................................

Révision ..............................................................................

Modification .........................................................................

Qualité Ozone .....................................................................

Conseils Généraux ................................................................

Disposition Des Elévateurs .....................................................

Carte de suivie

OZONE VOUS REMERCIE

d'avoir choisi de voler sous une BUZZ.

L'équipe OZONE, constituée de passionnés de vol libre, se consacre

à la fabrication d'ailes agiles, d'une maniabilité très caractéristique,

optimisant d'incontestables performances tout en vous assurant la

sécurité dans la turbulence.

Notre travail de recherche et de mise au point se concentre sur le

meilleur compromis maniabilité/sécurité. Confiance en soi et en son

matériel constitue une garantie de progression et de réussite bien

plus importante que des performances pures et chiffrées. Demandez

aux compétiteurs et aux aventuriers qui accomplissent exploits et

résultats sous leurs parapentes OZONE!

Enfin, toujours en tant que pilotes, nous avons conscience de

l'importance de la dépense que représente l'achat d'une aile. Le

rapport qualité / prix exige une production irréprochable pour faire la

différence. Afin de maîtriser les coûts de production tout en assurant

la plus grande qualité de fabrication, nous fabriquons désormais nos

produits dans notre propre usine. Cette solution nous garantie aussi

une qualité de contrôle parfaitement fiable.

L'équipe des pilotes est basée dans le Sud de la France. Cette région

avec les sites de Gourdon, Roquebrune et le Lachens garantit 300

jours de vol par an. C'est un atout incontestable pour la mise au point

de la gamme OZONE.

Ce manuel de vol vous aidera à obtenir le meilleur de votre BUZZ.

Vous y trouverez des explications détaillées concernant sa création

ainsi que des astuces et conseils pour savoir comment la piloter au

mieux, en assurer le meilleur entretien afin de préserver sa longévité

et donc son prix de revente sur le marché d'occasion. vous trouverez

à la fin de ce manuel les spécifications techniques de votre

parapente: le diagramme de montage des suspentes ainsi que leurs

longueurs.Gardez ces données techniques , elles vous seront

nécessaires en cas de remplacement d'une ou plusieurs suspentes.

Si vous avez besoin d'informations complémentaires, votre

revendeur, votre école ou l'un d'entre nous chez OZONE restons à

votre disposition.

Avant de voler sous votre BUZZ pour la première fois il est

très important que vous lisiez attentivement ce manuel de

vol.

Si vous revendez votre Buzz assurez vous de transmettre ce

manuel au futur propriétaire .

Sur notre site web www.flyozone.com une mise à jour

permanente vous informera des dernières communications

concernant notamment la sécurité et les spécifications

techniques de votre Buzz. Merci de consulter ce site

régulièrement.

ACTION!!!

Tous les sports aériens sont potentiellement dangereux et présentent

des risques d'accidents dont les conséquences peuvent entrainer des

blessures et des traumatismes graves voire mortels.En tant que

propriétaire de cette Buzz d'Ozone, vous assumerez tous les risques

liés à son utilisation.

Une utilisation inappropriée et ou un mauvais entretien de votre

matériel accroissent ces risques.

Les parapentes Ozone conviennent aux pilotes qualifiés ainsi qu'en

formation.En aucun cas le fabricant, l'importateur ou les vendeurs ne

peuvent etre tenus responsables quant à l'utilisation de ce produit.

Assurez votre formation dans des écoles compétentes. Entrainez

vous régulièrement en controle statique au sol et autant que vous le

pouvez. En effet un controle approximatif de l'aile sur les phases de

gonflage et décollage est la principale cause d'accidents en

parapente.

Continuez à vous formez régulièrement afin de suivre l'évolution de

notre sport, des techniques de pilotage et du matériel.

Ne volez qu'avec des ailes dûment homologuées et respectez la plage

de poids, un harnais équipé d'une protection dorsale muni d'un

parachute de secours. Votre matériel ne doit avoir fait l'objet

d'aucune modification et doit être en bon état et révisé

régulièrement.

Une visite prévol de tout votre matériel et cela avant chaque vol est

indispensable. N'essayez jamais de voler avec un equipement abimé

ou non adapté à votre expérience.

Volez toujours équipé d'un casque, de chaussures adéquates et de

gants.

Tout pilote doit justifier d'avoir le niveau de formation et d'expérience

requis et doit avoir souscrit au minimum à une assurance en

responsabilité civile aérienne.

Vérifier que l'ensemble aile, harnais, expérience, conditions

aérologiques, état physique et mental soit cohérent et respecté à

chaque vol.

Accorder une importance toute particulière à l'endroit oÙ vous allez

voler ainsi qu'aux conditions météo.Si un doute existe abstenez vous

de voler et de toutes façons ménagez vous d'importantes marges de

sécurité.

Eviter absolument de voler sous la pluie, la neige, dans du vent fort,

en conditions turbulentes et les nuages.

Seulement si vous faîtes toujours preuve de rigueur dans vos

jugements, vous vivrez alors de nombreuses et heureuses années de

vol.

Le plaisir est le moteur de votre activité.

VOTREBUZZ

La Buzz s'adresse aux pilotes occasionnels qui aprennent et

découvrent ce formidable sport aussi bien qu'aux pilotes plus

expérimentés à la recherche d'un maximum de sécurité, performance

et plaisir. La Buzz a tout ce dont vous avez besoin pour progresser à

tous niveaux.

Notre objectif en concevant la Buzz était de produire une "DHV 1-2"

facile tout en gardant la maniabilité Ozone, la sécurité et la

performance. La Buzz a été homologuée en Dhv 1-2 avec presque

tous les tests en DHV 1 (sauf accélérés). Dav et l'équipe des pilotes

ont travaillé dur pour créer cette aile tolérante tout en conservant

une bonne maniabilité et sensations dont le pilote a besoin pour

progresser.

En controle au sol, la Buzz est superbe. Les gonflages dos ou face à

l'aile sont simples. La montée est douce et progressive avec une

pression constante sur les élévateurs, ceci permet au pilote de

toujours sentir oÙ l'aile se situe pendant la montée. Le controle en

tangage est évident avec trés peu de tendance à dépasser.

En l'air la Buzz est un plaisir, la pression aux commandes est parfaite,

augmentant graduellement au fur et à mesure jusqu'à devenir plus

importante quand le point de décrochage est atteint. La Buzz offre un

feed back trés juste à travers les freins et les élévateurs, pour vous

aider à progresser dans le thermique et améliorer votre pilotage en

air turbulent sans toutefois vous submerger par trop d'informations

inutiles.

L'aile est solide en tangage, permettant de traverser efficacement les

zones turbulentes par une bonne résistance aux fermetures, mais

aussi en améliorant les caractéristiques de réouverture.

La maniabilité est surprenante, les changements de direction aisés

tant pour mordre dans le thermique que pour recentrer un virage.

L'inclinaison en virage est facilement controlable en soaring ou

thermique par une légère action sur la commande extèrieure.

Virages doux ,à plat ou sur la tranche, "ça va bien le faire, comme

vous l'aimez".

Le taux de chute et la finesse sont excellents pour une aile si sure, la

L'EQUIPE OZONE

Toute l'équipe Ozone est animée depuis le début par la même passion

du vol et de l'aventure. Cette passion, vous la retrouvez dans cette

quête où nous cherchons à créer des parapentes encore plus

ludiques, encore plus sûrs et meilleurs.

La conception des parapentes est dirigée par le pensif Dav Dagault et

par Rob Whittall, 'celui qui n'arrête jamais', tous deux pilotes de

renommée, dont l'immense expérience acquise en compétition et au

travers de multiples aventures est désormais canalisée dans leur

création. Ensuite interviennent les pilotes tests :Jérome Canaud, un

réel esprit acro ainsi que Russel Ogden, compétiteur de haut niveau,

tous deux étant également instructeurs de parapente. Ils font subir

toute sorte de séries de manoeuvres aux derniers protos de Dav.

De retour au bureau Mike "Da Boss" Cavanagh et Sam lowe veillent

au bon fonctionnement général de l'entreprise.. Claire Drury quant à

elle met tout en oeuvre pour que votre aile soit livrée le plus

rapidement possible. Cachés dans un coin, évitant de se faire mal en

jetant un coup d'oeil aux conditions dehors, Marcus King et

Emmanuel Prissette s'occupent de la publicité, des vidéos, brochures

... et gèrent l'informatique en général. Un nouveau venu ,Ivan Bellia

qui a la charge de la nouvelle partie accessoires. Karine Marconi

s'assure de la comptabilité et que nous ne dépensons pas trop

d'argent .Vous aurez la chance en nous téléphonant d'ètre accueilli

par la charmante voix de Nicky watts.

Notre usine de production est dirigée par Dc Dave Pilkington, qui

travaille sans répit à fabriquer les ailes Ozone et les différents

prototypes, ainsi qu'à prospecter de nouveaux matériaux et de

nouvelles techniques de fabrication pour les produits futurs. Il est

secondé par Ngan et dirige 170 employés.

montée aux nuages et le cross en seront d'autant plus faciles.

La large plage de vitesse utilisable de la Buzz vous aidera à sortir des

zones descendantes ou à pénétrer un vent de face.

La Buzz est un choix judicieux pour les nouveaux pilotes ou pour ceux

recherchant un excellent compromis sécurité/performance. Elle vous

emmènera loin, en confiance et avec le sourire garanti apres chacuns

de vos vols.

Enfin nous sommes toujours trés heureux d'entendre vos critiques

sur nos ailes, bonnes ou mauvaises, alors n'oubliez pas de nous tenir

au courant de vos aventures avec la Buzz.

Le sac de portage OZONE

Le sac est étudié pour avoir un portage confortable et efficace

(ceinture matelassée et bretelles ergonomiques réglables) tout en

gardant un volume adapté à tout votre matériel de vol. Les poches

latérales et supérieures facilitent le rangement de l'ensemble de

votre équipement. La sangle de compression et le sac de voile

garantissent un bon maintien de votre voile une fois pliée.

Les freins

Les freins sont préréglés en usine et vérifiés.

Ceux-ci seront légèrement longs car nous pensons qu'il vaut mieux

avoir à piloter avec éventuellement un "tour de freins" autour des

mains ou prise en dragonne. (meilleure précision de pilotage).

Mais si jamais ce réglage d'origine ne vous convenait pas, et que

vous décidiez de modifier celui-ci, vous devez absolument respecter

les précautions suivantes:

• Assurez-vous de la parfaite symétrie des longueurs des deux

freins.

• Si une poignée de frein a dû être détachée de sa suspente,

vérifiez que la suspente rattachée à nouveau passe bien dans sa

poulie et empreinte le bon chemin. Le noeud de chaise est le plus

adapté pour la liaison poignée/drisse de frein.

• Quand les poignées de freins sont lâchées en vol, le suspentage

de freins doit décrire le profil d'un arc (lobe) depuis le bord de

fuite jusqu'aux élévateurs et non pas être tendu comme les

autres suspentes afin de ne pas brider ni déformer ce bord de

fuite.

• Il doit y avoir une garde, un jeu d'au moins 10 cm entre le départ

de votre action à freiner et le début de déformation du bord de

fuite. Ce jeu permet d'utiliser l'accélérateur sans déformer le

bord de fuite.

IMPORTANT - Si jamais une poignée de frein venait à se

détacher ou à casser, vous pourrez toujours vous diriger et

piloter en utilisant les 2 élévateurs arrière. Attention

l'amplitude de traction doit être plus faible pour obtenir un

virage, utilisez également votre sellette.

Les élévateurs

Nous avons privilégié la simplicité et avons conçu la BUZZ avec

seulement 3 élévateurs. Chaque élévateur est recouvert d'une sangle

de couleur différente, afin de pouvoir les identifier au sol comme en

l'air, rapidement et sûrement.

• Les A sont Rouges. Vous noterez que les A sont divisés en deux.

Le brin qui se trouve à l'arrière, ne comportant qu'une seule

suspente est le " BabyA ".Il vous permet de faire les oreilles

aisément tout en gardant les commandes de freins en main.

• Les B sont Bleus

• Les C ou arrières sont Noires

L'accélérateur

Il est à fixer à l'aide des crocs fendus sur le devant des élévateurs A.

(ajuster ensuite la longueur et le faire passer dans les emplacements

de la sellette prévus à cet effet).

Pour ajuster l'accélérateur, installez vous dans votre harnais posé sur

le sol. Un assistant tiendra les élévateurs tendus vers le ciel, dans

leurs positions de vol par rapport au pilote. Ajustez alors la longueur

de la cordelette de façon à ce que la barre rigide de la pédale

d'accélérateur (fournie avec la voile) soit à 10 cm sous votre harnais.

Vos talons doivent alors pouvoir se poser facilement sur la sangle

(partie souple de l'accélérateur).

Le réglage de l'accélérateur doit être suffisamment "long" pour qu'en

vol normal, non accéléré, le système ne tire pas sur les élévateurs,

mais assez court pour pouvoir accélérer à fond les jambes tendues.

En poussant à fond sur la sangle (partie souple) de l'accélérateur

vous devez atteindre la moitié de la vitesse que le système permet

de gagner. C'est la vitesse accélérée la plus couramment utilisée :

c'est là où on trouve le meilleur compromis vitesse, finesse, solidité.

La page charge ...

Ozone buzz Le manuel du propriétaire

Marque: Ozone

Modèle: buzz

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Ozone buzz Owner's manual
Deutsch: Ozone buzz Bedienungsanleitung

Ozone buzz Le manuel du propriétaire

Ozone buzz Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents